Guys few hours ago i try to upgrade the firmware of my XDAII, haflway it stuck. After that i try to reset it, what i got is a hang screen, i can't go into my xda. Luckily i save the rom into my SD CARD(using the D2S command) .My question is what is a command should i use to restore back my rom from SD to XDAII. - I need it badly..
Thanks Guys.
if flashing a new rom doesn't help, you might want to take it to a technitian.
Related
HI everyone,
when i was instaling a new rom for my universal, it stoped at one time, now the phone doesnt work , i just can see on the top of screen USB and v1.01,
and when i push the 2 bottoms and reset for restore to factory default the white window appears till i click on 0 then nothing
please help
Thank you
which ROM were U trying to install?'Cos some of them needs never bootloader. is somewhere on ftp. Try other methods to make it running i.e. somwhere on wiki is tuto with some direct commands. Try reflash with original rom. Use search
try those links:
http://wiki.xda-developers.com/index.php?pagename=Instructions%20for%20those%20stuck%20on%20Boot%20Screen
http://wiki.xda-developers.com/index.php?pagename=Instructions%20for%20those%20stuck%20on%20Boot%20Screen%20%28UNI_exitbootloader%29
http://wiki.xda-developers.com/index.php?pagename=Upgrade%20bootloader%20from%201.00%20to%201.01
Had the same problem a couple months ago.
Just put it into bootloader (power+light+reset).
And flash the (original) rom again.
Worked for me.
Good luck.
... and take out the SD-Card. This happened twice to me until I took out the SD-Card. In my opinion, the mobile will see an inserted SD-Card as ExtRom when you do a hard reset.
As far as there are no cabs on the card, nothing will be installed !
tsfnet
I had a similar problem. Just repeated the process with the original cable and everything worked fine. Some replacement cables do give problems.
I am afraid my Polaris bricked, but I hope somebody knows a solution. Let me explain:
I turned off my device to get my microsd card out. I put the card in my cardreader to fill it with a lot of music. After that I inserted the card in the polaris, turned on the pda, and I got into the bootloader screen .
I tried to soft reset: bootloader screen again, tried to hard reset: bootloader, tried to flash original rom: rom update complete and after that bootloader, tried to flash several cooked roms: rom update complete and again the bootloader. When I try to charge my polaris it automatically turns on and goes to the bootloader. Flashing with microsd doesn't work. I also tried the thing with mtty, but it doesn't show the usb option in the list...
I DID hard-spl, I was using udk diamond R8 and never had any trouble before, while flashing about once a 2 months. I really am desperate, because I am unable to charge the pda now. I searched well and I only found threads of people who forgot to hard-spl before flashing custom roms.
I hope someone comes up with a brilliant idea, I love my Polaris way too much working and I don't want it to be a nice looking pda that doesn't work anymore.
PLEASE HELP!
I now manage to get into the mtty application, but I don't know if it is a good idea to use it. The problems I found here which could be solved with mtty are different from my problem I think. What would be wise to do? I flashed various original roms, and radios. That seems to work as normal, but after flashing I keep returning in the bootloader screen .
I hope one of you has an idea what to do. If it is something that is involving risk, I think I should do it anyway, because in this current state my Polaris is useless.
a few ideas! maybe they can help!
1) do you have warranty? you can restore back to original spl and then get HTC to ix it!
2) Try flashing your phone without the MicroSD card in place, maybe with the stock HTC Rom
Another option - try to delete all files from your memory card.
Thanks for the replies.
1) do you have warranty? you can restore back to original spl and then get HTC to ix it!
I read the thread about restoring back to original spl. There is stated that you can't restore to original spl if you are stuck in bootloader...
2) Try flashing your phone without the MicroSD card in place, maybe with the stock HTC Rom
I tried a lot of times, but every time after flashing has finished, I return to the bootloader
Another option - try to delete all files from your memory card.
I formatted my memory card in fat32, tried to flash with sd-card. When I turn on the phone it shows about 0.5 seconds something like "no rom image" and returns to bootloader screen
My cruise is still stuck, and I really think about trying things in mtty as a last resort... Anybody who knows what commands I should give in mtty in this situation? All help is appreciated, and if a suggestion makes my polaris work again I will donate the brilliant xda-member 20 euro's!
I have the same fault and have not found a solution. Every time I soft reset I am stuck in the boot loader screen. If I switch off the phone using comm manager then soft reset the phone will boot okay.
The only method I have found to be able to boot properly is to leave the battery out overnight and then start the phone in the morning. Always boots without a problem this way.
To make matters worse the USB port on my phone is broken...
Hi,
I'm kind of new around here.
My problem is as follows:
- TyTN running PaysRom for about 9 months
- Started to get very sluggish
- Unable to get signal
When i booted my HTC the 'R' and 'G' that appear on screen and used to have values in front of it now display 'none'.
So, I connected it to my PC, 'activesynced' it and tryed to install a new ROM, hoping it would solve the problem.
But the new ROM wasn't installed sucessfully and now all I got is a brick.
I can't even connect it to ActiveSync since it's not recognized.
Is there any solution to my problem?
TIA,
hype
Can you get to the Bootloader?
Yes..
By pressing the Ok+Power+Reset on the bottom button, I see the 'RGB'+white thingie, that I believe is the bootloader..
What SPL do you have? Is it Hard SPL V7(2.10)?
If it is, use the sd card method to install a new ROM.
remember to backup your card 1st.
1. Format 2Gb or less sd card FAT32. Copy .nbh file of the ROM you want onto it and rename to hermimg.nbh .
2. Insert card into Hermes and reset into bootloader.
3. If all things have been done right, follow the prompts....
If the radio ROM has died, I'd suggest trying to flash the Shipped Stock ROM 1st and see if that actually fixes the problem with the blank values on R & G. WM06 upgrade of shipped carrier ROM should also work.
Cheers...
Tks for your response.
I tryed the SD Card method already, with no sucess.
The red stripe shows as follows:
Code:
HERM200
IPL-1.04
HERM200
SPL-2.03
Everytime I tryed on another ROM I always perfomed it using SafeSPL.
Since I don't have 2.1, what can I do?
Tks for all ur help.
What happens when you try and flash a ROM over?
Do you get any kind of error?
You need to find the SHIPPED STOCK ROM. WM06 upgrade should be OK as the CID should match.
Put Hermes into bootloader and connect to PC after unticking "Allow USB Connections" in Activesyncs settings on the PC.
Run the RUU_Wrapper.exe file of the SHIPPED STOCK ROM. ven though activesync won't etect it, the flash file should. Follow the prompts.
Good luck as this seems to be the only way to fix this.
Good Luck...
You might be able to flash a Stock WM5 ROM using the SD Card method. Worked for me when I had SPL 2.03. In fact that's the only ROM it would let me flash over when mine bricked.
Can anyone help me?
I was flashing back to stock SPL, using sd card, and pulled the sd card out while it was flashing (don't ask, I seemed to forget for a moment what I was doing and realized I needed my card for my other phone) Now, I have the stock SPL, shows PANT200 SPL-0.36.0000 CPLD-2 when phone starts, and says "Upgrade ROM code error Please Try Again". But, if I put my sd card in it with PANTIMG.nbh SPL file, then I get a screen that says "Loading...". And that's it, left it like that forever it seems and no change.
Any idea? It won't connect to the computer so I can't flash from computer. Even QPST won't find it.
FWIW: I do kinda know what I am doing. Unlocked mine and wife's Treo Pros with Cmonex hard spl, and flashed several ROMs, including a couple I cooked with NightRaven's kitchen. I was just going back to stock cause my wife doesn't like changes, and now this happened.
TIA,
Malachi
OK, thanks to cmonex I got this working again. Had to connect to mtty and run: set 16 0.
Did that and soft reset, and Voila! my Pro works again..
Thanks Cmonex!!!!
Out of curiosity:
I need to revert to the original stock spl as well. Have not found a way yet...Could you offer me some guidance.
Thanks.
hi anyone pls help,
i have one imate jasjam, the initial problem is i done a hard reset and the phone reboot and it wont finish running the customise application installation, after that the phone cant detect network, i had run a hard spl into the phone and then try to flash a rom that i download from forum but it only run 11% then stop then i realise that the rom i flash is for htc jasjam not imate jasjam, now my phone can only stay at the boot loader mode, i also try different rom but no luck so i think i ask for your help
here is my device details at the boot loader mode
IPL-1.04
SPL-2.10.01ipro
before i flash it i also cant find any radio rom version in this phone so i guess the radio rom also missing or what just not sure....
i think i flash the htc jasjam wrong model rom even now i flash back the original JASJAM_WWE_1.20.305.3_1.20.305.104_1.07.03.10_ship this error message come out "ERROR [260]: update error" and it ask me to check my usb connection.
i search the forum and few member advice me to use mtty and i did tried that many time it didnt work, another member advice me to use this method "Formate yr memorycard & Unzip attached file in your memorycard named Hermimg.nbh & put yr cell in boot mode & follow screen instructions..........this illl boot yr celll out to boot mode......... " i tried that but the phone always stay at boot mode and no other instructions came out at all so im really lost and just hoping somebody can help me solve this problem...
can anyone pls guide me step by step of how to flash this phone back to normal, your help is much appreciated, many thanks.
Hi, i had the same problem flashing from the SD card. Are you using Vista or Windows7? I tried with Vista Format card, drag and drop renamed image onto sd card. Stuck it in the phone, reset and like you say hangs on bootloader. Then i tried the same thing from my Windows XP laptop, exactly the same format, rename drag and drop and everything works fine. Hope this helps
first i tried with vista then i tried with xp the problem still there, any other idea to solve this problem? thanks anyway for your advice
roms?
G'day, I've only really been reading about roms and these phones for only a few hours but I'm pretty sure that htc jasjam and imate jasjam are one and the same phone i think the said rom are used with all hermes type phones..
thanks and sorry for my ignorance if i'm mistaken