Database Users

AL-C0241 or AL-5701

Created this thread so we can center all the info here
Wiki link
http://forum.xda-developers.com/wiki/AL-C0241
Click to expand...
Click to collapse

Guys I have a AL-C0241 and I just installed Malaysk's firmware.
I stupidly did not check my MCU type before hand, thinking that I would keep the existing MCU if I only updated the image.
Everything seemed to install fine, but when I look in the about tablet section, the first few lines are blank, including the MCU
And now I am getting no sound from the radio. Everything else including the wifi and GPS seems to be working OK, but no sound is a problem.
Can anyone tell me the original MCU code of the AL-C0241 ? This is the autopumpkin 7 inch with no buttons on it, just a flat screen.

you can see my entries on the wiki, it's there
http://forum.xda-developers.com/wiki/AL-C0241
this is the pic you are looking for.
https://www.dropbox.com/s/esnbvqtk2mqqvm3/IMG_20151006_212100.jpg?dl=0

nleitao said:
you can see my entries on the wiki, it's there
http://forum.xda-developers.com/wiki/AL-C0241
this is the pic you are looking for.
https://www.dropbox.com/s/esnbvqtk2mqqvm3/IMG_20151006_212100.jpg?dl=0
Click to expand...
Click to collapse
So I think mine is bricked now.
After loading Malaysk 3188/1024 firmware I no longer have:
*sound
*gps
*radio
Still working
*wifi
Any idea what I should do to try and fix it? I tried a few things with the reset button but was unable to achieve factory reset. Should I start trying some of the available MCUs?

Ask Pumpkin to send you an image file of your MCU and Firmware. I just send them an email requesting the same for my unit. I told them that I wanted to back it up and can't unless I am rooted.
Let's see what happens.
Georgetech

Georgetech said:
Ask Pumpkin to send you an image file of your MCU and Firmware. I just send them an email requesting the same for my unit. I told them that I wanted to back it up and can't unless I am rooted.
Let's see what happens.
Georgetech
Click to expand...
Click to collapse
Worth a try, I will do that.
Would it be possible to get an image of the stock SD card and use that to revert to factory? perhaps nleitao can take a copy of his if he still has access to the insides of his unit?
I'm pretty annoyed with myself, hopefully I don't have to buy another!

darkhorsefkn said:
Worth a try, I will do that.
Would it be possible to get an image of the stock SD card and use that to revert to factory? perhaps nleitao can take a copy of his if he still has access to the insides of his unit?
I'm pretty annoyed with myself, hopefully I don't have to buy another!
Click to expand...
Click to collapse
I have been exchanging some emails with them, because I was going to do what you did, but only after having the factory image... This is what I got:
Email said:
Hello Nuno,
Thanks for your email.
We attached the user manual for the AL-C0241,please check
And about the newer firmware and mcu, once we get it, we would release it on our official support www.news.autopumpkin.com
Thanks for your patience.
Have a nice day.
Kind regards,
Colin
2015-10-09 19:13 GMT+08:00 xxx:
Hello Sam, good morning
any news about the manual? also is there a place were I can get the Firmware and MCU files for an upgrade?
thanks
Nuno
Click to expand...
Click to collapse
Today I'll reply asking the most recent they have.
I would gladly do image backups if someone explains me how to do it without root...
thanks
Nuno

darkhorsefkn said:
Any idea what I should do to try and fix it? I tried a few things with the reset button but was unable to achieve factory reset.
Click to expand...
Click to collapse
Factory reset would be Malaysk's reset...

Firmware Pupkin C-0241
h....ttp....s://yadi.sk/d/bc0l7ZzAjhZU2

Andron66 said:
Firmware Pupkin C-0241
h....ttp....s://yadi.sk/d/bc0l7ZzAjhZU2
Click to expand...
Click to collapse
Thank you so much! downloading now, will post results!
---------- Post added at 12:21 PM ---------- Previous post was at 12:08 PM ----------
Just found a couple of youtube videos, from the official pumpkin channel "pumpkin car stereo support" where they show a software and MCU update for the AL-C0241 !
No download link however! Search AL-C0241 on you tube if interested.
Also checked their blog, no update there
edit: Can't test their firmware because my USBs no longer work, along with most of my hardware.
Its not looking good for me :| Maybe I can find a way to get them working on Malaysk's rom but it's a bit of a catch 22. I can get internet access on the device, however, so all hope is not lost.

darkhorsefkn said:
Can't test their firmware because my USBs no longer work, along with most of my hardware.
Click to expand...
Click to collapse
have you tried the internal SD slot?

youtube.com/watch?v=cRlAs7ijSOk

nleitao said:
have you tried the internal SD slot?
Click to expand...
Click to collapse
Any luck?
Try the Internal SD card, here you have a picture of my radio
SD Card

nleitao said:
Any luck?
Try the Internal SD card, here you have a picture of my radio
...
Click to expand...
Click to collapse
I opened my device and that slot is empty. I thought that was for a sim card to enable 3g?
I will put the update.img file on a new sd card and try it tonight, I will post results in approximately 8 hours time
Thanks for the help

darkhorsefkn said:
I opened my device and that slot is empty. I thought that was for a sim card to enable 3g?
I will put the update.img file on a new sd card and try it tonight, I will post results in approximately 8 hours time
Thanks for the help
Click to expand...
Click to collapse
Nop, it's an SD card slot

Sorry guys I have no results as yet, got a bit busy last night
I have to rig up a molex connector so I can power the device up while im inside my house, it should be as simple as connecting the yellow 12v rail and the earth to the harness, so hopefully I will be able to inform you of results before long
Thanks for the support

Fixed!
Thanks for all the help
I used the ROM posted earlier in this thread and the internal SDslot and I eventually got everything working again, I much preferred Malaysk's ROM but couldn't manage to get the MCU updated until after I did the ROM update.
I now have alex v1.1.5 however, I used to have v1.1.7, so that's kinda annoying but I can't see the difference right now anyway. I will write to auto pumpkin and try to get the latest image.
I was also not able to get it to power up using my computer power supply. I connected the 12v to the 12v and the earth to the earth but it wouldn't fire up, super annoying.
Now I am just going to enjoy using it for a while
build == http://imgur.com/eRW2Asy

darkhorsefkn said:
I was also not able to get it to power up using my computer power supply. I connected the 12v to the 12v and the earth to the earth but it wouldn't fire up, super annoying.
Click to expand...
Click to collapse
I'm really glad you fixed it up!
You should had connect the red and the yellow to the 12v...
My apologies to the OP for the kind of hijack but I believe this is the thread with most info for this radio.
I'm having problems with my radio. The screen seems to have a bad contact somewhere, making it complete useless to try to work with it. The odd thing is it never happens in the first 20 minutes ater a cold start. Does someone have an idea what is happening here?
https://www.youtube.com/watch?v=VMCrWkFdd0I
Second problem. I'm completely unable to pair the radio's Bluetooth with whatever devices. I just cant start the pairing process from the radio side.
https://www.youtube.com/watch?v=60cV8FlRpw4
thanks in advance
Nuno

nleitao said:
I'm really glad you fixed it up!
You should had connect the red and the yellow to the 12v...
My apologies to the OP for the kind of hijack but I believe this is the thread with most info for this radio.
I'm having problems with my radio. The screen seems to have a bad contact somewhere, making it complete useless to try to work with it. The odd thing is it never happens in the first 20 minutes ater a cold start. Does someone have an idea what is happening here?
https://www.youtube.com/watch?v=VMCrWkFdd0I
Second problem. I'm completely unable to pair the radio's Bluetooth with whatever devices. I just cant start the pairing process from the radio side.
https://www.youtube.com/watch?v=60cV8FlRpw4
thanks in advance
Nuno
Click to expand...
Click to collapse
That screen flicker doesn't look good Is your warranty void due to opening the device? Could be a hardware fault.
As for the bluetooth pairing, I think mine just worked the first time and I haven't looked at it since. I will have another look later and see if mine is doing the same thing

darkhorsefkn said:
That screen flicker doesn't look good Is your warranty void due to opening the device? Could be a hardware fault.
As for the bluetooth pairing, I think mine just worked the first time and I haven't looked at it since. I will have another look later and see if mine is doing the same thing
Click to expand...
Click to collapse
Today I received this answer from them
Support Email said:
Thanks for your feedback.
We're so sorry for the inconvenience and trouble.
1) Firstly sorry for my wrong info about the instruction before,for this new Android product, currently it has no searching function in the built-in Bluetooth. About dropping the built-in Bluetooth app to pair the Bluetooth OBDII with other Bluetooth app, sorry we did not test it before and not sure the operation. However, this product can directly pair the the Wifi OBDII which is tested by us
2) Regarding this issue, frankly we didn't meet it before, if you're good at electronic, it's ok to open the radio by removing screws around the frame then check out the inside connection and we would still promise the warranty.
If we can be of any assistance,please feel free to tell us,thank you!
Best regards,
Colin
Click to expand...
Click to collapse
So two things I learned. The crappy Bluetooth App can't connect to other devices. The second is I still have warranty after open the cover and check the internal cables.
Yeah, I suspect hardware fault. It only start happening after 20, 25 minutes after power up. something heats up and puff...

Bricked Atoto A6, Need some help.

Have not done much with rooting android devices in years and recently bought an Atoto A6 for a work van. I started messing around with it at home. Was able to gain root with Kingoroot and the replacing it with SuperSU. I emailed them about unlocking the bootloader but I'm not sure whoever responded even knew what I was talking about. Although ADB was working with system booted, I was not able to connect to the unit in fastboot. If you boot into recovery, it automatically runs an update and reboots. And if you boot into Fastboot with acc powered, fastboot automatically restarts. So using adb to reboot into bootloader and then removing power from acc would get me to a fastboot screen(although screen is off, putting power back to acc would show screen at fastboot mode) but I was never able to connect. I was trying different things to boot into an actual recovery, the A6 has no physical buttons, just a small hole for the reset. At some point it completely stopped responding. None of the sensor buttons light up and nothing on the screen. The micro sd I had in no longer works either. I did have update.zip backed up. Anyone know if there would be a way to use that to boot from a new micro sd or any other ideas to try, any help is appreciated.
The a6 has a mediatek mt8127. Was coming up as Alps A6. The build was alps/full_A6_series/A6_series:6.0/MRA58K/1506516231:user/test-keys . I did have it apart and have pics of the board, don't know if they would be useful though.

Upon further review, board mounted reset button was screwed up, all good now. Would be nice to figure out the bootloader on this, although I don't have it installed in a vehicle, this unit seems to run pretty well. Not a fan of the the launcher setup and appearance .

stabone00 said:
Upon further review, board mounted reset button was screwed up, all good now. Would be nice to figure out the bootloader on this, although I don't have it installed in a vehicle, this unit seems to run pretty well. Not a fan of the the launcher setup and appearance .
Click to expand...
Click to collapse
Glad you "unbricked" it, and glad somebody is willing to risk rooting it. That might go on my weekend project list, would appreciate more details on Kingroot and how you swapped it with SSU. I miss ad blockers, among other things.
I got the same unit from Amazon last week (2gb touch only version), but wish I had opted for the physical button model now.
My biggest complaint is the damned FM radio app, which by default comes on when it comes out of sleep, and there's no obvious way to disable it. The volume level on FM is like 2x streaming/MP3 volume so it blasts you when starting the car if you forget to turn volume way down when you get out. I'd love to know the actual app name so I could disable it entirely, since I never listen to broadcast radio anyway.
Oh, and the parallax on the thing is annoying, getting a finger lined up on small touch targets takes some practice.
Other than that issue, I'm not unhappy with the unit. 2-second boot is legit, and living in Florida and an open sunroof junkie, I'm especially pleased with the screen brightness.
Using CarWebGuru instead of the default Atoto launcher makes for a much better experience, and I like the fact that the Atoto controls on the bottom (home, back, multi-tasking, brightness, mute) all remain there no matter what launcher you choose.
Sound quality using my car's factory amp (via a Metra CANBUS harness) is surprisingly good too, I can't tell much difference between the A6 and the Pioneer FH-X730 it replaced at the volume levels I like, though there is some RF bleed from the SoC. And it's a near-perfect fit in a Schoshe double-din GM dash kit, there's not enough room for a toothpick around the edges of the screen and the dash kit inner bezel.

For rooting use KingOroot. You need the one for windows, the app on the unit itself won't do it. Then just google replacing kingoroot with Supersu, there are lots of threads about it. You could try the simple version but I ended up manually replacing files to do it, it's not bad at all. I wouldn't be to worried about bricking it, I have been trying all different things to get to a bootloader and at worst it re-updated and was working fine. What i did with the reset button, Ive done to othere devices, those surface mount buttons are junk. After doing a ridiculous amount of research, I found that MTK units don't enable fastboot. The preloader is what you have to get into to do anything, using mtk drivers. I could catch it right when its booting, installs the mtk vcomm drivers, but jumps right out. Once you are in that you need their flash tool, SDflash and there is MTKtools. So once thats figured out, i'm hoping to be able to get a custom recovery on. Without fastboot, it seems a bit more tricky, without that reset button I could be missing something simple. Hopefully more people start screwing with these, I doubt the people at Atoto are going to be of much help. So far tho, it seems like a decent unit. Let us know if you find out anything.

So far I was able to extract the boot and recovery img files. You can connect to the preloader using SP Flash by setting it up to read

Ima let you do the heavy lifting on this one Stabone.
For now, I'm just frustrated on the damn FM app opening at startup and it's nested in the Atoto firmware somewhere, not an isolated app.
One other quirk, on my car (with GM 11bit CANBUS), the illumination signal seems to be flipped from what Atoto is expecting...lights on means brighter screen, lights off means dim. I've tried it with both an Axxess and PAC CANBUS adaptor, so it's not the harness' fault. Just using the NONE setting for now and manually dimming the screen myself.

I sure hope stabone00 keeps working on this. I have been following this thread closely. I have been wanting to root this but I have it installed in the car now. why cant this be easy like a nexus 7. I am very afraid of bricking it and I really like the head unit

Not sure what happened to my last post, it should've been a bit longer then that, hah, oh well. Anyway I'm a little stuck here. After finding out as much as I did, I was going to try a few things. I'm running a dual boot laptop with opensuse as my main and a windows 10, for occasions as such, the tools used for this head unit are more abundant for windows(at least found easier). So recently I wiped my systems and now am having this Rsa Key Fingerprint issue when trying to connect with adb. I'm spending way to0 much time on this as it is, lol. But running into this bs is really pain. Now I've tried for hours to do something here but it's almost as someone's watching what i'm doing and countering my moves. Now I've factory reset this thing about four times and never lost root. After struggling with this rsa fingerprint issue, I did a factory reset and now SuperSu is gone, although I can't say for sure totally cause I still have not access to ADB. Any suggestions for the rsa issue, let me know, otherwise I'm not going to be wasting much more time with this. BTW, anyone getting anywhere with this, you need the modified version of MTK android tools to recognize this unit. I have boot and recovery img's and a scatter file if needed.

Got passed issue with adbkeys. Now I accidentally flashed a recovery when it was not ready. I am now stuck in a boot loop. Made lots of backups, but for some reason, none contain the preloader.bin. Not sure why that happened, but that is needed to flash backups with SP tools. If anyone could send me that, it would be great. I can't pull it cause I can't get it to connect to mtk droid tools. Maybe there is another way, but I don't know it.

stabone00 said:
Got passed issue with adbkeys. Now I accidentally flashed a recovery when it was not ready. I am now stuck in a boot loop. Made lots of backups, but for some reason, none contain the preloader.bin. Not sure why that happened, but that is needed to flash backups with SP tools. If anyone could send me that, it would be great. I can't pull it cause I can't get it to connect to mtk droid tools. Maybe there is another way, but I don't know it.
Click to expand...
Click to collapse
I have the same unit. If you can tell me how to pull it, I'd be happy to help.

smithkt said:
I have the same unit. If you can tell me how to pull it, I'd be happy to help.
Click to expand...
Click to collapse
Have you tried anything with it yet? There's quite a bit to it. The info is all searchable on here, you are looking for mediatek devices, sp flash tool, mtk droid tools. Let me know if you have adb and drivers installed. All the info needed for this unit is available , but there is a lot of info on mediatek devices, so it's a lot to look at. You need to have developers options enabled and oem unlocked and usb debugging on . If you can connect to your unit through adb, thats a start. Don't attempt anything with fastboot, it's not enabled on this unit. You'll then want to look for the modified version of mtk droid tools 2.5.3. If you are able to connect with that, I'll tell you what to do next. Not so sure my unit is recoverable, i've lost the startup atoto screen and can no longer connect with sp flasher. Hopefully there is something that can be done.

stabone00 said:
Have you tried anything with it yet? There's quite a bit to it. The info is all searchable on here, you are looking for mediatek devices, sp flash tool, mtk droid tools. Let me know if you have adb and drivers installed. All the info needed for this unit is available , but there is a lot of info on mediatek devices, so it's a lot to look at. You need to have developers options enabled and oem unlocked and usb debugging on . If you can connect to your unit through adb, thats a start. Don't attempt anything with fastboot, it's not enabled on this unit. You'll then want to look for the modified version of mtk droid tools 2.5.3. If you are able to connect with that, I'll tell you what to do next. Not so sure my unit is recoverable, i've lost the startup atoto screen and can no longer connect with sp flasher. Hopefully there is something that can be done.
Click to expand...
Click to collapse
No I haven't done anything with it yet. I wasn't planning on rooting the device. The only reason it's not in my car already is it's been 10-20 F and I don't have a garage. I have the thing sitting on my kitchen table so I can play with it.
I'll look through the info and see what I can do.

smithkt said:
No I haven't done anything with it yet. I wasn't planning on rooting the device. The only reason it's not in my car already is it's been 10-20 F and I don't have a garage. I have the thing sitting on my kitchen table so I can play with it.
I'll look through the info and see what I can do.
Click to expand...
Click to collapse
I have it hooked up with two switches, one feeds constant and other switch, and other switch feeds acc. Rooting it isn't too bad, but if you look into how the sp flasher is used, you could make a stock rom before doing it. I'm hoping there are test points on the board that can be used to get this flashed again. I'm not sure how it got this far gone. I had it bootlooping at the ATOTO startup, tried to flash the original boot and recover, seems like it wiped the preloader.

Have you had luck in unbricking your atoto?
I'm thinking about buying one also buy would like to root with kingroot and put a recovery into stereo if it's possible. Let me know your success is possible.
Thanks
Steven

scoolro said:
Have you had luck in unbricking your atoto?
I'm thinking about buying one also buy would like to root with kingroot and put a recovery into stereo if it's possible. Let me know your success is possible.
Thanks
Steven
Click to expand...
Click to collapse
So far it seems to be a very solid unit. Rooting it isn't an issue. I had been trying different things with this unit and at one point I thought it was almost unbrickable. It still might be, just haven't found a solution for my issue (which was completely my fault), although I'm pretty confident there is one. There is a lot of info about mediatek devices on here, a bit different approach when flashing a custom recovery.
Overall I was liking the unit, hadn't seen any issues some of the others had. Hope to see more people getting involved.

I hope you get the unit working soon.
I'm thinking about getting the same unit and I want to root it so I can get ADAWARE and XPOSED app installed. I'm also thinking about getting a Bluetooth media steering control for it also.
I've only seen the Atoto A6 on Amazon.ca for about $280. Hopefully there is another site that sells cheaper.
Again good luck and keep us informed with your progress if possible.
Steven

Atoto offered a to replace the unit with the PB model, as this one is no longer available. After doing as much research as I did, I am certain that this can be fixed. There should either be a way for force the preloader or get into a meta mode/ flashing mode. I'm going to keep it and see. I'm ordering the PB as soon as it is available again on Amazon.

So driving home from work today, I noticed an update pending for the A6. Was in a good coverage area (using a MiFi hotspot, btw, not my phone), downloaded it at a long stop light, hit install, and after reboot, I got the dead Android ERROR! graphic. About **** myself, thought I might have bricked it. At the next red light, I did a reset (I keep a slim toothpick in the console now, for just such emergencies) and I'm back to the old November build.

I ended up sending my 62721p back and am waiting for the pb model.
Did you have it rooted?

stabone00 said:
I ended up sending my 62721p back and am waiting for the pb model.
Did you have it rooted?
Click to expand...
Click to collapse
Nope, couldn't be assed, it's basically a Poweramp/Waze/Spotify machine for me now, figured I don't need root for that, and all the cool root-level stuff the Rockchip and Sofia units get isn't available for this thing anyway.
Did get the update to stick the second time around, but noticed no changes in functionality. MCU got updated as well.

Seicane H276L -- What type HU is it? ROMs available?

Sorry for the n00b'ness of this post. I tried to post the link directly to the unit, but the forum is preventing me from doing so. If you search for "H276L" on seicane(dot)com, it's the more expensive (8-core) unit.
I'm highly considering buying this unit, but I want to make sure there are ROMs that are being developed for it. I had an MTCB Joying unit in my last car that worked like crap until I found a good ROM for it on here. If this unit's platform isn't being developed on here, I have no interest in buying it. Being a Jeeper, it'd be super handy to have my trail apps (Gaia GPS, AllTrails, etc.) run directly on my head unit, but if I'm going to spend $ on my HU, I'm gonna get one really worth my while.
TIA!
-A

Looking for Roms!
Hello,
I recently did purchase this unit and I have been extremely unhappy with the stock ROM. I am looking now to root the device later today (putting together a tutorial right now. I am still looking for a ROM however. The initial unit seriously has no apps that function fully. Every app force closes or doesn't function as expected. I am extremely technical and can usually fix any issues. I worked with Seicanes (non-existent) support for the last month with no success. They will require you to pay shipping to and return (so basically if you ship it back and want another you are spending a few 100 more). I am going to try and root and install custom ROM instead, if I can find one.
Thanks,
Brady
aklino said:
Sorry for the n00b'ness of this post. I tried to post the link directly to the unit, but the forum is preventing me from doing so. If you search for "H276L" on seicane(dot)com, it's the more expensive (8-core) unit.
I'm highly considering buying this unit, but I want to make sure there are ROMs that are being developed for it. I had an MTCB Joying unit in my last car that worked like crap until I found a good ROM for it on here. If this unit's platform isn't being developed on here, I have no interest in buying it. Being a Jeeper, it'd be super handy to have my trail apps (Gaia GPS, AllTrails, etc.) run directly on my head unit, but if I'm going to spend $ on my HU, I'm gonna get one really worth my while.
TIA!
-A
Click to expand...
Click to collapse

jerkface41606 said:
Hello,
I recently did purchase this unit and I have been extremely unhappy with the stock ROM. I am looking now to root the device later today (putting together a tutorial right now. I am still looking for a ROM however. The initial unit seriously has no apps that function fully. Every app force closes or doesn't function as expected. I am extremely technical and can usually fix any issues. I worked with Seicanes (non-existent) support for the last month with no success. They will require you to pay shipping to and return (so basically if you ship it back and want another you are spending a few 100 more). I am going to try and root and install custom ROM instead, if I can find one.
Thanks,
Brady
Click to expand...
Click to collapse
Thanks Brady,
Please keep me posted. I pulled the trigger on this guy 2 days ago -- waiting for it to ship. I had an Eonon unit in my Cadillac, and it was the same story. Support is useless, stock ROM is crap, but with the right ROM, it becomes awesome.
-A

aklino said:
Thanks Brady,
Please keep me posted. I pulled the trigger on this guy 2 days ago -- waiting for it to ship. I had an Eonon unit in my Cadillac, and it was the same story. Support is useless, stock ROM is crap, but with the right ROM, it becomes awesome.
-A
Click to expand...
Click to collapse
Hello,
After many trial and error attempts I was able to finally find an extremely amazing OS! Malaysk is the way to go once you get your Seciane Unit. Everything works fully and is extremely easy to use. The installation was really easy honestly and it didn't take long to get it to work correctly. If you go to: https://forum.xda-developers.com/member.php?u=3590033 you can view the forum based on the unit you have and get the correct firmware. I used the free (LITE) version for about 1 week and then decided to pay the $20 to the developer to get the full version (SO WORTH IT!!). @Malaysk did an amazing job and this is the way to go!
Thanks,
Brady

jerkface41606 said:
Hello,
After many trial and error attempts I was able to finally find an extremely amazing OS! Malaysk is the way to go once you get your Seciane Unit. Everything works fully and is extremely easy to use. The installation was really easy honestly and it didn't take long to get it to work correctly. If you go to: https://forum.xda-developers.com/member.php?u=3590033 you can view the forum based on the unit you have and get the correct firmware. I used the free (LITE) version for about 1 week and then decided to pay the $20 to the developer to get the full version (SO WORTH IT!!). @Malaysk did an amazing job and this is the way to go!
Thanks,
Brady
Click to expand...
Click to collapse
Brady, thanks for this link. I have h221 and it appears I might be able to use the rom. What I can't do is get into recovery, and I can't get into developers options. I'm on a stock Android 9 and for some reason, they disabled the ability to tap the build # seven times to get to developers options. Did you have this problem, and how did you get into recovery mode. I searched everywhere and tried all combos of holding the reset button, no luck. I emailed secaine but no luck so far. Any help appreciated, Thanks johnm

Update and recovery instruction
Great to hear! I actually had the exact same issue as you and I found that seicane was of no help. However I finally figured out how to get into recovery mode (don’t need to do anything with rooting or getting into developer options). To get into recovery you should have a pin hole reset button. Do the following steps.
1. Hold in reset button until unit powers off and you see side buttons blink (10-20 seconds it usually took)
2. Immediately after this happens let the reset switch go
3. Immediately after this hold in button again until lights blink once (about 1-2 seconds)
4. Press and release button a third and final time and it will boot into recovery mode. (Quick press release)
After I got into recovery I wiped cache, then factory reset, rebooted, installed the recoveryinstaller apk file (included with Rom download) it reboots you and installs new rom and you will be good to go!
Thanks,
Brady

OWNICE K6 SC9853i

It is almost a great head unit wit dsp and optical out, but have some problems:
- the music app is terrible, first of all the folders/track are showed not in alphabetical order
- the home screen cannot be changed
How could be replaced the stock music app, with similar music user friendly/modded music app like in Hal9k's px5 rom have?
How could it be rooted?
Thanks if anybody could help...

Here's everything you wanted to know but were afraid to ask (Open it with chrome and you should get the translation). Did you take any pictures of the insides of your HU I'm curious to see how they added a toslink to it.

nic2k said:
Here's everything you wanted to know but were afraid to ask (Open it with chrome and you should get the translation). Did you take any pictures of the insides of your HU I'm curious to see how they added a toslink to it.
Click to expand...
Click to collapse
Thanks!
If I would disassemble the hu, then I'll take photos of the inside of it...

ROOT
Does anyone have success with this magisk procedure?
http://icar.vn/forum/threads/huong-dan-root-dau-android-ownice-c960.3115/
In the thread no one says "success!" or "thank you!" like that, I want to get root but I'm scared of breaking my device.
And unfortunately I can't speak Vietnamese.
Attach an image showing my device's system. Thank you!

Hello; i just got this unit. I have not installed it yet.
Have you resolved your issues with it?
On which car have you installed it?
Cheers,
Francesco

I have the Ownice C960 K6 unit.
Do anyone knows how to change the apps that show on home screen ?
When I use the regular method of click and hold the icon, nothing happens...

warata said:
Does anyone have success with this magisk procedure?
http://icar.vn/forum/threads/huong-dan-root-dau-android-ownice-c960.3115/
In the thread no one says "success!" or "thank you!" like that, I want to get root but I'm scared of breaking my device.
And unfortunately I can't speak Vietnamese.
Attach an image showing my device's system. Thank you!
Click to expand...
Click to collapse
I'm icarvietnam, we have tried to root many C960, so in my theard no need to confirm succeccs
---------- Post added at 11:43 AM ---------- Previous post was at 11:42 AM ----------
aylone said:
I have the Ownice C960 K6 unit.
Do anyone knows how to change the apps that show on home screen ?
When I use the regular method of click and hold the icon, nothing happens...
Click to expand...
Click to collapse
You can install other laucher app, such as lova laucher

Ownice K6 SC9853
Hi! i bought an Ownice K6 SC9853 media but I completely stopped it, the image is normal but the interface is virtually inverted, I can't handle it normally. i want a hard reset but it won't restart, how is a total reboot possible?
Thanks!

Como podré reset en modo recovery para revivirlo se me a quedado frizado y no pasa del logo de Android

Help me please. With the Ownice K6 radio tape recorder, the device worked fine for 1.5 years, then it started. The problem is rebooted every minute and during the reboot the radio works and the volume is adjusted. Then a minute of normal work again reboots and so on in a circle.
What did I do for the solution:
1. flashed it with my native firmware. (which I received from the seller immediately after purchase)
2. I was flashing it with firmware from the seller SysSoftware_C960_K6_20200721.153132_OLS1 (I turned strangely after a year and a half and he sent a pistol the next day)
3. I was flashing the MCU) I also got it from him without any questions)
4. Installed a fan for cooling.
5. Disconnect everything from the radio except the power supply.
the result is the same reboot every minute.
can anyone come across a similar one or knows where to find a discussion of a similar problem.

speederi said:
It is almost a great head unit wit dsp and optical out, but have some problems:
- the music app is terrible, first of all the folders/track are showed not in alphabetical order
- the home screen cannot be changed
How could be replaced the stock music app, with similar music user friendly/modded music app like in Hal9k's px5 rom have?
How could it be rooted?
Thanks if anybody could help...
Click to expand...
Click to collapse
search " icar vietnam forum" , use google translator, and you found all what you want.

firvik said:
Help me please. With the Ownice K6 radio tape recorder, the device worked fine for 1.5 years, then it started. The problem is rebooted every minute and during the reboot the radio works and the volume is adjusted. Then a minute of normal work again reboots and so on in a circle.
What did I do for the solution:
1. flashed it with my native firmware. (which I received from the seller immediately after purchase)
2. I was flashing it with firmware from the seller SysSoftware_C960_K6_20200721.153132_OLS1 (I turned strangely after a year and a half and he sent a pistol the next day)
3. I was flashing the MCU) I also got it from him without any questions)
4. Installed a fan for cooling.
5. Disconnect everything from the radio except the power supply.
the result is the same reboot every minute.
can anyone come across a similar one or knows where to find a discussion of a similar problem.
Click to expand...
Click to collapse

_C960_K6_20200721.153132_OLS1 is the worst firmware possibile, go to icar vietnam forum and use the firmware from april or march

nick1964 said:
_C960_K6_20200721.153132_OLS1 is the worst firmware possibile, go to icar vietnam forum and use the firmware from april or march
Click to expand...
Click to collapse
Thank you very much for your answer. found a lot of interesting things there. I will experiment on the weekend

ngochoangimsat said:
I'm icarvietnam, we have tried to root many C960, so in my theard no need to confirm succeccs
---------- Post added at 11:43 AM ---------- Previous post was at 11:42 AM ----------
You can install other laucher app, such as lova laucher
Click to expand...
Click to collapse
Can you please help me? i have the one with rotatble screen, when i flash the one you rooted, the rotation od screen goes crazy, and cannot root mine, can you help please?
this the firmware i have
V11.1.1_20200427.165106_OLS3-HV-1280x720-SC9853
thanks

nick1964 said:
_C960_K6_20200721.153132_OLS1 is the worst firmware possibile, go to icar vietnam forum and use the firmware from april or march
Click to expand...
Click to collapse
nothing helped the result is the same every minute reboot. I do not know what to do. what is the minimum voltage required for the device to work? I get 11.58v on my device, I think it's not enough.

firvik said:
nothing helped the result is the same every minute reboot. I do not know what to do. what is the minimum voltage required for the device to work? I get 11.58v on my device, I think it's not enough.
Click to expand...
Click to collapse
No, it's not enough, maybe you ave problems of battery. On mine, after U played about 3 hours with the HU in the car without start the engine, it beniged to shut down, I started and it shut down; after I understood the the battery was discharged.
Without 12,5 volts or more, it didn't work(and it's normal).

firvik said:
nothing helped the result is the same every minute reboot. I do not know what to do. what is the minimum voltage required for the device to work? I get 11.58v on my device, I think it's not enough.
Click to expand...
Click to collapse
Check your car battery, it's not enough.

thank. I'll try at home from the power supply

nick1964 said:
Check your car battery, it's not enough.
Click to expand...
Click to collapse
checked with a voltage of 13v, the effect is the same. the seller replied. writes that there is a problem with the power board in the device. is it possible?

mediatek 6735 stuck in start up screen

Help all, While trying to get root access (I managed temporary sofar), and removing some apps after that (as I still didn't got the desired result : have my custom launcher as default) the unit is stuck at startup.
It's running on android 7.0, model, for what it's worth ; an alps hla1280 *480, 4gb ram, 32gb storage.
Before this happened I tried to connect to the unit trough my laptop but never succeeded. Hope someone can help!
I already did a hard reset, and took the power off, but no result.

A friend of mine got tha same mt6735 from mekede but he has the real Android 9 (CPUZ)
I'm in same situation as you but without rooting...
Really wanna try to get a custom launcher to replace the actual one (with the white ball for menu) but i'm so scared to brick it like you... Hope someone gonna help you
Look like this CPU isnt really common on the server

AxoO69 said:
A friend of mine got tha same mt6735 from mekede but he has the real Android 9 (CPUZ)
I'm in same situation as you but without rooting...
Really wanna try to get a custom launcher to replace the actual one (with the white ball for menu) but i'm so scared to brick it like you... Hope someone gonna help you
Look like this CPU isnt really common on the server
Click to expand...
Click to collapse
It's quite disappointing that no one reacts.. Guess it's not the mcu people want to help for. Or they think we should search at xda but nothing helpful to find.

muish002 said:
It's quite disappointing that no one reacts.. Guess it's not the mcu people want to help for. Or they think we should search at xda but nothing helpful to find.
Click to expand...
Click to collapse
Can't even use Carplay dongle lol my usb isn't recognized :/