Related
Not quite sure what the issue is with this one. Back in the beginning of the year my XDA II fell from waist height when the carry case snap popped open (notebook bag brush across the front catching on the flap). The only noticeable problem after that was that the power button no longer works, so I have to power it on by pressing the phone or address book buttons etc.
About a month and a half after that incident the phone suddenly just stopped getting signal. I was using the standard shipping firmware with a few apps. Soft reset, hard reset both failed to fix the issue, the phone simply will not pick up the network. Interestingly enough if I play with the phone settings and go through the process of manually selecting a network the phone WILL pick up available networks in the area (this kills my idea that the GSM radio failed altogether). For now I've had to switch back to a junk phone as I've been unable to figure this one out. Anyone have any ideas on this one? I'm using T-Mobile for a service provider and I'm based out of California.
Also, does anyone know of a place that can do diagnostic/repairs here in the U.S.? So far my searches have come up empty.
Thanks in advance.
Give this a try:
Reflash the phone with any version of ROM and it should start working fine again. I think the problem is that you're radio firmware somehow got corrupt.
Ok, guess I'll have to give it a try. I've been avoiding trying the slightly riskier stuff as I got this thing via an independant third party, so warranty/support are iffy.
Is there a general release ROM that I should be looking for (using T-Mo in U.S.)? Or should I look to cooking my own (which I'd rather not)?
You can try upgrading the ROM with the same branded one. That shouldn't void the warranty.
I.e. If you've got an O2 device, get the new O2 ROM
Reflashing
I have had a simular problem with hard locking. Finally my phone quit working all together. I went into boot loader mode and flashed it. It's like having a new phone again. So yeah.. I think the ROM's can get corrupt.
Brandon
NeoCole: Looks like you are using T-Mo in the U.S. Mind if I asked what you flashed yours with? Did you use a specific ROM, Radio Stack version etc.?
I'm running an unlocked i-mate (contradictory to my subj title, I know).
Flash it with the T-mobile 1.72 ROM
ROM Version
Well.. I flashed it with the IMATE 1.72 ROM and used most of it's extended ROM. I used the battery Meeter from the Qtek extended rom. I built most of my extended ROM Myself.
I look at T-Mobile's Beta 1.72 ROM like I look at Windows ME. Both should have never happend. I can't count how many times I had a hard reset with the T-Mobile ROM. I'm not sure if it was a combination of the programs I was useing or not. I saw a post that said SBP was possibly causing the problem. So I quit using SBP products. Later I still had to HARD RESET from time to time. Now that I'm running differently, My device has never been so smooth.
Let me know if this helps,
Brandon
Looks like I'm pretty much screwed. Without a working power button I can't do a hard reset into bootloader mode. When I try using a utility app that allows me to do a hard reset I can't hold down the jog dial at the same time. Good times.
*edit: yeah, that would be 'can't' hold down the jog dial.
You don't need to boot into the bootload to perform an upgrade... the upgrade software takes care of everything for you (except the hard reset at the end)
All you need to do is sync through Activesync and then run the upgrade program.
I would (and have!) flash the imate 1.72 ROM. It is very stable for me and HAS improved the battery life of my imate.
As stated above, just start the flash process and it will put the device into bootloader mode and perform the flash. It will need a HR at the end, but since your power button is not working, maybe you could remove the battery, slide the red slide/switch back into place for a few seconds as if the battery were there, then slide it back, put in the battery, slide it back into place and press one of the puttons to turn it on.
Hey . . . it might just work!
imate 1.72 ROM did the trick. After I actually READ all the posts regarding the ROM I realized it came with an installer and got that done. So far so good. Now if I could only find my missing tomtom 3 cd key that went MIA during my last move
Hey, that's fabulous! Welcome back to the world of convergence.
Please help, I am really desparate at this point. I just got today Qtek S200 in French. After reading most of the messages in this forum, I felt comfortable that I could change the language from French to English. First I installed Active Sync 4.1 in English. Then, I downloaded and ran Lokwiz.bat to unlock the CID. Next i ran CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe (ROM version 2 something) to change the ROM (again i downloaded the file from this site). During the installation everything seemed to go on fine with % sign increasing with time. Then, at the end, it said "Congratulations...." The sign went away on the computer and the PDA went blank. So, I proudly thought that everything was fine. THen the screen started blinking on and off and the red and blue lights of the phone started blinking as well.
Now, no matter what I do nothing works (e.g. hard and soft reset, etc.). Other than taking out the baterry nothing helps. Also, the computer is not recognizing that the phone is connected either.
PLEASE LET ME KNOW if you have seen something like this. I am afraid that i burned my PDA irreparably. Thanks a lot.
Ekat said:
Please help, I am really desparate at this point. I just got today Qtek S200 in French. After reading most of the messages in this forum, I felt comfortable that I could change the language from French to English. First I installed Active Sync 4.1 in English. Then, I downloaded and ran Lokwiz.bat to unlock the CID. Next i ran CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe (ROM version 2 something) to change the ROM (again i downloaded the file from this site). During the installation everything seemed to go on fine with % sign increasing with time. Then, at the end, it said "Congratulations...." The sign went away on the computer and the PDA went blank. So, I proudly thought that everything was fine. THen the screen started blinking on and off and the red and blue lights of the phone started blinking as well.
Now, no matter what I do nothing works (e.g. hard and soft reset, etc.). Other than taking out the baterry nothing helps. Also, the computer is not recognizing that the phone is connected either.
PLEASE LET ME KNOW if you have seen something like this. I am afraid that i burned my PDA irreparably. Thanks a lot.
Click to expand...
Click to collapse
push "standbye" and "cam" button and than the reset
to show the colordisplay
and than put the usb in and flash another ROM
that´s all...
rodigezstyle said:
Ekat said:
Please help, I am really desparate at this point. I just got today Qtek S200 in French. After reading most of the messages in this forum, I felt comfortable that I could change the language from French to English. First I installed Active Sync 4.1 in English. Then, I downloaded and ran Lokwiz.bat to unlock the CID. Next i ran CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe (ROM version 2 something) to change the ROM (again i downloaded the file from this site). During the installation everything seemed to go on fine with % sign increasing with time. Then, at the end, it said "Congratulations...." The sign went away on the computer and the PDA went blank. So, I proudly thought that everything was fine. THen the screen started blinking on and off and the red and blue lights of the phone started blinking as well. Now, no matter what I do nothing works (e.g. hard and soft reset, etc.). Other than taking out the baterry nothing helps. Also, the computer is not recognizing that the phone is connected either.
PLEASE LET ME KNOW if you have seen something like this. I am afraid that i burned my PDA irreparably. Thanks a lot.
Click to expand...
Click to collapse
push "standbye" and "cam" button and than the reset
to show the colordisplay
and than put the usb in and flash another ROM
that´s all...
Click to expand...
Click to collapse
Thank you so much for replying to my plea. I was so hopeful but unfortunately what you suggested did not work. I pressed all these three things together and held it down but nothing happens, no color display .
Am I doing something wrong or do you have any other suggestions?
Hi, Unfortunately you have flashed Wizard instead of Prophet ROM. I did that when I first got my Dopod and could not find a way to fix it. After many desperate tries, I finally send it for service. I was fortunate that they replace the entire mother board (with different serial number) without charge. Looks like the wizard ROM kills the prophet. If someone or you can figure out how to recover from this without swapping the device, please let us know - I think there are many who would benefit from the experience.
My lesson learnt - only stick to prophet ROM for prophet device!!
I called up support and they told me that it is possible to do it if one has a software (does not need a special machine or anything), they just can't email me the software.
Any suggestions?
http://forum.xda-developers.com/viewtopic.php?t=41517
Hi there.
First I must apologize for my bad english.
But this isn't my only problem. Beside new Samsung i600 I have my very-old-but-still-good MDA Compact, also known as HTC Magician. I'm using it as GPS navigation with external Bluetooth GPS reciever and everything was fine until I've tried install new iGo 8, so called NavN'Go software. Installation ended without problems and app was working. For a while. After something about 5 sec of navigation my Magician turned off. Not restart, totally off. OK, I've tried to turn it on. Everything what I'm getting is bootloader and - sometimes - 1sec of homescreen. After that, Magician fall to sleep.
Of course I've tried reflashing ROM, without success. Same problem with same 1sec of "Welcome in Windows Mobile 2003 SE" or what is first screen after reflashing.
I'm asking for help or advice, never happend to my Magician before. So I've search in this forum but nothing equal to my problem.
And little switch under battery cover isn't solution, soldering machine more than 2 years ago has done this HTC joke for me.
Lot of thanks for any ideas, I never leave my Magician, we are in love forever but working one is better than dead one, isn't?
ROM 5.60.00 WWE
Radio 1.15.00
Protocol 1337.45
After Helmis WM6.0 upgrade everything works fine, apart the Phone mode works only after a soft reset. Turning off in the Comm Manager works, but cannot be switched on again.
BT works perfect.
Upgrade from Radio 1.13.00 to 1.15.00 had no effect .
Any suggestions.
Thank you.
Lunart said:
ROM 5.60.00 WWE
Radio 1.15.00
Protocol 1337.45
After Helmis WM6.0 upgrade everything works fine, apart the Phone mode works only after a soft reset. Turning off in the Comm Manager works, but cannot be switched on again.
BT works perfect.
Upgrade from Radio 1.13.00 to 1.15.00 had no effect .
Any suggestions.
Thank you.
Click to expand...
Click to collapse
Did you follow all procedures. Specially the Clean Hive (aka)No Yes Yes ? Had you tried other ROM's? Some if not all ROMS for BA, after flash you need to turn phone ON. But from what I understand, yours turns on, then can turn off, but can't ON again. Ummm I can also suggest you to read the full thread for Helmi's ROM and see if others have had that problem and if they've found a solution.
markanthonypr said:
Did you follow all procedures. Specially the Clean Hive (aka)No Yes Yes ? Had you tried other ROM's? Some if not all ROMS for BA, after flash you need to turn phone ON. But from what I understand, yours turns on, then can turn off, but can't ON again. Ummm I can also suggest you to read the full thread for Helmi's ROM and see if others have had that problem and if they've found a solution.
Click to expand...
Click to collapse
Hey Markanthony! Happy New Year!!
@Lunart,
You may want to upgrade to a later rom since that was a bug (which was later resolved) in Helmi's WM6.0 roms. The phone cannot get into or out of flight mode (I can't remember which one)...
Try sun_dream's or xplode's roms since they no longer have any of these bugs. Hope this helps.
Hi Markanthonypr , Egzthunder1 ,
thank you for your suggestions. First I tried to re-install Helmis WM6 and applied the "clean hive" no,yes,yes. This did not work.
And then I flashed sun_dreams Rom and everything is 100 %.
Thank you both. Best wishes from Germany.
egzthunder1 said:
Hey Markanthony! Happy New Year!!
Click to expand...
Click to collapse
Hello my friend, Happy New Year to you too Good to read you mate!
Lunart said:
Hi Markanthonypr , Egzthunder1 ,
thank you for your suggestions. First I tried to re-install Helmis WM6 and applied the "clean hive" no,yes,yes. This did not work.
And then I flashed sun_dreams Rom and everything is 100 %.
Thank you both. Best wishes from Germany.
Click to expand...
Click to collapse
Glad you got it working. Enjoy!! This is a great phone. I'm shopping for another one for my girlfriend
Edit: Hey Egz, remember I mentioned about my Siemens SX66 now showing PH20B instead of PH20B1? Well guess what... As I was seeing other phones on E-Bay, one folk showed an enlarged pic of his phone w/o battery, and I noticed it said Ph20B <<<But.. Its a Siemens(NO CAM).... soooo I removed battery on my phone and guess? It also says PH20B... So I'm very confused. I would have swore that I had seen on the phone info that it was a PH20B1(As shown on Device Info/Identity) and have also read everywhere on here about PH20B1's being without camera(as mine is), so, which is my correct phone? LOL ok, I know what the Back Label says! PH20B! But.. It is confusing... Any Lights?
markanthonypr said:
Hello my friend, Happy New Year to you too Good to read you mate!
Glad you got it working. Enjoy!! This is a great phone. I'm shopping for another one for my girlfriend
Edit: Hey Egz, remember I mentioned about my Siemens SX66 now showing PH20B instead of PH20B1? Well guess what... As I was seeing other phones on E-Bay, one folk showed an enlarged pic of his phone w/o battery, and I noticed it said Ph20B <<<But.. Its a Siemens(NO CAM).... soooo I removed battery on my phone and guess? It also says PH20B... So I'm very confused. I would have swore that I had seen on the phone info that it was a PH20B1(As shown on Device Info/Identity) and have also read everywhere on here about PH20B1's being without camera(as mine is), so, which is my correct phone? LOL ok, I know what the Back Label says! PH20B! But.. It is confusing... Any Lights?
Click to expand...
Click to collapse
Weird... if you got your BA second hand, there is a chance that the previous owner exchanged the case for a PH20B either to make it look nicer or maybe because he messed it up along with the camera, which he/she might have messed up as well (too farfetched of a theory if you ask me, but it is possible)... God only knows!
Another explanation is that they put the wrong board on the phone when they made it... could happen (far more likely to happen than a guy completely modding his BA )
Anyway... weird indeed.
hi i have exactly the same problem. but with sundreams rom
HTC-BA_5.2.20758WWE_v3.02__25M_PP-16M_RAMdisk
i am not really sure but i think i can't really controll anything via comm manager except for switching the phone off (on does not work obviously...), i definitly can not turn wi-fi and bt on using the comm manager. turning it off i did not test yet (i have activated / deactivated wi-fi and bt through the options in "settings" until now)
any ideas?
greetz fleity
Well... first and foremost, Lunart's issue has nothing to do with Wifi or BT, it was a problem with "Flight Mode" option in the Comm Manager.
Your issue is a completely different one. It is a bug that has been widely talked about in this forum. There are probably close to 100 posts (if not more with the answer for your question). I feel like being a nice guy though, so I will save you the search time.
The problem with CommManager was introduced somewhere along the porting of WM5 (aka Magneto) back in the day. The problem consists in the comm manager not being able to load the necessary drivers for wifi from its interface (don't ask me why, I have no clue). The workaround for this is relatively simple. [highlight]You have to do this after every soft reset, so please keep it in mind.[\highlight]
1. In the CommManager, go to Settings > Wireless Lan
2. Once there, you will see the option "Wireless LAN OFF. Turn on WLAN". Click on it. More than likely, your device will try to establish a connection and fail (sometimes it does connect though). This is fine since your objective was not to establish a connection at this point. You are only trying to load the drivers.
3. Get out of the settings and go back to Comm Manager and click on the WLAN icon and Voila!!!! You will now be able to toggle Wifi on and off via CommManager.
BT should work without problems though. If you are still having problems (and considering the strange behavior in CommManager that you are describing), you may want to consider a Hard Reset. One other alternative for things not working the way they should could be that you did not completely clean the Hive after flashing the rom.
Hopefully this will help you out.
hm thx but that is unfortunatly not directly my problem. i don't really care if i can control wifi and bt with the comm manager because for them i have other possibilities (speaking of the settings dialog etc.). i just thought it would be usefull to know.
the real issue is the phone i am able to turn it off via comm manager but not on again (and with no other button, dialog whatever too).
i noticed it yesterday when i was visiting a friend, at his house i have absolutly no signal at all, so i thought "hey why not turn the phone off, lets see how much battery that saves me" and later as i tried to turn it on again my only chance was a soft reset.
if you can tell me just some way to switch the phone on and off i don't need the comm manager anyway
fleity said:
hm thx but that is unfortunatly not directly my problem. i don't really care if i can control wifi and bt with the comm manager because for them i have other possibilities (speaking of the settings dialog etc.). i just thought it would be usefull to know.
the real issue is the phone i am able to turn it off via comm manager but not on again (and with no other button, dialog whatever too).
i noticed it yesterday when i was visiting a friend, at his house i have absolutly no signal at all, so i thought "hey why not turn the phone off, lets see how much battery that saves me" and later as i tried to turn it on again my only chance was a soft reset.
if you can tell me just some way to switch the phone on and off i don't need the comm manager anyway
Click to expand...
Click to collapse
Like I said, it could be an installation problem (the hive not being properly cleaned out and so on). A hard reset should take care of the problem. I have the same rom as you do (only without the pagepool) and have not experienced this problem at all. Give it a try and hopefully it will solve your issue.
ok i will do that thx already
I have a Hermes (Orange SPV 3100 but unlocked). The phone has stopped working but everything else is fine.
I've tried putting other sim cards into it, cleaned all the sim contacts etc with no success at all. As far as it's concerned, there is no valid connection. Phone and data connections don't work. All the Windows settings and programs run fine, it's just the phone that doesn't so I have a pda without a phone! I wasn't trying to flash a rom - the op system is all as original except for the unlock.
I don't think it's worth enough to pay for a professional repair so any suggestions for tracing and curing the problem and hints as to whether its likely to be a faulty connection, faulty parts or software problem?
Thanks.
I have the exact same phone, and similar problem. The difference is my phone is not completely unusable, it sometimes works for a while and sometimes doesnt.
I have just - 10 mins ago - flashed a new radio rom to see if it helps and so far (10 minutes!), so good. But I will need to leave it for a couple of days to see if it works properly.
Is there an "X" beside the signal icon? Also have you checked the Comm Manager and disable the phone and enable it again?
Ah well I didnt need to leave it for a couple of days, its not working again even with new radio rom.
Ive tried new o/s, new bootloader and new radio but still the same problem, nothing else to try really ?
(btw: Mine usually has an exclaimation mark next to signal strength.)
Carthief When did the problem first start occurring? Did you flash a radio/OS ROM and it started to happen, or did it just happen out of the blue?
Sorry I did not see this post...http://forum.xda-developers.com/showthread.php?t=562486
I don't know dude. Maybe one of the senior members can help out.
Shawn80 said:
Is there an "X" beside the signal icon? Also have you checked the Comm Manager and disable the phone and enable it again?
Click to expand...
Click to collapse
I will check tomorrow. I am using a different phone at the moment and have left the Hermes at the office.
Hi Shawn, yeah that post covers when my phones problem started - I hadnt flashed anything recently when it started messing up.
I've tried tonight;
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
Problem 5:
METHOD 1
But I didn't flash the patched radio.
Phone is working at the moment... I'll update if it is still working or not tomorrow, if its still working maybe Batxda could try it out as well
--------------
Update:
--------------
Phone worked all night, and this morning, but froze up this afternoon and needed rebooting. It's currently working ... but probably not for long! My battery is running out very fast as well.
Shawn80 said:
Is there an "X" beside the signal icon? Also have you checked the Comm Manager and disable the phone and enable it again?
Click to expand...
Click to collapse
Hi again. Yes, there is an "x" beside the signal icon (normally meaning that phone is turned off) and also beside the connectivity icon (two horiz arrows and a "x" meaning no active connection). Also, I've just noticed that both of those icons no longer respond to stylus taps. All the other icons do.
I've tried turning the phone on via Setup > Connections > Comms and Setup > Personal > phone. Neither work, in fact, they do not respond at all.
I haven't tried the cure that Carthief tried but then, I've never flashed any roms on this phone either. I am apprehensive about that because I haven't done it before so, if that's the solution, I would need to find a free evening and do lots of reading.
BTW, the unlocking was done ages ago professionally, not by me.
Any ideas?
Thanks.
Batxda said:
Hi again. Yes, there is an "x" beside the signal icon (normally meaning that phone is turned off) and also beside the connectivity icon (two horiz arrows and a "x" meaning no active connection). Also, I've just noticed that both of those icons no longer respond to stylus taps. All the other icons do.
I've tried turning the phone on via Setup > Connections > Comms and Setup > Personal > phone. Neither work, in fact, they do not respond at all.
I haven't tried the cure that Carthief tried but then, I've never flashed any roms on this phone either. I am apprehensive about that because I haven't done it before so, if that's the solution, I would need to find a free evening and do lots of reading.
BTW, the unlocking was done ages ago professionally, not by me.
Any ideas?
Thanks.
Click to expand...
Click to collapse
Maybe I missed it but I did not see any mention of your doing a Hard Reset. (I assume you have tried soft resets) In general if the problem persists after this it rules out most software issues. I also think it's worth a try because of your comment about the icon being unresponsive.
Mike
Mike
I had done a hard reset but, just to be sure, I've just done it again. After the first it locked up at the password screen so I did a few more. Next, I let the Orange config run through. With the third, I removed the battery before Orange it did its thing. Both the same - no active phone but no lock-up either.
Icons on top bar still not active and x's against them.
When I go to settings > Personal > Comms, the phone icon is highlighted and appears to be "on" (no "x") but the top bar icons still show that it isn't. When the comms phone icon is clicked, the cross appears and the phone is, presumably, turned off and can't be turned on again.
When I go to settings > Personal > Phone, it says that the phone is off, would I like to turn it on. Click yes but it doesn't work.
BTW, I'm using an O2 sim card which works perfectly in a NIKI (touch dual).
I hope this is a software not hardware problem. Is there any point in flashing a new radio or complete windows rom? If so, which one would you recommend (it's a minefield for one of little brain)
Many thanks.
B
I did think you might already have tried a hard reset. In general that tends to point towards hardware, BUT corruption of the ROMs can occur. Unfortunately that is not my area of expertise. Hopefully someone will recommend something here. You could always look on http://www.mrvanx.org/thg/ making sure you have Hardspl installed.
Mike
Hi all, my phone is still not working completely but it does seem to be staying alive for longer periods now.
I have just downloaded the latest (from Oct. 2007) software upgrade from Orange for the Hermes - I think it is windows mobile 5, not sure yet. I cant install it tonight but Im going to try that tommorow.
I downloaded the Orange update but it wouldn't load on my phone. all I got was an error message which said it was the wrong rom for the phone. I don't know whether that's because I've had it unlocked or maybe my rom is newer than the update. anyway, I'm no further forward.
I've just noticed that, in Settings > Device Information, it is blank against the radio version and the Protocol version and that there is no IMEI listed either. I guess that means the radio is corrupted so I will try installing a new one. It is op version 14.123.1.614 and ROM version 1.23.61.4. Which radio is recommended.
What does the missing IMEI number mean or is that also connected with the missing radio?
B
Hi Batxda, I dont know which radio to recommend, mine is Radio version: 1.47.30.10 and ROM version: 3.54.255.3
My phone has now been working for over 24hrs, battery has stayed charged as well... so I haven't installed the Orange rom yet.
I bought a new phone having pretty much given up on this one... and now it seems to be working again!
Nope. Not working. Ran for over 48hrs but locked/froze up today with calls going straight to answerphone, battery drained from 70% to 20% in about two hours as well!
My last attempt is going to be running the phone with no memory card in, and no sim card with phone disabled. Will report back.
Have you had any luck Batxda ?
Radio flashes all lock up - help please
carthief said:
Nope. Not working. ...............
Have you had any luck Batxda ?
Click to expand...
Click to collapse
Sorry to hear that. I've had different but similarly unsuccessful times. I hope your experiment goes well.
I flashed with HardSPL (SPL-2.10.Olipro) then tried to flash a Radio.
1st I tried v 1.11.00.00 running from the PC. It froze so I had to unplug it. That messed everything up and I ended up with it stuck on the bootloader screen (Type 2a) so I used mtty and found that command "set 16 0" worked so I could return to WM5.
2nd I tried to flash radio v 1.47.00.10 from the SD card. It started OK, got to about 20% and stopped. That was at 11:15. Its now 13:30, 2.25 hours later and it hasn't moved in that time. I am going to have to stop it but I'm sure it will end up corrupted again.
H E L P anybody, how can I flash a radio to this damned thing?
BTW, it is a Hermes 100.
B
Batxda when I reflashed a new radio I just followed the guide here:
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=18&Itemid=26
It sounds like you've gone through the same procedure as me so you've probably already followed that guide...
I don't know what to suggest, but if it was me, and the radio wouldn't flash, I would (being a bit dim ) try it a few more times until I was exhausted...
I've just rebooted mine to see if I could provoke it to do anything with no sim/memory cards in. It gets to the password entry screen and tells me I've entered the wrong password but I know its the right password !! Does anyone know where/how these phones store the password ?
carthief said:
Batxda when I reflashed a new radio I just followed the guide here:
http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=18&Itemid=26
It sounds like you've gone through the same procedure as me so you've probably already followed that guide...
I don't know what to suggest, but if it was me, and the radio wouldn't flash, I would (being a bit dim ) try it a few more times until I was exhausted...
I've just rebooted mine to see if I could provoke it to do anything with no sim/memory cards in. It gets to the password entry screen and tells me I've entered the wrong password but I know its the right password !! Does anyone know where/how these phones store the password ?
Click to expand...
Click to collapse
I have a AT&T 8525 Hermes that was having No GSM issues.
I'm not sure if both of you seen the No GSM message when booting the phone (when it was bootable) & if you did, here's what I did to get the phone working again.
I removed the battery & pressed hard against the back stainless steel plate especially around the area near the battery contacts. It worked for mine & the No GSM issue would go away. If it happened again, then I repeat the same procedure & it works again.
My conclusion is that the GSM chip has broken or loose contacts with the motherboard so as long as the contacts is good, that keeps the radio working. BTW, this phone was dropped before & after that, this issue started happening.
Lastly, I'm not sure if your issue is really with the password...that's just a symptom of something else that is wrong with the system...not sure if it's entirely software or perhaps hardware or combination of both.
konker said:
I have a AT&T 8525 Hermes that was having No GSM issues.
I'm not sure if both of you seen the No GSM message when booting the phone (when it was bootable) ...
Click to expand...
Click to collapse
No, I haven't seen that message.
Since the last post, I've tried to flash various radio roms, two WM6 roms and what XDA says is the original WM5 Orange SVP M3100 rom for my phone (v slightly different version number though). All of them hang at around 11% or give an error message. I've ended up with a Dopod start screen (from one of the WM6 attempts) and a funny mixture of colours but I can still start Windows so I've got a pda with no phone access.
Taking your message on board, I'm starting to think that there is a hardware fault preventing the radio from being recognised. That is unless there is something fundamental that, being a n00b at this, I'm not doing. I've put Hard SPL on the phone, flashed roms and failed, reset it with MTTY (set 16 0) and used a variety of radio and main roms. Is there anything else I should have done?
I'm about to give up and see what it's value is and then see if I can get a hardware repair (if it's worth it). Otherwise, I've heard that some fetes have a throw the mobile competition ......... !!!!!!
B