Related
My phone accidentally fell on the carpet from my desk while it was charging and the charging socket broke and now is loosely stuck inside the charging hole. USB as well as charging aren't functioning. I was about to open it up with the help of the wizard disassembling manual but I don't know what I need to do afterwards. I know I will be sautering but will it be just that simple or will I have to be careful how and what I sauter? Any help on this matter is greatly appreciated! I would contact T-Mobile but my warranty has already expired.
Well, the USB port falling out/in is pretty common problem that is covered under warranty (as long as you haven't "dropped" the device).
Post warranty replacement is $100, still a pretty good deal. If you clobber the device when you take it apart, I suspect you may be out of luck on the $100 out of warranty replacement.
I suggest Pocketpc Techs..costs 60 dollars to fix it. If not then just get a seperate battery charger and bluetooth usb to sync. Goodluck!
Thanks
Thanks everyone for getting back to me. Ever since the MDA broke, life has been a mess. Schedules are all messed up and I forget my appointments, hence the late reply to your comments. Clems, you said there is an external battery charger that can be purchased? Where can I find this charger? I will look up the procedures for sync the MDA with bluetooth.
Even if you decide to just use an external charger and bluetooth sync, you should try to remove that loose usb plug. If its rattling around in there loose, who knows what components or solder pads it might touch and short out. You might endup totally killing your phone
I bought a Cradle for my TyTn II from Brando Web site. they are located in Hong Kong. I have been dealing with them since 2000.
they usually provide good service.
However this charger did not work, AC or USB part. I emailed them and they were kind to send me a replacement in 1 week.
Again still not charging or connecting to my computer. I skipped the cradle and tried the USB cable only still not working.
I emailed them back and they want me to ship both units back to them. I understand that there is a problem with certain connections charging or connecting with Kaiser an I tried to tell them that; I don't think they believe me.
Do Not Order this Cradle since it will not work !!
http://mobile.brando.com.hk/prod_detail.php?prod_id=03012&dept_id=039&cat_id=0996
Uh thanks for the warning, I almost bought the same thing.
mdshahed said:
However this charger did not work, AC or USB part. I emailed them and they were kind to send me a replacement in 1 week.
Again still not charging or connecting to my computer. I skipped the cradle and tried the USB cable only still not working.
Click to expand...
Click to collapse
Stupid question, but does your Kaiser connect to your computer with ANY USB cable? I'm using a cradle (from Talkietech.com) which looks identical to that one with no problems at all. Works with both a USB connection (though I re-used an existing cable) and just with the wall power plug.
If the provided USB cable isn't working, try one which you know works....
Richard
It's not only the USB cable but also the charger included.
any other USB cable works on my computer though.
Brando contacted me again yesterday they will send me a third unit. I will post once I get the third unit.
cheers.
Also returned one of these for same reason
I returned one for replacement because the led lamp was blinking like crazy. The replacement connects to my usb alright but I have not done any extensive testing of the charging performance.
Inserting the phone is also fibbly because the slot is so wide, you need to take aim and align phone before inserting. This is a real bother. Do not buy it
I bought a Boxwave cradle for a 8525 and it's light blinked and failed within hours, I returned it.
mdshahed said:
I bought a Cradle for my TyTn II from Brando Web site. they are located in Hong Kong. I have been dealing with them since 2000.
they usually provide good service.
However this charger did not work, AC or USB part. I emailed them and they were kind to send me a replacement in 1 week.
Again still not charging or connecting to my computer. I skipped the cradle and tried the USB cable only still not working.
I emailed them back and they want me to ship both units back to them. I understand that there is a problem with certain connections charging or connecting with Kaiser an I tried to tell them that; I don't think they believe me.
Do Not Order this Cradle since it will not work !!
http://mobile.brando.com.hk/prod_detail.php?prod_id=03012&dept_id=039&cat_id=0996
Click to expand...
Click to collapse
I think all these cradles (Kigidi, mobile planet, Brando) are all from the original manufacturer. They do work, but not out of the box. You have to shift the battery around left to right while inserting them to have the contacts line up properly. Cheap quality.
I bought a cradle that looks exactly like that one off eBay. But it came with a second battery for Brando's price for just the cradle alone. I've been using mine for a little over a month, and am very happy with it. The USB cable only serves for charging and connecting to a pc. To charge the second battery in the charger 'tray', the AC power adapter must be plugged in as well.
Mine also has the tricky alignment issue when inserting the kaiser, but I'm used to it. Also because of the position of the kaiser's stylus, there's no access when cradled, so I rigged a mount on the side of the cradle for a spare stylus.
Hands down the best thing about my cradle is the charger tray and second battery. It's so nice to have a fully charged battery available at any time for a quick swap. The battery that was included is only 1300 mAh, opposed to the stock 1350 mAh battery, but it fits perfectly, and I I don't find the 50 mAh difference noticeable. And considering the $24 price tag fI paid for battery and dock, it seems a steal. At this point there's no way I'm going to shell out $50 for the 1650 mAh batteries now available, but If I din't have the dock and second battery I probably would have.
I see that the pricing is up $5, still a deal:
http://cgi.ebay.com/ws/eBayISAPI.dl...tToStoreCat&refwidgettype=cross_promot_widget
brando.com shipping
This is unrelated to the topic, but I was going to order from Brando.com and was wondering how long the shipping took. It says 7-20 business days, and I was hoping it would be on the shorter end of that. (shipping to PA)
Almost every charger didnt work with my TyTn II (after I burnt up mine original one on UPS). I just went to market, looked for highest wattage supplying adapter and it was LG's 5.2Volt 5W adapter. And it recharges my TyTn II like a charm. There is something bad with recharging TyTn II.
The old motorola charger and such going-around-boozo's worked with my Vox and Excalibur but not this beast.
Interesting
i have had one of these for over 2 years. its on my desk at work. the original mains adapter packed up a long time ago and i have an old tandy one attached now. does have the random blinking lights with phone and spare battery connected, but it works.
as said before, cheap design but very handy to charge phone and battery together.
just have to be a bit lucky when you buy i guess.
despite title, i would say buy.
@dark_prince: could be the charging socket in the phone is wearing and needs bit more power to kick it in. have you tried to clean inside socket with compressed air and contact cleaner, might help.
but maybe we just have to accept that our phones are really old now and dont work as well as they used to (i know the feeling)
Q: Suddenly my car charger (cigarette lighter plugged) is not working anymore. After 5 mins. my device stops charging..... is there anybody having the same problem and knows how to solve it?
If it's after a period of time maybe a battery contact issue?
vincentvdvelde said:
Q: Suddenly my car charger (cigarette lighter plugged) is not working anymore. After 5 mins. my device stops charging
Click to expand...
Click to collapse
If you've already read the sticky posts relating to car chargers and your (mystery brand) charger isn't one of those, then maybe your phones battery terminals and connectors need careful cleaning with a cotton bud moistened with contact cleaner or IPA. I had a problem with my mains charger ceasing to charge my TyTN II after a minute or two a long time ago and after cleaning as described, the problem went away. Be sure not to spray the contact cleaner or IPA onto the phone or battery, only the cotton bud/Q-tip and then gently rub that on the spring contacts and battery terminals. How does charging via mains adapter or PC USB port go?
Flying Kiwi said:
If you've already read the sticky posts relating to car chargers and your (mystery brand) charger isn't one of those, then maybe your phones battery terminals and connectors need careful cleaning with a cotton bud moistened with contact cleaner or IPA. I had a problem with my mains charger ceasing to charge my TyTN II after a minute or two a long time ago and after cleaning as described, the problem went away. Be sure not to spray the contact cleaner or IPA onto the phone or battery, only the cotton bud/Q-tip and then gently rub that on the spring contacts and battery terminals. How does charging via mains adapter or PC USB port go?
Click to expand...
Click to collapse
Thats the thing: adapter/ USB port works for recharging.... v strange
vincentvdvelde said:
Thats the thing: adapter/ USB port works for recharging.... v strange
Click to expand...
Click to collapse
It still could be a battery contact issue as voltages may differ slightly when using the car charger compared to the other forms of charging. As an example if the Kaiser is set to stop charging when the supply voltage drops below a certain value and the car chargers voltage is lower to start with (and fluctuates with normal driving/electrical usage) then that may explain things. It's well worth doing this cleaning every so often anyway as a matter of course so give it a try and see what happens.
Additionally, could heat be a factor eg if it's sitting on a hot dash or near heater vents (the device is designed to not recharge above certain temperatures)?
Flying Kiwi said:
It still could be a battery contact issue as voltages may differ slightly when using the car charger compared to the other forms of charging. As an example if the Kaiser is set to stop charging when the supply voltage drops below a certain value and the car chargers voltage is lower to start with (and fluctuates with normal driving/electrical usage) then that may explain things. It's well worth doing this cleaning every so often anyway as a matter of course so give it a try and see what happens.
Additionally, could heat be a factor eg if it's sitting on a hot dash or near heater vents (the device is designed to not recharge above certain temperatures)?
Click to expand...
Click to collapse
Thanks for the advice, i will give it a try
if you have any adapters that allow for another usb input, nice a headphone adapter, or the HTC Multifunction Audio Cable YC A300, a ycable or anything with a USB in, try that first.
if that doesn't work, take the unit into your retailer and they will give you a new (or refurbed) unit, as your USB port may have a pin or two out of whack.
This may be weird, but my tilt used to charge just fine from most USB chargers(car, AC, usb cords). One fine day it quit charging off most chargers except the official AC charger from AT&T. I tried to fiddle with the USB pins inside as one looked like it might be a bit bent/damaged. No luck.
However, yesterday I noticed that My Settings->System->Power->Advanced settings page had following option checked:
'When device is turned on, do not charge the battery when connected to the PC'.
Once I unchecked it, it started charging of PC USB cables (obviously), but strangely enough also charging from my car charger(s). Hope this works out for you or someone else...
jrd said:
This may be weird,
'When device is turned on, do not charge the battery when connected to the PC'.
Once I unchecked it, it started charging of PC USB cables (obviously), but strangely enough also charging from my car charger(s). Hope this works out for you or someone else...
Click to expand...
Click to collapse
It is probably because your normal USB pin 4 and 5 in the cable of your other chargers are not shorted to signal that there is no data connection. So your phone thinks it is connected to a PC (or a device which might send it data), hence not charging the battery according to that setting
I have a similar infuriating problem, i have had a MDA VArio III for over a year now, had an issue with my last one and had a replacement issued in October. Now i have used the Brodit active holder (ciggy lighter version) since day one over a year ago and wit the new MDA as well. now all of a sudden phone will not charge in the holder, borrowed a friends active cradle still no charge, used a no brand usb ciggy ligther charger and charges fine!!!!
When phoe n is placed in the holder orange charging light comes on but phone does not charge and the light goes out 5 mins later!!!
any ideas anyone???
thanks
Matt
Mattcity said:
I have a similar infuriating problem, i have had a MDA VArio III for over a year now, had an issue with my last one and had a replacement issued in October. Now i have used the Brodit active holder (ciggy lighter version) since day one over a year ago and wit the new MDA as well. now all of a sudden phone will not charge in the holder, borrowed a friends active cradle still no charge, used a no brand usb ciggy ligther charger and charges fine!!!!
When phoe n is placed in the holder orange charging light comes on but phone does not charge and the light goes out 5 mins later!!!
any ideas anyone???
thanks
Matt
Click to expand...
Click to collapse
Problem solved - Pin 5 on my phone was ever so slightly out of alignment, bent back into place and all is now well! strange it only affected the brodit holders, nothing else!
Car charger failure explained
I also experienced this same problem and actually broke my phones mini usb plug in frustration at lack of charging. Got it fixed again though
The reason for this problem has become apparent since my phone was repaired. In your car, like my car when the heater is switched on it will gradually heat up the cigarette lighter socket. My charger cable like yours has a thermal safety circuit built into it. So when the ciggy socket heats up the heat is transferred to the charger plug and breaks the elec charging circuit. You might see me driving around London with my charger plug hanging out of my window (to cool it down) on a Winter's day!!! Honk if you do.
The solution would be a cheaper charger without the thermal circuit built in. Go into Maplins or PC World and ask them for that..... They dont know what your talking about, because I have already tried.......! Good luck
You just need to make sure to enable your phone to charge when connected to PC.
Start->Setting->System->Power->
UN-CHECK the box that said "When device is turned on, DO NOT CHARGE the battery when connected to PC"
I have a M1000 which has sustained damage to the connector at the bottom of the unit so cannot charge it the normal way or connect to my laptop.
I have 2 batteries so am still able to charge each battery and then fit them alternately.
Is there anyone who can repair it?
I should think the hard bit would be finding a connector?
http://forum.xda-developers.com/showthread.php?t=310441&highlight=connector
Hello there,
I was charging my Qtek normally with it's original charger. My sister umplugged it a couple of times to charge up her notebook.
My Qtek won't charge anymore. It's working fine. It turns on, I can use it normally. But It won't charge.
My guess is that something happend to the mini usb plug or circuit, because it won't charge with it's charger, neither with USB cable plugged in the computer. And it can't communicate with the computer trought the cable too. Bluettoh works fine with Actve sync.
Someone have any clue about what happened?
Same thing happens to me today...
I'll show in the Qtek...
But I think that "usb plug" is "unplugged" from motherboard...
Visualy no problem with my usb plug... Welds are well...
So, the problem is IN the USB PLUG ????
I have found some on Ebay :
____://cgi.ebay.fr/5X-USB-Charge-Port-Plug-HTC-Pilot-Universal-Wizard-/400125580417?cmd=ViewItem&hash=item5d2957d481#ht_2473wt_1137
Is there some doc about ?
Thanks,
I Haven't opened it yet. I'm travelling, and I don't have the proper tools. But tomorrow I'll be back home and I can say if something physical happened.
So rocksull ? USB Plug is dead ?
I bought the connector and and external charger too (5$) with a battery (6$) on EBAY...
But usb plug is sent from USA, so I'll receive it in two weeks...
Bye,
Well.
I opened up my Qtek. The welds were messed up (Cold Solder). I'm just waiting a friend that has a soldering station to see if we can re-solder the plug. I'll post results soon.
Hello Rocksull,
So, It's good for you ?
I tried soldering USB plug, but welds are too small...
So actually I'm using an external battery charger... ((((((
Bye,
I was able to solder the plug back, because I work with that.
It charged again, but the battery didn't last 1 minute. I opened again and saw that the circuit is also messed up. There's one or two transistors burnt, a little capacitor.
Anyway... I gave up. I was about to buy a new cell phone anyway, and I can use the other componentes (LCD screen, camera, etc) to build some projects. =D.
I was able to solder woth a hot air soldering station (I don't know of that's the name) and some liquid weld. We have this stuff because we work with SMD components.