T550 Hard Bricked QHSUSB_BULK - Samsung Galaxy Tab A series Questions & Answers

Hi everyone,
I have a Galaxy Tab A 9.7 T550 that seems hard-bricked. No visible (or audible) sign of life when trying to power on. Device does charge (checked with USB ammeter and voltmeter at battery). When plugging into computer it shows up as QHSUSB_BULK.
I did some searching and it seems that sometimes devices in this state can still boot directly from an SD card with proper partition structure on it. However, I couldn't find an image from a working T550. Does someone still have a T550 lying around from which they could provide me with a dump of the emmc to try?
Or any other suggestions are welcome too!
Thanks in advance!
UPDATE:
I managed to get QPST up and running and the tablet seems to be recognized properly by it. However, also for it I couldn't find an image file that I can flash. If anybody has one lmk
UPDATE 2:
I realize I should've included some more information so here is some more:
I tried using Odin to flash a stock firmware but the device won't boot into download mode, recovery, or regular OS. When plugging it into a computer it is not recognized by Odin.
It is recognized in QPST as "Q/QCP-XXX (Sahara Download)" (see pic below).
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
However, it only allows me to select an AP image for download, the BL option doesn't seem to be working, the buttons don't give any reaction. Also, QPST wants one of .hex, .hxb, .pbn, .bin, or .mbn file. I did try simply flashing the Odin AP .tar.md5 in QPST but it recognizes it as invalid. I did notice that various system images can be extracted from the Odin flashable firmware files, including some .mbn files. However, the AP file for Odin yields only the following:
boot.img
modem.bin
persist.img.ext4
recovery.img
system.img.ext4
These don't seem to be correct for flashing through QPST.
The Odin BL file yields
aboot.mbn
hyp.mbn
NON-HLOS.bin
rpm.mbn
sbl1.mbn
sec.dat
tz.mbn
These look promising, only the BL option in QPST still doesn't work for me.
I also did read about using an XML file in QFIL to flash specific images to specific partitions on the device. I found an example XML here but I don't know the partition IDs the images need to go to.
The other idea with an SD card I think could also still work (along the lines of this or this). But I would need a debrick image to write to an SD card.
So yeah, I don't think there's a high chance of being able to revive the device, simply because the correct firmware files aren't (easily) accessible. But if anybody has any wisdom to share on it let me know.
Thanks in advance and enjoy your day!

First, you didn't search for a ROM obviously since the first google result is this.
Second, you don't use QPST with samsung devices, you use ODIN.
Third, since you lack the skills to deal with this I'd recommend sending it to a professional, however if you insist on fixing it yourself.
Then follow this guide. Specifically the second method, and don't download that scam tool in the third method.
On a side note: Learn how to search, it will save yours and others time.
Goodluck.

XDHx86 said:
First, you didn't search for a ROM obviously since the first google result is this.
Second, you don't use QPST with samsung devices, you use ODIN.
Third, since you lack the skills to deal with this I'd recommend sending it to a professional, however if you insist on fixing it yourself.
Then follow this guide. Specifically the second method, and don't download that scam tool in the third method.
On a side note: Learn how to search, it will save yours and others time.
Goodluck.
Click to expand...
Click to collapse
Thanks for your reply!
Sorry I should've said this earlier but I had tried flashing with Odin. The problem is that Odin won't recognize the device (and yes I do have the drivers installed).
For me, it's not really worth sending to a professional so I thought I'd try myself.
I should've really included more information in the first post, so I'll add some more there now.

Artificial_Intelligence said:
Thanks for your reply!
Sorry I should've said this earlier but I had tried flashing with Odin. The problem is that Odin won't recognize the device (and yes I do have the drivers installed).
For me, it's not really worth sending to a professional so I thought I'd try myself.
I should've really included more information in the first post, so I'll add some more there now.
Click to expand...
Click to collapse
So you can't even boot to download mode? Maybe charge your phone for 10 mins or more, or try to boot by connecting the phone while pressing both volume buttons.
If you still fail to boot into download mode, then take it to a service center. No one can help you except them.

XDHx86 said:
So you can't even boot to download mode? Maybe charge your phone for 10 mins or more, or try to boot by connecting the phone while pressing both volume buttons.
If you still fail to boot into download mode, then take it to a service center. No one can help you except them.
Click to expand...
Click to collapse
Exactly! Tried both and no success. I guess you're right, I won't be able to fix it.
But thanks for your help!

Related

Can you help me figure out my provlem w/ Phone

Yesterday my phone just went pitch black when i was using it tge only lights on were the back button and the menu one beside the home button. Nothing worked. Power. 3 button both recovery and downloading. So i pulled the plug and took the battery out. When i turned it on i noticed my theme went back to the stock one. All my user data was erased. No apps were installed. Market maps and youtube have an icon on main page but say "application not installed on phone" when i click on it. My camera wont work either it says "Turn off usb storage before using camera" when i go to my gallery/music player/video player/voice recorder it says "SD card unmounted or not present" and when i use My files it says "Your phone does not have an SD card inserted"
Has anyone seen problems like this at all? If so can you tell me how to fix it please cause this phone was hella expensive and all it is right now to me is an expensive phone bill that i cant use features for...
Are you using an external sd card?
Sent from my GT-I9000 using XDA App
I have one but its not in the phone. I took it out a week or two ago.before it happened
Are you familiar with 'Odin' ??
Get your self a firmware and flash it, and see how you get on.
You do have the 3 button combo right ?
Yes my 3button combo works. and i know how to use odin. can you point me into the direction of the latest firmware for bell. cause if i need to return it they will see if its on their firmware and stuff.
When im using odin i get this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
is that ok to have the 2 coms? cause everytime ive used odin before it has always had only 1
dont use PIT file unless you have all 3 files...
So remove the PIT and flash and you should be ok. Most firmwares now only come in 1 .tar file so dont worry about it...
If the flash doesnt fix your problem, you will need all 3 files and PIT, but im not familiar with bell firmwares so you may have to do a bit of searching for that one.
This is what i have.
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
and its stuck on that. I have the I9000UGJL2.tar file in the phone part but nothing is happening.
Will a hard reset bring it back to factory settings?
I have the I9000UGJL2.tar file in the phone part
Single file its PDA in Odin unless its a modem file .
jje
Ok well ****.... Odin didnt work. so im trying to spoof with kies right now but something very very weird is happening. it says instalising... and it goes like this 1...2...3...4... homescreen for a split second. then instalising... and it goes like this 1...2...3...4... homescreen for a split second. and repeat... is my phone kinda screwed at this point?
ok... well my phone is only showing
the first screen you see when you boot.
Galaxy S GT-1900
Samsung
Is it ****ed for good now?
Gordon_Jeffries said:
ok... well my phone is only showing
the first screen you see when you boot.
Galaxy S GT-1900
Samsung
Is it ****ed for good now?
Click to expand...
Click to collapse
No its not ****ed, dont panic.
Is your download mode still working ??? Do as i said earlier with all 3 Files and PIT.
Then in Odin CHECK RE-PARTITION and when you have all 3 files + PIT loaded i.e PDA, Phone, CSC, connect your phone (in download mode) and flash it.
Make sure you Have all 3 files and make sure they are in the right section. And also make sure the firmware that came in 3 files is supportive of Bell SGS
PIT goes in PIT
PDA goes in PDA
MODEM goes in PHONE
CSC goes in CSC
@Gordon_Jeffries
Please check the followings:
* Use only the original Samsung USB-cable.
* Restart your PC and move the USB cable to another USB-port.
* Without using Odin,put the phone on download mode and connect to your PC, let your PC install the drivers, disconnect when done.
* Start Odin and load the firmware file without a pit file and no re-partition.
* Re-enter download mode, if the phone is still on download mode then you need to hold the three buttons until the phone re-enters download mode, connect to the PC and flash the firmware.
* If the flash goes well then do a wipe/factory reset from recovery.
ok well i can get it to download mode. but i dont have the CSS and or phone. does anyone know what the most current up to date bell firmware is?
it doesnt have to be a new firmware release...
Does Bell not have a single firmware in all 3 files ??
as a last resort you can use darkys resurrection (odin version) That comes in just 1 .tar file and you can use 512PIT with it..
I have used it many times to get me fixed up.... And im sure its compatible with bell (but check first)
Ive tried everything. JL2, JK3, Jk4, JH2, JPY, Darkys resurection. nothing works it just continues never ending boot screen...
Gordon_Jeffries said:
Ive tried everything. JL2, JK3, Jk4, JH2, JPY, Darkys resurection. nothing works it just continues never ending boot screen...
Click to expand...
Click to collapse
Can you enter recovery mode? If you can then do a factory reset, if that does not help and you have a 16GB Internal SD-card, then it's very likely that Internal SD-card of your device is dead.
No i cant enter recovery mode anymore. and yes i have a 16gb internal SD-card.
thats what i was hoping it wasnt... ok well i phoned bell and they said they will bring it in for sercive.
Same problem here
I have the same problem here, but i have a I9000B (Brazil) i just want to take my phone back to normal, can anyone help me?
My actual firmware: 2.3.3 I9000BVJJWW2 (its the offical one, from Kyes)
I'm not familiar with odin, but if u give any tutorial that I can follow, will help alot.
Thanks
tjacobs said:
I have the same problem here, but i have a I9000B (Brazil) i just want to take my phone back to normal, can anyone help me?
My actual firmware: 2.3.3 I9000BVJJWW2 (its the offical one, from Kyes)
I'm not familiar with odin, but if u give any tutorial that I can follow, will help alot.
Thanks
Click to expand...
Click to collapse
What you could do, is go to samfirmware.com, register and search for i9000. Or if you want to download a i9000b rom, press this link: http://hotfile.com/dl/146652827/84f8d47/I9000BVJJV3_I9000BSAMJV2_SAM.zip.html
(password is: samfirmware.com)
Just use odin to flash.
Or: http://forum.xda-developers.com/showthread.php?t=1102881&highlight=+guide+odin
(PS, search is your friend )

[Q] Cannot flash Galaxy S4 GT-I9502?

Hey Guys,
I am trying to return a Galaxy S4 Duos GT-I9502 back to stock, for someone who attempted to root the device, which failed. I am however experiencing some difficulty doing so, and would appreciate some help, if anyone has any suggestions.
This is the screen on the device:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I am able to put the device into download mode, though I keep getting this error message when I try flashing the device in Odin.
"Complete(Write) operation failed."
When attempting to flash the device, it quickly goes through boot.img, recovery.img and system.img (when it should take longer for each step, and you should see the little green progress bar move), before failing. Does this mean that Odin is having issues writing to the device?
I am pretty confident that I have the correct Samsung drivers installed, and I have tried completely closing all of the Samsung Kies processes on the computer. I have even tried using a different computer, and two different ROMs.
I have tried flashing the below ROMs:
I9502ZNUBMG2_I9502CHUBMG2_CHU
I9502ZNUAME3_I9502CHUAME3_CHU
I have also tried the 'Firmware upgrade and initialization' option in Samsung Kies, though I keep on getting this error message, before it closes (I do not know what it says, Google translate doesn't give a good translation).
"Binary files are not registered U.S. Congress gyeongmu mouth mid-sprocket
Bow can proceed
Please check the binary file registration myeobu"
Does anyone have any suggestion / idea of what is going wrong? Any help would be highly appreciated!
Never mind, I was able to resolve the issue by re-flashing CWM recovery!
same problem
i have exactly same problem with I9502ZNUBMH4 version , does anyone know how to flash this device because i tried 100 time with different versions of odin , and every time i failed repaird it with cwm .
oh and the device won`t do a full wipe , every time i full wiped it my files didn`t deleted ?!
Samsung S4 GT-I9502 root / flash failed - HELP
Hey Guys,
I tried to root my Samsung S4 GT-I9502 (OS Android 4.3), for that I found this website:
http://marrkdaviid.com/2013/08/fix-caller-id-install-google-play-on-the-galaxy-s4-i9502/
But it failed (see more Information below) and I had the following error message and no wifi.
"Complete(Write) operation failed."
When attempting to flash the device, it quickly goes through boot.img, recovery.img and system.img (when it should take longer for each step, and you should see the little green progress bar move), before failing. Does this mean that Odin is having issues writing to the device?
I live in China and I just bought the phone, I needed 5 days to download the necessary files, because most download pages are blocked in China. So I am loosing my last nerve right now.
I am pretty confident that I have the correct Samsung drivers installed. I don’t have Samsung Kies installed. I have even tried using a different computer (Laptops), and two different ROMs.
I have tried flashing the below ROMs:
I9502ZNUCMG2_I9502CHUCMG2_I9502ZNUCMG2_HOME.tar.md5
I9502ZNUEMK3_I9502CHUEMK3_I9502ZNUEMK3_SVA.tar.md5
Someone with a the same problem tried the 'Firmware upgrade and initialization' option in Samsung Kies, but it didn’t work, so I didn’t try. (Here the link: http://forum.xda-developers.com/showthread.php?t=2382979)
Instead I tried a recovery. I used Odin 3.07 and the following file:
i9502-cwm-recovery.tar.md5
I got my phone back to work for a while, I reset the phone, just in case. But know I can’t switch the Wifi on and the phone wants to Reboot.
So I allowed the phone to Reboot, I clicked on “reboot system now” and then on “Yes – (I forgot what was written behind the Yes, but I didn’t just click on the normal Yes, I clicked on the Yes - …)
The problem here: The Phone changed to a China Unicom Screen and stayed like that. After 5 h I took the battery out, but I couldn’t restart the phone.
So I did an cwm recovery and know I am afraid to reboot. The Wifi is not working and I can’t find any information about how to fix it.
So please help me. Do I reboot? Can I already install SVA ROM, although I couldn’t flash the Stock Firmware? Do I send the phone back and give up?
Please let me know if you need any other information to be able to help me.
PS: This is the first time that I flash a smart phone. And although I already spent several days now, searching the internet for how-to-dos, tips & tricks, guidelines, Q&As and god knows what, I still do not fully understand what exactly I am doing here. Hence, I would be very happy to receive somewhat easy understandable answers.
Thank you so much for your help!
Anna
Philz 6.00.2
I have a similar problem.
I tried to install philz _touch_6.00.2-i9505.tar, by uisng Odin 3.09
Everything went OK. I got PASS! and my Samsung S4 i9505 rebooted into the stock ROM
However I cannot enter Philz. I tried to keep pressed volume Up + Home + Power but the phone goes immediately into the main Samsung screen. I have tried many combinations...the only working combination is:
volume Down + Home + Power > which leads to download mode (for Odin)
Thank you for your suggestions!
SA
Same problem, how did you fix it?
I have the same issue, how did you fix it? It's been a day that I've been trying to fix it. I've got the Exynos version I9500

[SOLVED] Can't boot, can't boot recovery, oem locked, usb debugging disabled

Happened when I was updating twrp:
I downloaded the .img from their website, booted into my older version of twrp, went to flashing pressed the butting in the bottom right corner, selected the file and selected 'recovery'
Said it was successful, so I rebooted, then it wouldn't do anything anymore except for fastboot.
1. Can't boot into recovery
2. Can't boot normally
3. USB debugging disabled
4. oem locked
Only thing I can enter is fastboot.
I followed this guide, but no luck on my end.
https://forums.oneplus.net/threads/...ck-guide-for-a-hard-bricked-oneplus-2.347607/
Have you tried this?
http://forum.xda-developers.com/oneplus-2/general/guide-return-op2-to-100-stock-unbrick-t3229606
and
All in one toolbox by mauronofrio.
I my self had lost recovery myself and flashed stock image in toolbox and then flashed image from above link to restore to stock and started custom rom process again.
Should not erase twrp once recovered if it has reflash your previous version of twrp or hybrid version.
Hope this helps.
passion8059 said:
Have you tried this?
http://forum.xda-developers.com/oneplus-2/general/guide-return-op2-to-100-stock-unbrick-t3229606
and
All in one toolbox by mauronofrio.
I my self had lost recovery myself and flashed stock image in toolbox and then flashed image from above link to restore to stock and started custom rom process again.
Should not erase twrp once recovered if it has reflash your previous version of twrp or hybrid version.
Hope this helps.
Click to expand...
Click to collapse
It's no use because oem is locked. That means I can't flash anything.
toolbox should still help you unlock bootloader again
Just use the Qualcomm factory restore image to return the phone to original shape of things.
passion8059 said:
toolbox should still help you unlock bootloader again
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
pitrus- said:
Just use the Qualcomm factory restore image to return the phone to original shape of things.
Click to expand...
Click to collapse
I have no idea how I would do this without being able to flash anything.
Do you mean that the Qualcomm download program also crashes like fastboot? Sounds like you either have some problems with your windows installation or perhaps you haven't searched for and downloaded the Qualcomm restore if your still trying to flash the ordinary way instead of the emergency way.
Was able to fix it when I was messing around. Not sure what I did but it worked.
Thank you for all your help guys
Theevilsocks said:
Was able to fix it when I was messing around. Not sure what I did but it worked.
Thank you for all your help guys
Click to expand...
Click to collapse
I'm having this problem too, and this isn't helpful. What were the last steps, or at least some of them, that you took to get it working? Which toolkit/script/program were you using? etc
Redjax said:
I'm having this problem too, and this isn't helpful. What were the last steps, or at least some of them, that you took to get it working? Which toolkit/script/program were you using? etc
Click to expand...
Click to collapse
I used this tool: http://forum.xda-developers.com/oneplus-2/general/guide-official-op2-stock-reset-to-oos-3-t3402020
I fiddled around a bit with it, but I'm not sure what I did, and I already deleted the files.
Theevilsocks said:
I used this tool: http://forum.xda-developers.com/oneplus-2/general/guide-official-op2-stock-reset-to-oos-3-t3402020
I fiddled around a bit with it, but I'm not sure what I did, and I already deleted the files.
Click to expand...
Click to collapse
Literally JUST finished with this guide, and my OP2 is alive again! I was going to come back and post. Thanks for the link.
Anyone trying to use this guide without success:
There's one very important step I somehow missed. You MUST disconnect your phone, hold the power button for ~15-20 seconds until it's off, and hold the Volume+ button, THEN plug it back in. Your computer will make the "device connected" sound, but the screen will stay black. THIS IS OK! That means you're in a special recovery, which is where you need to be for the tool.
I also installed the certificate file in the folder I downloaded, then rebooted (it did not work before a reboot, but did work after).
So, the steps:
1. Download the files, make sure your signature signing for drivers is off.
2. Install the trusted certificate, then the driver.
3. Reboot PC
4. Power off phone (hold power for 15-20 secs), hold volume+, then connect through USB (wait for device connected sound, screen on phone will still be black)
5. Run the tool (I ran as admin, not sure if that's required)
6. Weep with joy that you finally found a solution that works.

Tmobile samsung galaxy s7 upload mode

My tmobile galaxy s7 got stuck on something like bbl error and in the center of the screen the android logo and the sbl error and upload mode nothing else not able to get on download mode or recovery mode totally stuck need help odin not able to flash anything none of the latest firmware nothing,..
Ehat i did was i flash with odin a verizon firmware or something like fof6 combo firmware with the latest tmobile firmware found on androidfilehost.
My phone is now bricked or what i call softbricked i need any kind of help on how to flash or a tool to forcely flash something to unbrick and be able to restore stock firmware any nice developer please help i still paying this s7 and i really want to revive my phone any help will be greatly appreciated?
I'm no expert by any means, just a dude that was in the same position a few weeks ago.
First you'll want to get ODIN, which is your flashing tool:
http://forum.xda-developers.com/attachment.php?attachmentid=3804544&d=1467772303
Next you need to find the stock firmware. Lots of sites will have it but 99% of them use some kind of bandwidth throttling crap. The firmware is 4.5gb uncompressed and about 2gb compressed. So if you can find someone hosting the firmware on their Google Drive that's your fastest bet, otherwise it'll take hours or days to download.
The latest firmware at the time of this post is G935TUVU4APIA. You don't necessarily need the latest, you just need to get your phone restored. If there is newer firmware available than what you flash to your phone, when your phone successfully boots you'll get an update to the latest.
Wish I could find a direct link for you but it seems these will always be moving around. That being said search for TMB-G935TUVU4APIA-20160927113301.zip. That was the file I downloaded and it contained the 5 files listed below, which you should extract to your preferred location on your PC:
AP_G935TUVU3APG1_CL8439036_QB10213096_REV02_user_low_ship_MULTI_CERT.tar.md5
BL_G935TUVU3APG1_CL8439036_QB10213096_REV02_user_low_ship_MULTI_CERT.tar.md5
CP_G935TUVU3APG1_CL8439036_QB10213096_REV02_user_low_ship_MULTI_CERT.tar.md5
CSC_TMB_G935TTMB3APG1_CL8439036_QB10213096_REV02_user_low_ship_MULTI_CERT.tar.md5
HOME_CSC_TMB_G935TTMB3APG1_CL8439036_QB10213096_REV02_user_low_ship_MULTI_CERT.tar.md5 (optional)
The first 4 of the 5 listed above are the important ones. The 5th file, "HOME_CSC...", from what I understand preserves your data should you need to flash over a working phone, but we'll ignore that file for this task. Note the "AP", "BL", "CP", etc., at the beginning of each filename - more on that shortly.
Finally, the home stretch.
* Power off your phone completely. If you're boot looping hold VOL DOWN and POWER.
* Boot into recovery mode by pressing and holding VOL DOWN, HOME and POWER at the same time. Release when you see recovery mode warning.
* Connect your phone to your PC.
* Open ODIN and make sure the phone is recognized. It will show up under ID:COM and have some assigned COM port like 9 or 10.
* Click on the BL button and select the BL_G935TUVU3APG1_CL8439036_QB10213096_REV02_user_low_ship_MULTI_CERT.tar.md5 file from your extracted firmware package.
* Repeat this process for AP, CP, and CSC files.
* Once all files are selected click START.
After some time your phone will be flashed with the stock firmware and everything should be back to the way it was when you purchased it. Hope that helps!
---------- Post added at 11:26 PM ---------- Previous post was at 11:20 PM ----------
Sorry man, I can't read! Missed the part where you said you already tried ODIN.
You may want to do a factory reset first before flashing. I think you hold VOL UP, HOME and POWER to get there. Follow the steps to do a factory reset. Then try ODIN again with stock T-Mobile firmware.
tmobile s7 upload mode
the problem here is when I press vol up or vol down it goes straight to this
sbl error upload mode
and Odin detects as download mode but cant not flash anything I do have the latest firmware.
I will attach the picture of the actual error
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
https://imageshack.com/i/pnI8ZKLZj
tmobile s7 upload mode
this was the file I flashed before this happens
found it on android filehost under the search of G930T
https://www.androidfilehost.com/?fid=529152257862666887
it may give some directions thanks
Sorry my friend, wish I could help here. It looks like your bootloader is jacked. Did you mean "sbl" instead "bbl" error? I think that's the secondary bootloader. And from the file you linked it appears you flashed the Galaxy S7 "flat" (G930T) firmware onto your Galaxy S7 Edge (G935T). Never thought that would be a brickable operation but apparently so. Unless someone's dealt with this before your only option may be to return the phone and see if they can either reflash it with some other proprietary tool or exchange it. I don't know how to push the stock boot.bin and sbl.bin onto these phones but maybe someone here does.
tmobile s7 upload mode
yes sir is a flat version of the s7
and what you are saying is correct.
well I will sit and wait for something to come up wit a light thanks...
well I think I fried thos device just gonna sit and wait for a developer to find some source of code to reboot this thing
does anyone knows how to fix this problem " SBL error upload mode " ? please........... thanks

Solved - Can't boot into Recovery - Help needed for Installing Lineage OS

Hello everyone,
I might have messed up big time so I need your expertise on installing Lineage OS.
So I was following this guide for installing Lineage OS 19. However, I stuck here:
Manually reboot into recovery, this may require pulling the device’s battery out and putting it back in, or if you have a non-removable battery, press the Volume Down + Power buttons for 8~10 seconds until the screen turns black & release the buttons immediately when it does, then boot to recovery:
Reboot and immediately hold Volume Up + Power while the device is connected to a PC via USB cable.
Click to expand...
Click to collapse
I did everything correctly till here but when I try to boot into flash, I can't. I go into download mode, flash lineage recovery using heimdall, then re-start to boot into recovery but it does not, keeps looping through the images below. Now I can't turn off the device, I am just stuck at download mode. It behaves like there is no OS or recovery mode. Like storage chip is empty to the last bit. I might have wiped data before installing lineage recovery. Please help. Thank you.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
First off: which Tab S6 Lite is this? 2022 version (Qualcomm) or Pre-2022 (Exynos)?
Secondly: Perhaps try flashing with Odin and following the LineageOS guide for your respective device (Qualcomm/Exynos) rather than relying on the instructions from the LineageOS page.
dumdedumda said:
First off: which Tab S6 Lite is this? 2022 version (Qualcomm) or Pre-2022 (Exynos)?
Secondly: Perhaps try flashing with Odin and following the LineageOS guide for your respective device (Qualcomm/Exynos) rather than relying on the instructions from the LineageOS page.
Click to expand...
Click to collapse
İt is the old one with exynos.
I tried odin but odin does not seem like recognizing the device in download mode. I tried to flash recovery but it said “0/0” so basically it did nothing.
Edit: it seems like there is no dedicated exynos instructions for old ones.
Eldgrimr said:
Edit: it seems like there is no dedicated exynos instructions for old ones.
Click to expand...
Click to collapse
Instructions for Tab S6 Lite Exynos: https://forum.xda-developers.com/t/...for-galaxy-tab-s6-lite.4487553/#post-87376527
Thank you.
But this does not really help because I’m stuck in the loop and can’t boot into recovery. Therefore can’t do anything unless I get into recovery.
I need a way out of this loop.
Okay I figured it out.
Seems like tablet was soft-bricked due to messing up with bootloader.
I managed to get odin recognize the tablet by using directly motherboard usb ports and downloaded latest firmware from Sammobile. Then using odin, I re-flashed stock ROM and it came back alive.
Eldgrimr said:
Okay I figured it out.
Seems like tablet was soft-bricked due to messing up with bootloader.
I managed to get odin recognize the tablet by using directly motherboard usb ports and downloaded latest firmware from Sammobile. Then using odin, I re-flashed stock ROM and it came back alive.
Click to expand...
Click to collapse
Can you like, do a guide for me because I don't know how to do it
oakvx said:
Can you like, do a guide for me because I don't know how to do it
Click to expand...
Click to collapse
I am not able to do a step by step guie due to time but tablet had unlocked bootloader and somehow It got stuck on the boot loop.
So I downloaded lates system image from Sammobile, put the tablet in download mode, opened oden, connected tablet to PC via motherboard usb ports, odin recognized the tablet, then unzipped system image from sammobile and selected relevant (AP, BL etc.) files from odin. Then I flashed it using odin and tablet was now restored.
Eldgrimr said:
I am not able to do a step by step guie due to time but tablet had unlocked bootloader and somehow It got stuck on the boot loop.
So I downloaded lates system image from Sammobile, put the tablet in download mode, opened oden, connected tablet to PC via motherboard usb ports, odin recognized the tablet, then unzipped system image from sammobile and selected relevant (AP, BL etc.) files from odin. Then I flashed it using odin and tablet was now restored.
Click to expand...
Click to collapse
I'm sorry but what are motherboards port?
oakvx said:
I'm sorry but what are motherboards port?
Click to expand...
Click to collapse
USB ports behind the case. When you use the case USB ports on front or top it probably wont work for Odin
Eldgrimr said:
USB ports behind the case. When you use the case USB ports on front or top it probably wont work for Odin
Click to expand...
Click to collapse
Sorry to bother you bit where are them?
oakvx said:
Sorry to bother you bit where are them?
Click to expand...
Click to collapse
There should be around where you plug the ethernet cable in.
I got 2 usb 3.0 near the rj45 port
THANK YOU NOW IS IN DOWNLOAD MODE, from where did you get the firmware?

Categories

Resources