Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
After (I think) successfully upgrading to WM6, I've had a few problems...
1) I can't seem to soft reset anymore (holding down Power at the top + the reset button)...it seems the only way I can now reset my unit is by physically removing the battery...
2) I can't access the bootloader SERIAL mode...I can access the options for the kernel hive and formatting storage, but no success being able to get into USB mode to reflash my unit
Any help or suggestions would be greatly appreciated - I only bought this phone on Friday
1. This was hard reset in WM2003 - for soft reset just press the reset button
2. You need to press and hold power+reset+record(WMP) buttons at the same time
I suggest you read WIKI first before asking questions which are answered a million times
Thank you for the prompt reply.
I can understand your frustration with many people constantly asking these questions, but please don't make me feel like an idiot when I've actually read the Wiki and tried Googling the problem prior to posting.
To clarify, I know *how* to access the SERIAL option (I had to do it to upgrade from 2003 to WM6 to begin with). My point is that holding Reset+Power+Record doesn't work anymore. It just continues the boot process and goes straight to the Windows Mobile splash screen. The reset button, in and of itself, does nothing at all. I've tried everything from just tapping it a few times to pressing and holding it for upwards of 30 seconds...but it doesn't seem to do anything for me.
Try to hold and press power+record+cam buttons then press reset while holding those buttons.
Yeah, it does nothing...I have a feeling that the actual reset button is no longer working on the unit...not sure if that's to do with the upgrade to WM6, or if it's a hardware problem and just happens to be coincidence :-/
don't take xplode's advise wrongly. it's just that reading AND understanding the WIKI is important especially for beginners like yourself.
if you think you've successfully upgraded to WM6, it's probably because of the "Congratulations" message that was displayed... well, you're almost there, though not quite.
try to fully understand the no/yes/yes instruction in the WIKI... the reset+power+record combination is NOT what you should be doing. it has been replaced by another... here's the thread that could guide you... http://forum.xda-developers.com/showthread.php?t=327978&highlight=kitl
and here's the pertinent wiki page...
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
good luck and welcome to the BA community.
Anyway if this that you try to explain is that the hardware buttons no longer work, you can try the MTTY method, if you have read the wiki you already know what exactly to do
Thanks raymonds, I will try not to, but I just don't want people thinking I'm yet another new member that doesn't read anything before posting, because I know how much I hate that too...I tried reading up on my problems for 4 hours last night before deciding to post because I couldn't find anything else to help.
I have successfully upgraded to WM6 and went through the no/yes/yes steps - the issue is that I want to go back to WM2003 or WM5...they seemed far less problematic for my phone for some reason..one problem I'm facing now is that my BA, pure and simple, no longer recognizes that I have a cellular carrier at all, making it essentially useless as a phone. When I try to go into SIM Manager, it hangs for a while, then goes into the screen saying that only emergency calls can be made...but when I try to put in my PIN, it says "Unknown SIM error", though the SIM works fine in my other phone...
I'm trying to use the Power/Reset/Record to either try reflashing in the hopes that'll resolve my issues, or downgrade...either way, it's not allowing me to do so, and I obviously can't do this while the phone is booted into WM6. It just seems like the reset button is no longer working, since neither combination that uses it (Power+Reset or Power+Camera+Reset) works anymore.
try to downgrade with MAUpgradeUT_NOID.exe, and then reupgrade, another thing you can do is to reflash the radio rom. The MTTY method resets bootloader settings which may be the solution to your problem.
MTTY under Windows XP is explained HERE
xplode, mtty requires one to do the power+reset+record combination, which he currently cannot do.
is this a second-hand unit?
Hm, there was another way to put your device into bootloader mode but i have never tryed it, in most of the WM2003 upgrades there was EnterBL.exe, and when you copy it to the device and execute it the device goes to bootloader mode...
but it also creates problems - read here
Also i had problems in the past with the latest version of MTTY (1.45) and used previous one 1.01 which worked like a charm
Sweet - thanks xplode and raymonds for your time.
Unfortunately I can't try these as I am at work right now, but I do appreciate the suggestions and will try them as soon as I get home.
If I can't get it to work, oh well - off to the service depot and a (probably) expensive lesson learned.
Please keep us updated, about your issue
Thanks guys...
So, I'm taking it that the radio stack is now corrupt, since it's no longer even showing a version number on my BA. I tried the methods xplode suggested - when I enter the unit into KITL mode, I take it I'm supposed to use USB Active as the transport method, since MTTY won't recognize a device otherwise, and my phone just boots into Windows from that point.
When I try to run MTTY though, all it does is display "kITLª" over and over again...I'm not sure if that's normal, or even how to enter a prompt of some kind...
I'm starting to wonder if maybe I should just take it to the depot, pay the $75 I was quoted, and learn my lesson... :-/
Any other suggestions, or am I just totally doing what you suggested wrong?
You do not need to enter KITL because this is used to debug your WM build using Platform builder
Just try to put your device to botloader mode and then use MTTY to instruct the bootloader what to do, or just reflash radio and then new rom
below is an email i sent to faria seeking his help, i also decided to post it on the forum, in cae anyone else has some ideas, and in the event the problem gets solved the information is here for someone else who needs it
"I have a problem that i would really appreciate your advice on.
So i bought a cingular/att 8125 - G3 Wizard - on ebay for $40 the listing described it as having a broken lcd screen, so i bought an lcd as well replaced it and that element of it works fine. I turn it on to see that the dumbass somehow installed a rom with the IPL of 1.01 and the SPL of 3.08.
so im assuming that is the conflict keeping it from booting up properly, i can easily access the boot loader and flash almost any rom available.
my main issue is this, from what i gather, i need to bring the IPL up to at least 2 for it to be compatable, but any rom i try to flash that acctully replaces the ipl gives me , i belive an error 300 and says the updater tool is to old, so do you know any way i can update the IPL so it works.
thank you,
Adam"
Is it CID locked? I saw that message a lot when I had mismatched SPL/IPL and the CID was locked. Try running an older version of lokiwiz, it can unlock that combination (lokiwiz2b couldn't do it, but something from around October last year could).
Then try button ROM or an OEM ROM.
$40 is not bad at all, even with a broken LCD.
thanks you for the response i actully saw that post my self, but becuase of the fact that it doesnt boot beyond the splash screen i cant run active sync to use lokwiz , unless there is a way to run it without active sync and at the bootloader.
thanks though
u could always try a hard reset commanager and voice commander and then press on button and then press send once message comes up
Hi guys, you have been a great help to me so far, but I just can't find anythign to help me with this now. I have a hermes100 with WM6 and i just flashed the radio to 1.54.07 and it gave me an option for hardSPL and said that it was recommended so i investigated and found the upgrade for it.
I ran the wrapper file and it goes to the stage where it puts my hermes into flash mode but it displays "spl1.09" on the screen yet when push the ok and power keys during reset it shows "spl2.03"
it goes through the screens until it puts my phone into flash mode and it says it is trying to read my device then i get error code (260) that it isnt connected. Anyone know a way to fix this?
Use sd card method, page 116 on here: http://forum.xda-developers.com/showthread.php?t=296722
Hope this helps...Cheers...
okay, i tried the sd card method and it does the same thing. after it gets to the bootloader screen i just sits there with
"HERM100
IPL-SSPL by des
HERM 100
SPL-109.ds
serial"
okay, nevermind, i just had to reinstall the drivers for when i was in bootloader mode. I got it to work, thank you for you help.
cheers :-D
No problem, now you should be able to flash any hermes rom to your hearts content with the knowledge you have a safety net if something does(and probably will, as you'll find flashing addictive, sooner or later) go wrong. Pleae remember though that Hard SPL ISN'T a guarantee that you will be able to fix you phone, it just makes it easier when something goes wrong... Cheers....and happy flashing...
samterry1234 said:
okay, nevermind, i just had to reinstall the drivers for when i was in bootloader mode. I got it to work, thank you for you help.
cheers :-D
Click to expand...
Click to collapse
how did you do this?
First of all I am so sorry to bother you all!!!, as I can see from 3 days of non stop reading here and e;sewhere, its not always liked to ask questions, but I am sorry I really need help!
I bought a 8125 cingular from eBay (bought a x01ht but it hasnt arrived)
I have read seriously so much I am now confused! But I have tried to research this 100%
when I got the phone yesterday, I first sim unlocked it with the "All HTC" unlocker.. then I used unlock ext rom wizard, and Likiwiz02 for the cid.. I did see it say "your phone is superCID" unlocked or what ever...
I then tried to flash with x2h_wm 6.5 and it went through the steps like it should and finished and said your rom is updated, BUT when the phone rebooted, it was like it went DOWN not up.. I lost alot of things and now it said G not E for network, I had less signal, and had the roaming Icon. Well, after that My XP computer would no longer recognize the device.. I would plug it in and it would charge, and the active sync tries to connect but after a few minutes it says it can not connect.
I am able to "sometimes" connect top my Vista" device, BUT I have not yet mastered being able to flash a rom with Vista... as I always get RUU is closing, because of error.. and it leaves my phone in bootloader RUU mode, so i have to reset it. I have tried the instructions here http://forum.xda-developers.com/showthread.php?t=291723 and One time I was able to get pretty far without an errors from RUU, but it said I needed a newer version.. or something, and after that I am unable to do it do any RUU on vista, although most of the time I can get it to connect by going to the services- and restarting wm 2003 thing"
This is the details of my device (and yes I know is a G3)
IPL & SPL :2.25
gsn: 02.25.11
os: 2.25.11.1
Ext Rom: 2.25.11.102
Radio: 02.25.11
Rom 2.25.11.1 WWE (build 14928.2.2.0)
protocol ver: 4.1.13.12
My question is.. What am I doing wrong? How can I get either XP to connect, or Vista to run RUU?
Can I flash by sd card.. ( I have seen both yes and no, and am confused on how to do it)
Tweeks I have done is installed a cab to remove roaming icon, reg. changed the G to E for Edge... Speed it up bu changing mem. and I think that's pretty much it!
Scream at me and call me stupid, BUT Please help me.. There are 10000000000000 different HOW TO all over the place, and all are different, and I really just would like a little PERSONAL help from someone..
THANK YOU SO MUCH!!!!!!
Tony
Also.. On the Activesync issue.. I have uninstalled and delete all tracers on my xp laptop and reinstalled both the newest version , and when it did the same, I uninstalled and reinstalled an older version... Still the same!
http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
best thing is to start with reading the wiki
Read it over and over...
I am not just saying it when I say I have searched and searched!
UPDATE
Although I received no answers, I thought I would upddate... I am so embarrassed, as the active sync was an easy fix.. (disable Firewall) I cannot believe it is that simple, as it was working fine before with firewall..
Ok I am following the instructions now flashing with XP button rom, etc etc.. Will follow up later!
Ok progress!
Well, I was able to flash to phone to button rom, and then CID unlock it with lokiwiz, but My IPL and SPL are different. SO i flashed button rom again, and its still the same... Can I go ahead and flash back up, or what do I need to do?
IPL 1.01
SPL 2.25
tlbaker78 said:
Well, I was able to flash to phone to button rom, and then CID unlock it with lokiwiz, but My IPL and SPL are different. SO i flashed button rom again, and its still the same... Can I go ahead and flash back up, or what do I need to do?
IPL 1.01
SPL 2.25
Click to expand...
Click to collapse
If all was successful your good to go.
And yes you can flash back up.
I am so ANGRY... I got to 100 % and my cat hit the cable and Now its stuck in RUU... I am looking for a fix.. ANY HELP PLEASE?
OK... got it going again... flashing back down to button, the only one that would connect.. and I will build my way back up...
Sorry for posting so much.. and thanks for the help!
I have flashed to T mobile 2.26.10.2 , IPL/SDL are both 3.08 And I have tried several times to go beyond WM5.0 but It never loads.. Any advice...
Thanks
Connect the phone to the PC and run Wizard Service Tool and press Enab. RAPI + Unsigned Apps button.
Then press CID Actions Button and Read CID block, this will tell you if your CID unlocked.
Well, I will try that, BUT I am assuming since I have a Tmobile ROM on a ATT phone its no longer unlocked???
When I ran the unlocker it said it was now SuperCID unlocked or whatever..
I will do the Service tools and see.. and Post back soon! THANKS
It is locked!
OK.. I ran the tools and it said it was CID locked... this was the results (not sure if usefull or not)
Checksum : fb67d2a2
CID: WIZCNG01
Its funny because when I ran the other lokiwiz it said it was unlocked..
I tried to unlock it and it said downgrade SPL to 1.06 or less.. AND thats the problem... When I Loaded Button rom the 4 different times I have had to flash it.. THE SPL never changes down.. One time I flashed it, I repeated it 3 times as per some instructions i seen that if you flash it again it will change.. NOPE did not change, the IPL always changes, BUT SPL stays the same.. SO If I flash again, this is the results SPL 3.08 IPL 1.01
Can anyone help me .. maybe use a diffrent rom instead of button?
HELP PLEASE!
THANKS
Have you tried to go back to the original ROM?
Problem solved
I am still tinkering, and adding patches now... BUT I was able to get wm6.5 (VERY SLOW ON MY WIZARD) so I went back to button rom, and installed XDA Mobile 6 Release 5 ROM, and I LOVE IT!!! like I said I am still adding stuff and playing with it, but so far its better than WM6 I have on my Cheetah (treo750)...
I will add the steps I took , and trial and error steps, so other people that are impatient and ask questions like I did, will know what to do.,.. BUT let me play with my new toy for a while!!!
One question.. Should I stay with IPL/SPL 2.26? Or should I go back up to 3.08 or ?????
Thanks