UPDATE - Pixel Experience Official is out for Kenzo. Link attached below. Ongoing support for GSI users though.
https://forum.xda-developers.com/redmi-note-3/development/rom-pixel-experience-t3835648
-------------------------------------------
Disclaimer: I'm not responsible for bricked devices, flash at your own risk. I might be able to help with restoring your device though.
This is a guide to installing Android GSI on Redmi Note 3 (Kenzo)
---------------------------------------------------
What works-
RIL
GPS
Camera
Pretty much everything
What doesn't work-
Bluetooth
Hotspot
VoLTE(I couldn't test)
(NOTE - Bugs vary GSI to GSI)
---------------------------------------------------
Required files -
Grab these files first, and keep them on your SD card
TWRP Treble - https://androidfilehost.com/?fid=5862345805528059847
Android GSI(USE ARM64 A-ONLY) - for this tutorial, I'm using Phhusson's AOSP Pie GSI found here - https://forum.xda-developers.com/pr...vice-development/aosp-9-0-phh-treble-t3831915
List of GSI's - https://github.com/phhusson/treble_experimentations/wiki/Generic-System-Image-(GSI)-list
Pie GApps (If using Pie GSI) - https://forum.xda-developers.com/android/development/gapps-unofficial-opengapps-builds-t3828141
Vendor Image - https://androidfilehost.com/?fid=1322778262903993757
Permissive SELinux Enabler - https://drive.google.com/file/d/1KFdPH2JGtvkXwt2emxPb-k7zdv2pLd-F/view?usp=drivesdk
Magisk 16.7 (minimum 16.7, you can use 17 as well)- https://forum.xda-developers.com/apps/magisk/beta-magisk-v13-0-0980cb6-t3618589
Latest Firmware - https://forum.xda-developers.com/redmi-note-3/development/firmware-hmnote3proglobal-t3574361/page176
Optional - Digital Well-being (ONLY FOR PIE)
Digital Well-being apk (Download latest version) - https://www.apkmirror.com/apk/googl...wellbeing-0-2-207862754-android-apk-download/
Digital Well-being Magisk Module - https://drive.google.com/file/d/1AAFMWbAAK-febiP9h4iZMJONEHXopmEU/view?usp=drivesdk
--------------------------------------------
Assuming you have an unlocked bootloader, and know your way in and around Android, let's begin!
How to install -
1. First, flash the Treble enabled TWRP.
2. Reboot to recovery.
3. Mount all partitions, and wipe all partitions.
4. Flash the Vendor Image zip file and immediately flash the Permissive SELinux Enabler.
5. Clear Dalvik/Cache.
6. Mount all partitions, and wipe system.
7. Flash GSI to System partition *only*.
8. Reboot to System.
9. Reboot to recovery.
10. Perform a factory data reset, and flash GApps
11. Reboot to System, and complete setup.
12. After completing setup, reboot to recovery and flash Magisk 16.7
13. Reboot to System
14 Reboot to recovery and flash firmware.
15. Profit!
If you want Digital Well-being (ONLY FOR PIE) -
16. Install Digital Well-being apk
17. Flash Digital Well-being Magisk Module through Magisk Manager
18. Reboot
19. Profit!
-------------------------------------------------------
Tested on Snapdragon version, don't know if it works on MTK.
Screenshots are attached.
Fixes -
If you have the QS toggles moving out of the header like the screenshot attached in #1, do the following steps
1. Enable Developer Settings,
2. Find Smallest Width setting
3. Increase the value by 20. (If it's 360, make it 380)
4. Profit!
------------------------------------------
Google Camera + Face Unlock fix.
If Google Camera/Face Unlock doesn't work for you, do the following -
1. Reboot to recovery
2. Mount system
3. Flash the zip file (download link below)
4. Clear cache
5. Reboot to system
This should make Face Unlock work again, and GCam work as well.
Download patch - https://drive.google.com/file/d/17OUBxhsfeK0625_pYe8aRNr5L6doKdAK/view?usp=drivesdk
------------------------------------------
Can't find Smart Lock in settings?
1. Go to Settings < Security and Location.
2. Scroll down and click Advanced.
3. Click Trust Agents.
4. Switch on Trust Agent for Smart Lock.
You should now have Smart Lock option below Fingerprint.
-------------------++++++++++++++++-----------------------
For Changing accent colours -
Download this file - https://t.me/kenzousersglobal/1169
1. Flash it in recovery
2. Reboot to system
3. Go to Settings - Display - Advanced. Scroll down to find "Colour Theme"
4. Select colour theme and select colour of your choice.
5. Profit!
---------------------------------
Custom kernels that currently work
Radon - https://drive.google.com/file/d/1LYggpHDVph1fvWctIKY4FqQwtRb6Svh0/view
---------------------------------
Review - after extensive testing, I found this to be daily driver material, with the only exception being Bluetooth, Hotspot, and VoLTE(I couldn't test it myself)
Special thanks to - @corkiejp
Is it possible to get an Overlay Patch for Mi 8?
NielsvdS said:
Is it possible to get an Overlay Patch for Mi 8?
Click to expand...
Click to collapse
I honestly have no clue. I have only gathered all the patches and files for Kenzo and made them into one guide.
Thanks for the guide: -
Digital Well-being apk (Download latest version) <<<< Links to the overlay zip and not the apk.
Sourced the beta of apkmirror: - https://www.apkmirror.com/apk/googl...wellbeing-0-2-207862754-android-apk-download/
I used Mind the Gapps found on Telegram, when flashing.
Is it possible to dirty flash open gapps?
Work on kate devices?
Why is it there system.img.xz should I remove .xz rename it
---------- Post added at 04:24 PM ---------- Previous post was at 03:42 PM ----------
1.flashed carlosvendor.zip
2.mounted system vendor cache
3.flshed system.img as system image
After rebooting stuck at fastboot logo
sharan565 said:
Why is it there system.img.xz should I remove .xz rename it
---------- Post added at 04:24 PM ---------- Previous post was at 03:42 PM ----------
1.flashed carlosvendor.zip
2.mounted system vendor cache
3.flshed system.img as system image
After rebooting stuck at fastboot logo
Click to expand...
Click to collapse
You need to extract the image file from that compressed format, use windows are download an app that will extract it.
Suggestion RAR from play: - com.rarlab.rar or alternative app that will do the same.
corkiejp said:
You need to extract the image file from that compressed format, use windows are download an app that will extract it.
Suggestion RAR from play: - com.rarlab.rar or alternative app that will do the same.
Click to expand...
Click to collapse
Thanks man I will try
Hey @Sid127, this is really nicely written tutorial, thank you What bothers me, why we need to mount partitions once again in step 6? Partitions were mounted in step 3 and there wasn't any reboot in meanwhile.
3. Mount all partitions, and wipe all partitions.
4. Flash the Vendor Image zip file.
5. Clear Dalvik/Cache.
6. Mount all partitions, and wipe system.
7. Flash GSI to System partition *only*.
Click to expand...
Click to collapse
Second question, maybe easier... If I have existing TWRP backup for non treble ROM, is it OK to restore such backup using Treble recovery after wiping everything? Or it's recommended to flash previous recovery first?
wxtester said:
Hey @Sid127, this is really nicely written tutorial, thank you What bothers me, why we need to mount partitions once again in step 6? Partitions were mounted in step 3 and there wasn't any reboot in meanwhile.
Second question, maybe easier... If I have existing TWRP backup for non treble ROM, is it OK to restore such backup using Treble recovery after wiping everything? Or it's recommended to flash previous recovery first?
Click to expand...
Click to collapse
1. You just need to make sure that all partitions are mounted.
2. You can restore the backup through Treble TWRP.
Happy flashing!
Hexvessel1992 said:
Work on kate devices?
Click to expand...
Click to collapse
I don't know, I need someone to test it. It should work, since the Vendor for Kenzo and Kate are the same.
corkiejp said:
Thanks for the guide: -
Digital Well-being apk (Download latest version) <<<< Links to the overlay zip and not the apk.
Sourced the beta of apkmirror: - https://www.apkmirror.com/apk/googl...wellbeing-0-2-207862754-android-apk-download/
I used Mind the Gapps found on Telegram, when flashing.
Is it possible to dirty flash open gapps?
Click to expand...
Click to collapse
I'll update the thread with the right link
I think it is possible to dirty flash Open Gapps, but it might give bugs, always go for a clean flash
Everything works for me, only thing was that at the first setup it was stuck on "checking for updates". So I tried the method of tapping all sides of the screen (from top-left clockwise to bottom-left) and it skipped the setup. The flashlight is a little wonky, but that's the only thing that was getting in my way. The audio was a little too quiet, so I installed some app on the playstore to gain it. Thanks for such a comprehensive guide! Android Pie is amazing, but development for it on a 3 year old device is even more so!
srishant said:
Everything works for me, only thing was that at the first setup it was stuck on "checking for updates". So I tried the method of tapping all sides of the screen (from top-left clockwise to bottom-left) and it skipped the setup. The flashlight is a little wonky, but that's the only thing that was getting in my way. The audio was a little too quiet, so I installed some app on the playstore to gain it. Thanks for such a comprehensive guide! Android Pie is amazing, but development for it on a 3 year old device is even more so!
Click to expand...
Click to collapse
I had to forage through 4 complex guides, scourge through XDA and Telegram for all the patches, and hence could make such a simple guide. Apparently, devs on the Telegram channel are working on the Bluetooth and VoLTE fix I'll update once that happens!
Bolte
Test n let me know if it works
https://t.me/kenzoromnews/1445
Modify for treble then flash
amog787 said:
Bolte
Test n let me know if it works
https://t.me/kenzoromnews/1445
Modify for treble then flash
Click to expand...
Click to collapse
I did see that, but when I flashed it, it messed upy system and I had to reinstall the GSI. I don't know how to modify it for Treble, could you do it? I'm happy to test. I believe that fix is for Flashavle ZIPs, not for Treble GSIs.
Possible Gcam and stock working patch!
Posted this in AOSP Pie Rom thread, may also work for the GSI?
corkiejp said:
I found Gcam Pie Fix for another device in this thread.
Link to Gcam Pie Fix: - https://drive.google.com/file/d/1D5qvlA-QbQu6xoWpsLPyWquMkS3hxXi3/view
Gcam that I'm using: - https://androidfilehost.com/?fid=673956719939833577
^^^ From this thread, maybe newer versions available.
I was able to setup face unlock after flashing the above fix, you may also need to enable Smart Lock (Google) as a trusted agent.
It is buggy and the face option may not always trigger, plus you need to hold the phone far from you and swipe when the lock symbol appears (no fast unlock options xposed).
Another benefit of flashing another Camera (V 2.0.002) Started working as well. (Don't know if that is the default AOSP camera or something I restored from backup? Could be Snap Camera from LOS).
Click to expand...
Click to collapse
corkiejp said:
Posted this in AOSP Pie Rom thread, may also work for the GSI?
Click to expand...
Click to collapse
Is there also an uninstaller for this fix? I'll test only if there is an uninstaller for it. Last time I tested a fix I had to format data to revert...
Sid127 said:
Is there also an uninstaller for this fix? I'll test only if there is an uninstaller for it. Last time I tested a fix I had to format data to revert...
Click to expand...
Click to collapse
Not that I'm aware of, but this just places/replaces some Lib and Lib64 in system partition.
If your worried about it, back up your system partition, flash the this patch and wipe caches.
If you experience problems, just restore your system partition.
It was reported working by someone else here.
YOUR WARRANTY IS NOW VOID! I am not responsible for anything that could happen, dead sd card, bricked phones, you name it. You chose to install this software and you face the risk of any bugs that may affect you. This is just a warning incase anything goes wrong
ISSUE: FASTBOOT Might not work on windows 10 version 2004, a solution is to use a Linux virtual machine to use fastboot commands. Test it out first as you might be lucky and it could work for you.
A complete guide on how to either just root the razer phone 2 and/or install a gsi with everything working.
The sections are: Basics - Installing TWRP - Rooting - Installing a GSI + Root - Passing safety net to use baking apps, certain games etc.
Basics: (You will have to factory reset if you have not unlocked your bootloader before)
Download this and this file, un zip them both and move them to a known directory such as C:\ADB
Then on your phone, go into developer options and enable OEM/Bootloader unlocking, and after that reboot into the bootloader by holding POWER + VOL DOWN and plug the phone into your pc (I recommend you connect it to a USB 2.0 port, as USB 3.0 might give you issues with the fastboot commands)
Then we need to install bootloader drivers onto our phone, so open device manager, click the drop down menu next to Android Device, right click on Android and select Update Driver, then select Browse my computer for driver software, Let me pick from a list of available drivers on my computer, Show all devices, Have disk and navigate to your folder where you extracted the .zips (in my case C:\ADB) and open the usb_driver folder and select android_winusb.inf. In the next menu select Android Bootloader Interface, proceed through the warning and install it.
To unlock the bootloader open a cmd window in the directory of your platform-tools folder, which in my case would be C:\ADB\platform-tools (type cd C:\ADB\platform-tools in cmd) and run two commands: fastboot flashing unlock (after each one select yes on your phone and let it reboot - it might take a while) and fastboot flashing unlock_critical
To install the arter97 kernel/TWRP: (keep your phone in the Bootloader and plugged into the pc)
Download both the .zip and .img file from this link (i am using r12 intentionally as it causes less issues) and download this zip file as well
Move both .zip files onto your phones SD CARD (important) and rename the .img file on your PC to Boot.img and place it into your platform-tools folder (C:\ADB\platform-tools in my case)
Open a command prompt window and like before change the directory to the platform-tools folder, then run two commands: fastboot flash boot_a boot.img and fastboot flash boot_b boot.img
Now using the volume keys select the Recovery Mode option in the bootloader and press the power key to select it, if it asks for a decryption password cancel it, and if it asks to allow system modifications swipe to allow it
Go to the Install section and navigate to external_sd and navigate to the arter-r12.zip you installed, then click it and swipe to flash, after that flash the f2fs zip and after it's complete back out to the main menu, click reboot and select recovery
Once you are back in recovery, go to Wipe and select Format Data (this will not erase your sd card if it is set as external storage) and type yes
If you don't want to root then to reboot to system go into Reboot and select System, TWRP will ask you if you want to install their special app, DO NOT INSTALL IT, CLICK ON DO NOT INSTALL.
Now you are ready to proceed to the next step(s) (these are short now don't worry)
To just root and stay on the stock ROM:
Download magisk 20.1 (works better) from here and move it onto your phone sd card by going to the main TWRP menu, selecting Mount then SD card and you should be able to transfer the file onto the sd card directly from your PC
Then simply flash the magisk 20.1 zip in TWRP as we did before and you can now reboot system (make sure to not install the TWRP app)
Magisk Manager will prompt you to update magisk, DONT do it. You can however install the latest magisk manager update
To install a GSI and Root: (lineageOS is what i have linked here, however this is not the only one you can use, make sure you NEED gapps before flashing it incase they are included anywhere)
Firstly, to have bluetooth working go to Mount and select Vendor, go back, select Advanced then File Manager then navigate to /vendor/overlay/ and delete both BluetoothResCommon.apk and RazerAuraBluetoothRes.apk
Then download the latest arm-64-bvN .img file from here, unzip it on your computer and move the .img file to your phone. If you also want gapps (google apps) download this file and move it onto your SD card as well
Now, head to the TWRP Install section, at the bottom select Install Image, select the downloaded lineageOS (or your own gsi) .img file, in the next screen select System Image and swipe to flash it.
Once it has flashed back out to the main screen and click on Wipe, then select Advanced Wipe, then select System, Repair or change file system, and finally press Resize and swipe to do it, if it fails then re do this step
Then go back into the Install section and flash the opengapps zip file and after that the magisk zip file
Now you can reboot to system (might take a couple minutes) and set up the phone.
If you notice it is running slowly go into settings > Phh treble settings (might have to force close app once for it to appear) > Misc Settings > Force FPS > and select the 120.00001 at the bottom (top numbers are 1080p and bottom numbers are 1440p)
Finally, to pass safetynet:
Head into magisk manager, go to its settings and enable Hide Magisk, then call it Manager and allow it to reinstall itself, after that enable Magisk Hide in the settings aswell (hide your banking apps with this or any game that wont boot due to ROOT)
Then go into the magisk downloads section and search for the ArCore module, install this, reboot and your safetynet will pass on a gsi
This is my first xda post so my formatting may be bad but i hope it can help some people if you have any questions drop a comment and please like the post if it helped you for more people to see it.
Have a good day
Usyless said:
YOUR WARRANTY IS NOW VOID! I am not responsible for anything that could happen, dead sd card, bricked phones, you name it. You chose to install this software and you face the risk of any bugs that may affect you. This is just a warning incase anything goes wrong
A complete guide on how to either just root the razer phone 2 and/or install a gsi with everything working.
The sections are: Basics - Installing TWRP - Rooting - Installing a GSI + Root - Passing safety net to use baking apps, certain games etc.
Basics: (You will have to factory reset if you have not unlocked your bootloader before)
Download this and this file, un zip them both and move them to a known directory such as C:\ADB
Then on your phone, go into developer options and enable OEM/Bootloader unlocking, and after that reboot into the bootloader by holding POWER + VOL DOWN and plug the phone into your pc (I recommend you connect it to a USB 2.0 port)
Then we need to install bootloader drivers onto our phone, so open device manager, click the drop down menu next to Android Device, right click on Android and select Update Driver, then select Browse my computer for driver software, Let me pick from a list of available drivers on my computer, Show all devices, Have disk and navigate to your folder where you extracted the .zips (in my case C:\ADB) and open the usb_driver folder and select android_winusb.inf. In the next menu select Android Bootloader Interface, proceed through the warning and install it.
To unlock the bootloader open a cmd window in the directory of your platform-tools folder, which in my case would be C:\ADB\platform-tools (type cd C:\ADB\platform-tools in cmd) and run two commands: fastboot flashing unlock (after each one select yes on your phone and let it reboot - it might take a while) and fastboot flashing unlock_critical
To install the arter97 kernel/TWRP: (keep your phone in the Bootloader and plugged into the pc)
Download both the .zip and .img file from this link (i am using r12 intentionally as it causes less issues) and download this zip file as well
Move both .zip files onto your phones SD CARD (important) and rename the .img file on your PC to Boot.img and place it into your platform-tools folder (C:\ADB\platform-tools in my case)
Open a command prompt window and like before change the directory to the platform-tools folder, then run two commands: fastboot flash boot_a boot.img and fastboot flash boot_b boot.img
Now using the volume keys select the Recovery Mode option in the bootloader and press the power key to select it, if it asks for a decryption password cancel it, and if it asks to allow system modifications swipe to allow it
Go to the Install section and navigate to external_sd and navigate to the arter-r12.zip you installed, then click it and swipe to flash, after that flash the f2fs zip and after it's complete back out to the main menu, click reboot and select recovery
Once you are back in recovery, go to Wipe and select Format Data (this will not erase your sd card if it is set as external storage) and type yes
If you don't want to root then to reboot to system go into Reboot and select System, TWRP will ask you if you want to install their special app, DO NOT INSTALL IT, CLICK ON DO NOT INSTALL.
Now you are ready to proceed to the next step(s) (these are short now don't worry)
To just root and stay on the stock ROM:
Download magisk 20.1 (works better) from here and move it onto your phone sd card by going to the main TWRP menu, selecting Mount then SD card and you should be able to transfer the file onto the sd card directly from your PC
Then simply flash the magisk 20.1 zip in TWRP as we did before and you can now reboot system (make sure to not install the TWRP app)
Magisk Manager will prompt you to update magisk, DONT do it. You can however install the latest magisk manager update
To install a GSI and Root: (lineageOS is what i have linked here, however this is not the only one you can use, make sure you NEED gapps before flashing it incase they are included anywhere)
Firstly, to have bluetooth working go to Mount and select Vendor, go back, select Advanced then File Manager then navigate to /vendor/overlay/ and delete both BluetoothResCommon.apk and RazerAuraBluetoothRes.apk
Then download the latest arm-64-bvN .img file from here, unzip it on your computer and move the .img file to your phone. If you also want gapps (google apps) download this file and move it onto your SD card as well
Now, head to the TWRP Install section, at the bottom select Install Image, select the downloaded lineageOS (or your own gsi) .img file, in the next screen select System Image and swipe to flash it.
Once it has flashed back out to the main screen and click on Wipe, then select Advanced Wipe, then select System, Repair or change file system, and finally press Resize and swipe to do it, if it fails then re do this step
Then go back into the Install section and flash the opengapps zip file and after that the magisk zip file
Now you can reboot to system (might take a couple minutes) and set up the phone.
If you notice it is running slowly go into settings > Phh treble settings (might have to force close app once for it to appear) > Misc Settings > Force FPS > and select the 120.00001 at the bottom (top numbers are 1080p and bottom numbers are 1440p)
Finally, to pass safetynet:
Head into magisk manager, go to its settings and enable Hide Magisk, then call it Manager and allow it to reinstall itself, after that enable Magisk Hide in the settings aswell (hide your banking apps with this or any game that wont boot due to ROOT)
Then go into the magisk downloads section and search for the ArCore module, install this, reboot and your safetynet will pass on a gsi
This is my first xda post so my formatting may be bad but i hope it can help some people if you have any questions drop a comment and please like the post if it helped you for more people to see it.
Have a good day
Click to expand...
Click to collapse
Thank you excellent post just what I needed.
eedwin101 said:
Thank you excellent post just what I needed.
Click to expand...
Click to collapse
I'm glad it helped you
Usyless said:
I'm glad it helped you
Click to expand...
Click to collapse
If you don't mind what other GSI ROMs have you tried that worked well with this phone I am particularly interested in the Google pixel Android 11. Thanks again you have extended the life of this phone for me.
eedwin101 said:
If you don't mind what other GSI ROMs have you tried that worked well with this phone I am particularly interested in the Google pixel Android 11. Thanks again you have extended the life of this phone for me.
Click to expand...
Click to collapse
I know that phhussons AOSP works on this phone with no issues aswell, you might have to use securize to get safety net to pass tho.
android 11 will boot on this phone however iirc you won't be able to hear and other people won't hear you in phone calls.
havoc gsis I believe works but I haven't tested it and I have only heard of one person using it.
BLISS/LOSQ/CAOS don't work on this phone at all.
and after that I don't think there really is many more GSIs that work as they just won't boot for bizarre reasons
How about text messaging. Currently i have not been able to get SMS to work with any GSI on Android 10. Are you able to send and receive text messages? Did you have to do anything to get it working? If so, let me know because i have been having a heck of a time with it.
_Sherrif said:
How about text messaging. Currently i have not been able to get SMS to work with any GSI on Android 10. Are you able to send and receive text messages? Did you have to do anything to get it working? If so, let me know because i have been having a heck of a time with it.
Click to expand...
Click to collapse
oh this issue... are you on T-Mobile by any chance as if you are there is no fix yet and you will have to wait for official lineageOS.
I am on three (UK) and everything works perfectly.
Usyless said:
oh this issue... are you on T-Mobile by any chance as if you are there is no fix yet and you will have to wait for official lineageOS.
I am on three (UK) and everything works perfectly.
Click to expand...
Click to collapse
No AT&T.
_Sherrif said:
No AT&T.
Click to expand...
Click to collapse
you might be able to use this fix (it's a magisk module) as it is made for AT&T https://t.me/razer_phone/14202
its called a volte fix but it should help with sms, if it doesn't work you can just remove the module, reboot then delete some qualcomm.ims app (should be shown in your app list)
_Sherrif said:
No AT&T.
Click to expand...
Click to collapse
or you could try this: https://t.me/razer_phone/12949
install instructions shown in the message
Usyless said:
you might be able to use this fix (it's a magisk module) as it is made for AT&T https://t.me/razer_phone/14202
its called a volte fix but it should help with sms, if it doesn't work you can just remove the module, reboot then delete some qualcomm.ims app (should be shown in your app list)
Click to expand...
Click to collapse
Aight! Definitely worth a try. Tried everything else.
Thank you!
Thanks!! Excellente guide, very important your note : "I recommend you connect it to a USB 2.0 port", with usb 3 doesn't work bootloader commands.
frannet said:
Thanks!! Excellente guide, very important your note : "I recommend you connect it to a USB 2.0 port", with usb 3 doesn't work bootloader commands.
Click to expand...
Click to collapse
Thanks
It doesn't necessarily not work with usb 3.0, for some people (and for me) it works with a usb 3.0 port however for a lot of people they have issues with it.
I will add it tho.
Usyless said:
Thanks
It doesn't necessarily not work with usb 3.0, for some people (and for me) it works with a usb 3.0 port however for a lot of people they have issues with it.
I will add it tho.
Click to expand...
Click to collapse
It's strange. With my razer blade it has not worked (usb 3) but with a Dell Precision with a one port usb 2, work fine. I was going crazy.
frannet said:
It's strange. With my razer blade it has not worked (usb 3) but with a Dell Precision with a one port usb 2, work fine. I was going crazy.
Click to expand...
Click to collapse
Yeah I remember I helped somebody else root their phone and it didn't work with their razer blade either, they had to use some very old laptop.
Usyless said:
Yeah I remember I helped somebody else root their phone and it didn't work with their razer blade either, they had to use some very old laptop.
Click to expand...
Click to collapse
Guys, sorry for the off-topic, is available the dark mode for razer menu? i can't find it
frannet said:
Guys, sorry for the off-topic, is available the dark mode for razer menu? i can't find it
Click to expand...
Click to collapse
What do you mean razer menu? if you mean settings then it's a MAYBE.
on a gsi, dark mode is available
on stock android 9 it is possible. you need to use smali patcher to enable signature spoofing and then use swift theme installer alpha (substratum themes won't theme the settings)(you need to contact the developer to get the alpha version as others wont work)
Usyless said:
What do you mean razer menu? if you mean settings then it's a MAYBE.
on a gsi, dark mode is available
on stock android 9 it is possible. you need to use smali patcher to enable signature spoofing and then use swift theme installer alpha (substratum themes won't theme the settings)(you need to contact the developer to get the alpha version as others wont work)
Click to expand...
Click to collapse
Yeah I talk about the settings menu. I thought dark mode was available for all android versions ??
frannet said:
Yeah I talk about the settings menu. I thought dark mode was available for all android versions ?
Click to expand...
Click to collapse
yeah tbh idek, all the android fanboys were saying at how long it took apple to make a dark mode but it was implemented in android 10 later than ios 12 I swear ?
but as you are rooted you should be able to get a dark mode, just do as I said with smali patcher and the swift installer alpha
i
Usyless said:
yeah tbh idek, all the android fanboys were saying at how long it took apple to make a dark mode but it was implemented in android 10 later than ios 12 I swear ?
but as you are rooted you should be able to get a dark mode, just do as I said with smali patcher and the swift installer alpha
Click to expand...
Click to collapse
Hahaha, yeah, If I'm honest, dark mode in iOS work fine, very fine, normally I use my iPhone 11 and I play with android devices for.. for play with the OS and develoment OS, and as second andriods phone for maybe.... I go to check the gsi mode, thanks guy!!
Hello guys,
ive been using magisk module of ios emoji (from here) just fine on 1.1.7. Then I updated on 1.1.8 (via OTA method - lost root, fastboot booted patched boot.img - rooted again) and the module suddenly stopped working - simply doesnt appear anywhere. I tried to delete it, install it again, reboot device, but no luck. Tried even different modules of iOS emojis, still not working.
My ionly other module Fullscreen/immersive gestures is working fine after the update. Magisk app updated on thle latest version.
Any idea what could be the issue?
Thank you!
Try this: https://forum.xda-developers.com/t/...dex-facebook-samsung-twemoji-windows.3418801/
Create Magisk Module and Flash it over Magiskt, the internal flash method from app is not working properly.
If its not working download FX File Manager > Grant Root and delete all Folders in \Root\data\fonts\files
Restart your phone and you should get the iOS Emoji's. It could be that you need to delete these folders in \files again after the next Gboard Update
paper88 said:
Try this: https://forum.xda-developers.com/t/...dex-facebook-samsung-twemoji-windows.3418801/
Create Magisk Module and Flash it over Magiskt, the internal flash method from app is not working properly.
If its not working download FX File Manager > Grant Root and delete all Folders in \Root\data\fonts\files
Restart your phone and you should get the iOS Emoji's. It could be that you need to delete these folders in \files again after the next Gboard Update
Click to expand...
Click to collapse
You're a life saver, thank you so much, I really appreciate it, worked perfectly!
paper88 said:
Try this: https://forum.xda-developers.com/t/...dex-facebook-samsung-twemoji-windows.3418801/
Create Magisk Module and Flash it over Magiskt, the internal flash method from app is not working properly.
If its not working download FX File Manager > Grant Root and delete all Folders in \Root\data\fonts\files
Restart your phone and you should get the iOS Emoji's. It could be that you need to delete these folders in \files again after the next Gboard Update
Click to expand...
Click to collapse
I couldn't get it to work no matter what procedure I tried to follow. Currently running on 1.1.7 with the 16.4 beta magisk module but I have zero luck.
I just noticed that I'm a beta tester of GBoard. Can it have an impact? Not sure if anyone tried it with Beta version.