Related
hello again folks ...
want to say thanks again for all the help so far .. upgrade went well ..
i went from :
rom version: 3.14.17 ENG
rom date: 10/11/02
radio version : 4.17
to the upgrade :
rom version: 3.17.03 ENG
rom date: 5/15/03
radio version : 4.17
courtesy of www.yorch.net 8)
it was fairly painless ... however the phone still can not pick up a signal ..
also note with upgrade i have been able to switch GSM band from 900/1800 to 900 or 1900 successfully.. but, still can not find t-mobile US as a default setting ...
perhaps i should have cooked and installed one of the following upgrades ? :?
4.00.10 ENG T-Mobile US
or
4.00.16 ENG T-Mobile US
i was hesitant because it indicates once the above mentioned ROM is installed you can not switch to any other ROM using programme A .
my device model no. PW10A1
does this apply to me?
or perhaps i need to udate the radio stack ?? any direction would be great .. thanks again folks !
jason
use 4.00.16 ENG T-Mobile US then once loaded onto xda go into the bootloader (hold power button down while soft restting) then press the calendar (right hand) button and set it to 900/1900mhz
then wait for it to do what it has to do then softreset again.....
then load the phone up with sim in go into phone then options and click on the band tab and select 1900mhz
softrest after if it doesnt pick up signal after then the aversions are not kinda tri band but if it does post up then we will know the answer for deffinate thing is though the radio version is built for 900/1800 not 900/1900 so i dont think itll work but you can try
my device model no. PW10A1
does this apply to me?
Click to expand...
Click to collapse
If the H/W of the device is A type then it's 900/1800. So, unless you have a 900 MHz signal it will not work. Switching the band from phone settings will have no effect unless with proper H/W and RSU version.
ok fellas ...
i went from :
rom version: 3.17.03 ENG
rom date: 5/15/03
radio version : 4.17
to the upgrade :
rom version: 4.00.16 ENG T-Mobile US
rom date: 7/10/03
radio version : 4.17.00
courtesy of www.yorch.net
however the phone still can not pick up a signal ..
with upgrade i have not been able to switch GSM band from 900/1800 to 900 or 1900 successfully through the wallaby bootloader (after changes are made i can not get out of bootloader without doing a hard reset) :? also note the xda developers band switch tool is also present but reads error :?
also note :!:
before the upgrade
my device model no. PW10A1
after upgrade
my device model no. PW10B1
not sure if im getting any closer to the solution but im still happy at this point i havent burned up the unit ...
perhaps it is still an issue of the radio version 4.17.00 (which is the only thing i havent fooled with yet)
any thoughts on trying the radio upgrades from www.yorch.net (under upgrades) ??
if this doesnt kill me it will surely make me stronger ... i will throw a party with beer for everyone if we can get this turkey running !!
thanks again folks !
If you can read a B type on your device that means your H/W supports 900/1900 MHz. To be more sure, check the avaialble options at the GSM menu from the boot loader (Power + soft reset then Calendar button).
If it does have the 1900 MHz option, I would recommend to go for a full upgrade using the latest TMO ROM 4.01.00. It contains RSU 6.24.01 and it works perfectly well for me tho I have 900/1800 network.
Here is the link: ftp://tmobile:[email protected]:21
Be careful and good luck ...
It may be important to note at this point that the OS ROM version really doesn't have much to do with whether or not the phone gets a signal. XDA I is either 900/1800 (PW10A) or 900/1900 (PW10B). (Please note that this model number should be taken from the sticker on the back, not from what the OS says it is.)
If you have a 900/1800 phone, it will not do 900/1900, and vice-versa. Exceptions are said to exist, probably in places where a 1900 provider is really low in the band (or an 1800 provider really high), but this is not recommended and unlikely to work very well.
Band switching is done manually with an extra tab in the Phone Options page between 900 and 1900 in US ROMs, or automatically between 900/1800 in all others. There is also a band-switch in the bootloader, which always offers all possibilities (900, 1900, and 900/1800). After selecting the correct band for your phone, you may need to hard-reset with the SIM removed a few times before the phone 'understands' it is to use another band.
If you want a tri-band phone, get an XDA II. The XDA II by the way comes with vastly improved radio performance. Unlike the original XDA, I can use it in areas with not-so-great coverage.
>any thoughts on trying the radio upgrades from www.yorch.net (under >upgrades) ??
Yeap you're needed of a Radio Stack upgrade, as you have seen 4.17 won't work in the US. So I suggest you upgrade to the AT&T or the T-Mobile stack.
HTH
ROM: 4.01.00 ENG
Radio: 6.24.01
i would love to try this upgrade ...
can anyone tell me where i could download it? :?
thanks
Go to www.yorch.net you'll find it in the upgrades portion of the site
Peter Poelman wrote
There is also a band-switch in the bootloader, which always offers all possibilities (900, 1900, and 900/1800)
Click to expand...
Click to collapse
Thx Peter Poelman so much for this great info, but my original Qtek 1010 never showed the 1900 Mhz option in the boot loader menu and it was PW10A.
Now as I replaced the main board with a one taken from a used TMO device it shows the 1900 option both in the GSM menu and in the phone settings in ROM (I 'm using 4.01.00 now) and the device type is PW10B
Does that mean that the GSM menu shows only what the device H/W can actually support, or it's part of the RSU file contents which may give a fake option of the 1900 MHz ?
Thanks again for correcting our info
saqibj said:
Go to www.yorch.net you'll find it in the upgrades portion of the site
Click to expand...
Click to collapse
You can also get it via FTP at:
Host address: 130.39.48.102
Port: 21
Login: tmobile
Password: rom
HTH
thanks for the info ...
i cant seem to get to this site successfully ... perhaps im going about it all wrong ... any chance you could spoon feed it to me .. ?
Biso007 said:
Does that mean that the GSM menu shows only what the device H/W can actually support, or it's part of the RSU file contents which may give a fake option of the 1900 MHz ?
Click to expand...
Click to collapse
The sticker on the back (and nothing else) tells it all:
PW10A = 900/1800
PW10B = 900/1900
is this upgrade available from yorch ? if so ... where ..?? cant find it anywhere on the site ..
thanks
eurowerks said:
thanks for the info ...
i cant seem to get to this site successfully ... perhaps im going about it all wrong ... any chance you could spoon feed it to me .. ?
Click to expand...
Click to collapse
You need to use a program like CuteFTP or WS_FTP LE
CuteFTP can be found at:
http://www.cuteftp.com/downloads/cuteftp.asp
WS_FTP LE can be found at:
http://www.ftpplanet.com/download.htm
HTH
XDA developer Peter Poelman said:
Biso007 said:
Does that mean that the GSM menu shows only what the device H/W can actually support, or it's part of the RSU file contents which may give a fake option of the 1900 MHz ?
Click to expand...
Click to collapse
The sticker on the back (and nothing else) tells it all:
PW10A = 900/1800
PW10B = 900/1900
Click to expand...
Click to collapse
also note ... unit is an o2 from singapore .. i am in the US trying to access the Tmobile network ... originally it was PW10A .. after the second rom upgrade .. it switched to PW10B ... and also appears to have all 3 bands available from the bootloader .. after 3rd upgrade/downgrade to
rom 4.01.00 eng
radio 6.24.01
still appears to be PW10B1
it is searching for a signal
thoughts anyone? :?
It might be your SIM card so try it in another phone and if it works.
HTH
hello i have an big problem my wallaby dont connect to the phone network so i can't use the phone
please can someone help me i live in the netherlands my operator is tmobile
my rom version is 4.01.16 ENG
rom date 02.04.04
radio version 6.24.00
protocol version 324e4
is this wrong??
please help
greeting cor
Try entering bootloader, power switch held down while pushing stylus in reset, then push the button below the antenna, then choose 900/1800. You will need to do a backup first.
Your rom versions show that it is PW10B1 version (north american version GSM 900/1900).
If your local SP provides GSM 900 service, switch the band to GSM 900 (Setting > phone > Band > choose GSM 900
i have set the gsm band to 900 but it won't help he is stil searching for network
does someone have another solution???
There is another possibility, your phone is PW10A1, but the firmware and radio stack had been "upgraded" to PW10B1. So you won’t get any signal.
Check the label on back to see it is PW10B1 or PW10A1.
yes you are right that is it but where can i find the good stuff
so i must change my hardware version to pw10a1
any idea how i can change that??
now i have tries to update it via asimagetools
but i get a message
itsdcardinfo:niet nader omschreven fout
error opening target device
please can someone help me
civiccoupe said:
so i must change my hardware version to pw10a1
any idea how i can change that??
Click to expand...
Click to collapse
Buy a new device (PW10A)....
No ohter way to change hardware......
Stefan
you need change radio stack back to PW10A, but risky
so i cannot set it back to PW10A ?????
civiccoupe said:
so i cannot set it back to PW10A ?????
Click to expand...
Click to collapse
you can flash the radio stack back to PW10A
civiccoupe said:
so i cannot set it back to PW10A1 ?????
Click to expand...
Click to collapse
Well, my device is PW10A1, but when i had T-Mobile 4.01.16 rom on my xda, it said PW10B1. Therefore check the back of your xda, if it says PW10A1 then you HAVE that version, just the rom says not. hehe. About flashing: you can not use programme a to flash your XDA when you have an T-mobile rom on it; you can only flash it with the SD-card method (use forum search). Try to flash in an 4.01.12 version (O2), i found it better than the T-mobile one.
massage for cgigate and stefan
Hello all,
I have a XDA i have a problem with the radio stack, Frend of mine did and upgrade of Rom and Radio, and he did a PW10B1 radio upgrade is there any posibbileties to downgradit to PW10A1.
Thanks in advanced
hello everyone! im AL from philippines. it's nice to be here. anyway, i want to thank the people responsible for this site...it did actually help me before.
well, i have an xda wallaby. my brother-in-law gave this to me as a present when he came home from U.S. and during that time, the device was sim-locked to T-Mobile. I accidentally clicked something and voila!, I was here downloading the sim unlocking software. It eventually worked but after using for a couple of months, the device just bugged. My phone can no longer find a signal. I tried to re-install the software which I downloaded and still, the problem persist. As for the other apps, I ahve no problem though.
Here are the details of of xda:
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.02
Protocol version : 324e4
Model Number : PW10A1
by the way, i also opted to change the ROM version.
PEEPS, can you please help me on this. I am planning to bring this device next month to UAE. Thanks a lot and i would appreciate for a quick reply.
Again, thank you everyone! Cheers!
alraf said:
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.02
Protocol version : 324e4
Model Number : PW10A1
Click to expand...
Click to collapse
Are you sure about this? Radio Version 6.xx are for PW10B models. Please check the rear sticker of the device for the exact model and do not use the output of the software....
Have you tried searching manually for a network? Which frequencies are used on the philipines 900, 1800 or 1900 MHz?
Maybe you inserted something wrong in the band selector, and your device is running in the wrong frequency. You can assign the correct frequency via band selector or in the bootloader.
If you haven't used the device for a while, is your sim card still active. Maybe it's out of order or anything else happened to it....
Stefan
LumpiStefan has right :
If your device is pw10A1 then you must use a radio stack 4.xx like 4.21 for example and select the good frequencies with band selector.
folks,
thank you sooo much for the reply.
as for the model, the sticker says it's PW10B1. i am using an active SIM. i posted the topic last night but when i got back in the office this morning, everything was back to normal. but again, i still dont get it...all of a sudden the signal came out of nowhere. hehehe! really, thank you for your posts and cheers!
God Bless!
maybe it's because your country use 900/1800 ?
in that case the phone would only work when it's getting a 900 signal ?
after i receive the xda, i automatically unlocked it using the software you guys unselfishly shared to me. and it worked! but after using it for like 4 months (not sure...probably this long), it just stopped getting a signal. i re-installed the same software but it did nothing. so, i decided to post this topic last night...and this morning, it went well again...for no reason at all. i am pretty sure i didnt change any settings. anyway, i am VERY GLAD you guys came to the rescue...even though my device just "cooperated" without being bugged(by me...hehehe!).
Hi!
Got a question regarding the Radio Stacks. I am using an XDAI from O2 Germany, which has the latest Radio Stack released by O2 themselves, which is 4.21. During more or less aimless surfing sessions in the undocumented backwaters of the Internet (dyndns sites :roll I found Radio Stack updates with non-linear version numbering which are not ActiveSync updates but install directly from the device.
- What is the difference (except the installation mechanism)? Are those safe to use or am I bound to screw up my phone using those?
- Why is the version numbering different? After my 4.21 the site lists A20.10, 6.24.20 and 6.25.24 as available. Which one is the most recent for my PW10A1? The 6.25.24? Or can/should I use the A20.10?
The reason I am considering the upgrade at all is that I get weird "clicks" and connections losses during conersation, especially after the first few minutes of conversation. To me and the other side it sounds as if I was temporarily driving through a tunnel or something, the connections keeps up but no speech is transmitted. And all that while the signal meter gives me 70-80%.
Or could it be a problem that I am using my O2 XDA with a T-Mobile prepaid card? I always considered GSM to be pretty generic. GPRS etc. is not in use on the device.
Any input? If this questions has been asked before, please be so kind and point me to the corresponding thread, I couldn't locate it with the search function.
The 6.xx Radio Versions are for PW10B models (900/1900 MHZ networks)
The 4.xx Radio Versions are for PW10A models (900/1800 MHZ networks)
The A.xx Radio Versions could be for for any of them.....
Flashing the wron version could end your device as a paperweight.....
Stefan
I did Flash with the 3.17.03eng the pw10a1 radio stack with 6.20.xx i don't know,
what i should do throwe the **** or what
fakbrenjeri said:
I did Flash with the 3.17.03eng the pw10a1 radio stack with 6.20.xx i don't know, what i should do throwe the **** or what
Click to expand...
Click to collapse
Are you sure you have a PW10A model? Check the rear sticker of this device. Normally ends flashing the wrong Radio stack in GSM Error.
In the wiki is a howto about this....
Stefan
hi, Stefan
Yes i am sure that the model name is PW10A1, and could you please help me about it
regards
Can someone advise me please I am new to XDA
when installing "XDA-developers Special Edition ROM" did you have to leave the sim card in the phone during installation?
Kind Regards
Moore, the rom doesnt affect the radio stack so it doesnt make a difference.
Cruisin-thru,
Thanks
much appreciated. NO SIGNAL what have I done wrong.
Regards
Enter bootloader, once bootloader shows press the button below antenna, choose your band from there, if the label on your phone says PW10a1 then choose 900/1800. If its PW10B1 then choose 900/1900. Hope that works for you.
Thanks,
I have PW10B1
The botton under the earial is the Calender bottom. should I choose the
900/1900 I thought is for America and North America.
I live here in England.
would it still work. do I need to change the GPRS as well?
Regards
If the label saya PW10B1 then your phone is capable only of 900/1900 which is for USA mainly, if your sim card is from Orange T-Mobile or Virgin then it will not work for that phone, all that will work will be Vodafone O2 or Tesco. It is no good choosing 900/1800 because the hardware will not allow this.
Thanks very much