I installed two different models of Joyings newest PX5-based head units. Both are the 7 inch screen 4GB RAM / 32GB flash double DIN model with flat buttons on the left edge.
Please note that as of May 2018, there appear to be multiple new 4GB / 32GB Joying head units have different internal hardware and are not compatible with each other or with the PX5 2GB Joying head units.
JY-UM128N4PX5 is a QD unit
JY-UO128P4 appears to be an FYT unit
Buyer beware. My recommendation is AVOID the QD based units and seek out the FYT units.
See below for more details.
The following information is for JY-UM128N4PX5. Further down the page is information for JY-UO128P4.
=============== JY-UM128N4PX5 =================
Came with Android 8.0.0 installed.
APP Version TP6735 0.0.65
MCU Version TP6735 4.40
Kernel Version 4.4.103
Master password:126
Password for changing logo:0000
Password for changing UI:8086
So far I have noticed the following:
The unit does not trigger the amplifier turn on signal wire - the orange and black wire labeled AMP-CONT always measures zero volts on my voltmeter. Workaround is to use either the antenna signal wire, or the ACC power signal wire, to turn on your amp. Joying is aware of this issue.
Sleep does not work. The unit shuts down completely about one minute after you turn off the vehicle's ignition. It doesn't sleep and then come back on instantly like my Intel-based Joying unit. Boot time is about 20 seconds. Joying support now says that sleep is not supported on the QD units.
I cannot find the radio settings in the new radio app. You used to be able to slide the bar at the bottom of the radio app to get to settings. Now in Android 8, there are a couple of radio settings that have been moved to the main android setup dialog.
Some of the functionality of the former car settings app has been moved to the android settings dialog. But not everything is there - for example this is where I was looking for the ability to tell the unit to toggle the amplifier signal wire. I could not find any such setting.
AM radio reception is non-existent - static on all AM channels.
FM reception is good, but I cannot figure out how to get the FM Radio to enable display of song and station information - this used to be under RDS settings, which no longer exist.
Bluetooth calling works fine. Seems more stable than my older Intel-based unit.
Sound quality is good - I am using an external amplifier.
The logo set up is missing Porsche and Saab Logos. My Intel-based Joying unit had these. Easy enough to load my own custom logo.
The unit ships with Joying's "Launcher3" selected. On the home screen, the labels of the bottom row of icons are cut off. The screenshots on Joying's website show the same thing. The joying2 launcher is missing.
If you reflash the unit, the vertical keypad on the left side of the unit gets un-mapped and stops working. Fix is to go into car settings and remap it.
========================= JY-UO128P4 ==================
Android Version 8.0.0
Build Number px5-userdebug 8.0.0 OPR5.170623.007
System Info APP 1024x600 2018-04-27 21:42:36
MCU Version 2018-01-23 10:59:33 JY_(R68)_R-86C-096I-NC-NP-1.0-P12S
Passwords:
Factory settings: 3368
Developer Options: 3368
Reset: 3368
Password for changing Launcher:8086
Password for changing screen current:
So far I have noticed the following:
The software on the JY-UO128P4 is very close to that of my older Joying Intel based system.
The developer has replaced all of the system settings screens native to android with their own settings screens. Not super cool. All of the car settings and android system setting are now intermingled.
Upon unboxing, the JY-UO128P4 has only a single Wifi antenna wheras the JY-UM128N4PX5 had two (diversity) wifi antennas. I have not tried to compare reception differences.
The amplifier turn on signal now works as expected (AMP-CONT wire correctly signals 12V when unit is active)
Sleep works as expected
AM radio reception works weakly.
The FM radio application works as expected. Radio app settings are accessed within the radio app. It's possible to enable RDS for song and station ID within the radio app.
All of the joying launchers are available - I prefer launcher 02 and it's available on this unit.
Many more car logos are available on the system. Porsche logo was built-in.
The only things I've noticed so far that are worse with the JY-UO128P4 than the JY-UM128N4PX5
The unit suffers from the android 8.0 bug on Joying where all of your google contacts are deleted if you allow your account on the head unit to sync contacts with google.
As noted above - the native android settings panels are all removed.
The app for setting the color of the buttons on the side panel is limited to pre-determined solid colors - yellow, white, red green etc. On the JY-UM128N4PX5 you could select and set any RGB color, which made it possible to match the button illumination to your other dashboard lights.
As I learn more, I will post more.
ddruker said:
I just installed Joying's newest PX5 head unit. It's the 4GB model.
It came with Android 8.0.0 installed.
APP Version TP6735 0.0.65
MCU Version TP6735 4.40
Kernel Version 4.4.103
So far I have noticed the following problems:
The unit does not trigger the amplifier turn on signal wire - the orange and black wire labeled AMP-CONT always measures zero volts on my voltmeter. Workaround is to use either the antenna signal wire, or the ACC power signal wire, to turn on your amp. I found another post of someone else who had this same issue.
I cannot find most of the passwords needed to set up the unit. The master password is 126 - I found that by watching a joying video. But I cannot find the second level passwords for changing the logo, changing the launcher, etc. Anyone have the other passwords?
The utility to change the color of the buttons on the left side of the unit works, but the buttons do not illuminate one the unit is booted.
I cannot find the radio settings in the new radio app. You used to be able to slide the bar at the bottom of the radio app to get to settings. Now in Android 8, there are a couple of radio settings that have been moved to the main android setup dialog - but for example I cannot find a setting to turn on the functionality to identify song and station names.
Some of the functionality of the former car settings app has been moved to the android settings dialog. But not everything is there - for example this is where I was looking for the ability to tell the unit to toggle the amplifier signal wire. I could not find any such setting.
I cannot figure out how to change the launcher - with the default launcher the lower row of app icons is only half visible on the screen.
Who else has a new Joying Android 8 unit - what else are you seeing? Has anyone found solutions to the items above?
Click to expand...
Click to collapse
I have had several back and forth emails with Joying support in the last couple of days.
They are trying to find the passwords for their new units under Android 8. Support didn't know. They had me try 00000 and 123456, neither of which worked. I told them the main password is 126 - they didn't know this either. I still need passwords for all of the second level settings - change the launcher, change the logo, see if there are more developer options for car config, etc.
They are apparently aware that the AMP-CONT lead to turn on the external amplifier does not work. They recommend connecting the accessory wire from your vehicle to the amp signaling wire instead, so the amp will turn on when you turn your key to the accessory or on position, bypassing the head unit.
They acknowledge there are no detailed settings available for the radio under Android 8 in the radio app. So there is no way to turn on station or channel ID for US customers.
I also let them know about another radio issue - FM Radio reception is normal, but AM reception is awful to non-existent.
Google maps is ok, directions from Google maps are mixing with other audio ok.
Feels like Android 8 on the new Joying 4GB units isn't quite ready for prime time yet... Has anyone tried to upgrade a 2GB Android 6 unit to Android 8 now that the Android 8 files are on Joying's website? Do you see the same behaviors, or am I seeing hardware issue with the brand new 4GB units? I suspect it's all software, but would be nice to know.
ddruker said:
Feels like Android 8 on the new Joying 4GB units isn't quite ready for prime time yet... Has anyone tried to upgrade a 2GB Android 6 unit to Android 8 now that the Android 8 files are on Joying's website? Do you see the same behaviors, or am I seeing hardware issue with the brand new 4GB units? I suspect it's all software, but would be nice to know.
Click to expand...
Click to collapse
The 2GB units are not compatible with the 4GB units. They need different hardware drivers and different MCU firmware as the firmware in the 2GB units is from FYT. I forgot the manufacturer of the 4 GB units but @gtxaspec knows.
There is no downloadable firmware yet for the 2GB units.
hi, i've the same unit and the password was noted into the user manual, it's 3368.
If you buy Joying android 8.0 unit the SKU like:JY-UO135N4PX5 or JY-UOS03N4PX5,password as below:
Master password:126
Password for changing logo:0000
Password for changing UI:8086
TomTom
It seams to be so hard. Again an Android HU, where TomTom navigation does not work. It let's me download the maps, but after that it crashes every time I try to load the application.
I can confirm these passwords are correct:
Master password:126
Password for changing logo:0000
Password for changing UI:8086
Other findings so far:
The illuminated buttons do work - they sometimes take a few seconds to come on after your illumination wire signals with 12V.
The logo selection with this new unit does not include Porsche or Saab. You can still upload your own custom logos.
I updated the unit to the latest (2018-4-20) release on the Joying website which is supposed to include optimizations and Zlink and my unit is now hanging at the Android text logo (right after the animated Android logo). I sent a note to Joying support for help and will also wait for a few hours to see if it comes back to life.
ddruker said:
I can confirm these passwords are correct:
I updated the unit to the latest (2018-4-20) release on the Joying website which is supposed to include optimizations and Zlink and my unit is now hanging at the Android text logo (right after the animated Android logo). I sent a note to Joying support for help and will also wait for a few hours to see if it comes back to life.
Click to expand...
Click to collapse
The same happened to me
After writing about 25 emails with Joying support I had to reflash the whole system ... loosing all my data.
For now I am really not going to try any more updates from Joying with this unit.
Really hoping for a Custom Rom & Root for this unit.
I have one of these as well. Any one find where the setting is to make the sleep mode last longer(2hrs) before it full shuts down? it seems to be locked on 30sec currently. Also it wont pair with my OBDlinkMX BT dongle. in the older MTCD units, making the BT password 1234 let you do it, but not here. anyone have any luck with BT OBD dongle pairing?
I was really leaning towards getting this unit but have been holding off because I wish it had Bluetooth 5.0, maybe I should wait a little longer since it seems to have a fair amount of bugs. I know a lot of people are happy with the Xtron since it has all the best features I just really prefer to have the buttons on the left like this unit has. Looking forward to seeing if you guys can get this squared away
peregrines said:
The same happened to me
After writing about 25 emails with Joying support I had to reflash the whole system ... loosing all my data.
For now I am really not going to try any more updates from Joying with this unit.
Really hoping for a Custom Rom & Root for this unit.
Click to expand...
Click to collapse
I was able to get my unit working again by reflashing. It took about 10 tries with three different USB cards but it finally worked. Joying support provided a file that included a system image and a Window-based chinese language USB card writing programs, along with a word document with instructions. You build the USB drive and then plug it into the left hand USB connector, and click the reset button on the front of the unit. It loads, then tells you to remove the USB drive, and then if you are very lucky it will reboot into Android.
After re-flashing, the vertical keyboard on the left side of the unit did not work. Turned out the mappings had been erased. Fix is to remap the keys - there is an option in car settings.
Current issues still present in the unit seem to be:
Unit shuts off entirely after 30-60 seconds instead of sleeping when you turn off the vehicle. My intel-based unit sleeps for several days.
No AM radio reception - static on all channels.
No way to turn on song or station identification in the radio settings for FM.
AMP-cont signal wire does not work. I've worked around by wiring my accessory wire directly to my amp's signaling wire.
Have not tried Torque and Bluetooth ODBII reader pairing yet - on my list for this weekend.
So, it's not just me...
I purchased a JY-UM135N2PX5 (PX5 2G/16G) with Android 6.0 mid to late March.
I had it on my bench through April, testing and configuring it prior to install.
After trading emails with Joying tech support, I was sent an Android 8.0 update to address a Zlink/iPhone issue.
I started my install in the car today, and discovered "no sound". I guessed that the AMP-CONT wasn't turning on the OEM amplifier. I rechecked the cables, which checked out just fine. Tried a Joying JY-UM135N2 (Intel Sofia 2G/32G Android 6) on the same harness, and it functioned as expected (turned the OEM amplifier on and had sound). I took them both back to my bench and noticed that the "AMP-CONT" on the PX5 unit did not appear to have 12V on it, while the Sofia unit did.
I did not leave the non-functional PX5 unit in the car long enough to see any other issues.
I am curious if I were to revert back to Android 6 on the PX5 unit, if it would fix the AMP-CONT issue (at the cost of breaking the Zlink/iPhone functionality)
ddruker said:
I was able to get my unit working again by reflashing. It took about 10 tries with three different USB cards but it finally worked. Joying support provided a file that included a system image and a Window-based chinese language USB card writing programs, along with a word document with instructions. You build the USB drive and then plug it into the left hand USB connector, and click the reset button on the front of the unit. It loads, then tells you to remove the USB drive, and then if you are very lucky it will reboot into Android.
After re-flashing, the vertical keyboard on the left side of the unit did not work. Turned out the mappings had been erased. Fix is to remap the keys - there is an option in car settings.
Current issues still present in the unit seem to be:
Unit shuts off entirely after 30-60 seconds instead of sleeping when you turn off the vehicle. My intel-based unit sleeps for several days.
Poor AM radio reception
No way to turn on song or station identification in the radio settings.
AMP-cont signal wire does not work. I've worked around by wiring my accessory wire directly to my amp's signaling wire.
Have not tried Torque and Bluetooth ODBII reader pairing yet - on my list for this weekend.
Click to expand...
Click to collapse
Would you be so kind as to share those files with us? This would be a good starting point for further testing and research. Simply upload to a hoster like mega.
z0rn said:
Would you be so kind as to share those files with us? This would be a good starting point for further testing and research. Simply upload to a hoster like mega.
Click to expand...
Click to collapse
Here is a link to the zip file from Joying with the firmware image for reflashing, their USB drive utility, and instructions...
https://drive.google.com/open?id=13HXHRRfuduhIYV41pjQlvsJ0o3xesNBC
Here is the reply I got from Joying support this morning in regards to the open defects I am tracking with the unit. I suspect that all of this will get fixed in subsequent software releases, it's relatively obvious stuff. Can anyone confirm if these same issues exist in the Android 8 builds on Joying's 2GB PX5 head units, or are these unique to the newest 4GB units?
Dear friend,
Please noted :
1) sorry that your system is different with Intel head unit , it do not have fast boot feature . so it will completely off .
2) for the AM receptions is bad , you need to set the proper time and zone . also the radio area choice .
3) sorry, the head unit you purchased do not have the RDS setting .
4) for the am-cont not voltage , please connect the ACC (red wire ) to your amplifier wire . then can offer 12V .
Hope your noted .
Candy
ddruker said:
Here is the reply I got from Joying support this morning in regards to the open defects I am tracking with the unit. I suspect that all of this will get fixed in subsequent software releases, it's relatively obvious stuff. Can anyone confirm if these same issues exist in the Android 8 builds on Joying's 2GB PX5 head units, or are these unique to the newest 4GB units?
Dear friend,
Please noted :
1) sorry that your system is different with Intel head unit , it do not have fast boot feature . so it will completely off .
2) for the AM receptions is bad , you need to set the proper time and zone . also the radio area choice .
3) sorry, the head unit you purchased do not have the RDS setting .
4) for the am-cont not voltage , please connect the ACC (red wire ) to your amplifier wire . then can offer 12V .
Hope your noted .
Candy
Click to expand...
Click to collapse
Are they serious? I would suggest to try the Malaysk Rom, i guess your units are MTCD and MTCE devices so maybe this rom would support the missing software like rds and the other hardware not supported by Joying
https://www.youtube.com/watch?v=WWvgrcn_As8
https://forum.xda-developers.com/an...-malaysk-roms-px5-2-4-gb-8-0-android-t3762724
Good luck!
Flemischguy said:
Are they serious? I would suggest to try the Malaysk Rom, i guess your units are MTCD and MTCE devices so maybe this rom would support the missing software like rds and the other hardware not supported by Joying
Click to expand...
Click to collapse
These units are NOT MTCD/E. Do not use the Malaysk ROM.
---------- Post added at 07:08 PM ---------- Previous post was at 06:53 PM ----------
ddruker said:
Here is the reply I got from Joying support this morning in regards to the open defects I am tracking with the unit. I suspect that all of this will get fixed in subsequent software releases, it's relatively obvious stuff. Can anyone confirm if these same issues exist in the Android 8 builds on Joying's 2GB PX5 head units, or are these unique to the newest 4GB units?
Dear friend,
Please noted :
1) sorry that your system is different with Intel head unit , it do not have fast boot feature . so it will completely off .
2) for the AM receptions is bad , you need to set the proper time and zone . also the radio area choice .
3) sorry, the head unit you purchased do not have the RDS setting .
4) for the am-cont not voltage , please connect the ACC (red wire ) to your amplifier wire . then can offer 12V .
Hope your noted .
Candy
Click to expand...
Click to collapse
I have a 2GB Android version 8.0.0 unit, but my unit is a FYT based unit like the Sofia 3GRs, unlike yours which is a QD unit.
Mine does have fast-boot as my unit is a FYT based unit, using the same hardware/SOM as the Sogia 3GR intel units.
I never used AM-reception. I wouldn't know, but I know from previous users on Sofia 3GR that they also complained about the AM reception
Which RDS-setting? This is so confusing and so not concrete. RDS is a complete set of functions. The syu/FYT based software on the FYT based units support RDS-PS, RDS-PTY and RDS-TA/TP. The latest firmware versions on FYT units (Sofia 3GR and my PX5) also support RDS-RT. They do not support RDS-AF. They implemented "something" like AF. If you use that option it does not select the Alternate Frequency of your radio station, it selects the strongest signal it can find of any station. Note that it is the software. The radio chips in all these units support the complete RDS set of functions.
Don't know about the the amp-cont wire.
You ask about and mention AM and about RDS. I hope you know that RDS can only be used on the FM signal. RDS is not available for AM.
Help
Heres a link I need help to identify my android head unit
https://app.box.com/s/o90d0lnjrqqlek5w1q6lekaj5dgsa20y
Traww said:
Heres a link I need help to identify my android head unit
https://app.box.com/s/o90d0lnjrqqlek5w1q6lekaj5dgsa20y
Click to expand...
Click to collapse
You have an Allwinner T3 chipset in your unit.
Do not use a Joying thread to ask a completely off-topic question.
I've received the same unit, facing the same issues as the OP.
Also the localisation in my language is quite poor.
surfer63 said:
These units are NOT MTCD/E. Do not use the Malaysk ROM.
Click to expand...
Click to collapse
I've bought this unit in the hope that it would be compatible with custom ROMs.
Are you saying that the unit MCU is almost unknown and that no custom ROM would be available in the near future?
Processor type- UltraOcta-T8
Android version- 7.1.2
MCU- 5.3.19-94-84-E06101-180111
System ver- v9.2.2_20180314.153952_TW2-FD
I have the Xtrons tr100 which has been a very great upgrade from the last unit I had, especially the sound quality. The only problem I'm having is an issue with the bluetooth which will not connect to my obd2. When i search for bluetooth devices the obd2 does show up, when I press and hold on obd2 3 options pop up which are ok, obd2, and cancel. I tried all options with no success. I went into the extra settings and chose bc6 and/or bc8 with no luck. Anything elee I'm missing or could try?
Hi, Your unit appears to be an allwinner unit and so posting in the android auto forums you might not get a response. Here's a starter for you:
https://forum.xda-developers.com/sitesearch.php?q=5.3.19
Thanks a lot
marchnz said:
Hi, Your unit appears to be an allwinner unit and so posting in the android auto forums you might not get a response. Here's a starter for you:
https://forum.xda-developers.com/sitesearch.php?q=5.3.19
Click to expand...
Click to collapse
Hi Marchnz,
you said above that "trigga_b Your unit appears to be an allwinner unit and so posting in the android auto forums you might not get a response." would be better on a different thread why is that?
I have the same head unit TR100 and after searching for Xtrons TR100 I ended up here do you not consider this an android head unit it is running Android 7.1 nougat
Regards Poppy Ann.
Hello,
After installing my android head unit ( Navifly 7862 android 10 4gb/64gb ), when I drive, my speedometer remains at 0.
it seems that there is no option in the menu to activate it.
Maybe it's a wiring problem.
otherwise everything else works fine
Gnewstyl said:
Hello,
After installing my android head unit ( Navifly 7862 android 10 4gb/64gb ), when I drive, my speedometer remains at 0.
it seems that there is no option in the menu to activate it.
Maybe it's a wiring problem.
otherwise everything else works fine
Click to expand...
Click to collapse
[ RESOLVE]
after some research and wiring checks. One of the wires from the universal connector was poorly wired.
The blue wire was connected to the wrong input.
is this navifly device good build quality?
Can you give a review about it.
I'm interested because it seems to have good radio chip (TEF6686), good cpu, functionality, etc but...
Since I have a Bosion with px6 cpu, fake android 10 and a few problems with sound quality, radio quality, steering wheel buttons, I'm disapointed with it.
Thank you
Hi All,
I'm bit new to the world of Android Head Unit who recently purchased a PX5 Android 10 head unit for my Peugeot 407.
After installation everything works fine expect for one problem. WiFi doesn't work.
If I turn ON the WiFi, it finds my network, connects to it, and then immediately the WiFi turns OFF. It keeps turning ON and OFF in loop.
So reached out to my seller who provided a firmware file using which I upgraded my unit successfully. But no luck. WiFi still has the same problem. It keeps turning ON and OFF in continuous loop.
Head Unit Specifications
Car: Peugeot 407
Unit: PX5
CPU: Octa-core Cortex-A53 @1.5G
Memory: 4GB
Storage: 64GB
MCU Version: MTCE_MX2_V3.60_1
Kernel Version: 4.19.111+
Build Number: rk368-userdebug 10 [email protected] eng.hct2.20200909.085823
Bluetooth Module: WQ_RF210 (as pre-selected in the Factory settings in the head unit)
I've attached a video of my symptoms as well. Please can you have a look and advise / point me in the right direction to fix this WiFi problem.
I spent time tracking down the seller for firmware update because I'm not sure how to identify the specific model / manufacturer etc of the unit.
Any advise on how to identify the finer details associated with the Head Unit Model would also be very helpful.
Thank you.
livewyr said:
Hi All,
I'm bit new to the world of Android Head Unit who recently purchased a PX5 Android 10 head unit for my Peugeot 407.
After installation everything works fine expect for one problem. WiFi doesn't work.
If I turn ON the WiFi, it finds my network, connects to it, and then immediately the WiFi turns OFF. It keeps turning ON and OFF in loop.
So reached out to my seller who provided a firmware file using which I upgraded my unit successfully. But no luck. WiFi still has the same problem. It keeps turning ON and OFF in continuous loop.
Head Unit Specifications
Car: Peugeot 407
Unit: PX5
CPU: Octa-core Cortex-A53 @1.5G
Memory: 4GB
Storage: 64GB
MCU Version: MTCE_MX2_V3.60_1
Kernel Version: 4.19.111+
Build Number: rk368-userdebug 10 [email protected] eng.hct2.20200909.085823
Bluetooth Module: WQ_RF210 (as pre-selected in the Factory settings in the head unit)
I've attached a video of my symptoms as well. Please can you have a look and advise / point me in the right direction to fix this WiFi problem.
I spent time tracking down the seller for firmware update because I'm not sure how to identify the specific model / manufacturer etc of the unit.
Any advise on how to identify the finer details associated with the Head Unit Model would also be very helpful.
Thank you.
Click to expand...
Click to collapse
Did you check the wifi antenna?
I have a 407 - (2007) - does your head unit allow for aircon and heating/ventilation controls and all the canbus functions?
my orange dispaly is failing so thought I'd install one of these instead
Do you have a link for the one you bought? I've been looking for octacore - most are quad
Thanks
Found some interesting info here
[SOLVED] I can’t turn ON my Wi-Fi... Need help
I have update my mtce px3 Android 7.1 MTCE with a px5 Android 6 and charged malaysk rom based on Android 8.0... but afther that i can’t turn ON my Wi-Fi. Bluetooth working perfect... all the thing working good.. only Wi-Fi don’t wont to turn on...
forum.xda-developers.com
maybe unplug any usb's you have, and/or request a firmware update from vendor
snailer said:
Did you check the wifi antenna?
I have a 407 - (2007) - does your head unit allow for aircon and heating/ventilation controls and all the canbus functions?
my orange dispaly is failing so thought I'd install one of these instead
Do you have a link for the one you bought? I've been looking for octacore - most are quad
Thanks
Found some interesting info here
[SOLVED] I can’t turn ON my Wi-Fi... Need help
I have update my mtce px3 Android 7.1 MTCE with a px5 Android 6 and charged malaysk rom based on Android 8.0... but afther that i can’t turn ON my Wi-Fi. Bluetooth working perfect... all the thing working good.. only Wi-Fi don’t wont to turn on...
forum.xda-developers.com
maybe unplug any usb's you have, and/or request a firmware update from vendor
Click to expand...
Click to collapse
I can't find my exact seller listing but below link is a similar eBay listing for the same model I have got.
Peugeot 407 Android 10 PX5 4-64
Yes, it integrates seamlessly with canbus / climate control etc. It comes with a canbus connector. There's an option to connect reverse camera if you want to. But you have to buy the reverse camera separately. Other than that there's a GPS antenna, built in and extra microphones for phone calls, memory card slot, USB slots etc.
I wouldn't recommend any sellers for this kind of after market head units as they are all sold / shipped by overseas / international sellers. There's always a risk with this type purchases. So proceed with caution. If you end up getting a good unit, the risk is well rewarded. Your Pegueot gets a major upgrade.
All the best!
Thanks!
I've been looking at these ones.
Still undecided
Might just get a new mfd screen & keep using my phone!
plamenangelov said:
I have a problem with my auto daylight, my old navigation system was Rneg and all work fine. When start engine auto daylight in on but when install new Witson auto daylight stop work, i must start it manuali on setting via Witson unit. I have menu auto daylight runigh light when touch it, light is on but button still unactive.
Click to expand...
Click to collapse
Maverickky said:
I have the same problem, any solution?
Click to expand...
Click to collapse
livewyr said:
Hi All,
I'm bit new to the world of Android Head Unit who recently purchased a PX5 Android 10 head unit for my Peugeot 407.
After installation everything works fine expect for one problem. WiFi doesn't work.
If I turn ON the WiFi, it finds my network, connects to it, and then immediately the WiFi turns OFF. It keeps turning ON and OFF in loop.
So reached out to my seller who provided a firmware file using which I upgraded my unit successfully. But no luck. WiFi still has the same problem. It keeps turning ON and OFF in continuous loop.
Head Unit Specifications
Car: Peugeot 407
Unit: PX5
CPU: Octa-core Cortex-A53 @1.5G
Memory: 4GB
Storage: 64GB
MCU Version: MTCE_MX2_V3.60_1
Kernel Version: 4.19.111+
Build Number: rk368-userdebug 10 [email protected] eng.hct2.20200909.085823
Bluetooth Module: WQ_RF210 (as pre-selected in the Factory settings in the head unit)
I've attached a video of my symptoms as well. Please can you have a look and advise / point me in the right direction to fix this WiFi problem.
I spent time tracking down the seller for firmware update because I'm not sure how to identify the specific model / manufacturer etc of the unit.
Any advise on how to identify the finer details associated with the Head Unit Model would also be very helpful.
Thank you.
Click to expand...
Click to collapse
Have you guys found any solutions to your canbus problems with Peugeot 407? I lost my automatic headlights / daylights which I'd love to have back. Have you encountered and solved other issues with Android head units?
I can't either enable some car functions from car app from head unit (automatic lights, rear wiper, parking radar etc.). Can you see the outside / inside temperatures of the car somewhere? My A/C works somehow (responses like it should to physical buttons, but I bet it has mechanical faults instead communication problems with head unit).
gratnak said:
Have you guys found any solutions to your canbus problems with Peugeot 407? I lost my automatic headlights / daylights which I'd love to have back. Have you encountered and solved other issues with Android head units?
I can't either enable some car functions from car app from head unit (automatic lights, rear wiper, parking radar etc.). Can you see the outside / inside temperatures of the car somewhere? My A/C works somehow (responses like it should to physical buttons, but I bet it has mechanical faults instead communication problems with head unit).
Click to expand...
Click to collapse
What did the reseller suggest when contacted for support.
livewyr said:
Hi All,
I'm bit new to the world of Android Head Unit who recently purchased a PX5 Android 10 head unit for my Peugeot 407.
After installation everything works fine expect for one problem. WiFi doesn't work.
If I turn ON the WiFi, it finds my network, connects to it, and then immediately the WiFi turns OFF. It keeps turning ON and OFF in loop.
So reached out to my seller who provided a firmware file using which I upgraded my unit successfully. But no luck. WiFi still has the same problem. It keeps turning ON and OFF in continuous loop.
Head Unit Specifications
Car: Peugeot 407
Unit: PX5
CPU: Octa-core Cortex-A53 @1.5G
Memory: 4GB
Storage: 64GB
MCU Version: MTCE_MX2_V3.60_1
Kernel Version: 4.19.111+
Build Number: rk368-userdebug 10 [email protected] eng.hct2.20200909.085823
Bluetooth Module: WQ_RF210 (as pre-selected in the Factory settings in the head unit)
I've attached a video of my symptoms as well. Please can you have a look and advise / point me in the right direction to fix this WiFi problem.
I spent time tracking down the seller for firmware update because I'm not sure how to identify the specific model / manufacturer etc of the unit.
Any advise on how to identify the finer details associated with the Head Unit Model would also be very helpful.
Thank you.
Click to expand...
Click to collapse
Hello there,
See this workaround.
Custom ROMs such as @Hal9k_ 's Mod V5 have workarounds for this under Mod settings. In that ROM, go to Mod settings, select "Hardware settings" and toggle on the "Reset USB devices when booting or waking up".