Sorry, newbie so sorry if answerd else where
xda II running fine, put in my new kingston 528meg SD card, seems ok. ran xbackup for first time and is slow so left it to run overnight. woke up message says done ok. BUT now xda can't see storage card at all!! :?
tried reset, same. tried 32meg SD card out of wifes Nokia: sees that fine. cant try kingston SD in Nokia cos its a different physical size
Any ideas? or can you reformat these SD cards in the xda?
Thanks
if pocket mechanics cant formet it because it cant see the card then
a sd reader for the pc they are only like 10$ would most likely see it
or you could try and see if your wife's phone could format it
or another device which use SD cards like a camera
just tried CNetX flashformat but it cant see the card damm why are SD cards different sizes ( wont fit in wifes nokia and camera is Compact flash memory) arrgggggg
are you sure that the nokia use sd?
because the nokia's i've seen use mmc flash which look just like sd but thinner and sd devices can use mmc but not the other way around
did you try pocket mechanics?
doh my mistake yup the nokia 6230 is mmc
tried pocket mechanics to no avail. mate popping round with his xda ii in a mo so i can try his card and vice versa. hes going to take my card and try and format it with his pc which has a built in reader
ill keep you posted :idea:
UPDATE
Card is dead! tried it in mates xda ii and his pc and it can't be seen. off to post it back to China! ( ebay rules )
xBackup isn't what killed your card - it was the XDA itself.
I have destroyed a 1GB Toshiba, and a 512MB Toshiba so far.
My 256MB Kingston has been fine.
...
Put the card to a card-reader/writer(on a PC) and try to check it for errors(Scandisk/Chkdsk). If it doesn't help,try to format the card with standard FAT32 filesystem... My experience is,that the filesystem can be injured the same way as a floppy when you remove it(cut-off data transfer) before is any file not closed for write yet. I loosed once all my important data from SD. The /Storage is the most secure place for my important documents,that I know.
Related
After exchanging from MMC card to SD card the PPC wants to reformat the SD card (the one with all your programs and back up etc on it [1GB]). The other SD card of 256mb is not recognized at all anymore (so much for all my music). Could there be a connection from the fact that I have had a MMC card inserted before? I already have put back the MMC card to see if some program had not been closed properly. ALthough I fortunately have a recent backup of my 1GB SD card ( but not my 256 mb card) I would prefer to find a more sophisticated solution than to reformat my SD card. Who has a solution for me? Thanks.
Is there a bug between MMC and SD?
SD Card getting corrupted by MDA II !!
Hello,
I have MDA ii since last two months and my device has corrrupted my extreme - 512 SD Card Twice and after corruption it's not even recognized by PPC , USB card reader and my camera.
I have installed omeg a_Red OS. on my MDA ii
Following are the details of my device
ROM Version : 2.0.6.00 WWE
ROM Date : 06/14/2004
Radio Version : 1.18.00
Protcol Version : 1337.38
ExtROM Version : Diamond 1.2 se
Please help
try to open it with card reader. and back up first.
Any luck?
For some unknown reason my XDA IIi no longer reads the SD card!
In about it says "Expansion Slot : In Use", but explorer can't see it!
Any help please?
Loads of pictures and movies on there too.
ross1234 said:
Any luck?
For some unknown reason my XDA IIi no longer reads the SD card!
In about it says "Expansion Slot : In Use", but explorer can't see it!
Any help please?
Loads of pictures and movies on there too.
Click to expand...
Click to collapse
have you been able to read your SD card at all. I am having the same problem with my XDAIIi. Cannot read the card on any device or PC.
Yep it worked fine straight away, hence I had "Loads of pictures and movies on there too. "
Does any one know what it going on?
maybe the card is dead
seen it happening to a CF card once all of a surden it just died
and would not work in the digicam sdreader ..,....
Nooooo, is that it then?!?! data none recoverable?
Does this happen often? Should I be able to get my money back? What's the point of having 1 gb of storage if at any moment it disapears with all your info on?!
when it happent with the CF card for the camera it was 100% dead and all data was lost
of cause i cant say for sure if it could be saved or not
but no money was thrown after the project
i mean when soo much time have passed who care who was firing the shots from the grassy nole
and to answer you other question then no it should be pretty rare
that a flash card die seen tests where they put a cam on a bridge and blew it up and found the flash card and it still worked
and also this
http://news.com.com/Lost+at+sea,+found+in+flash+-+page+2/2100-1041_3-5780047-2.html?tag=st.num
but i would try some different SD readers before writting it off as dead
i had exp with some sd readers which sucked
and others my own sandisk 8-1 flash reader had no issues reading the card
That's the route I'm trying, installing card reader on pc.
Cheers.
Expect a post in the near future "SD Card reader not working on XDA IIi"
:twisted:
I am also currently in the same soup. Whe I let the xda2 format the sd, it works alright in xda storing files etc, but not recognised by laptop and it also asks to format it.
Victor
I am giving up on my card. As it was only 2 days old I am returning it and hoping for a replacement. My friend has sent his XDA II back to O2 as it has destroyed 3 SD cards within the space of two weeks. All different makes. My card was a new 512MB high speed card. I had been using an older Sandisk 256MB card with no problems for several months and decided to upgrade. I will try another card that I have - Sandisk 512MB (slow card) and see if that is OK.
O2 have said that this is not a known problem!!! What do they know???
O2 also gave me the same reply!
Idiots.
Their solution was "Take it to a store, and an engineer will look at it"
Yeah right, you mean a dummy who is trained to follow a 10 stage analysis process and tell you at the end "Sorry, I don't know what the problem is, shall we send it back to HTC for analysis?"
My guess is that the handset is not negotiating the operating voltage correctly, and is frying certain cards.
My 512MB + 1GB Toshiba cards fried within 2 weeks of new.
My 256MB Kingston is still going strong after 9 months (touch wood!)
Now almost 90 quid down the drain, and I'm going to try O2 as a last resort!
(Might print this forum too
This has been happening quite a lot recently. I made a post regarding the same happening to my 512mb Kingston card here:
http://forum.xda-developers.com/viewtopic.php?t=25566
Somewhere in that thread are links to THREE other recent threads regarding fried SD cards. I think there is a hardware fault in the device...
Anyway, I seem to remember the seller boasting about some warranty on their site, so I'm going to try to return it...
I just spoke with the supplier... he was very accomodating. This is what he said:
Whilst the Kingtston card is of superior quality to the Viking they are both using Toshiba components and we have had customers experience a similar issue when using either card with the XDAii where it would seem that the device 'kills' the card... I would recommend a Lexar branded xD card for use in the XDAii rather than any Toshiba based card. If you are interested, you could purchase the Lexar card from us and I can issue you with a full refund for your current SD card (including postage) as I feel the Lexar card would be more suitable for your use.
Click to expand...
Click to collapse
Sounds more and more like a device problem! Oh oh!
mmm_ok said:
I just spoke with the supplier... he was very accomodating. This is what he said:
Whilst the Kingtston card is of superior quality to the Viking they are both using Toshiba components and we have had customers experience a similar issue when using either card with the XDAii where it would seem that the device 'kills' the card... I would recommend a Lexar branded xD card for use in the XDAii rather than any Toshiba based card. If you are interested, you could purchase the Lexar card from us and I can issue you with a full refund for your current SD card (including postage) as I feel the Lexar card would be more suitable for your use.
Click to expand...
Click to collapse
Sounds more and more like a device problem! Oh oh!
Click to expand...
Click to collapse
I just had 2 SD cards blow up, a Viking 1GB card and a PNY 512 Mb card. Who is your supplier?
Hi,
I have a problem in recognizing my Transcend 2 GB SD-Card.
During operation the MDA Pro "looses" my storage card. I do not need to move the MDA. It also happens when it is on the table.
When I eject the card and put it in again it is recognized again.
Do you have a suggestion what this can be?
Mike
****, I just ordered the same card two days ago. Should arrive today or tomorrow. I let you know what happens.
Unless your card is faulty, try reformatting the card (I know you don't usually have to do this staight out of the box). I have had this problem before, but on the i-mate jam and it would read the card in my PC, but not my LapTop, which has a dedicated SD slot. Go figure. Tried formatting to FAT and FAT32, but I think it doesn't make too much of a difference. For me it came down to the type of SD card being used!
My 1GB Scandisk card works flawlessly and quickly wherever I put it, but my 2GB Scandisk SD Ultra II only works in my PC and transfer rate seems noticeably slower. :?
I already formatted the SD-Card. I also tried Low Level Format with
Pocket Mechanic.
I haven´t found failures with a r/w test. On the PC there are no problems.
Mike
Send it back! :evil:
Send it back! :evil:
Having 2GB MMC works fine with me... Thank God.. was worried
I have the same problem with the Transcend 2GB card. When syncing Avantgo to the card I get a "write teimeout" error. The card is still there when I look at it with the explorer.
2GB SD card
I have no problems with a 2GB Sandisk SD card.
I bought an Integral 2GB High Speed SD card. Initially, my JASJAR refused to recognise the card as anything more than 128 MB. I tried formatting it with Pocket Mechanic (Low level and normal format) - still 128MB. My notebook (with a built-in SD card reader) also saw it a 128 MB. My EPSON card reader did not recognise it at all.
After finding a post on a forum through Google, I found out that the iMate JAM apparently creates a new partition on the 2GB card, and that it was a known problem (for the JAM).
Using Partition Magic, we saw that it in fact created three partitions (128 MB, 1GB and the remainder, but we could not format or use the other).
My husband got the brilliant idea to put the card in my Nikon CoolPix, which told us that the card was not formatted. He told the camera to format it, which worked -- I can now use the card as 2GB in both my JASJAR and my laptop.
I hope this helps somebody ...
Re: 2GB SD card
paulrousseau said:
I have no problems with a 2GB Sandisk SD card.
Click to expand...
Click to collapse
Which type?
THX!
Got no probs on my scandisc ultraII card on jasjar either, but my laptop won't recognise it! :?
Good thing I have a PC too! :lol:
No problems with my UltraII card either...
I always format my cards with my PC or Laptop before using them, and it's always been fine in PPC, PC, and Laptop.
When I inserts the SD card (Power Disk 1GB), he gets a question whether he wants to format the card so that the JAM will recognize it. If he chooses to format the card, he gets a message that it can not be done and he should reinsert the card or replace it.
I tried a different 1GB SD card and it did not work either. A 256 card worked fine. PL
Is the card write protected?
That little switch on the side
http://images.google.co.uk/images?q...nthenet.com/2005/2997/pix/gallery/SD512mb.jpg
NO
No ..
maybe that brand of card is not compatible with JAM. Try common ones like Sandisk, Kingston, Transcend, Lexar, Panasonic those work without any issues. 2Gb and 4Gb cards are a problem as some will work and some won't.
The other thing is that the Powerdisk Card is faulty? have you tested it using a card reader or a digital camera?
hi, i have a question about SD cards. how can i test my 512 sd card (don't know brand, when i bought the S100 the card hadn't any stickers on it) to see its speed? is there any app? thanks!
you can use a tool from handango.com like Pocket Mechanic or SKTools
My MDA has stoped seeing my memory card. I have a 2gb Moby Memory card. Is there a seting to turn it on. My laptop has no problem with the card.
Did you try to reformat it on your laptop? format it with the FAT file system and get yourself a trial copy of pocket mechanic, you can get it from handango, and reformat it with the tools in that program. I experienced the same thing with my sd card, and after formating it the first time on my pc it still wouldn't recognize it, I then formatted it with FAT filesystem instead of FAT32 and my MDA recognized it, hope this fixes your predicament also.
Try formatting it with a different unit. I used my digital camera to format the miniSD, ofcourse I used an adapter to make it SD. I also lost my miniSD during the first two days I got it. I have a Patriot 1gb miniSD, comes with an adapter for SD.
Try formatting it with a different unit. I used my digital camera to format the miniSD, ofcourse I used an adapter to make it SD. I also lost my miniSD during the first two days I got it. I have a Patriot 1gb miniSD, comes with an adapter for SD.
I had the same Problem.
This is a known bug. Paste a sticker to make it thicker on the sd-card.
When I formated using my camera, it reduced the memory gown to 1gb. That still did not work until i used a bit of selotape to make the card thicker did it work. Thank for all your help.
hi guys your forum is great cant stop reading.But i have an issue i recently bought an 4gb mini sd card for my phone the card works but is like it works when it feels like if i put it in and wait for a while or just randomly turn the phone off and on it will work i format it using my card reader through windows on fat32 and all the thing is it works but i should not have to be going through all of this for the sd card to work.
My next problem is i recently upgraded to SNN Edition Version 3.0 LITE and i have to say i love it but before my phone could detect my sd card and from i did i upgrade its not detecting my card at all to be on the safe side i took out the card before the upgrade and now its not detceting at all please can any one help me is there a patch i can use or something HELP!!
i think try to format via fat16 option. i had earlier 2gb kingston card sdmini after formatting it works welll
i was doing some reading and i was told that 2gb is the highest for formating with fat16 i have a 4gb card so this cant work for me a even look in properties and the only option is fat32.any body else as any more in puts.
4GB cards are almost exclusively multilayer, and cannot be read by the Wizard's card reader. You are basically limited to 2GB, and it should be formatted as FAT, not FAT32, as was already noted. If there's a 4GB model that's single layer, that's great, but I don't know about it. (...not saying I'm the definitive authority, either...)
which program can i use in windows to format the card in FAT and not FAT32 and as i said before the phone could read the card before i did the upgrade the only thing its takes a while for the phone too detect the SD card and thats in FAT32 format but i will try the FAT format.
from my experience you can't put ANY 4gb minisd card into the wizard and have it work correctly since it uses double buffering which the wizard doesn't support.
you have 2 options.. either buy a 2gb one.. or format only half of the card in FAT ...as myrddin said.. this might use only 1 buffer..
if that doesn't work, you can look for a program which blocks clusters and block half of the clusters on the card. that would certainly work but you won't be able to get 4gb out of that card ever again.
i'd go with the first option.. 2gb cards aren't that expensive nowadays.
well guys i bought the sd card for my phone and i research before buying it and it caused work so there must be a way for this to work even if i have to split it in 2 partitions but i am at work now so when i get home i will work on it (good thing i bought that card reader) lol but i will give you guys an update soon i plan to format the card in fat16 all 4gb if that dont work i am going to split the partition in 2 but i would love a single partition but what ever works.
I have a 2gb SD Card...
Hey guys... i have a 2gb kingston card (micro SD with adaptor to miniSD), but i have the exact same problem... my wizard just stopped reading the card! Sometimes it reads, but suddenly wizard stops, i have to make a soft reset and.... the card is gone... i formated it to fat32 and fat... and it still doesn't work... any idea? thanks
nir36 said:
from my experience you can't put ANY 4gb minisd card into the wizard and have it work correctly since it uses double buffering which the wizard doesn't support.
Click to expand...
Click to collapse
Correct-o-mundo.
Another common problem (related more to card readers than just to Wizards) is that the reader contacts (and even the card contacts) can become worn, dirty, or corroded. Try removing the card and battery, and get in there with a VERY bright light, a magnifying glass, and some cotton swabs dipped in isopropyl. Clean the metal contacts on both card and Wizard. Be careful not to soak the chip. Damp, not wet. Soak the chip and you WILL be buying a new one soon.
Let things dry COMPLETELY before trying anything, or you'll be sorry.
sd card is not vissible
hi all i have 1gb memory card it is not visible in all device i tried in a cam mobile and computer can any give me a idea to use