Junsun v1 pro 2GB and 32GB Video AUX issue - Android Head-Units

Hello folks. I have a very big problem and I am infinitely sad about my new radio.
The following problem, I installed the junsun v1 pro in my BMW E91 and installed a reversing camera which is located in the recessed grip.
But the pin on the radio itself with the 10-pin pin from the video chinch with the black cable (red and black on the video chinch) broke off because there was too much voltage on it. was my fault
How can I fix this pin in the radio or is there an alternative to connecting the camera via chinch without having to use the pin or another slot on the radio so that it still works? An adapter maybe?
It would be so nice if maybe someone could help me or has a tip? I'm really desperate.

Hello. Please. Help me!!!

Get a new pin and crimp it on the wire, put it back in.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Thanks for the answer.
Aja and then insert this pin from the outside through the plug, you mean? It works like this?
There is no other slot on this radio?
There are two more slots above this slot with the camera.
What are these for?
My picture is there at the beginning but it flickers or disappears shortly thereafter when I drive. I soldered a pin but I'm not sure if it's okay or if the wiring is causing me a problem.

Related

USB damaged - need diagram!

Hi All,
I put this question on MODACO (the place of how to take the JamIn apart!) for a week but got no reply - so I hope someone here can help me!
http://www.modaco.com/USB-damaged-t255421.html
I had the famous earphone-spring switch stuck & my phone always tried to use the earphone.
Thanks to the wonderful tutorial from Iain, I managed to open the case & fix problem.
Unfortunatly, something went wrong while using the hot air iron - Now I've no USB connectivity!! - It's charging but no AS connectivity!
I want to check a component placement.
there is a place for a diode near the USB socket on the PCB - there's no diode on my phone only a silk screen label indicating that a diode should be there - and I think that the hot air iron blow the diode away.
Would anyone please check his phone - post a photo of the PCB on both sides of the USB connection or send a schematic or a circuit diagram for the prophet.
Unfortunatly I don't have a digital camera other than the one on the phone
Thanks for yor help
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hi all,
Any help?!?!?!?!?!?!?

[Q] Screen permanently turned off while performing service for my G2.

Hello Guys.
I got some problem with my 3.5mm jack, so I decided to order a whole new tape with USB connector and 3.5mm jack port.
http://thumbs2.ebaystatic.com/d/l225/m/mRfGTPTIX7tNp0yCo0_JEmQ.jpg
Got the package with small toolkit to open phone and change this thing by myself.
I've followed instructions from one of many youtube DIY movies.
New parts got installed, everything went pretty well... then closed phone. Turned On... and here I em...
Power button doesnt work, I see no light around the power button, no screen reaction... But I hear that phone turned on because of LG logon sound. Phone reacts while pluged in to charger, USB->PC too.
Attached picture with exact conectors I plugged off while changing parts inside.
Why power button doesnt light up? Why doesnt work? Is there some small connector between power button and the board, because I dont see any, there is a Toshiba Chip just beneath the power button/volume part.
Please help me, give me some advices what exactly could get wrong.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thank You for any help.
Sorry in forward for my English...

Junsun - improving WIFI reception with external antenna

I own Junsun Android radio with standard I would say pinout on the back. Noticed that there is a pin for external WIFI antenna.
Has anyone tried this pin and installed external WIFI antenna?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hi,
you shold receive a small plug with your head unit. Its video RCA cinch and there are also two blue wires circa 3cm long. One is wifi antenna, the second is forBT.
wotii098 said:
Hi,
you shold receive a small plug with your head unit. Its video RCA cinch and there are also two blue wires circa 3cm long. One is wifi antenna, the second is forBT.
Click to expand...
Click to collapse
that is great, I was just going to post it, realized this last night.
The question I have: how do you connect commercial antenna with two part ( main conductor and shielding ) to this one wire?
@wotii098
should I solder the blue cable to the center pin of the WIFI antenna?.
should the shielding be connected to the pin 9 ( GND ) ?
I didnt connect(or solder) antything to these wires. I just use them as they are and I can't complain about wifi/BT range.

Help for possible installation!

How can I connect the connector in blue photos with the certhiato photo 2 connectors? This is to use the original MIC Tiguan Many thanks !!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
You should have the right connector to your head unit, mostly provided with ISO connectors for Power and speaker.
There you need an adapter from ISO to Quadlock. Search for your car... BTW: for VW you also need a CAN adapter to get clamp 15 and SWC working.
If you don´t have anything... Get in contact with the seller, ask for the right adapter cable or send this thing back.
rigattoni said:
You should have the right connector to your head unit, mostly provided with ISO connectors for Power and speaker.
There you need an adapter from ISO to Quadlock. Search for your car... BTW: for VW you also need a CAN adapter to get clamp 15 and SWC working.
If you don´t have anything... Get in contact with the seller, ask for the right adapter cable or send this thing back.
Click to expand...
Click to collapse
Very Thankss! now search...

Jonsun 1G Can Bus connections

Hi,
I just unboxed the Head Unit for my Ford Focus MK2 and found that the wiring does not look like the very simple diagram on the sellers page.
Going from the can bus connector there are 2 wires to a white plug. One wire is green/white and one wire is white/green. I am in doubt where to connect this plug.
Further, from the can bus there are two wires going to the head unit. Its a red wire and an orange wire. The wires are split and connects to a plug. From the plug that is supposed to connecting to the car there is a socket with a red and orange wire. I am in doubt what happens wether connecting or not.
There is also an orange/brown wire marked Key2
Maybe photo explains better:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I would appreciate if someone could clarify for me.
Christian
Solved it myself
cl3884 said:
Solved it myself
Click to expand...
Click to collapse
They you may answer your questions here, to help other users.
Thank you.
It need to go in the free slot in the Head Unit but it is not shown on sellers page. There is only one slot that fits so its quite simple when you know.

Categories

Resources