Your guide to making serial cable is a bit iffy! You say we shall call this pin number 1 but we haven't got any confirmation about this... Is it pin 1 or not - doesn't fill me with confidence
Is it possible to make a USB to serial adaptor cable? I assume not as there arn't enough wires on the USB cable but I'm not familiar with this at all - yet!!
I've searched the web for a guide to serial cable pin layout but I can't find anything anymore.
Might just go and buy one and hope for the best.
Cheers
Fud
Also...
Can see anywhere if you can use a laptop to connect via IR com1 and unlock the xda with Manipulator.
IR port is not active.
So no this is not possible.
Can anybody help?
I still cannot get this to work. I have made my serial cable using a null modem cable and the board inside the O2 cradle. I have used a circuit tester to find the continuity between the actual XDA connector and the power connector for the cradle (con2 i think) - It has all the relevent pins for the serial connection.
Manipulator sits on the scanning ports screen and ActiveSync seems to be stuck in a loop but does not connect. I have obviously disabled ActiveSync b4 trying to connect with Manipulator and vice versa.
I have also attempted to rewire this as advised by one of you on another forum - using just the TX RX and GND pins as I am only trying to unlock the phone. This still does not work.
If somebody could send me a diagram of the serial connection it would help because the instructions here are a little vague. With just TX and RX connections I have wired up as so:
Com Port------------XDA----------------Con2
2-----------------------8-----------------5th connector from left
3----------------------10----------------7th from left
5-----------------------2-----------------1st from left
Also looking down on the circuit board with con1 away from you and con2 toward you. Con1 Pin 1 is on the right - right?!
I could go and buy the cable but to be honest I would probably just go and get a new phone on O2 to use that sim. I would really like to get somewhere on this coz it's now annoying!
Working
Sweet, Sweet, Sweet.
Didn't work with Manipulator but works with terminal prog??
I am now unlocked
Radio 4.06
Wallaby 5.15
Dunno if there is a prob with it - but just to let you know...
THX
Hi all First time poster,
I have been looking through your forums now for quite a while and havent found what i am looking for so this is the problem.
Does the mda compact have a serial port or not.
I am after making a serial lead for my gps and was wondering if this is possible.
I have emailed Pc-Mobile about a lead and they tell me this device doesnt have a serial port but in the specification in the book it says
Connection - Mini USB individual port for signals(for USB,Serial, and Power)
hope someone can help
thanks
shaun
USB = Universal Serial Bus
It is possible that it lacks a serial port, this is a similar situation to the ipaq 1910/1930, they have usb but no serial protocol so the only way to use gps is through the infrared port.
Thanks
Do you think this is worth trying and if so any ideas how
Anyone got a wm5/ce5 usb host driver for htc universal (pxa270 intel arm processor)? I'm trying to write one, but if someone could save me the effort, please do? I know it will work, as it does under linux.
USB Host on a universal will be great. Didn't know it works under Linux.
driver for view a universal as a sd writer and reader or a driver for the universal for attach a pendrive to a universal?
drivers for attaching a pendrive.
A USB host driver enables you to hook up USB devices like memory key, keyboard/mouse etc. to the universal. This feature is only available on a few pda models made by toshiba, fujitsu, asus, acer etc.
imesh said:
driver for view a universal as a sd writer and reader or a driver for the universal for attach a pendrive to a universal?
Click to expand...
Click to collapse
Correct me if I'm wrong but wouldn't it have to be supported by the hardware? As far as I know the Universal does not have USB host so getting a driver wouldn't be much help...
apparently it works under linux so the hardware must support it
Good question. I need the host driver and then a driver for mass storage (e.g. pen drive, hard driver, etc), HID (for keyboard mouse), etc. The htc universal has a usb host controller built into the arm processor (pxa270). The problem is that it also has a usb device controller build in which takes precedent for the mini usb out, so you can use activesyn. However, with the right bit of code you can reconfigure port 2 to act as a usb host. The other problem is that port 2 doesn't have any power (but that is easy to fix with an external power source from a usb hub or battery [I use a single AA battery, (giving 5 volts at 0.5-1 amp), that lasts for 2 hours]).
hi any success yet with the usb host function? is it possible or just a hoax?
nothing personal it just seems that some ppl like to make fun about this topic and spread hoax!
u have any evidences that it works under linux?
maybe this link is helping you in creating a driver!
http://www.deje.gmxhome.de/index.html
cheers
Mike
Suspect that you will also need the proper USB host cable that is used on the Sharp Zaurus under LINUX to let the Universal know that you want the USB port to work in host mode, they are about £10 & available from here http://www.figlabs.com/catalog/product_info.php/products_id/33
I have the Zaurus & Universal so I know the cable fits but I don't have a driver to test.
Mike
Mikew said:
I have the Zaurus & Universal so I know the cable fits but I don't have a driver to test.
Click to expand...
Click to collapse
The USB host is used by Linux on HTC phones, but not for the external USB connector
(BT on magician, and gsm_data on some others http://wiki.xda-developers.com/index.php?pagename=HTC_Serial)
Mikew said:
Suspect that you will also need the proper USB host cable that is used on the Sharp Zaurus under LINUX to let the Universal know that you want the USB port to work in host mode, they are about £10 & available from here http://www.figlabs.com/catalog/product_info.php/products_id/33
I have the Zaurus & Universal so I know the cable fits but I don't have a driver to test.
Mike
Click to expand...
Click to collapse
I have one for wm2003, I not if it worked in wm05.
Yuo can try it?
any success yet??
Dont think I would want to try a WM2003 driver on a WM5 device.
Mike
Mikew said:
Dont think I would want to try a WM2003 driver on a WM5 device.
Mike
Click to expand...
Click to collapse
You can do one backup before installing it.
I have installed it in my Universal and I have not had problems with wm5, but it has not worked with my standar cable
I've had no success with it either.. I have a cable that has the correct connectors.. originally used for connecting a usb pen drive to my lcd picture frame.. but like I said no luck with this RATOC driver.
Mikew said:
Suspect that you will also need the proper USB host cable that is used on the Sharp Zaurus under LINUX to let the Universal know that you want the USB port to work in host mode, they are about £10 & available from here http://www.figlabs.com/catalog/product_info.php/products_id/33
I have the Zaurus & Universal so I know the cable fits but I don't have a driver to test.
Mike
Click to expand...
Click to collapse
i think that this cable is not enough, what about a 5v power source for the usb pen drive you'd connect?
your universal couldn't supply that, then you need a usb cable that can connect to a power source aswell.
You need to use a powered USB hub if the slave device requires power, there are one or two hubs that run on batteries so you can still be mobile.
You will need a hub if you plan to use more than 1 USB device at the same time.
Mike
allmycrud said:
Anyone got a wm5/ce5 usb host driver for htc universal (pxa270 intel arm processor)? I'm trying to write one, but if someone could save me the effort, please do? I know it will work, as it does under linux.
Click to expand...
Click to collapse
I didn't know we had it in Linux yet??
In any case, while many devices do use a USB Host or USB Slave chip from a higher level, I believe the Universal talks to its USB as a raw stream device, and therefore can (and does, on occasion) act as a pure Serial communication channel (no discernable protocol beyond 8,n,1) or, therefore, any other type of serial-based channel. Yes, what I am saying is that you could, in fact, hook up a Serial ATA hard disk to an RS232 or USB port directly, so long as the device with the port has low enough level access to the port to absolutely control the data I/O.
The problem you face, however, is that to use the USB port as if the device were the host, you would first need to remove or disable whatever makes it work as the slave. In Windows Mobile that's really not an easy job given the number of different devices and different drivers, some with USB chips, some without... On many devices I can imagine that doing that alone would really bugger up general operation. What happens, for example, to ActiveSync when you suddenly get rid of the port it usually talks to for sync?
Mikew said:
You need to use a powered USB hub if the slave device requires power, there are one or two hubs that run on batteries so you can still be mobile.
You will need a hub if you plan to use more than 1 USB device at the same time.
Mike
Click to expand...
Click to collapse
Some USB devices have batteries, or have their own power supply You can also get USB cables with an extra (mains or battery) feed wired to the USB's power lines in parallel.
whatever happened to this thread?
allmycrud have you seen the thread from Zeno with USB host drivers?
there is at least one report of it working on a Universal, but I can't get it working on wm6.1... still have hopes though, as all reports suggest that USB host is possible on a uni... can never get verification from anyone though...
Hey guys!
I've searched and searched for something to allow me to transfer data via a serial cable from my phone to device.
Let me try to explain this.
HTC Wizard
Windows Mobile 6 (Explore 1.1)
I have style tap (palm os emulator)
Software for palm os for a stand alone fuel managment system (msefi.com)
So on my car, I use a serial cable to program and get realtime data.
Now I know they make bluetooth to serial adapters for around 70, but I was wondering if they make a mini usb to serial cable for the Mobile OS.
Anyone have any ideas?
Thanks
Chris
Well, you could theoretically get a USB to serial adapter that has a cable. Then cut the USB connector that goes to the PC off the cable and just splice the miniusb plug onto the end. I don't know about device support though I'm going to guess you would have to at least come up with a driver and the device might not support that type of functionality at all anyways.
Since the Wizard doesn't have a USB Host (aka USB OTG) the short answer is no. Even more importantly, the wizard won't power the serial adapter so the device is a dud to begin with.
The odds that the BT to RS232 connector method will work are far greater than the USB method.
wondering if there is an adapter somewhere to allow me to plug in my Evo4g(or any mini USB phone) to an RJ45 connector...for example a console port on a switch/router and use a terminal app to configure it.
is this even possible?
thanks for any info
Wow...
Wow lol, while that's a pretty cool idea I doubt it could work... I use a USB to Serial adapter on my laptop to connect to switch gear with a Cisco cable, this one specifically,
http://www.amazon.com/Keyspan-USA-1...1?s=electronics&ie=UTF8&qid=1318030317&sr=1-1
but the phone itself would have to have a driver for it, or you'd have to custom code one yourself... Either way I'm not sure a phone would even support serial emulation over its USB connection. Cool thought though!