Related
Yesterday i flashed my Jiayu S3 to lolipop (i tought) and i just bricked my phone!
After reboot it was just dead.. when i plug into pc with USB i hear the connect sound and after 2 seconds the disconnect sound. This keeps on going until i pull the USB plug. When i look in DeviceManager i see it refresh after every sound, but nothing pops up (unknown device or whatever). I deletet all usb drivers with usbdeview, restart pc but still no changes.
I tried with or without battery, but without it does nothing at all.. i tried holding Vol+ or - or both or with power button, but nothing.
Read some threads about unbrick and install correct usb driver for jiayu s3, but all the options they came with does not work on my device!
I'm a little despered now and don't know what to do.. i get the feeling that my 2 weeks old phone is dead? :'(
My pc has windows 7
Did the flash with SP Flashtool 5.1516
Did not untick preload in flashtool, i guess i got the wrong preload or something??
Please help!
No one..? :crying:
Lowrida said:
Yesterday i flashed my Jiayu S3 to lolipop (i tought) and i just bricked my phone!
After reboot it was just dead.. when i plug into pc with USB i hear the connect sound and after 2 seconds the disconnect sound. This keeps on going until i pull the USB plug. When i look in DeviceManager i see it refresh after every sound, but nothing pops up (unknown device or whatever). I deletet all usb drivers with usbdeview, restart pc but still no changes.
I tried with or without battery, but without it does nothing at all.. i tried holding Vol+ or - or both or with power button, but nothing.
Read some threads about unbrick and install correct usb driver for jiayu s3, but all the options they came with does not work on my device!
I'm a little despered now and don't know what to do.. i get the feeling that my 2 weeks old phone is dead? :'(
My pc has windows 7
Did the flash with SP Flashtool 5.1516
Did not untick preload in flashtool, i guess i got the wrong preload or something??
Please help!
Click to expand...
Click to collapse
so you cannot boot into recovery or fastboot either?
Lowrida said:
Yesterday i flashed my Jiayu S3 to lolipop (i tought) and i just bricked my phone!
After reboot it was just dead.. when i plug into pc with USB i hear the connect sound and after 2 seconds the disconnect sound. This keeps on going until i pull the USB plug. When i look in DeviceManager i see it refresh after every sound, but nothing pops up (unknown device or whatever). I deletet all usb drivers with usbdeview, restart pc but still no changes.
I tried with or without battery, but without it does nothing at all.. i tried holding Vol+ or - or both or with power button, but nothing.
Read some threads about unbrick and install correct usb driver for jiayu s3, but all the options they came with does not work on my device!
I'm a little despered now and don't know what to do.. i get the feeling that my 2 weeks old phone is dead? :'(
My pc has windows 7
Did the flash with SP Flashtool 5.1516
Did not untick preload in flashtool, i guess i got the wrong preload or something??
Please help!
Click to expand...
Click to collapse
Just flash it again, but this time with "Firmware upgrade " in SP Flashtool instead of "Download". Change from KK to LL needs reepartitioning, so firmware upgrade.
The reason why you don´t "see" the S3 any longer on the pc is, that the USB storage mode from KK, which is driverless for windows, don´t work right now on LL.
Once flashed to LL you will need to install a driver, for windows to connect to the S3.
@ Dior DNA:
No i can't. Phone does nothing with the buttons. Only diference if i hold Vol - then time from connect sound and disconnect sound is a little longer.. about 10 seconds. But still nothing happens.
@1testi:
Flashtools can't see my phone. I tried it a hundred times. With battery, without battery, with Vol - and with Vol +.
When i connect the USB cable i hear the connect sound and after 2 a 3 seconds i hear disconnect sound. This goes on and on until i pull the USB cable out. In devicemanager i see a refresh going on, but nothing pops up.
I'm realy despered on what to do now?
Lowrida said:
@1testi:
Flashtools can't see my phone. I tried it a hundred times. With battery, without battery, with Vol - and with Vol +.
When i connect the USB cable i hear the connect sound and after 2 a 3 seconds i hear disconnect sound. This goes on and on until i pull the USB cable out. In devicemanager i see a refresh going on, but nothing pops up.
I'm realy despered on what to do now?
Click to expand...
Click to collapse
Why the SP Flashtool isn´t working any longer? You didn´t deinstalled the driver, did you? Just try to flash again with "Firmware Upgrade".
I don´t know a way to reinstall the driver in windows without the preloader. The only thing you can do, as far as i know, is to use a linux
pc to flash again. Linux don´t need a driver for SPF, only some rules.
Lowrida said:
@ Dior DNA:
No i can't. Phone does nothing with the buttons. Only diference if i hold Vol - then time from connect sound and disconnect sound is a little longer.. about 10 seconds. But still nothing happens.
(
Click to expand...
Click to collapse
Booting into recovery or flashtool I meant regardless of pc and/or spflashtool.
If I recall correctly:
hold volup and power boots recovery
hold voldn and power boots flashtool
If you can boot recovery then which one is it? Maybe you can restore something or manually flash preloader bin from there.
After the flash i reboot and then the connect and disconnect sound appears. So i tried differend things, but could not connect. I wanted to flash again, but flashtool did not reconice the phone and nothing in DeviceManager. That's why i thought to remove the driver and try to re-install it. But that did not help..
Holding Vol - or + button with power button or both Vol buttons with power button does nothing.. i tried to hold all combinations at least 30 seconds, but nothing at all.
I have no Linux pc or any knowhow to make a Linux pc.. or a pc to install Linux on..
One last thing you can try: remove the battery, wait a little, insert the battery again. Hold vol+ key, keep holding it and press power
button, while still holding the vol+. If you don´t see anything happening then you bricked the phone.
You will need help from a professional or at least from someone with a linux machine, sorry.
I'll try that.
You have any idea what could have caused the brick?
As i wrote above, moving from KK to LL with wrong parameter "Download" in SPF.
....and a not working recovery.
You should try this method :
darmowyinternet.net/forum/temat-poradnik-jak-uruchomic-uceglony-telefon-po-wgraniu-zlego-romu-test-point_383
unfortunately you have to translate before
Ok i tried that site with google translate and i could a little make up what they are saying.
But that is a very drastically operation, and i would like to give it some other tries before dismantling my phone.
So i googled and googled.. came here: http://forum.xda-developers.com/showthread.php?t=889128
Had enough electronics lying around from my former 27mc hobby, so searched for the right resistors,
cut up a micro usb cable and give it a try... well.. nothing! Tried for about an hour and gave up.
Then i googled on Unbrick Jigs, but for what i read they are only for Samsung phones, so i gues the trick
with the resistors were also?
So googling again... came here: http://forum.xda-developers.com/showthread.php?t=2454004
Reading the tread and the comments, someone mentioned a download for "Mediatek Driver Auto Installer".
Downloaded that and installed the drivers. Plugged in my phone and... whoohoo!! Something is happening! :silly:
My devicemanager saw an "Alcatel single RNDIS interface". I unplugged and plugged my phone a few times to
be sure it was my phone. Sooo... one step further! :good:
Then i googled on this device.. came up with all sorts of network devices, not helpfull. Then googled on Jiayu with
this device. Came up with this tread: https://www.china-devices.com/topic...vcomm-drivers-onto-your-pc-win-7vistaxp-only/
It's a tread about bricked Jiayu G3 devices, but i thought, 'What the heck, lets give it a try!'.
I downloaded the "MTK Megapack - All Tools Here!" and unpacked. Wend back to device manager and manually updated the driver
of the Alcatel device. Show all devices - browse - wend to Megapack map and there were MTK drivers for the 65xx device.
And yess.. when i plug in my phone there's the device: " MTK USB Port (COM7) "
SP Flashtools sees my phone again! :good:
Tried to flash a stock preloader, but got an error: "BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) – [EMI] Enable DRAM failed!"
But for now that's a problem for tomorrow.. it's almost 2:30 and i have to got some sleep!
(sorry for the misspellings or telling things not clear, i'm tired and english is not my main language)
Grats!
You can google the error. This leds you in the right direction.
It's alive!!!!!! :laugh::silly::victory:
Because the kitkat stockrom i downloaded gave me the same error over and over i searched for something else.
So i downloaded TF Extreme lolipop 5.1 this morning and give it a try. And all went well. I pulled the usb plug and
pushed power button.. only vibration but nothing. Then pulled the battery and after few seconds put it back in
and try power again. Only 1 vibration.. then tried Vol + and - combinations but nothing. (dammn!)
Then plug the usb in and i saw the battery icon.. it was total empty! (because of a week trying).
So now it's charging and i hope it starts, can't wait!!
Thanx all for the effort in helping me out! :good:
Edit: Ok, so i could not wait and hit power! It shows green screen with Jiayu S3 logo and text "New Load". So i guess it's prepairing for first startup!
my s3 basic is not charging when on.. also when connected to pc thru usb, ipc shows device malfunctioning ,and there is no indication on phone..I try to connect to sp flash tool also no success..same error"usb device not recognized pops up every 2s.everything else is fine..Any method to upgrade to 5.1 now on official kk
Kinda need help, happened something similar
It happened something similar to me.
I flashed the whole ROM, bootloader included, I was very sure that my model, Jiayu S3 3GB ROM + 32GB RAM, was the correct, but still bricked my phone.
There's no problem at all when I plug it into my PC, I installed the lastest MTK drivers on windows 10, having to disable the signature enforcement.
The problem comes when I start flashing. I only mark the bootloader, then I press "Download" (on the lastest version of SP Flash Tools), and plug the phone, with the battery in it (I've tried without battery, pressing all possible combinations and does nothing), when I plug it in with the battery and pressing no buttons, the driver is detected as MTK USB Port. That's a good thing I guess. But It does not pass from the red bar, and gives me the known error "Enable DRAM Failed".
I've tried to google any possible solutions, reinstalling other version of the MTK drivers, on different versions of Windows, with other versions of official ROMs, and the result is always the same.
The only thing that's left to try is flashing it with an Ubuntu machine, which is something I do not expertise to be honest, but I'm gonna gather some info and try to do it.
However, if someone has any idea of what I might be doing wrong (excluding the part when I flashed the bootloader, I'll never do it again), I would be really grateful for any kind of help.
Thank you!
Kiei said:
It happened something similar to me.
I flashed the whole ROM, bootloader included, I was very sure that my model, Jiayu S3 3GB ROM + 32GB RAM, was the correct, but still bricked my phone.
There's no problem at all when I plug it into my PC, I installed the lastest MTK drivers on windows 10, having to disable the signature enforcement.
The problem comes when I start flashing. I only mark the bootloader, then I press "Download" (on the lastest version of SP Flash Tools), and plug the phone, with the battery in it (I've tried without battery, pressing all possible combinations and does nothing), when I plug it in with the battery and pressing no buttons, the driver is detected as MTK USB Port. That's a good thing I guess. But It does not pass from the red bar, and gives me the known error "Enable DRAM Failed".
I've tried to google any possible solutions, reinstalling other version of the MTK drivers, on different versions of Windows, with other versions of official ROMs, and the result is always the same.
The only thing that's left to try is flashing it with an Ubuntu machine, which is something I do not expertise to be honest, but I'm gonna gather some info and try to do it.
However, if someone has any idea of what I might be doing wrong (excluding the part when I flashed the bootloader, I'll never do it again), I would be really grateful for any kind of help.
Thank you!
Click to expand...
Click to collapse
Oeps it might be the same problem with the 32GB version as I have.
See http://forum.xda-developers.com/showpost.php?p=68036678&postcount=295
I am waiting for a stock ROM backup.
I have learned to never flash the original preloader again.
xtyphoon said:
Oeps it might be the same problem with the 32GB version as I have.
See http://forum.xda-developers.com/showpost.php?p=68036678&postcount=295
I am waiting for a stock ROM backup.
I have learned to never flash the original preloader again.
Click to expand...
Click to collapse
You're right, with the 32GB rom version (which is still unavaliable for public use) it worked! I still got it here, so anyone feel free to ask me the link too.
Thanks to xtyphoon and Dior DNA and everyone who made this possible, if you ever come to Girona city, I'll buy you a drink ;D
Kiei said:
[...]if you ever come to Girona city[...]
Click to expand...
Click to collapse
I was around there few weeks ago
No Boot - No Recovery - No Download Mode Unbrick Guide
Qualcomm HS-USB QDLoader 9008 or Secure booting error (No Boot - No Recovery - No Download Mode) or "QHSUSB_BULK"
Hi team, if you have come here I'm sorry you are having this problem! But my friend and I have been to hell and back trying to fix this problem and we wanted to share our method of success for any poor soul who is experiencing the same thing! For our situation the USB was unplugged half way through flashing a KDZ or going back to stock firmware and created the No Boot - No Recovery - No Download Mode problem.
This has only been tested on the D855.. Just so you know.
First off, here are some links which you may need to have a look at if you have not done so already. Most of the bricking problems have already been extensively talked about by people here on XDA. For the method that works, we had to pull information from everywhere and spent a long time looking for the solution.
How to go back to stock - http://forum.xda-developers.com/showthread.php?t=2785089
Link for TOTs and KDZ's from the above thread - http://storagecow.eu/index.php?dir=Xda/LG+G3/Stock/
The Main Fix for the problem - http://forum.xda-developers.com/lg-g3/general/fix-unbrick-lg-g3-stuck-qualcomm-hs-usb-t2933853
The G2 version of the fix (for reference if you still have problems 55+ pages) http://forum.xda-developers.com/lg-g2/general/fix-unbrick-lg-g2-stuck-qualcomm-hs-usb-t2933830
This is your last stop shop if everything is broken and nothing works, involves hardware fix - http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359
The problem we encountered several times with all of the described methods above, is that many do not describe important things. While the main fix thread for the Qualcomm HS-USB QDLoader 9008 mode, which is shown in device manager, is very well written and detailed, the programs which are linked in this thread are questionable and haven't worked for many users with some offering to fix for money. We searched the internet and located a working version of the program which worked without giving a "Device was not found in dload trying to flash programmer" like the one provided on the XDA page. Use the links below for a working version from this thread http://androidforums.com/threads/lg-g2-not-turning-on-help.916865/
My first point is if you are having problems with any of the things, CHANGE YOUR USB CABLE or use the stock cable (I know most experienced users know this). The reason for this problem has something to do with different USB cables being made for different purposes and are of different qualities. Having an error on the USB ports gave us only qhsusb_bulk on windows device manager, without Qualcomm HS-USB QDLoader 9008 as well.
If you are still having problems, check your USB ports. It is really important to make sure this isn't the problem or you will be trying to fix this problem endlessly.
First attach the USB cable to the computer. When you plug your phone in, make sure you attempt to enter download mode by holding the volume up button when you plug the USB into your phone. Even though the phone will not enter "Download Mode" It will allow the phone to be detected by your computer (at which point you can release the buttons, it should then show "Qualcomm HS-USB QDLoader 9008" under ports. If this is not displayed you have a problem with the USB cable or port, or your phone is hard bricked and you need to head to the above guide for the hardware fix. If you have followed so far and are wondering what to do from here, once the "Main Fix" guide ends, head over to the "How to go back to Stock" thread above. Your phone should be showing "firmware upgrade" and you can proceed to flash a new updated KDZ on your device then everything will work and your nightmare should be over!
Working Boarddiag - https://drive.google.com/file/d/0BzkqP9M0LLWQUkEyRkZrVHlEbDg/view
Qualcomm USB Drivers (Essential for the aforementioned "Main Fix" above) - https://drive.google.com/file/d/0BzkqP9M0LLWQblF6Vl9OcUkwUDA/view
LG United Drivers (Phone Drivers) - https://drive.google.com/file/d/0BzkqP9M0LLWQUURDTHlYOW5YRms/view
If this helped you to fix your nightmare don't forget to hit the thanks button!
The "Wroking Boarddiag" asks for PW. aside from that, very good find, thanks
detected as qdloader hs usb 9008
board diag- ap check failed device not in downld mode
For all people with Windows 10 an problems with drivers (device is detected by Windows but app is not connecting). Decompress de correct cab for your Windows version, and update the driver "Qualcomm HS-USB QDloader 9008" with the path you used to extract. Now this driver isn't advertising that isn't signed anymore, and all apps will connect with your LG G3
Qualcomm HS-USB QDLoader 9008 2.1.0.5 x86
Qualcomm HS-USB QDLoader 9008 2.1.0.5 x64
Hi, I have the same problem, except that when I connect the usb, it shows up as "LGE AndroidNetUSB Serial Port". I'm not sure if I should try the Qualcomm route?
MrMuli said:
Hi, I have the same problem, except that when I connect the usb, it shows up as "LGE AndroidNetUSB Serial Port". I'm not sure if I should try the Qualcomm route?
Click to expand...
Click to collapse
I just fixed my Lg g3 with this method. Not sure if it will work with AndroidNetUSB
Would like to help for any difficulties. (e.g. Not able to find TOT file) etc.
Thanks to @Orcam & @kryptonite
This did not work. Here's what I tried:
1. Without battery
2. Changed drivers as @shawe_ewahs says
3. With battery
4. Admin and non-admin
5. Changing COM ports
But, every time, I get:
"Device was not found in dload trying flash programmer
TEST Aborted!!"
My LG G3 D851 is in Qualcomm HS_USB QDLoader 9008 (COM 41) so I know it is in the correct mode! Agh, it is very frustrating. Any help is appreciated. Thanks.
Thanks you SOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO much! <3 I finally was able to fix my device *O*
furiify said:
Thanks you SOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO much! <3 I finally was able to fix my device *O*
Click to expand...
Click to collapse
No problem. Hope it didn't take you as long as it took us to find all the right stuff
I'm having this problem, but when I plug in without a battery all that shows up in device manager is "Unknown USB Device (Device Descriptor Request Failed)". I tried to do the hardware fix and was able to force the device to reboot by touching the pins. But all that happens is it disconnects and reconnects from USB without being detected properly.
I should note that when I turn the phone on right now, it stays stuck in the initial LG G3 splash screen. When I plug in without a battery, it shows an empty battery icon with a wire and a triangle question mark.
Any idea what I'm doing wrong? I think if I can just figure out how to get my machine to detect my phone as the qdloader hs usb 9008 I can figure out the rest.
The boarddiag v3.99 version 1 and 2 dont work, they dont even get ejecuted, not eve trying to execute as administrator.
Just wanted to reply since I resolved my issue. It turned out that, despite the apparent inability to boot into download mode, I discovered that if I booted up the phone with a battery in it and plugged into a windows 7 laptop, and held the button down to enter download mode, it eventually let me into download mode. I really can't explain why this worked, but just wanted to put it out there. It was at least a few minutes before I noticed that the laptop chirped and it was showing the install screen in download mode.
Hope this helps someone out.
Dr1t3r said:
The boarddiag v3.99 version 1 and 2 dont work, they dont even get ejecuted, not eve trying to execute as administrator.
Click to expand...
Click to collapse
phaim said:
Just wanted to reply since I resolved my issue. It turned out that, despite the apparent inability to boot into download mode, I discovered that if I booted up the phone with a battery in it and plugged into a windows 7 laptop, and held the button down to enter download mode, it eventually let me into download mode. I really can't explain why this worked, but just wanted to put it out there. It was at least a few minutes before I noticed that the laptop chirped and it was showing the install screen in download mode.
Hope this helps someone out.
Click to expand...
Click to collapse
Sounds like it may be a problem with windows from what you two have said. Perhaps compatibility mode is the way to go. They did release a pretty major windows 10 update since I posted this guide.
Okay so long story short: I unlocked my bootloader, flashed twrp and things like that and tried to flash lineage. This was all using the Axon 7 tool. I did something wrong and now I can't get into any other mode but EDL mode. The phone shows up in Miflash but I always get some "cant read hello packet error" and it tries to "reset" and end it eventually just stops and gives me an error. Plz help.
daevion0 said:
Okay so long story short: I unlocked my bootloader, flashed twrp and things like that and tried to flash lineage. This was all using the Axon 7 tool. I did something wrong and now I can't get into any other mode but EDL mode. The phone shows up in Miflash but I always get some "cant read hello packet error" and it tries to "reset" and end it eventually just stops and gives me an error. Plz help.
Click to expand...
Click to collapse
I assume you're not on Windows 10 x64? If you aren't, either get a PC with Win10 x64, or do this:
Connect the phone, get into EDL mode. Now go to the Device Manager, and tell me where it appears.
It can appear as:
-"Qualcomm HS-USB QDLoader 9008" under Ports (COM & LPT);
-"ZTE DFU Interface, under Ports too; or
-"QUSB_BULK" under Universal Serial Bus devices or unknown devices.
If it appears as the DFU stuff, you'll have to follow the 4th category brick repair guide. If it appears as QDLoader, right click on it, then Properties, then go to Bits per second and put the number at 115200 or 128000 if it's not there. Then hold the 3 buttons (vol and power) until Windows beeps and the device manager spazzes and the phone flashes the red led, then try MiFlash again.
If it appears as QUSB_BULK, uninstall the driver (tick delete driver software too) and restart edl.
Choose an username... said:
I assume you're not on Windows 10 x64? If you aren't, either get a PC with Win10 x64, or do this:
Connect the phone, get into EDL mode. Now go to the Device Manager, and tell me where it appears.
It can appear as:
-"Qualcomm HS-USB QDLoader 9008" under Ports (COM & LPT);
-"ZTE DFU Interface, under Ports too; or
-"QUSB_BULK" under Universal Serial Bus devices or unknown devices.
If it appears as the DFU stuff, you'll have to follow the 4th category brick repair guide. If it appears as QDLoader, right click on it, then Properties, then go to Bits per second and put the number at 115200 or 128000 if it's not there. Then hold the 3 buttons (vol and power) until Windows beeps and the device manager spazzes and the phone flashes the red led, then try MiFlash again.
If it appears as QUSB_BULK, uninstall the driver (tick delete driver software too) and restart edl.
Click to expand...
Click to collapse
I'm on win10 64bit
daevion0 said:
I'm on win10 64bit
Click to expand...
Click to collapse
Then do everything I described above or just try another PC. It always happens that one PC can be decided not to let you unbrick your phone for some reason
Choose an username... said:
Then do everything I described above or just try another PC. It always happens that one PC can be decided not to let you unbrick your phone for some reason
Click to expand...
Click to collapse
Is there no other option? is there no other way to at least get fast boot mode back on my phone?
daevion0 said:
Is there no other option? is there no other way to at least get fast boot mode back on my phone?
Click to expand...
Click to collapse
Lol nope, not if EDL is not working for you. You still didn't tell me whether you have a DFU brick or not. If you do have a DFU brick the only surefire way is to disassemble your phone and short a testpad, so don't complain.
Try what I told you above. It may be that it's set at 9600 baud
daevion0 said:
Okay so long story short: I unlocked my bootloader, flashed twrp and things like that and tried to flash lineage. This was all using the Axon 7 tool. I did something wrong and now I can't get into any other mode but EDL mode. The phone shows up in Miflash but I always get some "cant read hello packet error" and it tries to "reset" and end it eventually just stops and gives me an error. Plz help.
Click to expand...
Click to collapse
1. You must use "Qualcomm HS-USB QDLoader 9008" driver (there is another one call zidag but it's not work here)
2. As soos as you enter EDL mode, you must press "Flash" as quick as possible
i'm in a similar situation... i did "fastboot oem lock" and now i'm in a loop trying to boot the phone, after the 3time it enters edl (i see the red light).
My model is de G model (2017G) can i use miFlash just to restore the recovery and fastboot?
i had installed lineageOS, when connecting my phone it says that is the U model (2017U) but i think is only a label tag from the rom...
Thansks for the help!!
A 64 bit computer is not really necessary, however it is adviced.
I used a 32bit laptop running Win 10 to rescue mine.
Drivers seem to be a major problem, having the correct up to date drivers is a must.
Also try using Edl Tool and the Axon7 tool kit to access flashing.
Zadig drivers can help in some instances.
With the error you are receiving, have you tried another Edl package?
I was using an Edl package that would not finish flashing either, try a different package and make sure its correct for your phone.
I hope you get it sorted
The hello read package does occur when the phone is not really EDL mode anymore. You always have to restart the phone and boot manually into EDL mode with + - Power and you have to reboot everytime you did or if the hello error happens.
Look under device manager if it says Qualcomm instead of ZTE Device Handset. If that is the case you can build your own EDL cable.
"First I opened the cable and cut the Black and green open, then I connected all the black and green one together and pressed the power button until the red led was gone and 2 additional seconds.
After that I disconnected the modded cable and connected the Phone to the PC with the orginal cable and it showed up as Qualcomm HS-USB QDLoader 9008. "
You can install the qualcomm drivers under the MiFlash tab in the latest version.
i finally solve my issue following the guide: https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898 there is also a resume on https://forum.xda-developers.com/axon-7/how-to/guide-dfu-unbrick-guide-disassembly-t3731152
Three days ago, my phone went off by itself and I had a hard time starting again, it was just loading the bootanimation, I tried to reinstall the ROM, but it did not go into TWRP, although the message Recovery appears on the screen, I insisted and after several attempts, I got into the recovery, formatted everything and I installed the AICP ROM again, and I had to restart,my phone freezes in the LeEco bootloader, then again I insisted until the ROM finally started, but soon realized that it was taking too long to start (30 minutes waiting and nothing).
So I rebooted again, and from then on, I can not go into any mode anymore, trying to access the TWRP, the phone only stays on the Recovery screen until reboot after 2 minutes, when letting the phone try to start the ROM, it only stays on the LeEco screen and restart after 2 minutes, when entering Fastboot, it enters the screen in Fastboot mode, but is not recognized by the computer, not even as unknown device, the same for Download mode.
Is there anything I can try?
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
tsongming said:
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
Click to expand...
Click to collapse
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode.sl Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Well that sucks, if you feel like sending to the phone to China for repair, you can find several shops that are offering to repair any damaged Leeco for $10 and an average cost of $30 for resoldering. On the TaoBao website, use Chrome for translation. Some of their ads mention overseas repair
If it's memory it would be an easy fix for them.
If you don't want to fix it, I highly recommend the Mi8 if it's within your budget, its a perfect phone and you can find them for close to $300. My brother has a Redmi note 6 Pro which is also really nice. He paid $190.
Good Luck.
Sent from my Xiaomi MI 8 using XDA Labs
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Check out this possible do it yourself fix : https://forum.xda-developers.com/showpost.php?p=79302729&postcount=71
Background:
OnePlus 8 Pro IN2020
Original OS version is OxygenOS 12 Android 12
How my phone turned into brick:
Try flashboot unsupported TWRP and other third party recoveries.
After a few tries, eventually causing my phone turning into a brick
What my error looks like:
Not able to boot into system
Showing "the current image(boot/recovery) have been destroyed"
Can access fastboot and detect by system
Method:
Follow the steps in How to UNBRICK OnePlus 8 or 8 Pro! by Max Lee (Thank you my man, Max, for this video)
Pitfalls in 2022 (IMPORTANT before UNBRICK!):A USB 2.0 and Third-party USB cable are highly recommendedI was unable to boot into Quadcomm EDL mode while using the stock cable and USB 3.0 connector. Pressing the correct Volumn Up & Volumn Down and Power Button will boot the phone to fastboot in no time.
I successfully got into the EDL mode and finished flashing the phone using my iPad Pro Type-C charging cable which is an USB 2.0 one.
Use a newer version of the Qualcomm driver if you find the device not correctly detectedUse Qualcomm HS-USB QDLoader 9008 driver.
A new Quadcomm driver will help you flash your device correctly the first time!!!
Windows 11 won't let you install unsigned driver by default, but there's a way round
Press Shift key while click Reboot in start menu to enter Advanced Options
Click Trouble shoot in Advanced Options
Click Advanced options, click Startup Settings then click Restart
After restart press 7 when required
If your computer won't restart, just unplug your phone temporarily
after this your device will detect by your computer correctly.
Pressing buttons requires special timing and preconditions and a few more tries
To fully power off your phone, press Volume up and Power button for 10 seconds. Release immediately after the screen turns black.
Your phone is in the state of powered off even your screen displaying error message or charging animation, just make sure it's not in fastboot, recovery or booting animations.
Connect your phone to your computer before press Volume up and down and Power Button all at the same time to enter EDL mode.
Prepare yourself with Device Manager and MSM tool open and configured correctly before your phone enter EDL mode. There's a about 10 second window for you to start flashing.
Fail amid your MSM flash process:Don't panic if you see error message saying you didn't finish flashing
You can flash it anytime just make sure checking all the things above and enter EDL mode
Check these things：
Check your Windows can install the unsigned driver correctly
Check Device Manger in Control Panel if your device is correctly detected as a COM device as Qualcomm HS-USB QDLoader 9008 or something like this
Use administrator privilege to open the MSM software
Check your cable connection is stable or not.
Finally, thanks Dr.E (Max Lee) for your help. Without your video instructions, I won't revive my phone. It spares my pain to ask my dad for money for a new phone I don't actually need.
Hope everyone could find some helpful information in this post and flash your phone like a champ.
A even better way to enter EDL mode is power off and unplug your device, and after hold volume up and down at the same time, plug in the USB 2.0 cable to the computer. It works every time!!
i cant join rdl mode always restarting fastboot mode