Dead, Unbrick, Debrick F460. Dead/boot security error/boot loop kitkat,lollipop version bootloaders, 9006, 9008 modes
FIRST install lg united mobile drivers, connect mobile with battery to pc, check in device manager com ports if 9006 or 9008 mode.
if you can go into custom recovery mode twrp/cwm, then it easy to fix... u need to flash zip.but your self have to make it right now of same version. here the link tutorial.. http://forum.xda-developers.com/showthread.php?t=2451696 OR try adb or terminal command or u need to make zip file. i lost that link. better try ubuntu method also.
CASE1:
if 9006 or 9008 mode, ROOTED,on lollipop/kitkat/marshmallow before phone dead but rooted, first try debrick sdcard which is simpler, then use ubuntu method. this works only if rooted before phone dead. only root access allows to rewrite files on partition here is the link http://forum.xda-developers.com/showthread.php?t=2582142
CASE2:
only 9008 mode, phone dead on lollipop/kitkat/marshmallow, not rooted, then try debrick image and Ubuntu methods. sucess rate is very low.
Guys!
the sdcard debrick may success. then these files can debrick it.
OUr devices can be fixed. After lot of research i found it. kindly go through the link given below for tutorial and do debrick. You need to try from 140 to 220. hope YOU THANK ME HERE is the Link http://m.blog.naver.com/kangmincraft/220675995736
http://m.blog.naver.com/kangmincraft/220626785379
debrick 140 https://drive.google.com/file/d/0BwKzoXanfz0jMFh1OXJ2QnROUWM/view
debrick 160 https://drive.google.com/file/d/0BwKzoXanfz0jemxYR0VNcnZULXc/view
debrick 180 https://drive.google.com/file/d/0BwKzoXanfz0jb2R4eGIzV1BHeGM/view
debrick 200 https://drive.google.com/file/d/0BwKzoXanfz0jUHBTelc4VzlQT2M/view
debrick 220 https://drive.google.com/file/d/0BwKzoXanfz0jZFBXaFRLMFJVWGc/view
try this, this is my own debrick lollipop: https://drive.google.com/file/d/0B09V79Pt4dCUSjF0ZUhNRWxiQ0k/view?usp=drive_web
Read this post who unbricked his dead mobile http://forum.xda-developers.com/showpost.php?p=66264994&postcount=14
just poweron the device after inserting the sdcard. check few times. try to go download mode.
use google translator if needed.
TIPS
sdcard miniumum 4GB, use old sdcards first. then latest memory cards, try sdcard memory higher than phone memory is advantage. try these 3 types.
debrick140 worked for most of them. try this first if you are on lollipop.
Lollipop bricked roms have higher luck.
after successful unbrick, use poweriso/ultraiso to format sdcard. i used poweriso>tools>cleanusb. then format in your pc.
ATTENTION MARSHMALLOW: IF YOU NO ROOT, NO CUSTOM TWRP, NO DOWNLOAD MODE. THEN THERE IS NO DEBRICK IMAGE YET. NOTHING WORKS. GIVE TO REPAIR RIFF,OCTOPUS BOX. THIS GUY SELLING SOUTION https: //www. facebook.com/ giaiphapandroid/. (remove spaces)IF BOUGHT, SHARE THE LINK HERE . i am not seller,i don't vouch anyone here. just helping so that you help others.
if you have friends in vietnam/korea ask them to search MM debrick and share here. if anyone have solution for MM. kindly share here.
SENIOR XDA: I REQUEST YOU TO CREATE DEBRICK FOR MARSHMALLOW.
THANK ME IF USEFUL....
Credits to Vega_Kangmin.
all copyrights to respective owners. i made simpler type. so if read all and google search, everything you can get in detail.
Reply
Hi. My name is kangmin
And you can call me 'Vega'
At first.
That debrick.img is for G3 Cat.6 (F460 S/K/L.) In korea.
So, it didn't work for international phone
(Like G3 Prime.. Maybe.. Not sure.)
And second. This debrick.img file is for kitcat,lollipop.
It didn't work for mashmellow.
Vega_Kangmin said:
Hi. My name is kangmin
And you can call me 'Vega'
At first.
That debrick.img is for G3 Cat.6 (F460 S/K/L.) In korea.
So, it didn't work for international phone
(Like G3 Prime.. Maybe.. Not sure.)
And second. This debrick.img file is for kitcat,lollipop.
It didn't work for mashmellow.
Click to expand...
Click to collapse
Hello Vega,
yes, we need this for G3 Cat.6 (F460 S/K/L.).
Thank you for your hardwork.
how are you? i have been researched all your blog today and tired translating it to english, but still i cannot understand few words. KINDLY MAKE HERE ENGLISH TUTORIAL PLEASE.
my mobile is boot security error when downgrade from marshmallow to lollipop, 5%, laf error. so i need debrick image for F460S30c_00_1223 marshmallow version. could you please make a debrick image for it?
waiting for your private message reply
Okay. I'll going to write for english
But, i don't have much times because, i have an exam
So, i'll write it as soon as possible..!
Help me Vega
Hi Kathik, I have got a problem with my LG G3 Cat.6 F460k, no download mode, no recovery, no power on, no fastboot , only qualcomm hs-usb qdloader 9008 in windows device manager, tell me, You could please tell me what program I can use to fix this problem, I don’t have the files to use in the boarddiag application, because my g3 uses the APQ8084 chipset for the 805 snapdragon processor. Please brother, help me.
Vega_Kangmin said:
Okay. I'll going to write for english
But, i don't have much times because, i have an exam
So, i'll write it as soon as possible..!
Click to expand...
Click to collapse
Thank you brother!!
Thank you Kathik, I will try this method tomorrow in my Lg G3 F460K, then I will write the results, I have many faith in this!! By the way, thank you too for guide me via whatsapp Kathik, you are a truly hero bro!!!!
:good:
manowar24 said:
Hi Vega, I have got a problem with my LG G3 Cat.6 F460k, no download mode, no recovery, no power on, no fastboot , only qualcomm hs-usb qdloader 9008 in windows device manager, tell me, You could please tell me what program I can use to fix this problem, I don’t have the files to use in the boarddiag application, because my g3 uses the APQ8084 chipset for the 805 snapdragon processor. Please brother, help me.
Click to expand...
Click to collapse
manowar24 said:
Thank you brother, I will try this method tomorrow in my Lg G3 F460K, then I will write the results, I have many faith in this!! By the way, thank you too for guide me via whatsapp, you are a truly hero bro!!!!
:good:
Click to expand...
Click to collapse
Welcome bro. hope you fix and share it here
Vega_Kangmin said:
Okay. I'll going to write for english
But, i don't have much times because, i have an exam
So, i'll write it as soon as possible..!
Click to expand...
Click to collapse
Vega. do we need to press any buttons to go into fast boot mode after mounting sdcard? kindly search Marshmallow debrick and share the link please.
manowar
manowar24 said:
Hi Kathik, I have got a problem with my LG G3 Cat.6 F460k, no download mode, no recovery, no power on, no fastboot , only qualcomm hs-usb qdloader 9008 in windows device manager, tell me, You could please tell me what program I can use to fix this problem, I don’t have the files to use in the boarddiag application, because my g3 uses the APQ8084 chipset for the 805 snapdragon processor. Please brother, help me.
Click to expand...
Click to collapse
hi manowar.
you can solve the problem with using debrick.img files.
go to the link and solve the problem!
Hello Vega and Kathik, I have not done the process yet, I will do it tonight, and then I will inform the results.
I also wanted to thank you for the hard work you are doing in publishing this tutorial and translate it into English, I know you're still working on it, but so far it is understandable and looks promising.
I have some questions to you, to clarify the process that will perform tonight, please, answer me this:
I just have a 32 GB microSD Class 10, does this serve? Or it is too large in capacity? (By the way, my Lg G3 F460K is 32GB of storage and 3GB of RAM, it has Android Lollipop 5.0.1 with HOANG LAM CAT6 1.6 ROM and it was rooted)
When I will do the format to the microSD card, before passing by the win32Disk, what format I give it? ¿FAT32 or NTFS? Or the Win32 software do it for me when it will formated the microSD?
After inserting the microSD prepared, simply press the button on/off on the phone? Or I must do any combination of on/off + vol + or any other?
It is rare to found any solution for this korean model, there are only solutions for the international models, but it seems there is nothing for the Korean model (F460L,S,K). I hope that this work will help many people in this situation and prevent all those who are paying for solving this problem.
Please brothers, answer my questions and I will do the rest. Many thanks!!!
Vega_Kangmin said:
hi manowar.
you can solve the problem with using debrick.img files.
go to the link and solve the problem!
Click to expand...
Click to collapse
I´m in the process but....
Hello brothers, good news, my phone is now in Fastboot mode, I´m working with the ADB and CMD commads, but I have several troubles, please help me in this:
I dont have de file "misc.bin", when I disarmed the original KDZ file (kitkat or lollipop) doesnt appear this file. Do you have it? Please send me or letme download it
I cant erase o create the nexts files with the commads: BackupGPT.bin neither PrimaryGPT.bin, I recibe this message when I tried: "Failed: partition table doesn´t exits"
Brothers please help me on this!! I´m very close to fix my f460 all thanks to you!!
Hello brothers Vega and Kathik, good news, thanks to you I could get my phone back, it is now 100% operational, I would not have been achieved this without your support. However, some things did not go as shown in the tutorial, so I'll detail everything I did with my F460K to help everyone with this problem. Thanks to Kathik an d Vega for the debrick files, they are the key to solve this problem.
I am very happy, now I'll help whoever needs it , as Vega and Kathik helped me!!
THANK YOU TOO TO ALL MEMBERS OF XDA, WHO HELP ME IN SOMEWAY.
:good::good::good::good:
manowar24 said:
Hello brothers Vega and Kathik, good news, thanks to you I could get my phone back, it is now 100% operational, I would not have been achieved this without your support. However, some things did not go as shown in the tutorial, so I'll detail everything I did with my F460K to help everyone with this problem. Thanks to Kathik an d Vega for the debrick files, they are the key to solve this problem.
I am very happy, now I'll help whoever needs it , as Vega and Kathik helped me!!
THANK YOU TOO TO ALL MEMBERS OF XDA, WHO HELP ME IN SOMEWAY.
:good::good::good::good:
Click to expand...
Click to collapse
Welcome! happy to hear from you. share your experience here to help others.
do you wanna upgrade to MM? just follow this link http://forum.xda-developers.com/lg-g3/general/update-downgrade-root-lg-g3-f460-s-k-l-t3353542
How I bring back my G3 F460 from Death
Hello, I'll explain you all how I recovered my LG G3 F460K from death, I must first thank @Kathik and @Vega_Kangmin for their guidance, tutorials and files, without them I would not have been able to recover my phone, the steps are basically as they are explained in Vega_Kangmin´s tutorial:
http://m.blog.naver.com/kangmincraft/220675995736
However, I found some differences that stopped me so I had to read and research in Google to make decisions and to continue with the process.
These are the steps that I follow:
1. Download all programs and files suggested in Vega_Kangmin´s tutorial.
2. I extracted the files from the original KDZ Lollipop (F460K20C_00.kdz) and put it in the folder that I call “ADB”. (My G3 had the Lam Hoang 1.6 Android 5.0.1 Rom and was rooted with debugging enabled).
3. With the Win32Disk Imager I make the first boot image to use in the phone with a microSD card, first I try with the debrick image called “debrick140.img” and the screen did nothing, unanswered. Then with the win32Disk Imager I created the image boot with 160MB and bingo!! It works!!, the screen showed the LG logo and immediately fell in Fastboot mode. Here I tell you my first warning: the only microSD card that I have was a 32GB Class 10, so I used it, then the win32Disk Imager program created in it a new partition table and reduced the 32Gb capacity only to 85MB, so after I had saved my phone, I have to save my microSD card, for that, I used Ubuntu, and one program called “Gparted” I uses it to redefine the partition table. So, beware!!!
4. I opened a CMD´s window in the folder "ADB" (shift + right click, click on "open a command window here"), plugged my phone in the PC (Windows installed the drivers of ADB interface and immediately it recognized) and I wrote my first command to verify that everything was in order:
fastboot devices
If all goes well it should show up this:
List of Devices attached
LGF460XXXXXXX device
Then I proceeded with the ADB commands, but in the tutorial I found some errors in the syntax of the commands and the order they should be done, the correct syntax is:
To remove files the syntax is ok, example: fastboot erase aboot
This is the syntax to flash new files is: fastboot flash aboot aboot.bin
(Don´t forget to change names of the extracted kdz files)
And the order for all the process in the ADB pront is this:
fastboot erase aboot
fastboot flash aboot aboot.bin
fastboot erase boot
fastboot flash boot boot.bin
fastboot erase laf
fastboot flash laf laf.bin
fastboot erase rpm
fastboot flash rpm rpm.bin
fastboot erase recovery
fastboot flash recovery recovery.bin
fastboot erase modem
fastboot flash modem modem.bin
fastboot erase SBL1
fastboot flash SBL1 sbl1.bin
fastboot erase tz
fastboot flash tz tz.bin
fastboot erase sbi
fastboot flash sbi sbi.bin
fastboot reboot
exit
Note: none of these files should be used BackupGPT.bin, PrimaryGPT.bin (if you use it the ADB will return an error saying that these tables do not exist, the file misc.bin neither will use because we do not have it and it isn´t important to revive the G3, this information I got it from here:
"YOU NEED TO EXTRACT 10 FILES FROM TOT (if you use a tot file) (aboot, boot, SBL1, dbi, laf, recovery, modem, misc, rpm, tz) and 9 FILES FROM KDZ (this is our case for the Lg G3) (misc file is not present in KDZ so dont worry it is not important) "
That out of here, please read it:
http://forum.xda-developers.com/android/general/unbrick-lg-model-download-recovery-t3060184 -----> Thanks to @hacklockx
5. After restarting the phone it show up the LG logo (this is a good news), so flash an official ROM with the LG Flash Tool as you already know and enjoy our super phone again.
By the way, in my case, after the process restart with the ADB commands, my phone start normally with all my stuff installed, I lost nothing, as if nothing had ever happened, however, I noticed slow and the camera didn´t work so I flash it with the official rom F460K20C_00.kdz and it was like new. Then I rooted it, installed the TPWR and flash again the Lam Hoang 1.6 ROM with Android 5.0.1, then installed the Xposed and that´s all!!
I hope you serve!!
Greetings from Venezuela :good::good::good:
Guys, I need help. My F460L is bootlooping but I can still access download mode. I tried flashing stock MM with LG Flash Tool but it is still bootlooping, what do I need to do?
Jinyung411 said:
Guys, I need help. My F460L is bootlooping but I can still access download mode. I tried flashing stock MM with LG Flash Tool but it is still bootlooping, what do I need to do?
Click to expand...
Click to collapse
Try these options:
1. Change your battery, try another one, in my case I have two battery, one cause endless bootloop on my G3.
2. Use the "LG Mobile Support Tool", install the program, open it, connect your G3 and see the magic happens :good:
Good luck bro
manowar24 said:
Try these options:
1. Change your battery, try another one, in my case I have two battery, one cause endless bootloop on my G3.
2. Use the "LG Mobile Support Tool", install the program, open it, connect your G3 and see the magic happens :good:
Good luck bro
Click to expand...
Click to collapse
I tried using LG Mobile Support Tool but it does not work either. I'll try the battery, thanks. Will report back.
Jinyung411 said:
I tried using LG Mobile Support Tool but it does not work either. I'll try the battery, thanks. Will report back.
Click to expand...
Click to collapse
check this link. downgrade to Lollipop. follow this link http://forum.xda-developers.com/lg-g3/general/update-downgrade-root-lg-g3-f460-s-k-l-t3353542
THANK ME IF I HELPED YOU. also MUST write feedback
Kathik said:
Dead, Unbrick, Debrick F460. Dead/boot security error/boot loop kitkat,lollipop version bootloaders, 9006, 9008 modes
FIRST install lg united mobile drivers, connect mobile with battery to pc, check in device manager com ports if 9006 or 9008 mode.
if you can go into custom recovery mode twrp/cwm, then it easy to fix... u need to flash zip.but your self have to make it right now of same version. here the link tutorial.. http://forum.xda-developers.com/showthread.php?t=2451696 OR try adb or terminal command or u need to make zip file. i lost that link. better try ubuntu method also.
CASE1:
if 9006 or 9008 mode, ROOTED,on lollipop/kitkat/marshmallow before phone dead but rooted, first try debrick sdcard which is simpler, then use ubuntu method. this works only if rooted before phone dead. only root access allows to rewrite files on partition here is the link http://forum.xda-developers.com/showthread.php?t=2582142
CASE2:
only 9008 mode, phone dead on lollipop/kitkat/marshmallow, not rooted, then try debrick image and Ubuntu methods. sucess rate is very low.
Guys!
the sdcard debrick may success. then these files can debrick it.
OUr devices can be fixed. After lot of research i found it. kindly go through the link given below for tutorial and do debrick. You need to try from 140 to 220. hope YOU THANK ME HERE is the Link http://m.blog.naver.com/kangmincraft/220675995736
http://m.blog.naver.com/kangmincraft/220626785379
debrick 140 https://drive.google.com/file/d/0BwKzoXanfz0jMFh1OXJ2QnROUWM/view
debrick 160 https://drive.google.com/file/d/0BwKzoXanfz0jemxYR0VNcnZULXc/view
debrick 180 https://drive.google.com/file/d/0BwKzoXanfz0jb2R4eGIzV1BHeGM/view
debrick 200 https://drive.google.com/file/d/0BwKzoXanfz0jUHBTelc4VzlQT2M/view
debrick 220 https://drive.google.com/file/d/0BwKzoXanfz0jZFBXaFRLMFJVWGc/view
try this, this is my own debrick lollipop: https://drive.google.com/file/d/0B09V79Pt4dCUSjF0ZUhNRWxiQ0k/view?usp=drive_web
Read this post who unbricked his dead mobile http://forum.xda-developers.com/showpost.php?p=66264994&postcount=14
just poweron the device after inserting the sdcard. check few times. try to go download mode.
use google translator if needed.
TIPS
sdcard miniumum 4GB, use old sdcards first. then latest memory cards, try sdcard memory higher than phone memory is advantage. try these 3 types.
debrick140 worked for most of them. try this first if you are on lollipop.
Lollipop bricked roms have higher luck.
after successful unbrick, use poweriso/ultraiso to format sdcard. i used poweriso>tools>cleanusb. then format in your pc.
ATTENTION MARSHMALLOW: IF YOU NO ROOT, NO CUSTOM TWRP, NO DOWNLOAD MODE. THEN THERE IS NO DEBRICK IMAGE YET. NOTHING WORKS. GIVE TO REPAIR RIFF,OCTOPUS BOX. THIS GUY SELLING SOUTION https: //www. facebook.com/ giaiphapandroid/. (remove spaces)IF BOUGHT, SHARE THE LINK HERE . i am not seller,i don't vouch anyone here. just helping so that you help others.
if you have friends in vietnam/korea ask them to search MM debrick and share here. if anyone have solution for MM. kindly share here.
SENIOR XDA: I REQUEST YOU TO CREATE DEBRICK FOR MARSHMALLOW.
THANK ME IF USEFUL....
Credits to Vega_Kangmin.
all copyrights to respective owners. i made simpler type. so if read all and google search, everything you can get in detail.
Click to expand...
Click to collapse
Hey, will this work on the D851?
If not, how do i create a debrick image for the D851?
Regards Mickey.
mickeyasamoah said:
Hey, will this work on the D851?
If not, how do i create a debrick image for the D851?
Regards Mickey.
Click to expand...
Click to collapse
only these can help you by software by money or assistance. just help. not vouch or i don;t get anything from this. your wish. remove spaces
androidbrick . com
https :// www. facebook .com/ giaiphapandroid
http :// www. vungoc -mobile. com/
if don;t wanna risk. better give to repair jtag/octoplus box which 100% fix this.
I have created a set of Windows scripts (.cmd files) to backup/restore selected partitions via emmcdl utility (a part of android-host-knife project).
Tested on RN3P but may be used with other Qualcomm-based devices.
emmcdl uses "firehose" module to interact with device's eMMC in 9008/EDL mode. With prog_emmc_firehose_8976_ddr.mbn from the "fastboot" firmware, can read/write partition table and any partition (including non-volatile ones, like modemst1/2, fsg etc.).
With this selected partition list, successfully restored phone's IMEI, MAC addresses and bootloader unlock status after accidental damaging the memory.
Can be used to create rawprogram0.xml file to flash images via MiFlash (recommended) or another Qualcomm utility.
!!! Not for beginners! If you don't know what is a "partition", "image" etc., please don't use this toolset until learning about that.
Do create a basic guide.
Will help a lot of em
Sent from my Redmi Note 3 using Tapatalk
Navi44 said:
Do create a basic guide.
Click to expand...
Click to collapse
Don't want to create a guide for beginners, like "click here and have fun". Since this process is dangerous, a user should have some knowledge, experience, and be careful.
emuzychenko said:
Don't want to create a guide for beginners, like "click here and have fun". Since this process is dangerous, a user should have some knowledge, experience, and be careful.
Click to expand...
Click to collapse
Some are ready to learn and take risks.
Anyways, it's all your choice.
Sent from my Redmi Note 3 using Tapatalk
I'm just trying to restore all partitions on my kate variant, i wiped every partition described in this thread:
https://forum.xda-developers.com/redmi-note-3/how-to/partition-layout-snapdragon-t3530412
It was an atempt to solve a weird bug after tons of flashes, i wiped them again and tried to flash the firmware using miflash in edl mode and nothing happens, it says flash successful but the phone is stuck booting in the MI logo part with the 3 dots.
My phone has locked bootloader, also i wiped those partitions performing an unofficial unlock.
I have the qcn file for the IMEIs.
The question... how to use the file from the OP's post?
If anybody can help me it will be appreciated.
Thank you for your time.
avercros said:
I'm just trying to restore all partitions on my kate variant, i wiped every partition described in this thread:
https://forum.xda-developers.com/redmi-note-3/how-to/partition-layout-snapdragon-t3530412
It was an atempt to solve a weird bug after tons of flashes, i wiped them again and tried to flash the firmware using miflash in edl mode and nothing happens, it says flash successful but the phone is stuck booting in the MI logo part with the 3 dots.
My phone has locked bootloader, also i wiped those partitions performing an unofficial unlock.
I have the qcn file for the IMEIs.
The question... how to use the file from the OP's post?
If anybody can help me it will be appreciated.
Thank you for your time.
Click to expand...
Click to collapse
It can take 10-15 minutes on first boot from miflash. if the dots are animated just go make some food and wait.
also make sure you do it like this : flash global stable FASTBOOT rom in edl mode with miflash, make sure you replace bootloader before you flash with unlocked one (emmc_appsboot.mbn) then reboot to fastboot when you see "successful" msg(hold vol down and power until you see fastboot), then "fastboot flash recovery recovery_zcx.img" then "fastboot boot recovery_zcx.img" i recommend zcx because it will automatically patch dm-verity... when zcx recovery boots, reboot to system. after you boot once into miui you can flash whatever recovery you want through twrp
the names are generic make sure to name your recovery image properly...
fastboot-edl to enter edl from fastboot mode - https://drive.google.com/open?id=0B2w-p-CP_G3FM1pCcG1JT0lfRUk
fastboot rom list - http://en.miui.com/a-234.html
zcx 917 - https://drive.google.com/file/d/0B2w-p-CP_G3FcHJRVTZHSjlNU3M/view?usp=drivesdk
unlocked emmc_appsboot.mbn - https://drive.google.com/file/d/0B2w-p-CP_G3FaXVFdWp1ODJOQm8/view?usp=drivesdk
miflash 64 bit with miphone drivers - https://drive.google.com/open?id=0B2w-p-CP_G3FRHR5UEp5TUMwemM
pabloa2 said:
It can take 10-15 minutes on first boot from miflash. if the dots are animated just go make some food and wait.
also make sure you do it like this : flash global stable FASTBOOT rom in edl mode with miflash, make sure you replace bootloader before you flash with unlocked one (emmc_appsboot.mbn) then reboot to fastboot when you see "successful" msg(hold vol down and power until you see fastboot), then "fastboot flash recovery recovery_zcx.img" then "fastboot boot recovery_zcx.img" i recommend zcx because it will automatically patch dm-verity... when zcx recovery boots, reboot to system. after you boot once into miui you can flash whatever recovery you want through twrp
fastboot rom list - http://en.miui.com/a-234.html
zcx 917 - https://drive.google.com/file/d/0B2w-p-CP_G3FcHJRVTZHSjlNU3M/view?usp=drivesdk
unlocked emmc_appsboot.mbn - https://drive.google.com/file/d/0B2w-p-CP_G3FaXVFdWp1ODJOQm8/view?usp=drivesdk
Click to expand...
Click to collapse
I tried this and the phone keeps stuck in booting.
I think that the last hope for this is a full partition repair or sell it for spare parts :/
avercros said:
I tried this and the phone keeps stuck in booting.
I think that the last hope for this is a full partition repair or sell it for spare parts :/
Click to expand...
Click to collapse
one final thing even though i mentioned it already, you must make sure your phone has dm-verity patched before you boot if you plan on using custom recovery. if you don't use zcx to automatically patch it then you need to install something like lazy patcher before you boot miui the first time. make sure you follow directions carefully. if your phone still isnt booting after 15 minutes (yes it can take that long) then you're out of luck, but i have a strong suspicion that your phone is not bricked.... a hard bricked phone will show no signs of life whatsoever, no leds, no screen, nothing. you must use testpoint method to enter qdloader mode at that point but your phone is not hard-bricked.
pabloa2 said:
one final thing even though i mentioned it already, you must make sure your phone has dm-verity patched before you boot if you plan on using custom recovery. if you don't use zcx to automatically patch it then you need to install something like lazy patcher before you boot miui the first time. make sure you follow directions carefully. if your phone still isnt booting after 15 minutes (yes it can take that long) then you're out of luck, but i have a strong suspicion that your phone is not bricked.... a hard bricked phone will show no signs of life whatsoever, no leds, no screen, nothing. you must use testpoint method to enter qdloader mode at that point but your phone is not hard-bricked.
Click to expand...
Click to collapse
Not working, i've done everything following your post, my phone only shows the MI logo and now it's blinking, it does not boot.
This is in the wrong section.
emuzychenko said:
I have created a set of Windows scripts (.cmd files) to backup/restore selected partitions via emmcdl utility (a part of android-host-knife project).
Tested on RN3P but may be used with other Qualcomm-based devices.
emmcdl uses "firehose" module to interact with device's eMMC in 9008/EDL mode. With prog_emmc_firehose_8976_ddr.mbn from the "fastboot" firmware, can read/write partition table and any partition (including non-volatile ones, like modemst1/2, fsg etc.).
With this selected partition list, successfully restored phone's IMEI, MAC addresses and bootloader unlock status after accidental damaging the memory.
Can be used to create rawprogram0.xml file to flash images via MiFlash (recommended) or another Qualcomm utility.
!!! Not for beginners! If you don't know what is a "partition", "image" etc., please don't use this toolset until learning about that.
Click to expand...
Click to collapse
Thanks for the thread..
Is there some insight to create "rawprogram0.xml" from this tool? I've try to execute it to see if there's any command list but only have "parttable.txt not found" message.
emuzychenko said:
I have created a set of Windows scripts (.cmd files) to backup/restore selected partitions via emmcdl utility (a part of android-host-knife project).
Tested on RN3P but may be used with other Qualcomm-based devices.
emmcdl uses "firehose" module to interact with device's eMMC in 9008/EDL mode. With prog_emmc_firehose_8976_ddr.mbn from the "fastboot" firmware, can read/write partition table and any partition (including non-volatile ones, like modemst1/2, fsg etc.).
With this selected partition list, successfully restored phone's IMEI, MAC addresses and bootloader unlock status after accidental damaging the memory.
Can be used to create rawprogram0.xml file to flash images via MiFlash (recommended) or another Qualcomm utility.
!!! Not for beginners! If you don't know what is a "partition", "image" etc., please don't use this toolset until learning about that.
Click to expand...
Click to collapse
Thanks man !
This tool was a big help for my other device (LYF) based on qualcomm.
it's one of a kind..couldn't find anything similar & easy on internet.
don't know why this thread is not popular given that lot of people want the things this tool can easily do, may be they are reluctant to go over edge and try on own.
Anyway thanks a lot again & Keep good work
Qullcomm device
Hello sir I have erased perist on my device accidentally and my device is Redmi 4x I have tried to restore my persist partion on my device via emmcdl utility when I enter first command emmcdl -1
It's show my device port com 5 and when I entered second command
emmcdl -p COM5 -f prog_emmc_firehose_8937_ddr.mbn -e persist -o persist.img it's showing error failed to write hello response back to device and didn't receive Sahara hello packet from the device and some thing like that. the error also show when I disconnected my device from pc. Please anyone help me.thankyou
Dbdbsss said:
Hello sir I have erased perist on my device accidentally and my device is Redmi 4x I have tried to restore my persist partion on my device via emmcdl utility when I enter first command emmcdl -1
It's show my device port com 5 and when I entered second command
emmcdl -p COM5 -f prog_emmc_firehose_8937_ddr.mbn -e persist -o persist.img it's showing error failed to write hello response back to device and didn't receive Sahara hello packet from the device and some thing like that. the error also show when I disconnected my device from pc. Please anyone help me.thankyou
Click to expand...
Click to collapse
Have u unlocked ur bootloader.
If yes then
Put phone in fastboot mode.
Flash persist img using fastboot command
fastboot flash persist persist.img
Or use advance twrp and flash persist.img in persist partition.
rawprogram0.xml
how to create a rawprogram0.xml which contains all partitions?
i am much willing to learn more about this,
feel free to message me in fb
facebook.com/samuel.tajuda
When I tried to Restore a Backup Userdata.img to my Zenfone, It requires me a Startup Password that I've not currently set on. (I only used Lockscreen and Google's Default Password but nothing happens)
Does somebody know the Encrypted Password made by QCPart or How to Unpack the Disk Image File that only shows Unallocated on Linux Reader for Windows?
I have some important files that I need to retrieve from the Bricked Phone that I backup with it before I Flashed the Android ROM with Clean Firmware
I've got a Moto e4 Qualcomm xt1768 (non-Amazon ads version) which I had previously successfully unlocked the bootloader on and rooted. Was messing around recently and managed to (I think) ruin the partition table. It no longer gives any indication of powering on, but if I plug it into a computer right after popping the battery out and in again it's showing up in HS-USB mode as a Qualcomm HS-USB QDLoader 9008. From my research it seems like, with the correct files, I could recover by either flashing something via QFIL (some kind of firehose image?) or possibly getting into fastboot by dd writing a full emmc backup of a working device to an SD card. Unfortunately I don't have either of those things for this device.
If anyone has either of those things already, or might be willing to do a dd dump of their xt1768 for me to try the SD card method, or has other information for me that would help me recover the device, I would be forever grateful.
You need a stock firmware to revive your phone and nothing else. As far as it is detected by computer.
I tried the sdcard dump method and it did not work. Without a new leaked image the new e4 cannot be restored from the qualcomm bootloader.
Heres the loader.img i made before my phone was bricked. If you find a way to use this or a blankflash file that works with our phone please let me know
https ://mega.nz
/#!GTBXnIRR!2SA6PaaEvfqpJ4sG4a3yD-CFlrTrloR9j40CVpcw26c
@rudism Someone found a blankflash for xt1767, which works on the xt1768.
Follow the xt1767 instructions here
https://forum.kingfirmware.com/thread-Moto-E4-XT1766-XT1767-Dead-Boot-Repair
You can use the driver.cab from
https://forum.xda-developers.com/moto-z/how-to/guide-how-to-unbrick-moto-z-hardbricked-t3590133
then download
https://androidfilehost.com/?fid=1322778262904008165
and flash the individual paritions via fastboot
Awesome! Can confirm that this worked and brought my bricked xt1768 back to life. Thank you!
Sorry to bump, but I also wanted to confirm that this worked for me as well. Did a successful restore but didnt realize that the firmware version I downloaded had an older bootloader so it bricked my phone. Finally found this post and all is well again!
xeropressence said:
@rudism Someone found a blankflash for xt1767, which works on the xt1768.
Follow the xt1767 instructions here
https://forum.kingfirmware.com/thread-Moto-E4-XT1766-XT1767-Dead-Boot-Repair
You can use the driver.cab from
https://forum.xda-developers.com/moto-z/how-to/guide-how-to-unbrick-moto-z-hardbricked-t3590133
then download
https://androidfilehost.com/?fid=1322778262904008165
and flash the individual paritions via fastboot
Click to expand...
Click to collapse
Help me My friend
I need the Blankflash file for the xt1767 / xt1768 I have my phone in hard brick, I need to start it in fastboot mode. help me with the file as I can't find it.
Does anyone has any instruction for XT1762 ?
What I did I have installed Lineage 14 on it and it worked well, then I found a 16 version and wanted to install it. After that it would not boot into anything. Didn't help to reinstall 14 or wipe or anything. Then I downloaded a factory image, but it might have been the wrong one and I flashed all the files preloader, boot, oem, system, etc. After that it would not do anything. Now if I plug it in the computer I only see the white LED on, and if I press long the power button then in "lsusb" it shows up for 2 seconds as MediaTek Inc. MT65xx Preloader.
Is it still possible to recover it? I would greatly appreciate any help.
First of all, thanks for all the people here provide very useful message.
Acutally I encouter a lot of similar issues across the posts.
Please refer to the posts here:
Unbrick guide Z00l Ze550kl
Need QCN file for ZE550KL/Z00L (2GB Ram) Please.
[Solved]Stuck on logo when booting into custom ROM( Zenfone 2 laser ZE550KL Z00LD)
My model is ZE550KL 2GB/16GB version.
What need to be prepared (please look around from google)
1. CSCImage for recovery
2. QPST 2.7
3. Workable QCN, if you have no backup please make one from the other post. (you will need imei coverter and HxD)
4. Retail image WW_ZE550KL_1.17.40.1234-rel-user-20160304185904-secured-releaseAFT_QC
5. Offical latest image
6. TWRP
7. Minitool Partition Manager (I tried diskpart but not working, so please use this one)
8. Qualcomm Driver
Here are the procedures for reference (I do this for over 10 times and 3 nights)
Please make sure you have working QCN...otherwise you cannot recover the calling feature.
1. Erase aboot
fastboot_8916 erase aboot
use above command to erase the partition
you can unplug the battery and cable and replug them.
or simply use fastboot reboot command.
Result: Device enter into 9006 mode
2. Open Minitool Partition manager
Right click and Delete all partition.
Create one single partition using ext4 format
Once done, remove the battery and cable, replug them.
Result: Device enter into 9008 mode
3. If you installed QPST, you should have a program called QFIL
Please use it and extract the firmware from CSCImage, it should have all the items except emmc MBN, just copy it from the root folder.
If you do this correct (follow other post for more detail)
Replug the device will give you a fastboot screen
Result: Device with workable fastboot
4. Now you have a clean bootloader, but no other thing
Go to CSCImage and click flashall
Once it is done, all the partitions will be ok (sometimes I got /factory not mount, let's fix this later)
Result: you will have a engineering OS and bootloader unlocked, diag mode natively enabled.
5. Open Software Downloader from QPST, and recover the QCN, it will reboot the phone.
If you are not doing this correctly (and many issues here), you will get bootloop.
And you have to start over again.
My suggestion is do not touch any of the bootloader setting. (so do not try to use unofficial bootloader unlock guide)
Even you give a command like "fastboot oem adb_enable" it will cause a bootloop and have to start over.
So my suggestion is not touch any bootloader setting
Result: The phone calling and data should be recovered. You can test by making some call.
6. If you want to keep your bootloader unlocked, the retail image flashall you can search there is a "oem lock"
change to unlock and run it in fastboot mode.
Result: You will have a bootloader unlocked phone, with WW firmware.
You can start from here to do TWRP.
to fix /factory partition. you can install busybox and in adb shell, use mkfs.vfat for the partition.
What is CSCImage, I tried your method but got stuck on missing partitions. (Boot, Recovery, System, etc..)
christian.arvin said:
What is CSCImage, I tried your method but got stuck on missing partitions. (Boot, Recovery, System, etc..)
Click to expand...
Click to collapse
This means you didn't unlock your bootloader.
bootloader needs to be unlocked to flash the partition file, and then the partition will be recovered without data.
My bootloader was unlock.
I digged deeper in your method. And this is what i understand and let it be an information for those who will try.
Back up all partition before you delete all partitions. (Your serial and other sensitive data are stored in some of this partition)
Your method only restore 5 partition table that is inside the main0 gpt mbn.
Note: the whole partition table is listed in the both0 gpt mbn.
In my stupidity I renamed the both0 gpt to main0 gpt thinking that it would work. Instead I run into an unstoppable bootloader bootloop.
In an ending note my ZF2 Laser's only hope is a full eMMC reflash that requires external methods. Or let the official professionals handle it.