Hallo,
I got a Galaxy S4 (GT-I9505) from a friend of mine. He did'nt know, what happens. The phone became very hot, made vibration-Noise and was not able to start it anymor.
I also tried to start the phone, but it got a boot-Loop.
So I thought to reflash the phone.
I am able to start the Download-Menü (Vol - + Power + HOME). The Recovery-Menü did not start finally. It hang.
So first I wanted to put an original Samsung-ROM to the Phone. But where can I get the right one?
On the sticker in under the accu is written:
Model: GT-I9505SSN: -I9505GSMH
When I start the Download-Modus and connect it with ODIN, I can read the following:
ODIN MODE
Product Name: GT-I9505
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0KNOX WARRANTY LOCK: 0x0
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE enable
I searched this forum and the net, but I did'nt get a Firmware-Image, the I was able to flash finally with ODIN to the phone.
I start ODIN with ADMIN-Rights and the KIES-App is deletet from the processes. The Samsung-USB-drivers are installed and the phone was found in ODIN.
Could anybody of You give me a way-sign where I have to read the solution of the problem? Or could anybody of you explain the process of flashing?
THanks a lot for your help.
with best regards
speedy8 said:
I searched this forum and the net, but I did'nt get a Firmware-Image, the I was able to flash finally with ODIN to the phone.
Click to expand...
Click to collapse
Sammobile.com for the firmware. Unzip the firmware, select "AP" in Odin, and point to the extracted tar.gz image. Odin should then flash the image.
Related
hi there im new to these forums and have serched everwhere for a solutuion but i cant find one anywhere. I recently tried to put a custom rom on, but now when i try to turn my phone on it says: Firmware upgrade encountered an issue. Please select recovery ode in kies & try again. Kies wont reconise my device as it wont fully turn on and when i try flash the stock firmware to my device using odin, on the download screen on my phone it doesnt download it from odin it has this on the screen under download mode:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X1
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION: ENABLED
eMMC BURST MODE enabled
Please help?!
- Download and install this drivers -> HERE
- Put ur phone in DOWNLOAD MODE (how u had it before)
- Install ODIN in ur pc -> How to
- Flash ur STOCK FIRMWARE (it comes with .zip file, u have to unzip it and use only the .tar file)
- Enjoy ur phone again
At first, sorry for my english, i'm french...
Well, everything is in the title.
I am the owner of a Galaxy Tab4, WiFi, 16GB, SM-T530 model.
I wanted to root it, then install TWRP and a custom rom.
Via Odin, I install the TWRP recovery(2.8).
After I started the flash of a Omnirom. Everything went normally, but on reboot, I have the Samsung Galaxy Tab logo 4 well, but in the upper left corner marked,:
KERNEL IS NOT SEANDROID enforcing (in red)
Set Bit Warranty: kernel (yellow)
If I start in download mode, I have written:
ODIN MODE
PRODUCT NAME: SM-T530
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX WARRANTY VOID: 0x1 (4)
QUALCOMM SECUREBOOT: ENABLE (CBS)
SWREV RP: S1, T1, R1, A1, P1
UDC START
2 days ago, I traveled all the forums, downloaded everything I could find, flash all of things, makes "format data" wipe everything, etc .....
I can not go through Odin because it is no longer recognized.
Nothing works
It's awful, if someone can help me..........
Are you sure you're not able to get into download mode with pressing Volume Down + Home Button + Power Button? It should work if you press them until download mode appears.
Its for testing only. Havent read? But you should be able to go in download mode
Download stock rom, boot into download mode, flash stock Rom.
1019
Hi,
is there someone who can edit my post, I've solved my problem, and then want to put my thread in "solved".
I found a stock rom, then, with Odin, went threw every step.
my tab found a new life.
Thanks to all of you.
latriche said:
Hi,
is there someone who can edit my post, I've solved my problem, and then want to put my thread in "solved".
I found a stock rom, then, with Odin, went threw every step.
my tab found a new life.
Thanks to all of you.
Click to expand...
Click to collapse
Could you tell me exactly how you did it I have a galaxy tab 4 and its saying the same thing I used sammobile firmware but when I try to flash it fails after nand start
Dear XDA User,
I get bootloop after flashing stock firmware via ODIN, from Thread [GUIDE] Unroot/Unbrick, Flash stock Firmware i9505 I've try many way, but my i9505 still bootlop after Samsung Logo and vibrate.
I can't enter recovery mode, but when I enter Downloading Mode, here the status:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE enabled
I've try ODIN with PIT File to, but still get bootloop, Please help me, this is my only cellular phone.
* Sorry for my bad English
Did you do a factory reset in recovery?
GDReaper said:
Did you do a factory reset in recovery?
Click to expand...
Click to collapse
I can't enter Recovery mode, it's always bootloop, after flash custom recovery like TWRP, it's still same, just Downloading mode that I can enter...
Open Odin, uncheck everything except f reset time, flash rom, when you see the reset in the status window, remove USB cable from the phone, remove battery, replace battery, use buttons to boot into recovery (power, home, volume up) wipe, and reboot.
Please Help me I don't Know the right FIRMWARE For this device. Here's an Information that I saw in my device. I'm really Confused what ROM to download. I used Safestrap App and Wipe My Device and It turns out Stuck at Samsung Logo with a picture of Padlock (that is Unlocked) and below the padlock it says "Custom". All I Can do is to go to DOWNLOAD MODE. I hope someone can Help or Give me Information. TIA
1.) When I try to update the software, my screen goes to AT&T Update screen, So I think it's an AT&T Device.
2.) When I go to DOWNLOAD MODE, Here's what I see:
Odin Mode.
SGH-I337
Binary: Samsung Official
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x0
CSB-Config-LSB: 0x30
Write protection: enable
eMMC burst mode enabled
3.) Please See these Attachment Pictures (I use Sammobile App to Identify my device Info.)
Your device is what download mode says.
The pad lock screen is only on the AT&T s4 which is the sgh-i337. The phone has a locked bootloader and can only run custom ROMs that can be flashed using safestrap. You will need to re-flash the stock firmware.
This may help: https://forum.xda-developers.com/ga...-to-update-to-i337oc3-5-0-1-keeproot-t3075814
Hi all,
Please bear with me, I'm in way over my head here and don't understand most of what I've done. I was experimenting when I probably shouldn't have been.
So, I installed DarkLord's Note 7 kernel and rom. I found it to be quite buggy and am now wanting to wipe my phone and install Phronesis-N9005-N7-v6.0.
Problem is, when trying to boot into TWRP, I'm met with the the following:
ODIN MODE
Product name: SM-N9005
Current binary: Custom
System status: Official
Reactivation lock(kk): Off
Knox Kernel lock: 0x0
Knox warranty void: 0x1
Qualcomm secureboot: Enable (csb)
Rp swrev: S2, T2, R2, A3, P3
Write protection: Enable
UDC start
Downloading...
Do not turn off target
I've had it on for hours and it didn't do anything.
I managed to reboot it and it ran as it did before, in Darklords rom.
I read I have to install the official firmware and install it via Odin but I can't find anything about my device. On the back of it, it says:
SM N9005
FCC ID - A3LSMN9005
SNN - N9005GSMH
When I enter it into sammobile, nothing comes up.
Have I got this wrong? Should I be looking for something else?
You are booting to download mode not recovery .
Boot to recovery TWRP
#N9005 model firmware are on sammobile etc.
https://forum.xda-developers.com/galaxy-note-3/general/samsung-galaxy-note-3-sticky-roll-t3237249
Booting into recovery via TWRP manager just results in the same Odin screen for me
As for the firmware - I'm not really sure which region I should pick out of those. I just thought this was an international model, but then I downloaded an app called Phone INFO and it tells me it's Vietnam. Could this be because of the rom already on there? It does also say it's a Note 7, so I'm assuming it's incorrect.
TWRP manager
DO NOT USE just boot to recovery via the vol up home and power buttons as normal .
Copy Phronesis to ext sd card and flash as per instructions .
You have N9005 Pick your area /network where you are .
Phone Info can only go by what's on your phone and you flashed DarkLord's Note 7 firmware .
Booting via manager was a last resort. I was trying the usual way and it also resulting in the same thing.
Boot to download/ Odin mode flash stock rom .
Thanks JJEgan, I figured out how to use Odin3 and Odin mode, then install Phronesis. All is good now