I have the XDA developers ROM running on my T-Mobile XDA. I think I have the connection to GPRS working ok. Just that when it connects it asks for a Username, Password and Domain.
Does anyone know what these should be????
Any help greatly appreciated!!!
Miss Twinky
T-Mobile UK
T-Mobile UK settings are -:
general.t-mobile.uk
username, password and domain are blank.
Thanks But..
Thanks but I was looking for the US settings.
The APN I am connecting to is:
internet2.voicestream.com
with the dialstring:
+0 ~GPRS!internet2.voicestream.com
I have tried leaving the Username & Password blank to no avail
Thanks
Miss Twinky
I am t-mobile US PPCPE the string above is all i needed no username or password was required.. I just left blank and it seems to be working fine
I just set up my GPRS.
Leave both blank. Check Remember box.
Every step and detail is outlined here: http://www.mywirelessoffice.com/xda/romupdate.doc
Related
Hi,
I got this unit from ATT and now using with Cingular. I am trying to get to GPRS and internet settings for cingular. When I call them they say they don't know it since it is not their phone.
Is there anyone who managed to get the internet connection on another network? And how please?
Thanks,
Fatih
GPRS configuration
have the same problems. i got the MDA form T-mobile but need to use it with austrians mobilkom GPRS. I didnt manage to connect up to now!
I managed to get it working.
Here how it is:
Get the APN, user name and password info from your provider, and have your GPRS account activated.
For cingular users
APN: wap.cingular
USER: [email protected]
pWORD: CINGULAR1 (PAY ATTENTION TO LOWER/UPPER CASE)
Go to
>settings
>connections
>connections
>select "new"
>select "Cellular line GPRS"
>it will ask you APN
say connect.
Then it will ask user name and password. That's it.
Fatih
I'll try. thanx
Fatih,
I tried your settings and its ask for username, password, and domain. what should I put for domain?
No Domain Required
Just put in the info listed above. Then it will work great.
Good Luck!
fatih said:
I managed to get it working.
Here how it is:
Get the APN, user name and password info from your provider, and have your GPRS account activated.
For cingular users
APN: wap.cingular
USER: [email protected]
pWORD: CINGULAR1 (PAY ATTENTION TO LOWER/UPPER CASE)
Go to
>settings
>connections
>connections
>select "new"
>select "Cellular line GPRS"
>it will ask you APN
say connect.
Then it will ask user name and password. That's it.
Fatih
Click to expand...
Click to collapse
Sorry.....
that I didn't quite get it
after connected to the wap.cingular
what should I do next????
You mean add another new moden????????? :?:
Thanks for you help
SX 56
I use the settings for my sx56 and the internet only works when its connected to the cradle, I use comcast highspeed cable. any help in resolving this problem would be apreciated
Thanks for the info. Popped it in, everything's working great now.
Can someone point me in the right direction I've doen numerous searchs and talked to tech support (useless) . I have a 8125 that I picked up, although I am a AT&T sim card user (our company hasn't upgraded yet) so I unlocked the phone and it works great. although I can not access mmode or anything email or Internet related unless using wifi.
Can someone point me in the right direction for some instructions on how to get this thing set up to work with the legacy AT&T wireless system?
You need to manually enter the AT&T GPRS and MMS settings.
Call up AT&T and ask for the necessary information. They'll give it to you.
PM me you're email address I have the cab file that I can send to you.
gamescan said:
You need to manually enter the AT&T GPRS and MMS settings.
Call up AT&T and ask for the necessary information. They'll give it to you.
Click to expand...
Click to collapse
Well they don't exist anymore and the guys at Cingular could only get me so far. that's why I'm looking around for it.
Mark, you have a PM, thanks in advance
Cab file didnt work Mark. Only change it made was resetting my today backround to the default. all the settings are still the same.
is there a list of settings or a walk through for setting it up manually somewhere?
It should have worked.
Here is what I have:
MMS Configuration
Retrieve Messages Immediately
Save Sent Messages
Servers
AT-T MMSC
10.250.250.100
9201
http://mymsc.mymmode.com
My Work Network
100k
Wap 1.2
My ISP
AT-T Internet
Cellular Line (GPRS)
Proxy - Proxy Name
Work Network
AT-T WAP
Proxy - Proxy Name
Proxy
This network connects to the internet
This network uses a proxy server
WAP 10.250.250.250 9201
Secure WAP 10.250.250.250 9203
Hope this makes sense.
Another option is to go to the Cingular web page and choose Support, Phone/Device Support.
Select the following:
Network: former AT&T Wireless"
Manufacturer: Siemens
Model: SX66
Use the information in Device Setup to configure the browser/internet and MMS settings. It won't match exactly because the SX66 is a 2003 device, but you should be able to figure it out.
I've got O2 Exec, but i dont know information to setup for GPRS.
Can you help me, pls??? Thank you so much!
On the same note does anyone know the settings for simyo/ eplus in Germany?
thanks,
Mike
it's really easy, you only need a couple of details !! for O2 in the UK
Go to settings in the start menu
then connections TAB
Connections Icon
Add a new modem connection
Name it what ever you like (officially it is O2 Active)
Modem IS NOT default Cellular Line, change to Cellular GPRS/3G hit next
Access Point name = mobile.o2.co.uk all lower case, and that says letter 'o' not number '0' in o2 then hit next
username is o2web
password is password
no need for advanced tab just hit finished
Modem settings
I thought the username was mobileweb and the password as password. This works for me flawlessly.
You can also use a username and password of "faster" which sends images to you compressed - and then the full version when you refresh the page.
Hello all,
I've just managed to unlock (Thanks to buzz-lightyear!) my lovely uni from T-Mobile to be able to use my tesco simcard (until the vodaphone ones come through) I seem to be able to make/receive calls as I should be.
However, I got a message from tesco shortly after making my first call which said 'Your phone does not appear to be able to accept automatic settings, please call our care team on blah blah blah to resolve the problem'.
Did that and while the guy I spoke to had never heard of the handset, he provided me with a bunch of settings which I somehow need to stick into the system. They are as follows:
WAP
homepage = http://wap.tesco-mobile.com
apn address prepay.tesco-mobile.com
gateway 193.113.200.195
username tescowap
password password
port 9201
MMS
http://mmsc.mms.02.co.uk:8002
apn - prepay.tesco-mobile.com
ip = 193.113.200.195
username tescowap
password password
port 9201
Click to expand...
Click to collapse
My question is this: Where and how do I get these settings into this phone. Is the gateway similar to the WINS? I'm not sure what I need to do here, I would dearly appreciate anyones help on this.
Also, I want to donate a few quid to buzz and here, but when I try to do it on buzz's site, the paypal site comes up in German. Any ideas there please?
Thanks very much.
Alan
I have no interest in MMS so cannot advise but about the wap/internet ...
AFAIK tesco mobile runs on O2 network. My O2 PAYG setting are as follows; settings, connections, advanced, set to my work network. Add a new modem connection. Put a name and choose "cellular line (GPRS)" Next enter apn address. Next enter username and password. Finish. Under proxy, tick "this network uses a proxy.." Put 193.113.200.195. Tap advanced and put 193.113.200.195:8080 for the first 3 and 193.113.200.195:1080 for the last. Soft reset.
If this doesn't work I would try your same APN. username and password, but without proxy.
triplejay, thanks very much!
I haven't done it yet but I have a feeling those settings are going to work. The IP address you have supplied is the same one the tesco mobile 'care team' member gave me. I didn't end up online, but I think because we didn't put a proxy in, he wasn't sure we needed one.
I'll give it a go and see what happens there.
Thanks again!
Sorry to drag this up, but has anyone else got this phone using a Tesco Mobile sim? For all I try, I cannot get MMS to work. If you do, please let me know all of the settings and where I need to put them into.
Cheers
Thanks triplejay, I followed your instructions and they are spot on. Also thanks to inksmithy for the info. Im back on the mobile web - yeha!! Good stuff fellas
Those of you who are using 3G on your Uni, can you please check your settings and let me know what do I need to do in order to set up my 3G connectivity please!
I already have the following:
APN
IP Address
2 DSNs
however when I enter this information it doesn't seem to connect perhaps I'm doing something wrong.
I do have a data plan (3G) so that is not an issue which I am currently using with my iphone without any problems.
Thank you very much for your help!
Over 30 ppl read this post and none of you on 3G?
Please your help is greatly appreciated
Re 3G setting for a Uni,
Hi serjay,
Sorry for the wait I have only just come across your message. Here are the setting you need. I hope they work for you?
You can input all the settings, but I can't seem to be able to access the 3 portal.
In settings, connections tab, connections
advanced tab, select networks
new, and input the relevant info from here:
Data accounts: Create one called 3 GPRS.
APN: three.co.uk
Username:
Password:
Login request: Off
Allow calls: Automatic
IP address:
DNS address:
Authentication: Normal
Data compression: Off
Header compression: Off
MMS settings can be entered via outlook menu
gateway: http://mms.um.three.co.uk:10021/mmsc
proxy: 217.171.192.2
port: 8799
(account is the 3UK avvount above)
Not sure if u need to input the Video gateway.
If anyone know how to actually open the portal, plz help,
I think the problem is that the page detects what device you are using, and an exec is not on their list
secondly - use the http://mobile.three.co.uk/hb/7600/HutchKey as access to the portal - just make it your homepage. this one is for nokia, it works with me.
For those who won´t get the 3Zone to work, try the following:
Using a registry editor, find the following key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Internet Settings\5.0\User Agent
then edit the default value to "Nokia6680"
reset
and then surf to the 3Zone Homepage for a nokia 6680 (ask someone who has one to find the url out)
3 Reads the "User Agent" String of the browser yourphone uses to find out which phone you have.
With the trick above you configure the Pocket Internet Explorer of your universal to convince three it is indeed a nokia6680.
So normally you only get phones to work which three has in it´s program.
Regards
Michael.
m1dul said:
...In settings, connections tab, connections
advanced tab, select networks
new, and input the relevant info from here:
Data accounts: Create one called 3 GPRS.
APN: three.co.uk
Username:
Password:
Login request: Off
Allow calls: Automatic
IP address:
DNS address:
Authentication: Normal
Data compression: Off
Header compression: Off ...
Click to expand...
Click to collapse
Hi Michael, thank you for your help but I was unsuccessful; perhaps I’m doing something wrong.
This is what I’ve done:
Start
Settings
Connections Tab
Connections
Advanced Tab
Select Networks
New
Entered “3 GPRS” as my ISP name
Modem Tab
New
Renamed connections to “3G”
Selected a modem: Cellular line (GPRS, 3G)
Next
Entered Access point name:
Next
Entered User name, and password
Clicked Advanced
Selected “Use specific IP address” and entered the IP
Servers Tab
Selected “Use specific server address” and entered both the DSN and Alt DSN
Ok
Finish
Soft Reset
However I still can’t connect!!!
Please if you can provide further direction; hopefully I’ve done something wrong…
Hi serjay,
Sorry for the wait I have been on short break to Kent so I have not managed to come back to you.
All I can think of when I did it on mine was I left Username and Password blank and the IP adress as well.
I am sorry I can not help you any further because I use a Nokia N95 as my mane phone now and not the PDA.
thank you Michael for your help thus far, I guess I'll keep on trying.
Thank you..
m1dul said:
All I can think of when I did it on mine was I left Username and Password blank and the IP adress as well.
Click to expand...
Click to collapse
It worked! I left the username, pass and ip address blank and it worked!! thank you very much!
However 3G on Uni is 5 times slower than on the iphone... a shame!
serjay said:
It worked! I left the username, pass and ip address blank and it worked!! thank you very much!
However 3G on Uni is 5 times slower than on the iphone... a shame!
Click to expand...
Click to collapse
Glad it worked for you.
serjay said:
It worked! I left the username, pass and ip address blank and it worked!! thank you very much!
However 3G on Uni is 5 times slower than on the iphone... a shame!
Click to expand...
Click to collapse
Well, you have to notice the Uni is 4 years older than Iphone, so.... it´s no too bad. Remember when Uni came out no other device can do all that Uni!!
Uni it´s like the grandpa of all the new devices, so we have it some respect as even some of the today devices are not as good as UNI