GPRS is new territory for me. I'm planning to apply for a GPRS acct with my telco
I'm afraid that once I've configured the settings for internet via GPRS from my telco, it will always use GPRS whenever I want to connect to the internet.
How do I switch back to normal mode when I'm at home and accessing the internet thru ActiveSync?
On my EXTENDED_ROM, there is a file called vodafone.CAB which will configure my phone with Vodafone settings (I'm with Vodafone). Whenever I run that file (after a hard reset), I cannot access the internet via ActiveSync. Everytime I run PIE, it always defaults to GPRS.
I don't know how to switch to use internet via activesync once I'm on the GPRS plan and then switch back to GPRS when I'm not at home.
If you are concerned about it using GPRS once you are connected to ActiveSync you could always switch to flight mode. Not ideal, I admit, if you use your phone alot and don't like it being turned off.
I had two profiles on mine, one GPRS and one dial up. Even when I set the default to the dial up (CSD) it still tried to use GPRS. Fault with my pocket PC only? maybe. What was strange was that even after I deleted the GPRS profile and soft reset it still was using GPRS! I had to hard reset in the end.
So, I would backup your pocket PC before installing the GPRS profiles.
If you have a large bandwidth then it probably won't matter to you but if not I would definately install a bandwidth monitor as you may also find that some apps you install may also try to periodically get internet access.
The problem with Windows Mobile 2003 is that you can't seem to tell it to ask you first. Microsoft seem to think that you either want GPRS on permanently or don't use it at all. I am sure there are a lot of people out there who just want to use it from time to time. If an app wants internet it just goes and gets it!
Having said that, even with CSD, it will still dial out when it wants. To get around that problem I created 2 profiles, one of which doesn't have a userid and password. I set the default profile to the one without userid. That way if something tries to get internet access it first asks the user to enter their userid and password - in effect it safeguards against a rogue dial out.
I personally don't use GPRS as I found out that my CSD access will use my free minutes. Since I hardly use my phone for voice calls I may as well make use of the free minutes for internet access.
Ok did some searching around ppcsg, apparently you can turn off GRPS by pressing the RED button (the disconnect talk button) and holding it for a few seconds.
Or use this tool
http://www.pocketpcfreeware.com/en/index.php?soft=1123
Question is whether once the GPRS is turned off, will internet access be automatically be directed to the ActiveSync connection (assuming I'm connected via ActiveSync)
To use internet via AS you should configure 'my work network' correctly under the 'connections' settings. The 'my isp' connection is meant for dial-up & gprs access to the internet.
Sadly can't tell how to do it in detail as my magician is my wireless modem & at work the connection isn't allowed. Maybe the help files are of any use in this.
Cheers, M
yes, mine, just automatically uses my internet connection thro' my PC with AS, but as soon as I disconnect from my PC, my Qtek switches over to GPRS.. which is pretty cool.
dood, care to share how you achieve this?
I suppose the question is, if you are connected to a PC which is on the internet, why would you want internet access on the Magician anyway? Why not just use Thunderbird or other web browser?
Outlook will sync the inbox for e-mail when connected via activesync...
The joy of surfing the net while watching TV lying on the bed..can't really do that wth a laptop..too heavy
Hi folks
Been playing with my new O2 XDA II exec toy for a couple of days now and came across this forum.
I have a question;
I can connect fine with wireless, but if I either switch off wireless, or start Opera/Internet Explorer without any internet connection, the phone automatically tries to dial the GPRS connection number. This is annoying and I'd want the phone to do nothing or give an error if there is no internet connecttion available. How do I change this in the settings?
The only way to stop the OS from dialing a gprs or dial-up connection is to have none of them configured in the connection settings. Sometimes you even need to hard-reset to get rid of them as your device still 'remembers' the settings & connects the gprs while you have deleted all connections.
Regards, M
Can you untick the remember username and password box? Thats what I have done, and if it does try to connect it wond go past that.
Eeeeh,
my gprs ain't using user/password. R u referring dial-up?
Cheers, M
I just make a spoof GPRS connection called VJSpoof, with no details in it.
Select this one when you want to disable GPRS, or go back to the normal one went you want to use GPRS. I use this when reading news on NewsReader offline, because otherwise it tries to connect up to download pictures.
V
oltp said:
Eeeeh,
my gprs ain't using user/password. R u referring dial-up?
Cheers, M
Click to expand...
Click to collapse
On my GPRS I have a username and password box, although nothing needs to be entered in it. I make sure the box which says Always Remember These Details is unticked.
haha vijay... I like your thinking... works a treat, just remember to manually select them, and not have it autopick tries to dial out, then error
Many of you on this bb has a problem that GPRS doesn't re-connect and you have to reset or turn flight mode on/off to get connected again.
Here is what I did and mine has now been working for 3-4 weeks as it should be working. Shows to me that none of the software like Wisbar, Pocket Plus etc is causing it.
In SETTINGS/CONNECTIONS, under CONNECTIONS I have My ISP and My Work Network. Under both I used to have WAP, where it will use GPRS to connect. I have deleted the WAP GPRS option under My Work Network, to have nothing under Modem Connection, I only have WAP GPRS under My ISP in the Modem Connection.
Also, I used to have my work's settings in VPN, which I have also taken out. When I activesync via GPRS, my phone used to connect to the GPRS server and then tried to connect to VPN. After that I couldn't re-connect with GPRS.
After I have done the above, my phone now connects flawlessly everytime using the actievsync mobile schedule and when connecting manually.
O yes, I also run GB-Soft's GPRS tweak which can be found at http://www.GB-Soft.cz/XDAII
Well I was very sceptical about this. But I too deleted the WAP settings under Work and in the last month I haven't been unable to connect once.
So either this works or O2 have solved a problem with their network (I did not have the problem last winter in Singapore, Malaysia, or Australia iirc.)
The only other difference to my setup is that I now use Activesync 4.2 rather than 3.x
I am on Vodacom in South Africa, and what I have done above works for me. I only reboot my phone now to clear memory to free up some or when I need to run my GPS software, then I reboot to give it as much memory as possible.
I posted a solution that works for me, use, don't use it, up to you.
Hey, I was saying thanks - I believe it works
kevino said:
Well I was very sceptical about this. But I too deleted the WAP settings under Work and in the last month I haven't been unable to connect once.
Click to expand...
Click to collapse
Sorry, my mistake, this part was confusing, as it looks like you couldn't connect.
Yes,
"I have always been able to connect first time" would have been a lot better than the double negative :lol:
Hi
I apologise in advance because I'm sure my problem is simply solved but I;ve not used the XDa for a while and I'm back to square 1. I have tried searching for the anser but I think my question is just to basic.
My XDA2 is unlocked and I use a T-Mobile sim in it. The problem I have is with the TOMTOM. When i try to update traffic info on the fly I get a message saying modem hung up (or something similar). It works fine when connecting via the cradle and my PC.
Now I think this is because the XDA2 is trying to connect using the O2 settings when I am on the road.
So my question is how do enter and then I get the XDA2 to use the T-Mobile settings?
EDIT: Sorry forgot to say so far I have done the following:
Start
settings
connections
Add new modem connection
enrtered T-Mobile
selected cellular line (GPRS)
entered access point as general.t-mobile.uk
user name as user
password as wap
Ok and update
seems it is connecting after all. Problem is I have to connect via GPRS first then up date the traffic. It's not picking up the connection if I just update direct from TomTom
any ideas?
I don't think you can do much about that, cause the tomtom, must automatically try to establish the GPRS connection.. like Internet Explorer does, it automatically checks if you have GPRS or Wi-fi connection, if not connected for you automatically. after reading your post. it does not start your GPRS connection, have you look into the settings of the tomtom, to see if he has an option that you can let it connect through your GPRS automatically?
Questions for people using the blackberry connect software:
I want to sign up for cingular's blackberry service, especially since I am overseas more often than not for work.
(Some of these are questions, some are assumptions. just trying to get some info )
My question(s) are:
1) Blackberry connect acts as your internet connection, right?
2) Does anyone use it and get a UMTS connection instead of GPRS?
3) Does your hermes act like it has a normal connection? (in other words, if I turn on Blackberry connect, can I use other progs which use that net connection - say Flexmail 2007 or IE or somesuch)
4) Does the blackberry stuff use the existing calendar /addressbook programs on the hermes, or does it use it's own? (assuming it's own)
Thanks for the help. Wondering if I can sign up for the blackberry service and basically get a flat fee rate on data when I am in Europe, etc.
derrumbe said:
Questions for people using the blackberry connect software:
I want to sign up for cingular's blackberry service, especially since I am overseas more often than not for work.
(Some of these are questions, some are assumptions. just trying to get some info )
My question(s) are:
1) Blackberry connect acts as your internet connection, right?
2) Does anyone use it and get a UMTS connection instead of GPRS?
3) Does your hermes act like it has a normal connection? (in other words, if I turn on Blackberry connect, can I use other progs which use that net connection - say Flexmail 2007 or IE or somesuch)
4) Does the blackberry stuff use the existing calendar /addressbook programs on the hermes, or does it use it's own? (assuming it's own)
Thanks for the help. Wondering if I can sign up for the blackberry service and basically get a flat fee rate on data when I am in Europe, etc.
Click to expand...
Click to collapse
1. BB Connect uses your internet connection.
2. BB Connect only connects while under a GPRS/GSM/EDGE connection. In other words, you will need to force your connection or while in a GPRS area to use GSM only. You can do this within the connection Band settings.
3. You can use the internet connection from any program while BB Connect is running. However, Since BB Connect is a lower priority connection, applications like pIE, etc. will take a higher priority over BB Connect and force the BB Connect client to idle while it waits for the connection. This is an automatic process.
4. BB Connect will uses the built in PIM applications (Pocket Outlook, etc.)
Cingular has a few Blackberry plans including a unlimited plan.
thanks for the response.
So that doesn't sound as good as I was hoping.
I was hoping that Blackberry would be a conduit for the rest of my applications to use, instead of being one of many apps using one network connection.
So much for cost savings and/or surfing the net via blackberry connect.
derrumbe said:
thanks for the response.
So that doesn't sound as good as I was hoping.
I was hoping that Blackberry would be a conduit for the rest of my applications to use, instead of being one of many apps using one network connection.
So much for cost savings and/or surfing the net via blackberry connect.
Click to expand...
Click to collapse
I am assuming I understand your connection question. BB Connect is no different then other applications that use a internet connection. BB Connect uses the internet connection to connect and pull down mail. Other apps don't use BB Connect to get a connection. If you have a BB plan, that will allow you to have a connection not only for email, but for any app (i.e. Internet Explorer)
hmmm... interesting point.
What you are saying is that from cing's point of view, my device would be a "blackberry" although it would actually be a hermes.
What I would have to figure out is if cingular filters out connections so that you can only connect to the blackberry server....
derrumbe said:
hmmm... interesting point.
What you are saying is that from cing's point of view, my device would be a "blackberry" although it would actually be a hermes.
What I would have to figure out is if cingular filters out connections so that you can only connect to the blackberry server....
Click to expand...
Click to collapse
That's correct. Cingular has no idea nor cares what device you are using. They actually sell devices like the Nokia E62 (BB Connect preinstalled) and Treo 650 which has the BB Connect software available for download.
brmcguire said:
1. BB Connect uses your internet connection.
2. BB Connect only connects while under a GPRS/GSM/EDGE connection. In other words, you will need to force your connection or while in a GPRS area to use GSM only. You can do this within the connection Band settings.
Click to expand...
Click to collapse
Interesting, so BB Connect or the BB network is not compatible with UMTS? What are the symptoms BB Connect displays when UMTS is active?
I played around with this yesterday on cingular USA, but could not get the Connect software to connect, instead it would say network available then fall back to "suspended by user". BIS account creation wouldn't recognize my PIN&IMEI combo.
Thought this was a show stopper, but perhaps it's not.
Thanks
yeah, it only works with GSM - you have to force the band away from utms.
if you go over on howard forums and look in the cingular section, you can find info - I think that I saw that error mentioned....
mooney6023 said:
Interesting, so BB Connect or the BB network is not compatible with UMTS? What are the symptoms BB Connect displays when UMTS is active?
I played around with this yesterday on cingular USA, but could not get the Connect software to connect, instead it would say network available then fall back to "suspended by user". BIS account creation wouldn't recognize my PIN&IMEI combo.
Thought this was a show stopper, but perhaps it's not.
Thanks
Click to expand...
Click to collapse
When BB Connect is fully connected to the BES/BIS it will display 4 dots. For some reason, and I don't know why is that the BB Connect client doesn't like a UMTS connection. It might have todo with how GPRS/GSM holds a connection. Here is a handy link for connection status indications.
As far as the BIS registration, you will need to create a NEW account on the Cingular BIS site. Then you will be able to register your device and BB Connect.
http://www.dopodasia.com/resource/sea/bbc_web/connection.html
derrumbe said:
3) Does your hermes act like it has a normal connection? (in other words, if I turn on Blackberry connect, can I use other progs which use that net connection - say Flexmail 2007 or IE or somesuch)
Click to expand...
Click to collapse
No personal experience, but folks on HoFo say BB Connect is killing the internet connection for other programs like PIE:
http://www.howardforums.com/showthread.php?t=1044755
Richard
rsolomon said:
No personal experience, but folks on HoFo say BB Connect is killing the internet connection for other programs like PIE:
http://www.howardforums.com/showthread.php?t=1044755
Richard
Click to expand...
Click to collapse
Hi there, sorry to be so unspecific, but at least I wanted to share my experience
German O2 XDA/HERMES recent, used in Belgium with a Company BB service from Proximus, using BB connect 2.16 usually via UMTS, but when roaming also via GPRS; never forced it to GSM.
It is very slow! so you need to be patient; 1 min waiting until everything has re-connected is not unusual.
I remember that I had the same issue of BB Connect monopolizing the internet connection so that Skype not even started and IE was not able to connect to the internet neither.
After a cold reset and re-installation of everything it works now to expectations:
BB C is usually always on and on UMTS
When starting IE, a pop up apprears saying, connecting to ...
that's when BBC goes 'offline' Symbol :!
I can then surf the Internet
You must TERMINATE IE, not just leave it running in the background
After some time, BBC will automatically re-connect. If you try to speed up, it will complain that the connection is still blocked by another program.
I believe that BB C creates another hidden connection which is not visible in the connection folder, but if you use fit4cat, there is a tweak for 'force connection always on' and there I can see Blackberry as connection
I did not notice any handling difference between UMTS or GPRS.
HOWEVER
I have another problem as following:
I carefully checked the BB C services, but I cannot get any synchronisation of deleted mails, neither when I deletem them on the Desktop, nor when I deleted them on the Mobile.
Any experience with that ??
Rgds
hk.
I'm using BB Connect with a Vario II on TMUK.
When BB Service is on, I am connected through the blackberry.net APN, but via UMTS. If I want to browse, check POP3 email or do anything else, I have to be connected through the TMUK Internet Access Point, which is how I access Web 'N Walk and my unlimited data allowance. This, of course, interrupts my BB connection.
I believe it should be possible to use the blackberry.net APN for web-surfing as well because on RIM devices, all data goes through the BB APN. However, if I try to manually set up a new connection with the blackberry.net APN and route data traffic through it, it doesn't work.
So, not quite sure, but it should be possible to use the blackberry bundle on whatever network as the conduit for data traffic that one of the posters here was referring to - might just need a chat with tech support at your network.
Dave
other post says BBC does not support MDS, so you cannot surf using blackberry.net (not sure what MDS is, but guess it is in a real BB)
also can confirm that I have to suspend the Blackberry GPRS/EDGE connection before IE and POP3 mail will work - both GPRS connections (Blackberry and normal GPRS) are active, but the Blasckberry one seems to have priority
using HTC P3300 and TMO BBC client 2.1.2.31
ive been using BBConnect on both the XDA Exec and the V1605 for well over a year, it will connect to the BB Server using whatever PHONE network band is available e.g. UMTS if in a good Vodafone signal area or it will step back to GPRS if it doesnt, there are issues when roaming on other networks which will not pass through the BB connection so for example when in Germany on a supposed Roaming Partners network BB doesnt connect. I just have to force the Phone to try to connect to VF which then obviously works albeit a low speed connection. as for using PIE whenever I try to connect it disconnects the BB Connection and connects again using the VF connection, I agree this is a bit @rse as you would have thought the applicaitons could see that there is a usable connection there and should therefore utilise it..
If anyone knows of a registry setting that can be modified to fix the connection hopping I would be interested.
Problem with BB C on Tytn
Hi, I downloaded the BB c software from Voda.de, and installed it onto my Tytn with WM5. the instalation and registering to the network was fine.
but I cant do e-mail set up... it's grayed out and I cant click it...
I also tried registering/creating an account through mobileemail.vodafone.net,
but to no avail. after I input IMEI and PIN, then create Usename and password, I get the notice, "The system has encounted an error".
I thought I might have wrong software, and to keep things simple I put WM6(Official rom from HTC) into handset, then put BB C 4 for WM6, (again from Voda.de) but to no avail. same situation.
the phone connects to BB GPRS/3G, it shows PIN, IMEI, IP.
so connection wise there doesn't seem to be problem.
but cant create an account...
anyone come across same problem??
I've been trying to figgure this out for like three days now.
Thanks to those who'll give me advice!!
BR
Timmy-Boy
Timmy-Boy said:
Hi, I downloaded the BB c software from Voda.de, and installed it onto my Tytn with WM5. the instalation and registering to the network was fine.
but I cant do e-mail set up... it's grayed out and I cant click it...
I also tried registering/creating an account through mobileemail.vodafone.net,
but to no avail. after I input IMEI and PIN, then create Usename and password, I get the notice, "The system has encounted an error".
I thought I might have wrong software, and to keep things simple I put WM6(Official rom from HTC) into handset, then put BB C 4 for WM6, (again from Voda.de) but to no avail. same situation.
the phone connects to BB GPRS/3G, it shows PIN, IMEI, IP.
so connection wise there doesn't seem to be problem.
but cant create an account...
anyone come across same problem??
I've been trying to figgure this out for like three days now.
Thanks to those who'll give me advice!!
BR
Timmy-Boy
Click to expand...
Click to collapse
try this....
1) Change device ID, from Start -> Settings -> System -> About -> Device ID to HTC_TyTN
2) Edit your registry: HKLM\System\Versions\AKU key, change the key from (1.0.0) or whatever in there to .0.4.2
lve0200 said:
I have another problem as following:
I carefully checked the BB C services, but I cannot get any synchronisation of deleted mails, neither when I deletem them on the Desktop, nor when I deleted them on the Mobile.
Any experience with that ??
Rgds
hk.
Click to expand...
Click to collapse
As he mentioned above I have the same problem. For regular Blackberry devices they give the advice to check the options on the messaging screen and there is setting to choose delete on handheld, both, or prompt, But I could not find any such setting in the BB client for WM6.1
BB Client is 4.0.0.97, desktop software is 4.0.0.18
Any advices?
!!! SOLVED !!!
1. Tap Start > Settings.
2. Tap the System tab.
3. Tap the BlackBerry icon.
4. Tap the Services tab.
5. Tap the BlackBerry [CMIME] service book
6. Tap the Synchronization tab.
7. Select the Enable Wireless Synchronization check box.
8. From the Conflicts drop‐down list, tap an option.
9. From the Delete on drop-down list, tap an option.