Related
To avoid a novel, I'll just the list the steps I did. I had an ancient version of clockwork and paranoid android rom on my N7, not sure what version and I wanted to get Cyanogenmod 10.2.1 on there along with TWRP.
1. Downloaded TWRP from playstore, installed under paranoid rom, also downloaded CM on SD
2. Used TWRP under paranoid rom to install CM and Gapps
3. TWRP rebooted N7, old version of clockwork showed up instead of TWRP
4. Flashed CM, it worked
5. Installed RomManager, updated to newest stable CM update, installed it, rebooted
6. Once rebooted, playstore and rom manager crashes all the time
7. Hold down Vol Down while booting brought me to fastboot
8. If I select recovery mode, it gets stuck on google screen
9. Tried to push latest CWM via fastboot, it says it pushed it, but I'm still stuck on google screen. It does get back in to the OS still, but playstore crashes.
I don't care if I have to install CWM or TWRP, I just want to get it out of this state. Any ideas?
Nevermind all that, pushed TWRP instead of CMW via fastboot and it worked.
I am trying to flash my N4 with cyanogenmod following the official wiki.
I'm at the point where I've installed TWRP into recovery, I've wiped everything (I've even formatted them since I couldn't wipe all of it initially), and the only error I see is "unable to mount /usb-otg".
Then, I've "installed" the CN zip files for the 13 and 12 versions, none of them works in the sense that when I reboot the system, I'm always coming back to TWRP.
What's wrong? Any suggestion?
Thanks
I've the same problems with my nexus 4
gerardgerard said:
I am trying to flash my N4 with cyanogenmod following the official wiki.
I'm at the point where I've installed TWRP into recovery, I've wiped everything (I've even formatted them since I couldn't wipe all of it initially), and the only error I see is "unable to mount /usb-otg".
Then, I've "installed" the CN zip files for the 13 and 12 versions, none of them works in the sense that when I reboot the system, I'm always coming back to TWRP.
What's wrong? Any suggestion?
Thanks
Click to expand...
Click to collapse
Hi gerardgerard,
I also wanted to flash my Nexus 4 with Cyanogenmod 12.1. So I installed TWRP into recovery and wiped everything, like it's explained in the wiki. I can also see the error "unable to mount /usb-otg". When I want to reboot the system I always get back to TWRP. Cyanogenmod doesn't boot correctly. Did you find a solution for the problem?
same problem
Hi
I'm having the same problem. As follows:
Cause (my mistake): I have been using Cyanogen-mod nightlies for a couple of months on my Nexus 4, and made the grave mistake of leaving the phone to upgrade one night but without it being plugged in properly - and it ran out of power part way through! (At least, that's what I think happened).
Fortunately, it would boot into bootloader and I could use adb/fastboot. I (re)installed TWRP 2.8.7.0 (from my Mac, using fastboot). And that works fine - I can boot into twrp ok.
Next I loaded the latest nightly from cm (using fastboot - is this what people call sideloading?) and used twrp to install it. It goes through the installation fine (the only error message is that it can't mount /usb-otg). But when I reboot it just goes back to twrp.
I then tried installing the earlier cm nightly that I know worked, but with the same result.
Finally, before I first installed cm I did a backup (using twrp), and I have tried recovering that. It seems to do all the right things, but again when I reboot it just goes back to twrp.
Any suggestions would be welcome.
Thanks
J
Flash back to a completely stock ROM and run through the set up to make sure everything works. Then copy CM to the phone, reboot to fastboot, flash twrp, immediately boot into recovery using the volume and power button without leaving fastboot, wipe data, cache, system, flash CM, reboot.
If the phone will not boot after flashing a stock ROM, boot to fastboot, flash the userdata.img file, and immediately go to stock recovery without leaving fastboot, wipe data/cache, reboot.
It works now!
I managed to fix the problem ... I found this guide for the Nexus 5:
http://forum.xda-developers.com/google-nexus-5/general/tutorial-how-to-flash-factory-image-t2513701
and I applied those instructions. It didn't work first time, so I just repeated them and now it's working. I used the 5.1.1 stock downloaded from https://developers.google.com/android/nexus/images#occam.
I guess this is what audit13 means in their post - so thanks are due there.
I will next reinstall twrp and cm and I don't expect any problems with that (having done it successfully before).
Smaje
I'm having a very difficult time getting this phone setup. I can get very, very close... but then it starts boot looping into recovery.
So starting at the beginning, here is what I did:
- Booted up phone, make sure it works and connects to wifi (I find out later that it got encrypted, even though I didn't set a PIN).
- Inside the OS on first boot, I install and use the official bootloader unlock APK from Asus.
- Rebooted into the bootloader and fastboot flashed TWRP.
- Rebooted into TWRP and flashed the Oreo modem, current unofficial Carbon OS 6.1, nano gapps, and magisk 16.6.
- Rebooted and the Carbon ROM logo comes up. It works for about 2-3 minutes, then reboots.
- After many attempts to decrypt (and a lot of help from the forum), I successfully restore the phone to "WW_ZE552KL_14.2020.1712.85_M3.10.47.15_Phone-user.raw.zip" with the Asus tool.
- Phone is fixed and booting again to the OS, but I'm back to square one.
Second attempt:
- Thinking I need to flash the raw Oreo ROM (instead of just the Oreo modem), I use the Asus tool to flash "WW_ZE552KL_15.0410.1803.55_M3.10.47.19_Phone-user.raw.zip"
- The phone works fine and is now an Oreo ROM with an Oreo modem
- It's still unlocked, so I rebooted into the bootloader and fastboot flashed TWRP.
- Rebooted into TWRP and flashed the current unofficial Carbon OS 6.1, nano gapps, and magisk 16.6.
- Rebooted and the Carbon ROM logo comes up. It works for about 2-3 minutes, then reboots.
- After the reboot, it goes to TWRP... whether I just let it boot on its own, or press power when it says: Start - Continue to boot >
What am I doing wrong?
You're having a rough go at this one eh.
I know we talked about this before, but did you try a factory reset and wiping cache/dalvik before rebooting?
Yes. As we discussed before, you can't wipe cache from TWRP. So I'd wipe dalvik from TWRP, then reboot to the bootloader to do a "fastboot format cache".
I'm going to try a different ROM later this afternoon. Maybe that will make a difference.
Flapjack said:
I'm going to try a different ROM later this afternoon. Maybe that will make a difference.
Click to expand...
Click to collapse
Hello! I've been able to boot any ROM by:
1. flashing TWRP
2. rebooting to recovery
3. installing the ROM zip
4. rebooting to bootloader
5. fastboot continue
But when I restart the phone, it always boots to recovery(TWRP), so I have to repeat steps 4 and 5 to boot the ROM, which is
Could you try and tell me if it works for you too?
I'm gonna take a moment to read about the boot process in depth, as it seems there is no straightforward solution to this out there.
junglesnake said:
Hello! I've been able to boot any ROM by:
1. flashing TWRP
2. rebooting to recovery
3. installing the ROM zip
4. rebooting to bootloader
5. fastboot continue
But when I restart the phone, it always boots to recovery(TWRP), so I have to repeat steps 4 and 5 to boot the ROM, which is
Could you try and tell me if it works for you too?
I'm gonna take a moment to read about the boot process in depth, as it seems there is no straightforward solution to this out there.
Click to expand...
Click to collapse
1) Flash Oreo RAW (can be downloaded from @Saktis_STi' s unlocking thread.
2) Boot till system
3) Flash TWRP
4) Flash ROM, Magisk, GApps
5) Reboot
The reason why it reboots to TWRP is because of 'encryption' thingy.
BootloaderBoi said:
1) Flash Oreo RAW (can be downloaded from @Saktis_STi' s unlocking thread.
2) Boot till system
3) Flash TWRP
4) Flash ROM, Magisk, GApps
5) Reboot
The reason why it reboots to TWRP is because of 'encryption' thingy.
Click to expand...
Click to collapse
many many thanks! I was able to get Ressurection Remix working by now
your steps were right, and I will detail them better to tell how I made it work for others reading this thread:
1) Flash Oreo RAW
1.1 - @Saktis_STi's thread is a bit outdated. I downloaded the newest firmware from Asus website.
1.2 - I also had to find a recent recovery.img, which I think I got it from here https://forum.xda-developers.com/zenfone-3/how-to/original-recovery-img-boot-img-zenfone-t3572188
1.3 - I used the stock recovery's adb sideload to flash the stock ROM
2) Flash TWRP - all good here
3) Flash ROM, Magisk, GApps
3.1 - I wiped system, data, cache and dalvik.
3.2 - I flashed RR ROM, GApps and Magisk (EDIT 2: install all three before the first custom ROM boot, or GApps won't work)
3.3 - Performed a Factory Reset
4) REBOOTED TO GLORY!
For what it seems, the stock ROM encryption that is performed on the stock's first boot was the enemy.
Now one last thing... In Security -> Encription, my device is NOT encrypted.
Do I run the risk of ruining everything if I encrypt it?
EDIT: No, it didn't break, working fine
junglesnake said:
1) Flash Oreo RAW
1.1 - @Saktis_STi's thread is a bit outdated. I downloaded the newest firmware from Asus website
Click to expand...
Click to collapse
lmao. His RAW firmware version is the latest version though
https://forum.xda-developers.com/zenfone-3/development/updated-unlock-relock-bootloader-t3749456
Anyways, enjoy your phone running on custom ROM :good:
Hey guys,
I just oem unlocked my new 6T and have access to the bootloader. As I try to install TWRP with
HTML:
fastboot boot imagename.img
my computer says that it pushes the image just fine, but my phone restarts and then never makes it past the fastboot splash screen instead of loading up TWRP.
I was following the fajita (6T) instructions from the lineage OS website.
The first time I did it it worked, but following the instructions on installing lineage and telling me to wipe and format data, both the recovery seems to be gone and i cannot fastboot boot into TWRP.
Can you help?
Seems the same with what i experienced. Have you tried installing a fastboot rom? I had my oneplus 6t bootlooped into fastboot mode even if i try to turn it off, it just boots back automatically to fastboot mode. Last resort was to flash a fastboot rom. That worked for me.
thalesian2020 said:
Hey guys,
I just oem unlocked my new 6T and have access to the bootloader. As I try to install TWRP with
HTML:
fastboot boot imagename.img
my computer says that it pushes the image just fine, but my phone restarts and then never makes it past the fastboot splash screen instead of loading up TWRP.
I was following the fajita (6T) instructions from the lineage OS website.
The first time I did it it worked, but following the instructions on installing lineage and telling me to wipe and format data, both the recovery seems to be gone and i cannot fastboot boot into TWRP.
Can you help?
Click to expand...
Click to collapse
What TWRP version are you trying to install?
jp0469 said:
What TWRP version are you trying to install?
Click to expand...
Click to collapse
I tried 3.3.1.1. and 3.2.3.0.
What you are describing, I'm going to assume you are trying to install Lineage 17. You can't install TWRP if you are going Android 10, at least that's the conclusion I've come to at this point in time. It will fail to boot or end up in crash dump mode every time you try and enter recovery if you are on a custom ROM. If you are on Android 9, it's not an issue. I believe it's OK stock as well, but I don't know haven't tried, haven't been stock in a long time.
For LOS 17, only boot the TWRP image, never boot to recovery, never run the TWRP installer. You will likely still have to format data.
I have a post here, from when I had a similar issue. (instructions)
You'll notice the OmniRom instructions don't mention installing TWRP, only booting it.
Once I was in your spot, I always went back to stock using the fastboot ROM, installed TWRP, updated (still using TWRP), then started over with my install.
Well no, i was actually trying to install Lineage 16, which is Android 9 I believe.
The problem for me is that I do not get to the point where TWRP opens after "fastboot boot"ing it. So I understand, I should use a fastboot stock ROM? Is there such a thing? Where would I find it? Or would it be an OnePlus Oxygen ROM that I can fastboot?
Quickest way to start over:
To get back straight your gonna need to access a Windows PC, and run the MSM tool. Make sure you install both OnePlus and Qualcomm drivers. ( Don't wait for Windows, just pre install the drivers) here are some links. Not my work. Please be sure to thank the developers for creating and hosting these tools ?
MSM Tool:
https://forum.xda-developers.com/oneplus-6t/how-to/tool-6t-msmdownloadtool-v4-0-oos-9-0-5-t3867448
OnePlus Drivers:
https://androidfilehost.com/?fid=11410963190603879743
Qualcomm drivers:
https://androidfilehost.com/?fid=11410963190603879743
thalesian2020 said:
Well no, i was actually trying to install Lineage 16, which is Android 9 I believe.
The problem for me is that I do not get to the point where TWRP opens after "fastboot boot"ing it. So I understand, I should use a fastboot stock ROM? Is there such a thing? Where would I find it? Or would it be an OnePlus Oxygen ROM that I can fastboot?
Click to expand...
Click to collapse
Were you on Android 10 before (OOS)? That will do that. LOS 16 is Android 9 and should have no problems installing TWRP or booting to it.. For LOS 16 I'd go back to 9.0.17, then install LOS 6T.
I posted these LOS install instructions a long time ago for another user.
Remember the MSM Tool will relock your bootloader so if something goes wrong the MSM Tool is your only choice. That is why it is always the last thing I resort to.
Thread to get Fastboot stock Roms if you want to try that route first.
Hey guys,
thank you so much for all your help. I've managed to use mauronofrios workaround here on xda to put my phone in a 9.0.17 state again (no idea what i had originally), and this way i could fastboot the twrp image again. so that worked fine, but so far flashing lineage hasnt worked, for whatever reason it seems to boot into a lineageos kind of recovery only (which i didnt even know existed).
So i guess in terms of this thread the problem is solved. Thank you again!
thalesian2020 said:
Hey guys,
thank you so much for all your help. I've managed to use mauronofrios workaround here on xda to put my phone in a 9.0.17 state again (no idea what i had originally), and this way i could fastboot the twrp image again. so that worked fine, but so far flashing lineage hasnt worked, for whatever reason it seems to boot into a lineageos kind of recovery only (which i didnt even know existed).
So i guess in terms of this thread the problem is solved. Thank you again!
Click to expand...
Click to collapse
Did you see my Lineage install instructions above? LOS installs its on Recovery when you flash the ROM. When om Android 9, boot TWRP, flash the TWRP installer, reboot to Recovery, install LOS 16, flash the TWRP installer again (replaces the LOS recovery that was installed), reboot to Recovery, install gapps / magisk if desired, reboot.
Read my instructions post though, the first time install is different, as you need LOS on both slots. Updating is different as well, its much easier.
It should go smoothly.
OhioYJ said:
Did you see my Lineage install instructions above? LOS installs its on Recovery when you flash the ROM. When om Android 9, boot TWRP, flash the TWRP installer, reboot to Recovery, install LOS 16, flash the TWRP installer again (replaces the LOS recovery that was installed), reboot to Recovery, install gapps / magisk if desired, reboot.
Read my instructions post though, the first time install is different, as you need LOS on both slots. Updating is different as well, its much easier.
It should go smoothly.
Click to expand...
Click to collapse
Do I need to be on Android 9 Stock when I start that process? What I did was boot into TWRP, flash TWRP installer, reboot into recovery, then format and wipe ALL partitions (except USB), then reboot into recovery again and then flash LOS, flash TWRP, reboot into recovery, flash LOS, flash TWRP, reboot system. Still no luck...
thalesian2020 said:
Do I need to be on Android 9 Stock when I start that process? What I did was boot into TWRP, flash TWRP installer, reboot into recovery, then format and wipe ALL partitions (except USB), then reboot into recovery again and then flash LOS, flash TWRP, reboot into recovery, flash LOS, flash TWRP, reboot system. Still no luck...
Click to expand...
Click to collapse
Wiping, Dalvik / ART, System, and Vendor is generally a bad idea. You can do them in certain situations, this isn't one of those situations you should be wiping those though. Factory reset, means the slider on the main page of the wipe screen that says swipe to factory reset, format data is the button that says format data. Don't do anything extra. If you did, yeah I would go back to 9.0.17 using the fastboot rom again, that will put everything back on both slots.
like OhioYJ stated, don't use advanced wipe. re-run the msm tool. Then follow his instuctions. You shouldn't need to preform any manual data wiping. The process of flashing will do everything required. looks like you're almost there
Thanks guys. I will try it out and let you know.
Edit: So I finally managed to properly install LOS - OhioYJ, your instructions worked! I installed 9.0.17 and went from there without wiping any additional partitions.
One questions remains: in your instructions you mention that after installing LOS once, you can update LOS as normal and you mention doing it via the recovery with flashing TWRP or GAPPS later again. Is it possible to do the update via the normal update function of LOS as well? Or will that overwrite TWRP?
You guys are awesome. Thank you so much for your help!
I seem to be stuck on the fastboot screen as well. Being on a MAC, anytime i try to do something in fastboot it goes straight back to the fastboot screen. I Thought I was on Android 10.0 trying to install recovery for that lead to bootloop of fastboot, tried using the Pie recovery and same thing. I am open to suggestions.
Thanks.
OhioYJ said:
What you are describing, I'm going to assume you are trying to install Lineage 17. You can't install TWRP if you are going Android 10, at least that's the conclusion I've come to at this point in time. It will fail to boot or end up in crash dump mode every time you try and enter recovery if you are on a custom ROM. If you are on Android 9, it's not an issue. I believe it's OK stock as well, but I don't know haven't tried, haven't been stock in a long time.
For LOS 17, only boot the TWRP image, never boot to recovery, never run the TWRP installer. You will likely still have to format data.
I have a post here, from when I had a similar issue. (instructions)
You'll notice the OmniRom instructions don't mention installing TWRP, only booting it.
Once I was in your spot, I always went back to stock using the fastboot ROM, installed TWRP, updated (still using TWRP), then started over with my install.
Click to expand...
Click to collapse
Twrp is working fine with Android 10, using mauronofrio version and magisk 20.2
callumbr1 said:
Twrp is working fine with Android 10, using mauronofrio version and magisk 20.2
Click to expand...
Click to collapse
Yeah it starting to seem like it maybe isolated to Lineage. You cant install TWRP with LOS 17. Someone else mentioned in the Omni thread that it worked. This thread is about Lineage, but that should be clarified, or clearer.
From 6T (purchased from oneplus.com), any time I follow the instructions for how to flash one of the custom ROMs, I get stuck at the bootloader with no working rom.
I was able to use the MSMTool to restore to 9.0.13. I upgraded a few times flashing OnePlus6TOxygen_34_OTA_024_all_1909112343_9fd6e0057b8747dc, which works, but when I try to flash a custom ROM, I cannot get past the bootloader. I say a few times because I've tried this for a few days now with no success.
Most recently, I used the Flash-all.bat inside 10.3.0-OnePlus6TOxygen_34_OTA_042_all_1912142031_d9ef3-FASTBOOT
I am currently on 10.3.0, with twrp-3.3.1-31-fajita-Q-mauronofrio installed using the fastboot flash boot_a twrp-3.3.1-31-fajita-Q-mauronofrio.img then fastboot boottwrp-3.3.1-31-fajita-Q-mauronofrio.img commands from fastboot.
I can then install Magisk 19.4 or 20.3, however again when I try to flash a custom ROM, I cannot get past the bootloader.
What am I doing wrong?
When you 'fastboot boot' twrp, you can't flash twrp as .img file after that..... (There is no recovery partition on our phone, only a boot one)
If you flash a twrp img it will overwrite boot partition with only twrp and no kernel... Basic knowledge. Once temporarily booted in twrp by 'fastboot boot' command you must flash the installer, meaning the .zip file.
Then reboot your phone in twrp and flash whatever you want
Always latest versions of Magisk, why flashing a deprecated 19.4?
Striatum_bdr said:
When you 'fastboot boot' twrp, you can't flash twrp as .img file after that..... (There is no recovery partition on our phone, only a boot one)
If you flash a twrp img it will overwrite boot partition with only twrp and no kernel... Basic knowledge. Once temporarily booted in twrp by 'fastboot boot' command you must flash the installer, meaning the .zip file.
Then reboot your phone in twrp and flash whatever you want
Always latest versions of Magisk, why flashing a deprecated 19.4?
Click to expand...
Click to collapse
I was having an issue with the boot command in 10.3.0, which is how I found the flash command, and using both of those seemed to work (at least get me into twrp).
Now I am able to just run fastboot boot twrp-3.3.1-31-fajita-Q-mauronofrio.img and it works.
I was using 19.4 because somewhere in here someone mention twrp not working with magisk 20.3.
I've had no issues with 20.3 and twrp, so I will continue to use 20.3
The steps I use to flash a custom ROM (after twrp is installed)
1. remove the lock screen security from the existing ROM
2. boot straight into recovery from the existing ROM
3. wipe Data, Cache, and Dalvik by swiping right to factory reset from the wipe menu
4. flash the ROM from internal storage using the Install button
at this point I've tried a couple of approaches including a reboot here to see if the ROM flashed, and also installing twrp right after flashing ROM so that I will have a working twrp install.
Either way, I can never get past the bootloader.
Am I performing these steps correctly?
s7itch3s said:
I was having an issue with the boot command in 10.3.0, which is how I found the flash command, and using both of those seemed to work (at least get me into twrp).
Now I am able to just run fastboot boot twrp-3.3.1-31-fajita-Q-mauronofrio.img and it works.
I was using 19.4 because somewhere in here someone mention twrp not working with magisk 20.3.
I've had no issues with 20.3 and twrp, so I will continue to use 20.3
The steps I use to flash a custom ROM (after twrp is installed)
1. remove the lock screen security from the existing ROM
2. boot straight into recovery from the existing ROM
3. wipe Data, Cache, and Dalvik by swiping right to factory reset from the wipe menu
4. flash the ROM from internal storage using the Install button
at this point I've tried a couple of approaches including a reboot here to see if the ROM flashed, and also installing twrp right after flashing ROM so that I will have a working twrp install.
Either way, I can never get past the bootloader.
Am I performing these steps correctly?
Click to expand...
Click to collapse
I don't know I don't flash custom ROMs anymore, too old for that stuff and need my time for me.
There are specific instructions for each custom ROM it's better to ask in dedicated threads, some of them need to have OOS in both slots before, some of them need to be fleshed in both slots. Normally you eventually wipe things, flash the ROM and twrp to keep it, then reboot to twrp (necessary to boot on the slot where the ROM is actually fleshed, which is always the non active slot, which become the new active slot) and flash Gapps and Magisk ( because Gapps and Magisk can be flashed only in active slot) then reboot system
s7itch3s said:
Am I performing these steps correctly?
Click to expand...
Click to collapse
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
OhioYJ said:
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
Click to expand...
Click to collapse
Sir, apology for being an old noob, I am on OOS 10.3.2 TWRP 3.3.1-32 can I follow the above guide? If Yes,
Why aren't we using the "Lineage Recovery" provided in "Lineage OS Downloads" page?? If we use it, will the above instructions change ? What are the cons of using it?
Sorry again for asking!! Can you please share me the Link to Open Gapps which Will be suitable in my scenario ?
Advised Sloth said:
Sir, apology for being an old noob, I am on OOS 10.3.2 TWRP 3.3.1-32 can I follow the above guide? If Yes,
Why aren't we using the "Lineage Recovery" provided in "Lineage OS Downloads" page?? If we use it, will the above instructions change ? What are the cons of using it?
Sorry again for asking!! Can you please share me the Link to Open Gapps which Will be suitable in my scenario ?
Click to expand...
Click to collapse
Historically Lineage / CM recovery was hit or miss, or TWRP or other recoverys worked better. To be fair I haven't even tried the Lineage recovery. So maybe that is no longer true? Right now, I know TWRP works. The updated instructions link up there has links in it, FYI, link OpenGapps. OpenGapps can be found here. You will be using Arm64, Android 10 obviously.
Since you are already on 10.3.2 (I assume you were on 10.3.1 before) you should be good to skip the step about fastboot ROM or install OOS, and you already have TWRP., so you should be able to go right on to backing everything up, wiping everything, and installing Lineage. (So you can skip the first few steps)
Anymore questions feel free to ask.
OhioYJ said:
Historically Lineage / CM recovery was hit or miss, or TWRP or other recoverys worked better. To be fair I haven't even tried the Lineage recovery. So maybe that is no longer true? Right now, I know TWRP works. The updated instructions link up there has links in it, FYI, link OpenGapps. OpenGapps can be found here. You will be using Arm64, Android 10 obviously.
Since you are already on 10.3.2 (I assume you were on 10.3.1 before) you should be good to skip the step about fastboot ROM or install OOS, and you already have TWRP., so you should be able to go right on to backing everything up, wiping everything, and installing Lineage. (So you can skip the first few steps)
Anymore questions feel free to ask.
Click to expand...
Click to collapse
First of all, thank you very much for your time and explanation.
Sir, so i will proceed as follows:
* Boot into TWRP Recovery
* Perform "swipe to factory reset" & "swipe to wipe data"
* Reboot to TWRP recovery again
* Flash LOS 17.1 on slot A
* Reboot to TWRP recovery again
* Flash LOS 17.1 on slot B
* Reboot to system
Sir, please check are my steps correct? If not,
From which step( steps mentioned in your guide) should i start?
Last query is, which GApps zip will be best for me, micro/nano/pico/tv stock, If i want max coverage of google?
Very sorry for knocking you repeatedly!!!
Advised Sloth said:
First of all, thank you very much for your time and explanation.
Last query is, which GApps zip will be best for me, micro/nano/pico/tv stock, If i want max coverage of google?
Click to expand...
Click to collapse
Your starting point is correct. However make sure you don't miss the re-install TWRP after flashing Lineage each time, and the second time you need to flash Gapps before you reboot to system.
Personally I always do Nano. Anything else you need (that would be included in Micro) can be installed from the Play store. Nano at least includes all the things that can't be installed from the play store.
Pico has the least in it. TV is for TV devices. On OpenGapps there is a box next to each package you can click and it will tell you exactly what is in each package.
OhioYJ said:
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
Click to expand...
Click to collapse
Sorry for the necropost, but this also works for TWRP 3.6 and Lineage 18.1. I initially had a problem with the default TWRP for my 6t. During the initial TWRP fastboot the version on their site caused a firmware error which I could just barely get out of, but it screwed up the system boot process in some subtle way that even the fixed version of TWRP (found on this site) couldn't solve.
After trying your instructions above, it didn't work the first time because of the screwed up system boot. It just kept trying to boot to recovery. I suspected a firmware error and was almost going to do an mcmdownload soft-brick rescue. I tried one last thing, using the TWRP on the system to sideload the stock ROM. That worked and patched up the system boot process. Once I booted and ran through some basic initialization to make sure developer options were properly set I followed the above instructions and it worked nearly flawlessly.
One strange thing. After I installed Lineage 18.1 and TWRP to both partitions (as well as Gapps / magisk), it rebooted to system and almost booted without incident -- except a large circular logo popped up that said 100% and stopped. I figured that that meant someting completed properly, so I powered off, waited 10 seconds, powered on and then the Lineage green system initialization spinner came up for a few minutes and it went through the user initialization sequence.
Thanks. I almost gave up and bought a new phone.
OhioYJ said:
I've updated these instructions here, they are the same, just added to them really.
This is how I install Lineage 17. (If you are doing 16, replace 10.3.0 with 9.0.17, and the Q image of TWRP with the Pie image)
- Install 10.3.0 fastboot ROM again to start over, boot it once. Just to make sure everything is good.
- Reboot to fastboot.
- Boot the Q image of TWRP.
- Run the TWRP installer, reboot to recovery
- You backed everything up right?
- Factory reset (This is the slider at the bottom in the wipe menu).
- Format data. (This is the button that says Format data in the wipe menu)
- Do NOT wipe cache, do not Wipe system, do NOT Wipe Dalvik / ART, do not add anything else, Just Factory Reset and Format Data. After doing those two Reboot to Recovery one more time. You must do this after formatting data.
- Now transfer Lineage and TWRP to your phone, Windows / Linux should see TWRP fine as a media device when plugged in.
- Install Lineage
- Run the TWRP Installer.
- Reboot to Recovery.
- Install Lineage (You need Lineage on both slots, so yes run it again)
- Run the TWRP Installer (yes again).
- Reboot to Recovery.
- Install Gapps if you want them.
- Install Magisk 20.3 if you use Magisk. I used 20.3 it works fine. (20.4 also fine) Do not install modules or other add ons at this point. Boot once and go through the setup and everything, then install your add-ons.
- Be aware the phone will restart once, then Lineage will start up and all will be good.
From that point on updating should just be like normal :
- Reboot to recovery
- Flash Lineage.
- Flash TWRP Installer
- Reboot to Recovery
- Flash Gapps. (Assuming you use them, if you installed them once you must continue to install them or do a clean install)
- Flash Magisk. (If you use it)
- Reboot to system.
- No loss of data, or anything.
- No need to flash anything twice etc.
I've posted similar instructions here. It was just for LOS 16, same thing essentially though.
Click to expand...
Click to collapse
OhioYJ, these are great instructions but it initially left me with questions about how that procedures would create duplicate installs on slot A and B. The answer is of course that the Lineage installer for the 6t knows about the dual slot setup and always writes to the inactive slot. Booting into recovery activates the inactive slot so that installing again after that installs to the other slot and now you have Lineage on both slots. The installer for TWRP always installs to both slots and is needed because Lineage always installs its recovery handler and you don't want that so you overwrite.
PS: TWRP has an option for installing itself after installing the requested package. Would that be just as good as installing the TWRP zip?
PPS: I had to do an 'adb push' of the Lineage and TWRP zips to sdcard for the installs. Unfortunately installing and slot switching makes the sdcard unavailable so you have to push the zips again. Is there somewhere I can write them to that I don't lose access to after a boot to recovery?