DEAD Q TEK 1010 - MDA, XDA, 1010 Software Upgrading

Hi to all,
I just upgraded Radio Stack on my q tek 1010, now it does not function, there is a blank screen, even on boot loader it shows GSM ERROR.Boot loader version is 5.15. Possibly I did some mistake, but can someone help me, how to bring it back functional.
Thanks in advance

Try searching here in the forum. there are several threads with this topic. Also there are are few solutions for this problem. Sorry to tell you, that inn most cases there was no help other than a service center.... :-(
Stefan

Hi to all
and thanks to stefan, I am sure many smart brains are in this forum. They, no doubt, have salution of this fault.

Hi to all,
Finally i bring back into operation my Qtek 1010, It was so difficult, but it is not difficult now. First I grabbed file for usb connection from qtek rom and installed into qtek through sd card, using card reader and it connected with pc smoothely and nicely. I again upgrade it using 316 upgrade utility and it start working nicely.

Related

RSU 4.21 problem: stuck at boot splash

hi,
i have just downloaded the radio stack from O2 v4.21. I have tried to upgrade through active sync 3.71 it upgraded ok, but when i went to restart the XDA it gets stuck on the boot screen. the one that says test not for resale... and at the bottom right hand corner its says A.30.07 and then locks up.
normally before i tried to upgrade it said A.30.07 the underneath it said 4.20...
anybody know what i need to do to correct it?? i have looked through loads of forum posts and now i'am really confused???
Thanks alot
Zetex :?:
a bit of further info my Bootloader on my xda1 is 5.22
I'am also willing to pay for help i recieve to get my xda up and running again, because without it i really i'am stuck. I don't just use it as i gadget i use for everyday work/pleasure...
Thanks alot
Zetex
can anybody help me????
Hi,
No experts or semi-experts seem to be offering any help. I consider myself a fairly experienced novice so I am not sure how useful (or safe) my advice is. Take care! But here are my observations..........
You say the upgrade went OK? Does this mean you got as far as the message Flash Complete! Press OK to restart your device?
If so, this is encouraging as most of the problems I've located on this forum stopped part way through the upgrade (many at 1%).
Did you follow the instructions accompanying the upgrade to the letter? (ie. kill all running programs, switch off phone etc.)
The 4.21 upgrade is for the PW10A1 model not the PW10B1 (check the back of your xda's case to find out). Not sure how you deal with this one if yours is a PW10B1.
Can you enter bootloader mode? (soft reset with the stylus while holding the power button). If so, this is also good news. Someone with more experience than me could probably tell you what to do next. (Possibly flash a new ROM using the SD card method. Although you upgraded the Radio Stack it may have corrupted or upset your Radio Unit/'ROM'. If you decide to do this, I suggest something based on the v3.17 such as the XDA developers special edition ROM ..... you can always upgrade to WM2003 again later.).
Good Luck!
[/b][/u]
cranny,
Thanks alot for the reply m8, I did try what you have suggested by reloading the 3.17 o2 rom via sd card and now it won't even switch on anymore.
not to worry its gone off to the xda repaire center in Norwich today for repair under warranty.
Thanks for the reply anyway m8
Zetex

Bootloader 5.22 problem please help its important >_>

Ok , here we go , first , hi to all iam new here.
Today i got a xda via ebay and i wanna upgrade to windows mobile 2003 , as i searched the board i got to know that i have to use this sd card method , ok no problem , i also managed to get the rom on my sd card via xdatools... but now comes my problem.
i have bootloader 5.22 and it seems that bootloader 5.22 dont recognizes my rom. SO is there any way to downgrade to 5.15 coz i saw others who said its impossible 0,o
is there anyway to upgrade 0_o pls help me ^^
Take a look at:
http://forum.xda-developers.com/viewtopic.php?t=6581&highlight=downgrade+bootloader
http://forum.xda-developers.com/viewtopic.php?t=2068&highlight=downgrade+bootloader
HTH
Stefan
Well thanx ,
But i solved the problem myself using the german mda with ppc 2003 from my dad , so i saved the devices rom to sd and then used it on the xda which worked fine ^^

I need help restoring my windows mobile 2003 software

:roll:
Hi I have a big problem and i need all the help i can get
I have an XDA IIi but i accidently deleted all the data on it
the opertating system is gone the screen is only showing me Serial 1.0
and when i connect to my pc only shows USB 2.0
I would like to know if somebody can help me out with this and tell me how to restore the software to my device, i have a backup copy on my SD card, but i don't know how to used
Please help me
thanks
[/b]
have to reflash it
how did it happen?
did you try puting any rom version in it or what?
more info is needed
hey
I was trying to upgrade the radio version of the phone, but the version i was installing was not desgined for the XDAIIi , so, instead of upgrading, it deleted of the rom of the device and now the operating system is gone
the only thing i still have is the backup copy that i made defore the upgrade
i don't know if there is a way to use that backup copy in order to restore the system
thanks
Recommendation
It is propably that the system ROM was erased during upgrade and the upgrade wasn't successfull. Try to download the Diamond 1.2 WM2003se(my recommendation) ROM images package(somewhere available at this forums(Himalaya Upgrade)) and aferwards to flash your device with these files. If u want,u can try also the WM05 system.
He said his device is an Xda IIi not the old II.. Well you can reinstall back ur old ROM, no worries.. Download from my-xda.com..
i or not i
I thing there's no matter if is it IIi or simple II. Or not?
How do I fash my device in order to install diamond 1.2?
I also was looking an upgrade for the XDA IIi but now there are not offering any updates, I have tried to install the upgrades for the XDAII but it gives me an errror telling me that the ROM version is different and it cannot be installed
...
If you mean the Country ID Error while attempting to flash the WM05 system,there's a problem of this OS. 2003se is without problem(for me). Simply download the Diamond ROM from this topic:
http://forum.xda-developers.com/viewtopic.php?t=18287
or directly:
http://forum.xda-developers.com/download.php?id=3739
This contains 4 files(maybe more,but these are important).
-HimaUpgradeUt.exe
-ms_.nbf (Extended ROM image)
-nk.nbf (System Image)
-Radio_.nbf (Radio stack)
Start the bootloader(probably you are there),put the Hima to cradle,Windows at your computer detects your device and then extract the downloaded file into one folder and run HimaUpgradeUt.exe
This utility is writing what you should do.
As I have readed that the WM05 OS is a little bit buggy(some compatibility problems etc..) at this time to use in Hima. Therefore I am using the 2003se.
Thanks a lot!
Hey guys,
I just downloaded the XDA IIi ROM version from the O2 website
My device is back to normal. I coudn't do it without all of you guys.
Thanks a lot specially to you jamil_mhmd for providing me the address
Sincerely
Jorge :wink:
You're welcome
Nice to help you.
Re: i or not i
TomasNM said:
I thing there's no matter if is it IIi or simple II. Or not?
Click to expand...
Click to collapse
Of course it does matter.. Remember that the II and IIi is now a really different device even though both looks identical.. For example, u said he can upgrade to WM2005 (or ROMs that was meant only for Xda II), but of course this can't be done, this is bcos the difference in hardware specs, 4 example IIi has 1.3 MP cam (II = 0.3MP), 128MB RAM, 128MB ROM (II=128MB RAM, 64MB ROM) and so on..
JorgeGZC, I'm glad to be of help to you.. :wink:
Oh sorry.
I didn't know. I'll be well advised.
İ am a mda2 user. İve bought my device from Germany and after that i changed its ROM to an english one using a rom editor to change its country id .. This encouredged a close friend of mine and he bought a O2 XDA2i. And since both me and my friend have no idea about German language we immediately tried to convert it to an english ROM.
And using a wrong ROM (sinmerged 2003 se for himalaya) i killed his machine. It now only writes serial or usb (when connected to cradle). Someone told us that if we flash it with a original German ROM it can work again. But there is no German ROM downloadable . And even if we find a German Rom and install it , it wont solve our language problem. I am a dentist and i even cannot believe how much i've learned browsing these forums
If you can help me i will be very happy!
note : in the ftp server there is rom named german rom for xda2i.. But its a lie. its in english
The same?
That looks like the same problem as at the top of this topic. Just read all this posts once again and you'll get the right way to solve your problem. Hope that helps.
I also have the same problem. I tried to install the wrong upgrade. I've downloaded the new one but i keep getting a connection problem message because activesync can't find the XDA. Help please!!!!
...
When you are in bootloader then ActiveSync will not find the device to synchronise with(cause the WMOS is not running and therefore is any synchronisation disabled). When you put into the cradle,the computer should find new device(Microsoft USB Sync). Then is the device connected and ready to update.

Help Needed....Incorrect Vendor ID

Hi guys...I know there have been numerous reports of this kind, but I can't seem to find the answer.
I don't have this problem myself, but another person does and I thought I'd ask Olipro and the rest of the community for some help and clarification. Also hoping this answer can help anyone else who has this issue.
OK, Someone tried to flash WM6 before using the Unlocker. I know...don't say it. Anyway they now have the black screen of death and the tri-coloured bootloader screen, but are still unable to flash WM6 and obviously cannot use the unlocker until they have an O/S to sync with.
Has anybody encountered this and received incorrect vendor ID and found a way out of this scenario? They have an Austrian T-Mobile Ameo UK, so they can't even use the T-Mob 005 ROM for the UK Ameo (which doesn't require the unlocking of ones device).
Any clues peeps? It would really help a fellow owner out. Cheers for any input. Remember even if you said it before and don't want to repeat yourself again, please just cpoy & paste the answer here so it can act as part of the wiki for future incidents of this nature.
Thanks friends.
I got part of the experience. So I will tell what happen to mine AMEO.
due to some software conflict, my WM6 OS got kill. I was stuck in the tri-colour screen as well.
Since my unit was unlocked before, so refreshing (any) ROM solved my problem. (refreshing the ROM doesn't required activesyn running on yr PPC.)
If can't reflash yr ROM due to vendor_id error, I think the best way is to get the origin WM5 ROM (read it out from another same model) and flash it back.
after getting yr origin OS, then u can proceed unlocker and WM6 upgrade.
Hope this can help.
royalmail said:
I got part of the experience. So I will tell what happen to mine AMEO.
due to some software conflict, my WM6 OS got kill. I was stuck in the tri-colour screen as well.
Since my unit was unlocked before, so refreshing (any) ROM solved my problem. (refreshing the ROM doesn't required activesyn running on yr PPC.)
If can't reflash yr ROM due to vendor_id error, I think the best way is to get the origin WM5 ROM (read it out from another same model) and flash it back.
after getting yr origin OS, then u can proceed unlocker and WM6 upgrade.
Hope this can help.
Click to expand...
Click to collapse
Thanks Royalmail. I'll pass it on.

Universal qtek 9000 Problem. What im doing wrong?

Hello good friends,
Im from Portugal and i have a qtek 9000 since 2006. In the last days i decide to improve my universal performance...
i try everything to update my qtek since the software is very old ( windows mobile 5 2005)
After a lot of hours searching in this forum, i download a lot of software from all the posible tutorials.
From evk to updatev2, kitchen, etc.
With the kitchen in the last part i always get an error of the extended rom.
With the update, it only appear the nk file.
I try to download one of the radio files, but without sucess and i donw know what to choose
I dont know what to do more, since i use the romupgradeut, but now the qtek only start in the first image where tells the version of rom and hang up, freeze, dont do the all restar.
The only thing that work it is the soft and hard reset. With the bootloader appears usb when connected and serial disconected.
Can you guys help me find a full package including the last windows mobile, the last radio definitions, the extended rom and all i need to upgrade my qtek.
I really dont know what to do more, even the qtek logo image not appear any more.
Sorry for all this questions, but i see in this forum you are my only hope.
Please help me.
Thanks a lot
jus to help us..
could you post the error message?
I try to upgrade the rom with a software download from qtek.nl, but i still dont have good news
Can anyone help me?
I dont know what to do anymore
cybervtec said:
I try to upgrade the rom with a software download from qtek.nl, but i still dont have good news
Click to expand...
Click to collapse
did you read and answer Simon request ?
what are the error message ?
I currently have a qtek9000, and i made my first upgrade late 2006.
I was using XP sp2, activesync, and a software called uniextROM...
Later, I have tried using vista and win7, both requiered installation of USB Mobile Modem Driver and disabling activesync or mobilesync.
so be more precise when you post you issue.
Welcome to forums
have a deep read in my signature link
Most likely you´ll be able to solve the problem.
If not please give us more detailed info so we can help
Read, Search, Respect and Enjoy!
Simon_WM said:
jus to help us..
could you post the error message?
Click to expand...
Click to collapse
Hi Guys,
How can i read the errors? Where can i find it?
Sorry for all the noob questions.
All i can see in the universal is a dead phone without any kind of signal when turned on
cybervtec said:
Hi Guys,
How can i read the errors? Where can i find it?
Sorry for all the noob questions.
All i can see in the universal is a dead phone without any kind of signal when turned on
Click to expand...
Click to collapse
Can you get into the bootloader?
Power + light + Softrest button ?
then connect to your pc and flash
Simon_WM said:
Can you get into the bootloader?
Power + light + Softrest button ?
then connect to your pc and flash
Click to expand...
Click to collapse
Hello Simon,
Yes, i can get in the bootloader. When i connect appears usb.
The problem is i dont know what files i should load.
Can you give me the links to the files i should use. Sorry for the trouble.

Categories

Resources