Hi,
I am trying to Flash stock firmware to my X96Q.
I have installed the driver coming with phoenix suit (via Windows device Manager). After opening phoenix suit and choosing the img- file I connected the tvbox via USB while pressing the hidden Button in av-Port.
Phoenix suit is detecting my device and seems to start flashing but nothing happens (showing " elapsed time: 0s" ).
Also tried with phoenix usbpro. Same Story. The Green Button turns Red after connecting but nothing happens.
With the phoenix sd card burn tool I burned the Firmware to micosd and inserted into the tvbox. After power-on nothing happens (with and withlut Holding the button pressed while poweron) . Tutorials said there should be an installing progressbar beeing visible but the box only showing the red LED.
Some ideas?
Thanks
Some ideas?
Related
i bought my DEFY XT from a guy last week.it has a strange IMEI 004400152020000.Since all functions acted normally then so i considered it dosen't matter to me much.
I rooted the phone and replaced some system embeded applications to release disk space for apps that i used frequently.Then one day my customized desktop launcher didn't work.It stuck at moto logo with the four bottom button LED lighten.
I tried to transmit desktop launcher app via a download url contained in sms or bluetooth but my phone had no signal from network it showed that no service so the sms couldn't be received.
The bluetooth and usb debug option was checked off before the phone stuck.So there was no other choice than flash signed SBF back.
But after i powered off the phone,held the vol up then press down the power button,with my finger remain holding down the two button,the phone boot into moto logo normally and stuck as usual.
I tried many times but couldn't succeed in geting into bootloader even once.
I tried to flash zip package in recovery mode but after i confirmed update zip file from sdcard the screen was black and nothing happened.
I tried to hold vol up+vol down+power for about 20secs then finally the phone enter an interface as below in which the rsd lite strangely recognized my phone as X615.After i selected the SBF and press
"START", rsd lite showed that it was switching the device into flash mode,after a while it gave me an error message as"failed flashing process.Unable to retrieve interface handle（0x7027）“
Below is the message that interface showed and error message rsd lite gave.
interface message :
HW Model = TBP
HW Version=PR1
SW Version=IRM-1301
RF band id=GSM_BAND_1234,WCDMA_BAND_15
ProductID=TBPL2133100340
IMEI num=004400152020000
BT Addr=000000000000
WiFi Mac=0090C0F8F6AA
Battery ADC=4211
rsd lite error:
Maybe that strange IMEI was a result of that my phone had been bricked and resurrected before my purchasing?
nobody have encountered such situation?
it seems that my phone has no remedy
so sad
So this was I have done to create and to try and solve this issue.
I was running stock CM12 and wanted to flash a different ROMs, so I tried to unlock the bootloader and using "fastboot -i 0x1ebf oem unlock" and without restarting the phone, tried to flash 64bit TWRP recovery, after this the phone no longer booted, but TWRP was booting, with a lot of errors of not being able to mount "/data" and other partitions. So I downloaded the CM12 offical ZIP file to try and do a factory reset, flashed using "fastboot" with the file "flash-all.bat" and here is where the problem started, this process failed, I think because there is a "flash-radio.sh" file where the "fastboot" lines do no have the "-i 0x1ebf" and because of this (I assume it's this lol), this process failed and the phone no longer starts, nothing works, tried in windows, ubuntu and a MAC at work, nothing is able to see the phone any more, the only sign of life I get, is when I remove the battery and connect the usb cable, the red LED from the phone turns on, but the PC still does not detect the phone, followed a recommendation I found, to remove the battery, pressing and holding the volume UP button + connecting the USB cable + connecting the battery, all this whilst the volume UP button is still being pressed and also did not work, no signs at all of life =(
Not sure what to do more, any idea guys?
Can't return because I bought on eBay UK =(
Guys! Here's a problem. Yesterday has set itself a new stable firmware - 5.1.4.0A after the phone rebooted and hung on the OS boots. I decided to reinstall other version - now the phone is turned on, 20 minutes running and goes into an endless reboot (the logo MEIZU).
How can I escape from it? Flashing through recovery does nothing, it is possible as that through fastboot?
The only solution to boot up pressing th power button and "+" button. If it is power up the connect it to your pc. You must see a recovery drive. if not you need to install windows drivers for your phone. Then copy inside this drive THE VERY FIRST FIRMWARE that you phone was running before any upgrade. This was the only solution that worked for me and i try everythink else. Hope best luck.
Device- Galaxy Note 4 International (SM-N910C)
The case here is:
- The Phone doesn't boot, or show anything as the splash screen
- when you try to charge the phone (while powered off) the device doesnt show anything at all, but the phone charges as the
battery heats up a bit
- when you press the power button (and nothing else ) and leave the phone alone for about 8-10 mins, it shows the download
mode screen WITHOUT the details on the top left corner.
- removing the battery and putting it back didn't work, and when you press the download mode button combination (volume
down+power+ home), it directly starts download mode but this time WITH the details on the top left corner, the warning doesnt come.....
- When in download mode, the device IS detected by odin
- but then when i try to flash the rom thorugh odin, again the same
problem (no boot)
So far, Download mode is the only thing i've seen on the phone, and nothing else
my Guesses: the files which store the splash screens, etc are corrupted,and are not even touched during rom flashing, because when i flashed a rom through odin, the process DID finish but the problem persisted.
Suspects: param.bin file
even though these can be the root of the problem, there is no way i can actually restore the original file because adb doesnt detect the device in the pc, only odin does. Yes, i've perfectly installed all the adb/fastboot drivers.
Thanks in advance to anyone that helps fix the problem......:crying:
One more guess
MrXDA72 said:
Device- Galaxy Note 4 International (SM-N910C)
The case here is:
- The Phone doesn't boot, or show anything as the splash screen
- when you try to charge the phone (while powered off) the device doesnt show anything at all, but the phone charges as the
battery heats up a bit
- when you press the power button (and nothing else ) and leave the phone alone for about 8-10 mins, it shows the download
mode screen WITHOUT the details on the top left corner.
- removing the battery and putting it back didn't work, and when you press the download mode button combination (volume
down+power+ home), it directly starts download mode but this time WITH the details on the top left corner, the warning doesnt come.....
- When in download mode, the device IS detected by odin
- but then when i try to flash the rom thorugh odin, again the same
problem (no boot)
So far, Download mode is the only thing i've seen on the phone, and nothing else
my Guesses: the files which store the splash screens, etc are corrupted,and are not even touched during rom flashing, because when i flashed a rom through odin, the process DID finish but the problem persisted.
Suspects: param.bin file
even though these can be the root of the problem, there is no way i can actually restore the original file because adb doesnt detect the device in the pc, only odin does. Yes, i've perfectly installed all the adb/fastboot drivers.
Thanks in advance to anyone that helps fix the problem......:crying:
Click to expand...
Click to collapse
Can anyone try and give me a ODIN flashable file that replaces the param file in the phone???
I have a LG G2 D802 32GB phone. I have been on Lineage 15 for more than 2 years without any security updates. Foolishly, I downloaded and flashed the latest copy of the same operating system. Seemed to go OK but TWRP always booted into recovery, even when 'system' was selected. I flashed the original copy of the operating system and GAPPS back which again went without error messages. This time it booted up with the LG Splash screen followed by the curved line and circles followed by a blank screen then the line and circles/blank screen again repeatedly.
Switching the phone on whilst holding down 'volume up' and plugging the PC USB cable in, gets into download mode followed by the Firmware update screen which sticks at 0%. In the top of the box below are the words 'USER B49' and on the bottom of the box, in red, 'ROOTED' even though I had never succeeded in getting Magisk to root this phone.
The PC has the correct driver and pings but there is no visible entry in File Explorer or the bottom of the screen for safely unplugging it again. This is probably because USB is in Developer Mode but not set for file transfer or PTP etc. with no obvious way of changing this.
Sorry for being so verbose but can anyone suggest how to get the phone working again please?