This is my first post on here, but I've used these forums before to root my S3 and at one time my current S4. My problem is with MF3... I used
this post [http://forum.xda-developers.com/showthread.php?t=2387577] to root my phone once, but since I couldn't install TWRP or CWM, I thought I could downgrade the software version with Odin. Well, I was wrong, and I unrooted my phone in the process... Upon trying the same technique I mentioned earlier, it now says "permission denied" upon entering the first prompt <<cd /mnt/extSdCard>>
AND, I can't use Odin to factory reset. Using posts such as this [http://www.youtube.com/watch?v=hZTTTk7vbVM] doesn't seem to work either. When putting my phone into download mode, I pull up Odin, and select the file in the link (the software file .tar I think), it says it fails shortly after starting.
Really, I need help with two things:
1. Obtaining root access
2. Resetting phone to factory settings
I might not have to do a factory reset, but I've noticed my wifi will NOT enable since I unrooted and this is a big concern for me. I know that all my troubles are because the bootloader is locked (and I'm messing with stuff I don't fully understand...), which is why I'd like help obtaining root again in the final hope that Safestrap [http://forum.xda-developers.com/showthread.php?t=2448925] is the answer I'm looking for so I can use my favorite ROM, LiquidSmooth!
PLEASE help me any way you can! I've tried to provide as much information as I can think of, but I'm new to this stuff, so bear with me. I have no real experience in rooting and whatnot, but so far, I've followed directions by users of this forum, so I have faith that there's a solution to this mayhem. Thanks for any help you can provide! =)
Your first mistake was not reading about what you can and can not do while on mf3. Your second was trying to put a recovery on. And your third was trying to use Odin to down grade your firmware.
I'm surprised your not having issues booting. The only way right now to get your phone back to normal is to see if best buy will flash the mf3 firmware for you
Edit, read this http://forum.xda-developers.com/showthread.php?p=45359306
jd1639 said:
Your first mistake was not reading about what you can and can not do while on mf3. Your second was trying to put a recovery on. And your third was trying to use Odin to down grade your firmware.
I'm surprised your not having issues booting. The only way right now to get your phone back to normal is to see if best buy will flash the mf3 firmware for you
Edit, read this http://forum.xda-developers.com/showthread.php?p=45359306
Click to expand...
Click to collapse
I guess you're trying to be helpful, but your condescending tone isn't helping. I READ everything, I just don't UNDERSTAND everything... The second paragraph actually provided some help, so thanks for that. I was just hoping for something I could do myself to re obtain root so that I can try the Safestrap method I provided in my original post. I will post a reply to the root method post and see if anyone can help me there, since that's my main issue is not being able to get root access back. I don't have any problems booting though, only when I boot into recovery mode do I get a loop in which I just have to get to the Samsung warning screen and select "cancel (reboot phone)". Thanks for reading this and providing some direction.
jeremythetree said:
I guess you're trying to be helpful, but your condescending tone isn't helping. I READ everything, I just don't UNDERSTAND everything... The second paragraph actually provided some help, so thanks for that. I was just hoping for something I could do myself to re obtain root so that I can try the Safestrap method I provided in my original post. I will post a reply to the root method post and see if anyone can help me there, since that's my main issue is not being able to get root access back. I don't have any problems booting though, only when I boot into recovery mode do I get a loop in which I just have to get to the Samsung warning screen and select "cancel (reboot phone)". Thanks for reading this and providing some direction.
Click to expand...
Click to collapse
No, your main issue is that you don't understand what you are reading and you shouldn't be doing anything to your phone until you do. Dozens of people just like you pass through this forum everyday with similar issues because they didn't read or take the time to understand what it was that they did read. Someone takes the time to tell them to read and learn and they don't listen or think they don't have to. Then, they screw their phones up and come back here crying for help. So it's not a condescending tone, it's people getting tired of the same crap. You admitted that you didn't understand everything you read so why would you do anything to your phone before you do understand it? Can you not see the problem?
Hey guys!
At first, this is my first post here so please be lenient if I posted this in the wrong section or whatever. I still need to get used to this forum.
Second, English is not my native language so it could become some gibberish from time to time. I also have to mention that my Android skills are somewhere between newbie and advanced, so please keep that in mind.
But let's get ahead to my problem:
Some days ago, I decided to install Linage OS 14 on my SM-N910F because I don't like the Stock Android 6.0.1 of it.
As you know, a custom ROM requires an unlocked bootloader an that's where my struggle starts.
I simply can't find any tutorial or similar for my phone. The only one I found didn't work (It was with adb fastboot, the process got stuck at "<wating for device>" after the command "fastboot unlock oem" which was described in the tutorial).
I retried it about three or four times before I gave up. It feels like I searched the entire internet, including this forum, but I couldn't find anything useful.
Maybe it's my fault because I didn't look properly, but yeah, know I'm here to ask directly:
Do you guys have any tricks, tipps, ideas or tutorials for me to try?
If it helps you, my phone is already rooted. (chainfire's CF Autoroot)
It'd make me really, really happy and already thank you for your (hopefully) incoming answers.
Vygravlil said:
Hey guys!
At first, this is my first post here so please be lenient if I posted this in the wrong section or whatever. I still need to get used to this forum.
Second, English is not my native language so it could become some gibberish from time to time. I also have to mention that my Android skills are somewhere between newbie and advanced, so please keep that in mind.
But let's get ahead to my problem:
Some days ago, I decided to install Linage OS 14 on my SM-N910F because I don't like the Stock Android 6.0.1 of it.
As you know, a custom ROM requires an unlocked bootloader an that's where my struggle starts.
I simply can't find any tutorial or similar for my phone. The only one I found didn't work (It was with adb fastboot, the process got stuck at "<wating for device>" after the command "fastboot unlock oem" which was described in the tutorial).
I retried it about three or four times before I gave up. It feels like I searched the entire internet, including this forum, but I couldn't find anything useful.
Maybe it's my fault because I didn't look properly, but yeah, know I'm here to ask directly:
Do you guys have any tricks, tipps, ideas or tutorials for me to try?
If it helps you, my phone is already rooted. (chainfire's CF Autoroot)
It'd make me really, really happy and already thank you for your (hopefully) incoming answers.
Click to expand...
Click to collapse
Pretty certain your bootloader isn't locked, you just need to install twrp with odin and then you are good to flash lineage
sawdoctor said:
Pretty certain your bootloader isn't locked, you just need to install twrp with odin and then you are good to flash lineage
Click to expand...
Click to collapse
Thank you for your fast reply. I'll try it once again, moreover I'll let you know if it worked.
It's me again. Flashing the ROM worked, my phone now runs under Linage OS 14.1. But now I've got another problem: Gapps. Somehow I can't flash the Gapps package, TWRP always tells me that the file is corrupted. I downloaded both the Pico and the Nano package for ARM Android 7.1* devices. Both don't work. I also tried the Android 7.0.* version, but that didn't work ofcourse. (Error 20: Wrong Android version installed on the device.) Is it my fault because I downloaded the wrong packages or what's the issue?
It'd be awesome if you could help me again.
Vygravlil
EDIT:
Okay, now it works. TWRP was right, the file was corrupted. I figured out that my PC kinda messed up the download of the package. I downloaded it with another computer and now everything works fine.
I have rooted countless phones accross all different manufacturers but never found one as stupid to root as this phone!
There isn't an up to date thread about rooting the phone so I thought I'd share how I did it and got through various things that were not supposed to happen but did!
Firstly, unlocking the Bootloader - as Huwai don't provide a code anymore, I went down the https://www.dc-unlocker.com/ route. It is cheap at £4 and they take PayPal. The unlock code video is out of date which didn't help and I presse3d the wrong button first and got a unlock network code by mistake, so had to pay another £4 to do it again. I used this tool (minimal adb) from this thread (https://forum.xda-developers.com/showthread.php?t=2317790) to put the code in the phone but noticed that my phone wouldn't keep the USB Debugging active and had to slide it on each time I connected to the computer (even had to revoke the computer at one point and reconnect).
From an unlocked bootloader the biggest problem I had was finding a way to put TWRP on the phone. All the threads I could see contained the wrong code to flash and so it always failed. However Dru79 showed the correct form which was to connect in fastboot then use minimal adb (on windows 10, open from the start menu, not left shict right click and 'open window here') and use " fastboot flash recovery_ramdisk TWRP-3.2.3-0-Hi6250-Askuccio-v1.0.img " - the correct TWRP is here (https://forum.xda-developers.com/p8.../recovery-twrp-3-2-3-0-huawei-hi6250-t3859959)
HOWEVER - my phone would not keep TWRP and more often (over 75% of the time) would boot to stock recovery, SO after I flashed the TWRP I typed in "fastboot reboot" and as I pressed ENTER, I took the power cord out from the phone and used the volume UP and the Power key to get into TWRP. I don't know why my phone wouldn't keep TWRP but it didn't.
Getting root through SuperSU was IMPOSSIBLE no matter how I tried, eventually I downloaded Magisk from (https://www.xda-developers.com/how-to-install-magisk/) and flashed it through TWRP.
Once rooted, I downloaded the PixyOS from https://forum.xda-developers.com/p8lite/p8-lite-2017-development/rom-pixysos-huawei-hi6250-t3852152 and flashed it...perfect!
Hope this helps someone.
The funny thing is, I actually wanted to post a thread about it in General Section as I had the same frustration as you whole trying to root and install custom ROM on this phone (I've done countless Root's, flashes, unlocking before on couple of phones) and just couldn't find a thread that explains this properly.
Anyway since you already done this, this should be moved to General Section so people can see this properly.
I've flashed Pixy's OS on my phone about 4 weeks ago and just one thing you didn't mention is that if you're on 7.1 nougat then you need to upgrade to Oreo and then install TWRP (I found that out when I tried getting it on nougat and then got errors while flashing and realised the TWRP was developed to work on Oreo). Just get a stock image of Oreo and flash it, the link for it it's somewhere around in the forum, I think it's some kind of Russian website but works well.
Anyway great job, if we can just ask Mod to move this to General section so that this guide can aid new users in rooting their phones properly and efficiently so that they can minimize their changes of encountering errors (as me and OP did).
proadi96 said:
The funny thing is, I actually wanted to post a thread about it in General Section as I had the same frustration as you whole trying to root and install custom ROM on this phone (I've done countless Root's, flashes, unlocking before on couple of phones) and just couldn't find a thread that explains this properly.
Anyway since you already done this, this should be moved to General Section so people can see this properly.
I've flashed Pixy's OS on my phone about 4 weeks ago and just one thing you didn't mention is that if you're on 7.1 nougat then you need to upgrade to Oreo and then install TWRP (I found that out when I tried getting it on nougat and then got errors while flashing and realised the TWRP was developed to work on Oreo). Just get a stock image of Oreo and flash it, the link for it it's somewhere around in the forum, I think it's some kind of Russian website but works well.
Anyway great job, if we can just ask Mod to move this to General section so that this guide can aid new users in rooting their phones properly and efficiently so that they can minimize their changes of encountering errors (as me and OP did).
Click to expand...
Click to collapse
I have asked
Dear and knowledgeable readers!
Being a longtime lurker, your tireless work and dedication to the community have enabled me to unlock and root many different android devices over the years and I am deeply grateful this place exists.
Right now, I plan on adding the recently released
Lenovo Smart Tab M10 FHD Plus 2nd Gen [ZA5T0302SE / TB-X606F, I believe]
in the WLAN/4GB/64GB variant to my collection. Having grown accustomed to the luxury of root access, I was wondering if anyone already had some experience with rooting the device and would be willing to share his / her knowledge with me.
Especially, I was wondering if this guide for the TB-X605F, which I have successfully used in the past for my older model, would (in principle) be applicable, as long as I could obtain the corresponding firmware for the newer one, which might be available here (as soon as GD wills it).
Any advice / support would be highly appreciated!
[Sidenote]: To my best ability, I wasn’t able to find an existing thread on the topic of rooting the device in question and I hope to have chosen the right forum to post it in (or if the general Q&A would have been the better fit?). If not, dear mods, please be lenient with me and simply move the thread to the proper subforum.
Brotinger said:
Dear and knowledgeable readers!
Being a longtime lurker, your tireless work and dedication to the community have enabled me to unlock and root many different android devices over the years and I am deeply grateful this place exists.
Right now, I plan on adding the recently released
Lenovo Smart Tab M10 FHD Plus 2nd Gen [ZA5T0302SE / TB-X606F, I believe]
in the WLAN/4GB/64GB variant to my collection. Having grown accustomed to the luxury of root access, I was wondering if anyone already had some experience with rooting the device and would be willing to share his / her knowledge with me.
Especially, I was wondering if this guide for the TB-X605F, which I have successfully used in the past for my older model, would (in principle) be applicable, as long as I could obtain the corresponding firmware for the newer one, which might be available here (as soon as GD wills it).
Any advice / support would be highly appreciated!
[Sidenote]: To my best ability, I wasn’t able to find an existing thread on the topic of rooting the device in question and I hope to have chosen the right forum to post it in (or if the general Q&A would have been the better fit?). If not, dear mods, please be lenient with me and simply move the thread to the proper subforum.
Click to expand...
Click to collapse
If you download the lmsa tool, plug in the tablet and go to recovery it will download the full stock firmware. Then you can find it c/program data/LMSA/downloads.
I did that then downloads magisk manager. Extract the boot.img from firmware and put in storage of tablet. Then used magisk manager and patch the boot.img it will tell where it is stored. Extract from tablet and put it in same folder as adb/fast boot. Then put tablet in fastboot and fastboot flash boot magisk-patched.img. then fastboot reboot. The will be rooted with magisk
I forgot. You must unlock bootloader to do this.
Dear 11mackey11,
thank you so very much for caring enough to share your knowledge with me!
So the guide I mentioned earlier is pretty much applicable for the newer model as well? What a relief!
I am also grateful for the hint on how to obtain the stock firmware. For all the dirty things I did to my devices in the past, it never became necessary to put the LMS-Assistant to use, but I will gladly change that now.
As soon as my device arrives, I will try to root it as you suggested and will report back how I fared.
Again, many thanks!
It took me some time to finally get to it … delivery problems with the device … busy work schedule …
… anyhow, I now took the leap and am happy to report that, thanks to your advice, I was able to add another rooted device to my ever-growing collection. “Worked like a charm”, as they use to say.
To repeat myself, I am very grateful for you taking the time to respond to my question and reassuring me that this was the path to follow.
Honestly, thanks!
Brotinger said:
It took me some time to finally get to it … delivery problems with the device … busy work schedule …
… anyhow, I now took the leap and am happy to report that, thanks to your advice, I was able to add another rooted device to my ever-growing collection. “Worked like a charm”, as they use to say.
To repeat myself, I am very grateful for you taking the time to respond to my question and reassuring me that this was the path to follow.
Honestly, thanks!
Click to expand...
Click to collapse
Hi. I just purchased the same tablet. I would appreciate it if you could write up a guide on this forum. It would be a help for everyone.
I'm not even sure how you unlock the bootloader on this thing!
Hi and congratulations on your purchase! The TB-606F is a solid device in my book.
Although I have by now rooted more than a dozen android devices and guess I have at least somewhat of an idea of what I am doing, I am by far no pro on the issue. Basically, I consider myself more a “guide user” than a “guide creator”, still.
But as I have benefited from the kind- and helpfulness of this community many times before, I can’t leave this call for help unanswered.
The thing is, nonetheless, I would really like to refer anyone poised to root their TB-606F to the guide for the TB-605F which I linked to in my initial post. Rooting the TB-606F, in principle, demands the user to undertake the same steps as for rooting the TB-605F.
There are, from the top of my head, only two noticeable differences or variations from that guide which I discovered:
1) firmware
As I still haven’t found a reliable source to obtain the necessary stock firmware by download from the web, the advice of fellow user 11mackey11 comes in very handy who, in response to my initial post, pointed me to the LSMA to download the firmware from your very own device.
2) unlocking bootloader
At least with my device, the fastboot commands known to me to usually unlock the bootloader (as are “fastboot oem unlock-go”, “fastboot oem unlock” or “fastboot flashing unlock”) did not do the trick. I had to resort to the command line of “fastboot flashing unlock” to finally make some progress. This might be an outlier with me device, though, as 11mackey11 did not mention the issue.
Again, I will gladly provide any assistance I can offer, but as for writing up a guide, I would mostly carbon copy turboperson123’s guide for the TB-605F mentioned above anyhow and it does not seem right to take credit for his contributions.
But if you had any specific question, please don’t hesitate to ask and I will answer it to my best knowledge (which might not be much).
Tutorial
I found this tutorial specific to the X606F https://forum.frandroid.com/topic/2...u-lenovo-tab-m10-fhd-plus-tb-x606f-sans-twrp/ alas in French but Google translate makes a decent job out of it
b4nd0ler0 said:
I found this tutorial specific to the X606F https://forum.frandroid.com/topic/2...u-lenovo-tab-m10-fhd-plus-tb-x606f-sans-twrp/ alas in French but Google translate makes a decent job out of it
Click to expand...
Click to collapse
I want to apply it to my device, have you tried this method?
Yes, tried and failed miserably. The tablet is not correctly rooted as reported by Root Checker. The su binary is there and shows it's Magisk but no root proper.
Will try again and report back when done.
b4nd0ler0 said:
Yes, tried and failed miserably. The tablet is not correctly rooted as reported by Root Checker. The su binary is there and shows it's Magisk but no root proper.
Will try again and report back when done.
Click to expand...
Click to collapse
thanks, I'm waiting for news from you. The tablet is sold very much in our country. like this in the world. I'm sure the developers will do something about this device.
b4nd0ler0 said:
I found this tutorial specific to the X606F https://forum.frandroid.com/topic/2...u-lenovo-tab-m10-fhd-plus-tb-x606f-sans-twrp/ alas in French but Google translate makes a decent job out of it
Click to expand...
Click to collapse
I rooted my device with this method
this method doesn't work
Hello dear Android users...
I've got the 3/64GB version of this device (ZA5T0300US) and this method of rooting did not work for me. When I check root in Magisk Manager, it says ctsProfile:false & basicIntegrity:true, so root doesn't work. I tried multiple times and every time had this same result. My ROM version is TB_X606F_USR_S100055_2001030016_V5.196_BMP_ROW (extracted ROM folder name). Are you sure your root actually 100% worked? What is your ROM version?
adroid_user said:
Hello dear Android users...
I've got the 3/64GB version of this device (ZA5T0300US) and this method of rooting did not work for me. When I check root in Magisk Manager, it says ctsProfile:false & basicIntegrity:true, so root doesn't work. I tried multiple times and every time had this same result. My ROM version is TB_X606F_USR_S100055_2001030016_V5.196_BMP_ROW (extracted ROM folder name). Are you sure your root actually 100% worked? What is your ROM version?
Click to expand...
Click to collapse
This method is working!
Use the Official Lenovo website to access your original "rom" file and get the "boot.img" file.
Program: Lenovo Rescue And Smart Assistant https://lnv.gy/3d8FHLi
For an article on how to download the Rom file via the program, see here. (Step 3)
https://bit.ly/2yE1nQf
Good Luck!
adroid_user said:
Hello dear Android users...
I've got the 3/64GB version of this device (ZA5T0300US) and this method of rooting did not work for me. When I check root in Magisk Manager, it says ctsProfile:false & basicIntegrity:true, so root doesn't work. I tried multiple times and every time had this same result. My ROM version is TB_X606F_USR_S100055_2001030016_V5.196_BMP_ROW (extracted ROM folder name). Are you sure your root actually 100% worked? What is your ROM version?
Click to expand...
Click to collapse
You did not enable Magisk Hide
mingkee said:
You did not enable Magisk Hide
Click to expand...
Click to collapse
That was it! Thanks! You're smarter & more helpful than Google!!! ))
Hi.
After i root the tablet, i tried to delete youtube and gdrive. Then i restart the tablet but it stuck in fastboot mode. Not booting.
i couldn't install stock rom. What i must do
I did this..
i patched the boot img from the lenovo program. and i like to shut down my devices when i dont use them and now i cant make it boot. im stuck in a bootloop and its says orange alert when i boot the device. i can only get into the fastboot menu. when i try to boot with vol + and power nothing happens and when i release it starts up again in a bootloop. i cant shut it down either. it just loops and loops. cant do the rescue thing with the program either.. anybody that knows how i can fix this?
I have an out of topic question regarding this tablet.
Can The Lenovo M10 Plus (2nd Gen) 10.3" TB-X606F Output Display via HDMI to TV ???
I tried using a powered USB-C to HDMI adapter to output/mirror the tablet to a TV, but it didn't work.
Brotinger said:
Hi and congratulations on your purchase! The TB-606F is a solid device in my book.
Although I have by now rooted more than a dozen android devices and guess I have at least somewhat of an idea of what I am doing, I am by far no pro on the issue. Basically, I consider myself more a “guide user” than a “guide creator”, still.
But as I have benefited from the kind- and helpfulness of this community many times before, I can’t leave this call for help unanswered.
The thing is, nonetheless, I would really like to refer anyone poised to root their TB-606F to the guide for the TB-605F which I linked to in my initial post. Rooting the TB-606F, in principle, demands the user to undertake the same steps as for rooting the TB-605F.
There are, from the top of my head, only two noticeable differences or variations from that guide which I discovered:
1) firmware
As I still haven’t found a reliable source to obtain the necessary stock firmware by download from the web, the advice of fellow user 11mackey11 comes in very handy who, in response to my initial post, pointed me to the LSMA to download the firmware from your very own device.
2) unlocking bootloader
At least with my device, the fastboot commands known to me to usually unlock the bootloader (as are “fastboot oem unlock-go”, “fastboot oem unlock” or “fastboot flashing unlock”) did not do the trick. I had to resort to the command line of “fastboot flashing unlock” to finally make some progress. This might be an outlier with me device, though, as 11mackey11 did not mention the issue.
Again, I will gladly provide any assistance I can offer, but as for writing up a guide, I would mostly carbon copy turboperson123’s guide for the TB-605F mentioned above anyhow and it does not seem right to take credit for his contributions.
But if you had any specific question, please don’t hesitate to ask and I will answer it to my best knowledge (which might not be much).
Click to expand...
Click to collapse
Hey, thanks for all this useful info. I'm a noob when it comes to rooting. I have hit an issue, that you guys could probably easily advice me. I have got up to where you enter "fastboot flashing unlock" it comes back with something like "waiting for any device". How do I get past this point? I have tried pressing volum up as I saw on a guide however no luck.
unlock not possible
CMX939 said:
Hey, thanks for all this useful info. I'm a noob when it comes to rooting. I have hit an issue, that you guys could probably easily advice me. I have got up to where you enter "fastboot flashing unlock" it comes back with something like "waiting for any device". How do I get past this point? I have tried pressing volum up as I saw on a guide however no luck.
Click to expand...
Click to collapse
I have the same issue, "waiting for device" and adb dies.
I assume, the latest lenovo updates (Android 9) block unlocking.
The current! LMSA tool does not allow to restore an old separately downloaded firmware
Hello! So this may be a long post, but I don't give a heck. Also, when I say hackers, I mean In a good way, like white hats. So, here is my first inquiry. How do people even find these exploits to put in the root binary? I've read articals about people intentionally crashing devices, which then puts it in a state vulnerable enough to bruteforce the binary in (At least that's what I thought...) I know that android is also based off of java, (Once again, an assumption) and I wonder where and how people get these ideas.
My second question is, As I haven't been able to find anything of this, aren't apps installed into portions of a phone where the normal user isnt able to touch on phones without root? Again, a newbie assumption.
So anyways, I am pretty interested in android development and rooting/custom code/bootloaders, and I'm not to keen on the subject.
I am also pretty bad at understand android right now, sooo, you can laugh at me if you want :silly:
Also I don't know if this is in the right thread
Alright, so I'm not sure about this, but I was thinking about what happened yesterday, and I thought about when I accidentally flashed the wrong CP file in Odin, and then when I tried to boot it, it gave me the "An error has occurred whilst the phone was updating. Please launch the Verizon Software Assistant". I also realized very quickly, that this is just the download screen without the extra information in the top right, and also realized that the download bar shows up also when you use Odin.
To give you my real question, I want to know if the Software Assistant uses any other method that isn't using Odin, and that if that is so, If you could maybe modify where it gets the flashing files to flash files onto the phone, without the phone realizing that they aren't official files?
To also be honest, I'm not an exploit finder, and maybe other people have thought of this, but eh, why not try and ask people about it? :good:
also I don't know if the phone itself will check those files....
also here is the zip with the Software Assistant.
Click here for the Assistant.