Hello,
on my XDA I the Pin 22 is broken (charger Pin).
Is the Pin 21 the same, so I can modify my USB cable to use this pin instead of 22 ?
Greetings
Disrupter
Taking a look at http://wiki.xda-developers.com/wiki/Connectors i think this should work.....
HTH
Stefan
I tried it and it´s charging again.
Very helpfull site
Related
Your guide to making serial cable is a bit iffy! You say we shall call this pin number 1 but we haven't got any confirmation about this... Is it pin 1 or not - doesn't fill me with confidence
Is it possible to make a USB to serial adaptor cable? I assume not as there arn't enough wires on the USB cable but I'm not familiar with this at all - yet!!
I've searched the web for a guide to serial cable pin layout but I can't find anything anymore.
Might just go and buy one and hope for the best.
Cheers
Fud
Also...
Can see anywhere if you can use a laptop to connect via IR com1 and unlock the xda with Manipulator.
IR port is not active.
So no this is not possible.
Can anybody help?
I still cannot get this to work. I have made my serial cable using a null modem cable and the board inside the O2 cradle. I have used a circuit tester to find the continuity between the actual XDA connector and the power connector for the cradle (con2 i think) - It has all the relevent pins for the serial connection.
Manipulator sits on the scanning ports screen and ActiveSync seems to be stuck in a loop but does not connect. I have obviously disabled ActiveSync b4 trying to connect with Manipulator and vice versa.
I have also attempted to rewire this as advised by one of you on another forum - using just the TX RX and GND pins as I am only trying to unlock the phone. This still does not work.
If somebody could send me a diagram of the serial connection it would help because the instructions here are a little vague. With just TX and RX connections I have wired up as so:
Com Port------------XDA----------------Con2
2-----------------------8-----------------5th connector from left
3----------------------10----------------7th from left
5-----------------------2-----------------1st from left
Also looking down on the circuit board with con1 away from you and con2 toward you. Con1 Pin 1 is on the right - right?!
I could go and buy the cable but to be honest I would probably just go and get a new phone on O2 to use that sim. I would really like to get somewhere on this coz it's now annoying!
Working
Sweet, Sweet, Sweet.
Didn't work with Manipulator but works with terminal prog??
I am now unlocked
Radio 4.06
Wallaby 5.15
Dunno if there is a prob with it - but just to let you know...
THX
Can somebody tell me which wires from my adaptor on which pin i need to set.
I have readed about pin 20,21, and 22, but i have no idea about the + - and GND
Take a look at this site:
http://wiki.xda-developers.com/wiki/Connectors
HTH
Stefan
UDC- pin on motherboard was broken. Can anyone tell me were I can find another way to connect UDC-,UDC+ and VDD on motherboad?
Hi
Could anyone help with hooking up an RS232 link between my XDA2 and some CNC machinery?
In the past I have had success with Rx, Tx GND and software handshaking between CNC and a laptop. This is what I'm trying to emulate here.
On a XDA cable I removed the 9 pin female D type and replaced it with a 25 pin male.
The brown wire was originally connected to 9pin/2 (rxd???) I now have this going tp 25pin/2(txd??)
The red wire was originally connected to 9pin/3 (txd??) I now have this going to 25pin/3 (rxd??)
I've configured demo versions of PockeTTY and vxHpc to check for any upload / download activity and the IR beam is switched off.
I see absolutely nothing.
Any ideas? Is the XDA fundamentaly not suited to this application?
On the 25 pin the shield connects to pin 7 and 4/5 and 6/8/20 are connected respectively.
Any help appreciated.
Regards
Rob
maybe this will help
http://www.jspayne.com/io/schematics.html
otherwise more hits here
http://www.google.com/search?hl=en&q=serial+25pin&btnG=Search
The micro usb port is broken, and its a common problem on this tablet.
How can i fix this?
I can not solder the port onto the mainboard again, see the picture why..
But can i get power and data+- from the docking port?
yes you can.
good
But which pin should i connect it to?
http://rootzwiki.com/topic/8523-reverse-engineering-the-dock-charger/
And can i connect it to since the docking port should have 20v?
1 charge
2 gnd
3 charge
4 hdmi pin 44 In D3-
5 Charger control (to pq2)
6 hdmi pin 45 In D3+
7 hdmi VDD 3.3V
8 gnd
9 gnd
10 hdmi pin 47 In D4-
11 USB Micro D-
12 hdmi pin 48 In D4 +
13 USB micro D+
14 gnd
15 USB Master D-
16 nc
17 USB MAster D+
18 nc
19 gnd
20 hdmi pin 29 SDA
21 gnd
22 hdmi pin 28 SCL
23 hdmi pin 41 IN D2-
24 hdmi pin 7 HPD_Source
25 hdmi pin 42 In D2+
26 gnd
27 gnd
28 audio out L
29 hdmi pin 38 IN D1-
30 audio out R
31 hdmi pin 39 IN D1+
32 headset inserted switch
33 gnd
34 mic inserted switch feed
35 USB micro +
36 mic inserted switch
37 gnd
38 mic tip
39 + 5V to usb master
40 mic ring
Buy a dock.
Sent from my HTC EVO 3D X515m using xda premium
berbecverde said:
Buy a dock.
Sent from my HTC EVO 3D X515m using xda premium
Click to expand...
Click to collapse
i dont want to