I am unable to factory reset sony android TV KDLW800C.
TV doesn't turn on. I tried hard reset with power key and vol -
I am able to see led green light momentarily but nothing is visible.
Can anyone help?
Related
I just got my Orange SPV M5000 (Universal)... but there arent any icons or shortcuts for me to soft reset the phone.
Even when i press the power button, it just turns the screen off and back on. Even when i hold the power button for long, it still doesnt soft reset.
Can someone help?
Have you tried poking the soft reset button, just next to the USB port on the back?
Or try VJEschaton.
V
thanks, i thought the reset hole in the back next to the usb deletes all my personal data, didnt know it was soft reset. Thank VJ
???????? :evil:
push "standbye" and "cam" button and than the reset
to show the colordisplay
and than put the usb in and flash another ROM
Click to expand...
Click to collapse
don't work (((
Well, this has happend to me a couple of times too, just hard reset.
Push Camera + Comm manager button together, then soft reset, but keep holding the camera and comm button.
When you get a message, click the green phone.
yeah, not sure what you're yelling, but i think your phone resets and only goes to a white screen and sits there?
happned to me and i almost cried. tried hard resets and nothing. left battery out for a day and nothing. i left it out again for a few hours cause i was pissed, put it in at 4am, did another hard reset and it started to work like normal, though resetted. keep trying!
I'd try all the stuff mentioned and make sure it is plugged in to the power supply.
hard reset and bootloader
for hard reset after you press both cam and comm button press soft reset the trick is dont release bot cam and comm bottons untill it prompts. finally press green button.
for boot loader device must be connected to crable or power. and press cam and power button then press soft reset. still the sam don release power and cam button until you see the color screen.
hi, after instaling pretty much of applications on my wizard it just stopped respond. if u do a soft reset it boots but freezest on todays screen and thats it. there is a massage dispalied "low memory". i cannot do a hard reset, upgrade rom anything. is there any other way to perform a hard reset ?? (i tried comm mnr+voice+plus soft reste) HELP !!!
cheers, matt
Some people have joy with - turn off - press and hold comm, record and camera buttons and press power on.
If that fails you should be able to flash your device with the same rom. Turn off, press camera button and hold then press power button and bootloader multicolored screen should come up. Connect via usb to pc and reflash rom.
I don't know what's happening but whenever I do a soft reset or turn the device on, the boot time takes longer and after showing the orange Window splash screen, a black screen appears with the text that says:
The device in unable to boot because either you have turned off the device incorrectly or tried to install an application from untrusted source.
Press Volume Up to do a hard reset...
True enough when the black screen appears and when I press the volume up, the device starts to hard reset. But despite the hard reset, the problem persists.
If I just let the black screen stand by, around a minute or so, it disappears and the device boots up and does so successfully.
Anybody has had this experience or might know what's going on? Any help/inputs are truly appreciated.
After i performed a Hard Reset for this device, the sreen came out with a weak lighting and no longer logged into windows
When plugging the USB cable with the PC, the signal light was still in red, looked like it was being connected with my PC.
Anyone can show me how to set this device into bootloader mode or perform a hard-buttons Hard Reset?
Highly appreciated for your reading and reply!
Regards,
Dong from Vietnam.
Please give me an advise!
to enter Bootloader mode:
Hold the two buttons next to Send and End + Power, and then press the reset button with stylus
to hard reset:
Hold Send + End + Power and press reset button with stylus should produce a message saying something like all clear.