After hitting a pothole my unit turned off and the OS never booted again. Still, I could apply updates but always got stuck in a boot loop.
I've tried sending it to a repair shop but they totally ruined the "vol" and "rx" terminals and now can't even get into recovery mode. There's a thread by marchnz about PX5 units where he describes how to transfer firmware by enabling OTG, by wiring a usb cable directly to the pin header.
Does anyone have the header's pinout for this model?
I tried contacting Klyde through AliExpress but they only instruct me to try updating it.
Related
Hi,
I Bought this android head unit a month ago. After having some problem with apps i decided to set head unit to factory settings. After that i got stuck on bootloop
I trie reseting it via RST button but, that didn't helped. So i think i need somehow to get into recovery for data wipe. None of button combination leeds me there.
Does anybody now, how to get into recovery mode ?
i Have video uploaded into youtube, but as im new in this forum, i can't paste it here.
youtube com/watch?v=_zYjHY9D0kc
Tried:
- various button combination (reset, reset + power, etc)
- Connect USB male<->male connector to head unit and PC. No response, pc wont find new device (android adb)
- Solder wires to pins on mainboard GND, VCC, D+, D- and connect to pc. No response
- contacted seller. He aproved that android is stuck and head unit needs to be restored from update (or data wipe out). Seller asked me for my email, but its already two weeks after this problem and still no instruction what to do.
Please HELP!!! ((
Isudar h53
hello did you solve the problem? I have the same
Hello!
I've recently got a Silverstrong Android 9 Head Unit: https://www.aliexpress.com/item/32822937592.html?spm=a2g0s.9042311.0.0.328e4c4dWZb7Fi
Can someone help me on how to get adb access or a custom recovery (mainly for rooting purpose)?
I have to mention that I've tried connecting a notebook with adb via and USB cable (male USB type A to USB type A), but it seems nothing happens. I can tell that the unit's USB ports are working for USB sticks.
I have also tried some combination implying the reset hole present on the front, but I couldn't make it work.
Any help is appreciated! Thanks!
Edit: I have to mention that the unit packs a MediaTek MT8321M if it matters.
Just an update: I have followed the instructions provided here for rooting: https://forum.xda-developers.com/showpost.php?p=76725981&postcount=740 . Everything went well until I tried to reboot the device. Now it is stuck in a bootloop (it passes the kernel bootlogo but it is stuck on Android bootlogo) and I really need to access its recovery. It would be my only hope to try to unbrick it. Unfortunately the only physical switch of the unit is just a reset hole on the front which will cut the power right away (tried multiple pressing combinations, none worked). I really need to enter recovery mode and I am pretty desperate, so any advice is welcome. Thanks!
I couldn't make it boot into recovery mode, but it did boot when I placed on a usb stick a file named "ZQ_MTK1B_UPDATE_HeXinDa_EN_8003_08152051.zip" and then it started to flash it automatically. After the flash completed, the unit recovered from bootloop, but now it seems there is no sound and no radio. I posted all of this just in case somebody ever will have to deal with same kind of trouble. It seems the unit is actually branded as alps ZQ8003 and I will ask the seller for some firmware/more technical info.
Hi, I have the same problem. Did you make it?
I just bought a Belsee Tesla style Android head unit with PX6 (double din, 1980*1080, 4G, 32G)
After installation for about 1 h, and I changed the boot logo to a new high resolution one. Then it did not work, stop at boot logo
The seller has send me a px6_format zip file and let me put it into a disk, plug the disk and restart the unit to recovery. But this method did not work. The unit kept at logo with no reaction.
I also tried many other method to try to enter recovery mod, but no luck.
Who can help me with this? Happy to pay for it! Thanks
pictures of this unit attached
ibb.co/z225dCS
ibb.co/StL3zwS
ibb.co/SvCYCzx
ibb.co/4FdgX4r
Did you try use a pin to reset the unit?
Also, where did you plug in the USB with the new update PX6 zip?
Try to put it in the USB slot on the unit, not the two from the connection cords.
JohnnyMHo said:
Did you try use a pin to reset the unit?
Also, where did you plug in the USB with the new update PX6 zip?
Try to put it in the USB slot on the unit, not the two from the connection cords.
Click to expand...
Click to collapse
I've tried every method, but no luck.
I removed the core board, and post it to the seller for an exchange. Then it works again. But the radio now cannot find any channel.
Terrible head unit, strongly suggest every one do not buy this type of trash.
Hi is there anyone on these forums that can repair one of these chinese units
I have one of these https://www.ebay.co.uk/itm/384770479698 in my 2006 Merc. its a MTK8667 Android 11 based unit. FF_866X is the device name, i'm sorry I do not know the MCU
I was sent some update files from the seller https://we.tl/t-UeDC40i6Ul XRC-8667 升级软件 Q腾实UI多合一-国外-1280x720_v32_20220223
during the update process it copied the superimage ok but then something came up in red but it came up to a kind of recovery and said erasing... it then rebooted it gets to the car logo screen, before android screen then goes to a blank screen with the following in bottom left corner...FASTBOOT MODE and wont go any further
I have pressed RST then two fingers on screen until i get "detected" but all i get is the same fastboot mode again,
I have redownloaded and extracted the firmware and reformatted my usb drive to fat32 and tried the whole process again and tried in both usb slots but no sucess.
I have obtained other mtk8667 firmware files 8667.bin and 8667.upd from this topic https://forum.xda-developers.com/t/firmware-junsun-v1-8667q-8g-128g-vhd-qled.4405475/ on this forum but I have tried many different ones and it just wont read the usb, still just goes straight to fastboot mode....is anyone able to help me I have messaged the seller but no reply
So far I have tried about 7 or 8 different firmware versions, the sellers own, some junsun versions, ossuret versions even xtrons versions(all in correct format of 8667.bin and 8667.upd on root of usb formatted to fat32 but it does not read the usb.
The usb slots are still working as I can plug my phone in and it charges but the unit does not seem to have a full recovery mode
I have tried using a program called adb and fastboot on the computer but will not connect to the head unit
I have manually installed MTK drivers to the computer and tries a program called magic thunder but again would not connect to the unit.
I have tried to find a memory dump online but nothing, all I can find for mtk8667 is firmware consisting of 2 files 8667.bin and 8667.upd
I have now removed the unit from the car so i tried removing everything but 1 usb slot and removing the power for 10 mins before powering up and attempting to flash again
So i think i'm in need of expert help, so i'm looking for a repair shop, or person that can take the unit and hopefully get it working, more than happy to pay a fair fee and to post it to you, or if you are within a couple of hours travel from Yorkshire(Leeds area) I will happily come to you
Hello people
I ain’t so sure if I got ts18 or ts10 I can’t access the head unit to check, anyways I’m failing to boot my head unit it stuck on the logo
I tried to download fixes via seller’s website
And just never mind what what I tried it always ended the same
I tried to force and update via ignition method with rst button, and via attaching key1 wire to ground/negative
I got 2 usb ports one of them finishes the update so quick and do nothing
And the other one fails and write me this”init fat32 storage fail”
Hello any solution?
Murdysouly said:
Hello people
I ain’t so sure if I got ts18 or ts10 I can’t access the head unit to check, anyways I’m failing to boot my head unit it stuck on the logo
I tried to download fixes via seller’s website
And just never mind what what I tried it always ended the same
I tried to force and update via ignition method with rst button, and via attaching key1 wire to ground/negative
I got 2 usb ports one of them finishes the update so quick and do nothing
And the other one fails and write me this”init fat32 storage fail”
Click to expand...
Click to collapse
Hey there,
If the update completes really quick, maybe it's because it isn't going properly.
Try various other usb sticks.
Normally you should have the time to read every steps during the update "writing partition blabla1, writing partition blabla2 ..." aso asf.
I had to try a dozen usb sticks before finding one that worked for me.
May be worth the try.
Godspeed