I'm aware of the various BT issues with the XDA II, and therefore installed BT Tools thinking it may allow me to use my handfree kit. Unfortunately I'm experiencing problems and not sure if this is me doing something wrong or there is a problem with the software. Basically the XDA II does not route either incoming or outgoing calls via the handfrees unit. I have do the following:-
1. Installed the latest BT Tools.
2. Created a bond with the Nokia Handfree kit, when prompted for the BT profile (the BT Tools icon screen) I select headset only.
3. Enable BT on the XDA II
When I make or receive a call is there any button or menu I should be selecting to enable the handsfree unit?
From the Today screen, make sure bluetooth headset mode is enabled.
And if Bluetooth Headset Mode does not appear on the today screen:
Start -> Settings -> Today -> Items and make sure Profile is checked. That will put the headset mode switch on the Today screen.
Thanks for the suggestions, I must admit I had missed the headset profile on the Today screen.
Even with the device paired, BT enabled & the Headset enable neither incoming or outgoing calls are routed through the handsfree unit.
Any other suugestions welcomed...
With the new bluetooth tools you need to transfer the call to the headset...
I find the best way when dialing is to have the phone ready to dial, then i hit the answer button on the headset causing the phone to dial & transfer sound to the headset @ the same time.
When answering the call the headset should ring and you press the answer button on the headset to recieve the call.
Ta
Christian
When you say press the headset button are you referring to the headset icon on the XDA or the Nokia handsfree button?
If its the Nokia button , I'll try this tomorrow, if not, then the icon does not ring and when receiving a call it is covered by the incoming call window.
Many thanks...
the nokia headset button
ta
Christian
Yep thats what I thought, I think I can confidently say there is a compatability issue with using the current version of BT Tools with the new Nokia CK-7W handsfree kit.
I've read the user manual for the handfree kit and that refers to switching/transferring the call between the BT devices using the button. The unit clicks as if there's something happening, but no call is heard, the unit works perfectly with a BT phone connected both Nokia & Motorola.
I would try uninstalling pocket BT tools - for using a headset it is of no additional value anyway. I do not have it installed and have never had any problems making or receiving calls with my SE HBH-30 headset.
Try using the earlier version of bluetooth tools, make sure you uninstall the version you have and also unbond/remove bluetooth pairings, rebond after successful install.
Pocket Bluetooth Tools is perfect! This is what I'm looking for, except I can't figure out how to listen to music thru my bluetooth headset.
Thanks for the great tool though, now I can make calls with my headset.
BRosenow said:
I would try uninstalling pocket BT tools - for using a headset it is of no additional value anyway. I do not have it installed and have never had any problems making or receiving calls with my SE HBH-30 headset.
Click to expand...
Click to collapse
The BIG advantage is battery life and not having to re-enable the headset profile each time you switch on the phone! With both PBT and/or Profile not displayed, I also get more Today real estate to play with.
With BT on all the time, I'm lucky to get four hours usage out of my Xda II, with PBT turning it off after five minutes the time can go up to almost seven. Sure, there is a short lag between call coming in and the headset (HBH-65) ringing but I can live with that and it even works well with Pocket Zen Phone. I also like the last number redial facility it adds to my headset. PBT rocks!
I found one problem with this program. My device won't automatically turn off after installing this tool. The backlight turns off, but not the device after certain minutes set. Who do I report the problem too.
i have got this problem to carnt get the xda i to connect to my car blue tooth hands free kit it finds the kit but nothing gome on guy get ya thinking heads on n help :idea: to revolve this problem
i have got this problem to carnt get the xda i to connect to my car blue tooth hands free kit it finds the kit but nothing gome on guy get ya thinking heads on n help :idea: to revolve this problem
Hi everyone,
well, I got the same problem :x with my XDA2, also called Qtek 2020, and Nokia carkit 112. It just does'nt work, even with BT tools. But I wonder how you get the icon screen while connecting to your Nokia carkit...cause mine is going straight back to the "Bluetooth connected devices" screen. I only got the icon screen, enabling the profile selection, while connecting to my Nokia 6310i phone.
Let's hope that HTC is gonna come up with Handsfree profile soon...
Regards to all, special ones to our OZ friends!! Mates, I really enjoyed living in Sydney, even if Italy is quite convenient as well.
Chris
Related
I have an i-Mate (v1.52.00WWE) and two (2) BlueTooth headset devices:
Parrot CK v3.11 - Car Kit
M3000 by Plantronics - Ear Piece
Both are bonded, but I guess I can only ever set one as my default at any time (obviously you can't have the call ringing in two places at once - but that would solve the problem!).
Is there a way of switching between them simply?, or having them 'auto select' the correct default profile?, or having them both active at once? I currently have to rediscover them to switch.
Would this be made easier if the i-Mate had both Headset and Handsfree (?) profiles? Is this available?
Hope its not such a silly question :lol:
Thanks in advance,
Ian
I have BT carkit, and BT handsfree,
and I have the same problem.
With my Nokia 6600, it works great,
there's no "default profile",
both works.
Even more confused now
Thanks for the reply - I'm even more confused.
What I ment to say that with the 6600 it works great, :lol:
unlink the i-mate pocket pc. :roll:
I have just purchased the xdaII and found this problem too...
Have you found out any more info on this?
The only thing i can do at the moment is rename the bluetooth device and it then prompts me to set as default...
Ta
Christian
Thanks for the tip
No I have not found out more.
I tried the widcomm drivers, but found headset was all screwed up.
Thanks for the tip on rename. I have been deleting and recreating.
Now we only need a application on the Today that can rename the two BT devices and back.
Maybey a reg.key-file we can 'click' ??
One more of the shortcommings of XDAII in anything related to the BT sofware.
I read about a new ROM version comming out soon, that is supposed to fix the those BT problems, Has anyone more info on that?
:?:
IanF said:
I have an i-Mate (v1.52.00WWE) and two (2) BlueTooth headset devices:
Parrot CK v3.11 - Car Kit
M3000 by Plantronics - Ear Piece
Both are bonded, but I guess I can only ever set one as my default at any time (obviously you can't have the call ringing in two places at once - but that would solve the problem!).
Is there a way of switching between them simply?, or having them 'auto select' the correct default profile?, or having them both active at once? I currently have to rediscover them to switch.
Would this be made easier if the i-Mate had both Headset and Handsfree (?) profiles? Is this available?
Hope its not such a silly question :lol:
Thanks in advance,
Ian
Click to expand...
Click to collapse
I just rx'd my Plantronics M3000 headset. It bonds to my XDA2 but I cannot for the life of me, answer or make a call with the headset.
1. When searching for a Bluetooth device, it finds the M3000 by Plantronics
2. I highlight it & tap next
3. I enter the bond code
4. I give it a name & tap finish.
Then it asks me, "This Bluetooth device supports headset profile, would you like to set it as your bluetooth headset?"
I answered Yes but I can't do the calling. Should this be answered No?
I originate a call on the XDA2, when it connects, I press and release the headset TALK button, hear a tone in the earpiece but the call never switches to the headset.
I have the green 3 sec blinking green light so unit is on. XDA2 has the blue indicator blinking.
Any feedback would be helpful since you do have the Plantronics,
Regards
Craig
Hi cshields1!
I don't have a Plantronics, but two SE HBH 30 and HBH 35 that work "somehow" with my XDAII.
First I would reccomend you to upgrade your ROM, since the Bluetooth radio stack of version 1.06.01 seem to have improved a bit over the previous ones (just in case you haven't yet)
Second, no matter what you do, actually you would NOT be able to initiate a call from your headset, you just can answer an incoming call and end a call, that is with the poor BT support in the XDAII.
Third, I'm not sure what you do, but please check:
- once your headset is bonded, turn your BT setting back to ON (BT icon on the bottom right of the Today screen)
- be sure your phone is NOT in flight mode
- Check that your "BT headset mode" in Today Screen is enabled
Tell me if this works.
:wink:
Hi, all.
Hope someone can assist me. I'm using an XDA II that has been upgraded to 2.06 Windows Mobile 2003 SE.
I have enabled the Bluetooth Headset profile on my Today screen and calls will transfer over to my headset (SonyEricsson HBH-65).
My question is for the following scenarios:
1) The calls transfer over but sometimes the connection becomes lost while I'm still mid-way in the call. How do I instruct the XDA to transfer the call to my Headset again? Tried pressing the button on my HBH-65 but the call doesn't transfer.
2) Sometimes, I put on my headset but forgot to turn it on. When a call comes in, I realise my mistake and answer the call on my phone first but then I ask the other party to wait while I turn on my HBH-65. After turning it on, how do I transfer the existing call to my headset?
Hope someone can help with some advice. Thanks in advance
1) I currently use BlueTrek G2 and so far has got no probs at all.
2) The BT headset has to be running before the phone in call. For the BT signal it has to be sent right b4 the phone in call.
I guess that's how you can get ur headset running.
I've got that to my best. Good luck...
No problem with them...
i am using BHB-65 too, they are great ,man, i have no problem with them from the first time using.
1. When you want to connect to the headset, there's an icon near the phone icon, you touch on that , it will indicate the term to transfer the call back the headset or cut it out.
2. When you forgot turning on the BT headset, just turn it on and press "enabled the headset" (on the desktop, remember to "view the profile" in item "Today"), it will automatically transfer the call to the BT headset.
Wish you could do that.
The idia is to use bluetooth headset (in my case HBH-600) with SE T630 and my Compact.
T630 pairs with headset only during incoming or outgoing call, in stand-by mode my headset is absolutly free to connect to my Compact.
And since my Compact connected to handsfree it's not letting it go. Even when my device is turned off headset remains connected to it. On the one hand it's good, but in order to make headset work with two devices I should get rid of that feature.
I've seen a thread where people (with feature mentioned above) said that our devices don't think that answering a call is "using" the device and turn off. So other party of conversation couldn't hear anything.
Do you have any ideas how to break bluetooth connection with headset after call?
Thanks in advance.
Perhaps Pocket Bluetooth Tools will help you, it can auto-off the BT on the device after the call is complete and re-enable it when a call comes in.
Be aware, however, that some people find it can cause more problems than it solves - I however love it on my Xda II.
Thanks for tip.
I've tried that a long time ago, but found it of no use for me at that moment.
I remember that there is "settings" for it, but now I can't find it.
And another question. On that site it is said that program supports bluetooth handsfree and headset profile, and what about voice dialing?
you also can use Pocket Zen Phone.. schedule your profile to set the bluetooth off at certain time.
Hi all
does anyone know if there is a app that while in bluetooth sync mode with a bluetooth handsfree device could launch a switch when a incomming call comes in to give the option to select the call by bluetooth or phone or phones speakerphone? i saw this option on a iphone. if this app is not available could some maybe create one? this would be a great function for windows mobile device. i do know that there is a option after you answer the call to turn off the bluetooth but its in the menu option and not as accessable...
thanks for you help..
J
It should work simply like this on WM phones (at least on all the WM phones I have). When a call comes in:
1. If you press talk button on your Bluetooth handsfree, the call should get picked up through the handsfree.
2. If you answer the call on the phone by pressing either software or hardware button, the call is picked up on the phone.
Thank you for your reply i just have another question
will that be the same for if the phone was synced to a car bluetooth kit as well? i just want to know if so as maybe the rom i have has problems doing this...
I tried to do what is posted and it did not work for the car i answered from the hardware keys as well as the software keys and still picked up in the car. i jave to click menu then turn off hands free. is there some other option i need to select in some settings to change the way the hands free works? I will try with a blue tooth ear piece to see if there is a difference..
In looking more into this there are 2 profiles 1 is headset and the other is handsfree i believe ear pieces use the headset profile and car kits use handsfree profile i did check the earpiece and it worked as described above does anyone know how to change the handset profile? is this a reg setting or can someone tell me how these profiles are stored in winmo 6.5?
Hi Folk
Ive had a quick search and not found anyone with the same issue.... might be cos the phone is new out.
I have a parrot bluetooth hands-free kit in the car and since changing from the iphone to the DHD i cannot use the call pickup button to call out like i would nomally do in the iphone.
Is there something i need to do or is this function not availble on this phone? Im new to the android software so ive probably missed the obvious.
Thanks in advance
Muzzy
A also have a parrot BT kit ( Mki-9000) but I don't have such issue. I can play music via a2dp, and also I can make calls and everything works fine.
The only issue I have is when i want to answer an incoming call - if I answer through the phone ( by pressing the green button) the sound is not forwarded to the BT kit. I don't have such issues with my Nokia.
I can't test right now what will happen if I answer through the BT kit because my Steering Wheel remote control is out of power.
To resolve your problem try to search the parrot website's forum also check for the latest firmware updates for your device. In the past I have similar issue with HTC3300 but after firmware update it was fixed.
The issue I have (mki9200) is that A2DP seems to be on permantly, so when listening to my ipod through the parrot, if I have satnav on, then the directions come through the parrot kit. If a new email or txt comes in, the notification comes through the parrot. With my old Omnia, I could deactivate the Headset profile (A2DP) and keep the Hands Free profile when I was connected to my parrot.
Can this be done on the DHD.
(ignore my footer - can't seem to change this at the moment)
jazzymc said:
... The only issue I have is when i want to answer an incoming call - if I answer through the phone ( by pressing the green button) the sound is not forwarded to the BT kit. I don't have such issues with my Nokia.
I can't test right now what will happen if I answer through the BT kit because my Steering Wheel remote control is out of power. ...
Click to expand...
Click to collapse
Check out ... http://forum.xda-developers.com/showthread.php?t=834983&page=3 .... my post #22. Should answer your *problem*. I had the same thing when switching from Nokia to HTC .... But if you check a couple of posts later I've also found that I can use the phone to initiate a call and the sound *does* go to the Bt device ....
Dave