I have an O2 XDA and the unit seems dead this morning! the led is RED when in the dock and connected to the mains. It will not respond to any thing has it died? help
the red led means the battery is almost dead ... charge it
Its connected to the mains suppliy and is just getting warm, the LED is dim red hard and soft reset will not do anything
will it hardreset ?
No hard or soft resets do nothing
I had a similar problem last year and in the end, I performed a cold reset by deactivating the battery for a couple of minutes and recovering from a backup.[/b]
may be send to repair
may be u will sending to repair or change internal battery... how o
d r xda ?
sorry in bad english
Iv'e tryed removing the battery and leaving disconnected for 30 mins reconnectong but still nothing. It just will not switch on. when it is conneded to the charging cradle I only get a dim red LED. Am I the proud posessor of a futuristic paper weight?.........
It sounds like either the battery or the charging circuit are defective. Warranty problem!
Data
@aeroreg
I'm going through the same thing now. My XDA is dead! Exactly the same problem like yours. Have you sort it out?
bad RSU can cause the same problem ... do you still able to use the phone part (GSM OK) ?
dead XDA
Have seen similar where unit will not charge and battery eventually flat. Was caused by internal miniature fuse being blown insideXDA. Had to jumper it with fine wire soldered across with miniature iron (and steady hand !!!).
This fixed problem. Somewhere on this site is description and pictures by fellow sufferer (late last year if I remember).
Have you by chance tried to use an iPAQ cable to power your XDA ?? this causes this problem for sure.
regards
@awhitlock
Can you post the link of the despriction? I couldn't find it. And no, I didn't use an iPaq cable.
@Biso007
Bad Remote Software Update? I don't think it causes this problem to my XDA as I still think it's more hardware related. Any chance how a bad RSU can cause such problem?
Guys, I tried hard reset and switch on the XDA simultaneously, and immediately there's a screen of four thicked coloured lines, (which is White, Red, Green and Blue) and written "WALLABY Bootloader V5.17" on the white line and "GSM ERROR" on the blue line. Any idea on this? :S
Cheers,
RSU = Radio Stack Upgrade
what you got is the boot loader screen ... if you can see "GSM OK" then it's not RSU problem ... most propabley will be h/w or bad battery problem
I have also died XDA same way
I left my xda to recharge when I came and unplug it it was dead already
I tried to change battery, but it doesnt want to work at all. With Old battery when I place it to recharde the red light is flashing for a while then going down.
Do you think it may be repaired by myself ?
The issue is that in Poland I didn't found ANY service from XDA
thanks for help
fuse
definitely this is broken fuse, small micro fuse right beside the connector pins on the motherboard.
@Biso007
Thanks for correcting me on the RSU. To be honest, I'm a newbie in PDA, all I know is just use it, charge it, and clean it when it's dirty :|
I thought of changing the battery but what migdalt stated out is worrying me a little bit, I'm afraid after changing the battery, the problem is still there.
@JGUI
Any chance for you to show me how to fix my XDA?
Geez, XDA is problematic! :|
hey guys i have da same problem...XDA is dead and when i put it on the cradle da same red light is seen above!wat maybe the problem....im in pakistan and we dont have ne repair shops here....anyone out dere who can help me out!?
Anyone...?
Sorry to tell you so
Hi there, I'm really sorry to tell you what Biso has already said, that if you get GSM ERROR in the Bootloader screen so you have killed your XDA by upgrading the RSU
wish you better luck to find a solution for it soon
Related
Ok, it's tarted 2 days ago, suddenly my new exec screen going to blue (Like PC)??? just blue color (Sometimes white and black stripes) and hung, so I just restart it. But today, is terrible,its happend 6 times. Tonight the worst thing happend, blue screen come again but this time with soft reset, not help at all. Every time I soft reset the splash screen comes, and then that blue screen again. It happend about 5 times, the machine finally start but can't read my sd card and I try to do soft reset but screen goes and never come back. My exec didn't start at all. I tried to release the battery, leave for few minutes and put it back try to start it, nothing happend... now my exec has die.
Anyone please help me and advice please,
What I did just cook ext ROM (So it have autoconfig for my country's operator, and upgrade the radio to 1.14.10 from T-Mobile, like I did to my alpine but it have no problem until I sold it)
Whoa... help me bro...
Thanks in advanced
Finally it's start but never reach windows screen, the blue screen appears again.
And I remember, the strange thing, my IMEI that I read from device properties is: 355195002465655
But, the IMEI at back body,(Under the battery) : 355195000360361
Why?And what happen?
guess u have the same probs as some others
http://forum.xda-developers.com/showthread.php?t=291986
oops:
saw u r already i that post.......
OK, I've got the same problems as you did. I was so upset with the device that I hit it on my lap (with the battery clip side hitting my lap) and then put the battery back on. Then it turned on! So everytime I have this problem I just hit the battery clip side and it turns on like 70 percent of the time. I just realized the SD card is on that side...hmmm..must be something to do with SD. I'm pretty sure someday it would just stop working at all if I keep doing this.
I don't advise anyone doing this but so far it works for me. I still have problems waking it up though. I really think the mainboard is messed up so I'm trying to get a mainboard, even a broken miniusb mainboard just to test it out. I opened mine up to the last screw and no loose connections noted. So if anyone has a mainboard then can sell me PM me.
If you still have warranty on the device, I advise you to send it in for warranty repair. It seems to only get worst and not better. Goodluck, hopefully we can find a solution for this. If I do get a mainboard. I'll let you know if that fixed it.
Hmm, I've guess it, I think the pprob is mainboard. I'll send it for warranty, (But I bought it in other city not in my own city) So i'll have to send it then on friday this week i'll go to that store to check arround and maybe choose the best product. I'll give the update then.
Anyway someone can give a advice to choose the mainboard?
Thanks in advanced.
bump..we need help..Is it a mainboard or coaxial cable problem? Please advise..
OK, Problem found.. Thanks Corneluis...It is a problem with the voltage control on the mainboard! Anybody has a workaround for this?
SOLUTION FOUND!!! At least for my Jasjar. Thanks, cornelius about the info on faulty voltage control which causes the Bulverde CPU to hang and give funny lines and colors to the screen. The solution is to install Pocket Hack Master and disable the Device CPU scaling in settings and set the speed to 312mhz for standby and before you turn it off. Now you can always clock it to 520 when needed but before you turn it off or close the screen make sure the speed is only 312mhz.
This has worked for me for more than 24 hours without any sngle hang.
I bought the Qtek 9100 from a seller on ebay who listed it as faulty due to not booting..
I assumed it was most likely the battery, So I ordered it, cleaned it up a bit, waited a whole MONTH for the battery to arrive (Damn you customs! haha), charged it, And whoop, it turned on.. Kinda..
It showed the O2 boot logo, then suddenly the screen started showing this very bizarre set of lines almost as if the ribbon was broken.. this however couldn't be the case, as the O2 logo was displayed fine, and opening and closing it didn't affect the screen..
So now.. Having booted it and had it crash before even loading windows, it refuses to turn back on, So I attempted every trick to hard reset it.. No luck
The only luck I've had, is holding the power button down for 30 seconds with the battery removed, and putting it back in for it to complete the above syptom.
I'm assuming as it boots the logo perfectly fine, it's not the battery (it's brand new, and is charged from a separate charging facility) Not the screen either.. So, It's got to be something else? :S
I'm trying to put as much information possible as to get the most informed solution to my problem :/
I'd truly love a solution for this as I've spent the remainder of my money on this phone (only a student) and really require a working phone soon.
Thank you so very much , PLEASE HELP! D:
Thanks guys lul
problem
plese forgive me for my bad english but i hope you understand what i try to say! i have 2 qtek 9100 with the same problem! i i resolve the problem in one way at both of the phones! i disassemble the phone on the location of the display screen and there is 2 integrated circuit boards and between them i put a piece of paper and at the bottom of the screen one horizontal piece it seems that was the problem integrated plates touching each other is that the phone was disassemble before! i hope this information will help you !
hi guys
well ok here is the story
I got htc touch elf
in past i have flashed many roms, upgraded radio,uspl & all & everything was working fine but today phone was in my pocket & when i take it out no display but network led flashing, so I soft reset it but it didn't turned on. I even tried charging but the orange LED light didn't come on(even after 10 mins of charging). than i removed my battery & after 10 minutes i placed it in & turned on my phone this time it starts. So i quickly hard reseted the device & it worked fine. But within few minutes when its customizing the device it turned off & screen goes black. I tried turning on & it turned on & quickly adjusted back light settings. & was editing time it hangs & again turned off. I tried again & again sometimes it turns off at smart mobility screen. & later it didn't even turn on & no charging light even when plugged into charger. I took out battery again & placed it in & it utrnd on but turns off in few minutes.
My touch is almost 2years old & orignal stock battery since i purchased touch
i guessing that it may be battery issue cause i was able to go in try colour boot loader screen but it fades & changed in to dim white screen.
It also happens in smart mobility screen & turns reddish or blue & than turns off.
any ideas guyz
watz this issue
I am guessing battery issue but in try color screen it fades to dim white screen & from past 20 minutes its still in that dim white light(picture attached)
so is battery corrupted or any hardware issue.
any help will be so helpful
thanks
waiting for your replies
PS:- & when i was able to log in windows i checked battery status it says 70%. after 10 minutes of without battery I reinserted battery & goes to tricolour boot loader screen This time it didn't fades.
But when i soft reset device it stays in red colored smart mobility screen see pic attached
no one wid any idea
here's what u can do...try to hard reset till u see the tri color screen and then flash it with a stock ROM with the W/O 6.1 it should turns into green color..then just configure it as usual.
Try with a fully charged battery, if battery is not the issue then put in a fully charged battery and then flash a stock ROM, don't risk a flash with this battery, it may die in between of a flash ( maybe battery cycle issues 2 year old batteries can give these ). Flash stock with a new battery which is charged to 100%.
If not just manage a flash to stock and go to HTC support, maybe issues with harware.
You sure no moisuture/water went it ? These phones are tricky if moisture goes in and creats issues with motherboar an the tocuh screen can cause re-boots etc etc.
thanks for your reply guyz
I visit service center & they told me that its motherboard issue.And they cant fix it..have to buy new motherboard but as it costs 70% of the price of mobile so better to buy a new one
After searching web for it I found that HTC has these motherboard issue. There hardware is not long lasting.
As promised, just replying to this now. have just seen your last post. It does indeed sound like a hardware issue - I was going to guess at the mainboard. Have you tried flashing on a different ipl/spl etc? I wonder if that may be de stabilising your device for some reason? Also, guess you could try another radio. I have 3.21.90 on both of mine. Can't remember what IPL/SPL combo I have going.
Sorry to not be of more use. By all means feel free to see what JTAG can do for you, but I seriously doubt you will be able to alleviate this situation, and at the same time, HTC/Service Centre would be a little less willing to help.
They also tried to charge me £90 GBP to fix an ELF.... that is more then I can buy them for!
Stu
captainstu72 said:
As promised, just replying to this now. have just seen your last post. It does indeed sound like a hardware issue - I was going to guess at the mainboard. Have you tried flashing on a different ipl/spl etc? I wonder if that may be de stabilising your device for some reason? Also, guess you could try another radio. I have 3.21.90 on both of mine. Can't remember what IPL/SPL combo I have going.
Sorry to not be of more use. By all means feel free to see what JTAG can do for you, but I seriously doubt you will be able to alleviate this situation, and at the same time, HTC/Service Centre would be a little less willing to help.
They also tried to charge me £90 GBP to fix an ELF.... that is more then I can buy them for!
Stu
Click to expand...
Click to collapse
yup. I tried flashing diffrent radio and roms. But it didn't worked. will flash ipl spl if it comes back to life again
thanks again for your replies
No need to say thanks. I wouldn't be on this site if it wasn't for others helping, not would I have bothered posting my attempts at jtag etc
Let us know how you get on, I am intrigued to see what could be going wrong on your phone.
Hi im from Germany,
i tried to flash my Acer S200 but it stopped by 50% and i have pluged the cable out. I cant turn it on, it gives no signal, i cant bring it to the download mode. Nothing is working no hardreset with buttons.Nothing is working and when i plug it to usb the LED isnt blinking
Sorry for my bad english ..
my phone is new, it has garanty, should i contact the acer support or can anyone help me ?
Hold volume up/vol down button + reset until you see "clean boot"
i tried it the phone gives no signal .. no clean boot is coming .. the rom flashing was at 50% i think it is breaked
but thank you
did you try removing then replacing the battery. then try bootloader mode again?
yes i tried but nothing is working i cant enter the bootloader nothing is working it is just off no vibration nothin is working
sorry, but I have to ask, are pressing then holding vol down +power +camera buttons
at the same time until blinking red light starts?
you have to get into bootloader mode then flash a custom rom
brainmaster has a few including a "clean" rom.
I had this happen awhile ago and tried so many things for 2 days that now I don't
remember what actually worked! But I don't think that your S200 is bricked.
Also, make sure that you keep the power cable pluuged in (not usb)
you need a good charge even if you don't see the green light.
just keep trying and if I can remember I let you know.
or someone here will help you to find a solution!
thank you for your help but there is no light blinking. Also when i plug it to charge no light is going on. it doesnt charge the battery. i hope you can remember
i already know how to flash a rom but the phone doesnt give any sign
sorry I can't remember but you should ask brainmaster and maybe he can really help.
And he speaks german= )
thank you i will send him my problem
Any solution
Hi. I kind of found myself in the same situation. My acer s200 is unresponsive, no blinking lights no matter key/reset combinations. Had been in the middle of flashing on a new ROM when it got accidentally disconnected.
Any possible solution? Already checked the battery out in a different phone and it's fine and charged.
Hey,
i don't want to looks like a vultur, but if some of you can't find a solution to resolve the problem you have, I'm interested by the device because I need some piece. Of course I hope you can resolve your problem but if there are no led blinking, the last possibility is to send it to acer, and if you don't want to wait/pay/or whatever to with the acer support, I'm interested by your device.
Arto
Vulture indeed!! I'm need of help man.
you still need help?????
Hey GarcoG. Yes, still in need of help. My S200 is currently a desktop paperweight at home. It's a beautiful paperweight but it was made for so much more. Would really like to get it up and running again.
A new thing I noticed. I'm able to charge my phone's battery to full on my friend's s200. Of course when I put it back into my phone, it's still completely unresposive. However, I noticed that whenever I put it back into my friend's phone, the charge on it has reduced. I'm pretty sure it's not a battery issue I have since my phone is still unresponsive with my friend's battery in it and the same happens with that battery as well.
Would really appreciate any ideas on fixing this.
Hi, count me in. I just jumped on your wagon.. will try to disassemble this beauty soon before I officially demote it to a shiny paperweight.. well it's not that shiny, i put on a matte screen protector on it
Really funny about that matte screen protector. Cannot wait for the results. In my case, phone got accidentally connected just as it had reached the stage of flashing on the new ROM. Was thinking it was probably unresponsive because the ROM instructions that enable it respond to key combinations are absent hence cant get it into Bootloader mode.
@ incognito_tkd: Any luck with the disassembly? Would like to know your findings.
I have same problem... same situation
But... when I connect my USB charger, it shows red LED on... as if the charging is ON. But no reaction
Any one help please
there is no possibility to repair the phone... you have to send it to acer !!
i got my phone 1month after i´ve send it
Hi there,
i have search but can't find anything
A friend of mine just gave me HD2 and i was super excited about it.
The phone wasn't used for ages so i plugged it for 10 minutes and while plugged i tried to turn it on.
the phone started to vibrated continiously without displaying anything.
I removed the battery, unplug power, inserted battery again and it just vibrates like nuts
Once out of 5 (roughly) it flashes... the flash and then vibrates... again nonstop
once out of 10 (roughly again) it just doesn't do anything at all.
even when plugged to the power, no led or nothing.
did i get a dead beast ?
I tried, holding buttons, pressing reset button, etc but with no luck...
hope you guys could help me... many thanks in advance
Check the battery pins on the HD2 and make sure that non of them are bent slightly or anything like that. A slightly bent battery pin can cause the HD2 to do some crazy things. If non of the battery pins are bent then you might just have a bad NAND chip and the only fix for that is a new main board.
Nice bike in your avatar pic too by the way.
just checked them all out and they are well aligned and don't seem to have been touch
that sucks
Cheers for my ride i like it too ^^
cheers,
i just checked them all and they all look just fine
sound like i am fu**ed am i ?
Cheers for the ride I like it to, a least it works
wuub said:
cheers,
i just checked them all and they all look just fine
sound like i am fu**ed am i ?
Cheers for the ride I like it to, a least it works
Click to expand...
Click to collapse
Dang man that does suck, I hate to tell you, "Yeah it probably needs a new main board.", and then someone else come up with another idea. But I do think that is going to be your fix. i say this cause if it was bricked it would more than likely vibrate one brief burst and that would be it, nothing else. but the steady vibration sounds more like a bad component on the main board. Sorry friend that is my opinion. Maybe I am wrong though.
something new happened this morning
I left the phone without battery all night and put the battery in when i got up.
the screen displayed the following message.
/!\ Software update failed. Please Try again.
I couldn't do anything from that point so i pressed the reset button... (didn't want to remove the battery)
phone went off....
as it wasn't responding to anything... i took the battery out and back in.... and brrrrrrrrrrr ... back to scare one
any ideas ? doesnt smell good ...
PS : sorry for double post, hotel connexion in cyprus does really suck.
speed is bad and unstable... they have 150Mb line for the all island (no joke)
cheers
wuub said:
something new happened this morning
I left the phone without battery all night and put the battery in when i got up.
the screen displayed the following message.
/!\ Software update failed. Please Try again.
I couldn't do anything from that point so i pressed the reset button... (didn't want to remove the battery)
phone went off....
as it wasn't responding to anything... i took the battery out and back in.... and brrrrrrrrrrr ... back to scare one
any ideas ? doesnt smell good ...
PS : sorry for double post, hotel connexion in cyprus does really suck.
speed is bad and unstable... they have 150Mb line for the all island (no joke)
cheers
Click to expand...
Click to collapse
keep the volume down button pressed then swutch on your phone ...if you go into a tri colour screen ..then you might be in some luck ....then you have to go to the official htc site and download a rom update from there ..and flash it ....
i tried but nothing
now it's just dead...
i plug in it so maybe it will charge the battery normally but it doesn't seem to to anything. normally there is a led indicator no ?
wuub said:
i tried but nothing
now it's just dead...
i plug in it so maybe it will charge the battery normally but it doesn't seem to to anything. normally there is a led indicator no ?
Click to expand...
Click to collapse
orange led will glow ...when plugged in ....maybe your friend tried to flash android on it but didnt succeed thus causing phone to not charge ...or maybe it is a serios hardware defect ...you can buy replacement motherbrad from here http://www.ebay.com/itm/Mainboard-Motherboard-HTC-hd2-leo-T8585-/260819122167?pt=LH_DefaultDomain_0&hash=item3cba07f7f7#ht_500wt_969 take it to your local repair shop and tell then to replace it ....try this if there ar no more hopes there are cheaper boards avalible too on ebay search...be sure to buy this mbd ...only if your phone is non T-MOBILE
wuub said:
something new happened this morning
I left the phone without battery all night and put the battery in when i got up.
the screen displayed the following message.
/!\ Software update failed. Please Try again.
I couldn't do anything from that point so i pressed the reset button... (didn't want to remove the battery)
phone went off....
as it wasn't responding to anything... i took the battery out and back in.... and brrrrrrrrrrr ... back to scare one
any ideas ? doesnt smell good ...
PS : sorry for double post, hotel connexion in cyprus does really suck.
speed is bad and unstable... they have 150Mb line for the all island (no joke)
cheers
Click to expand...
Click to collapse
Yep it sounds like a bad NAND chip. My guess is it has bad blocks that is keeping it from booting and the steady vibration is being caused by the same. Again just my opinion. I say this because it said, "/!\ Software update failed. Please Try again.", this is common in cases when the NAND went bad.