USB pins and additional steering wheel control - Android Head-Units

I recently installed a unbranded unit model 7918 from eBay) with 8227L chip in my 2015 Mazda 5 sport. Things are working fine. I do have the following questions
1. What is the difference between 4 pin and 6 pin USB sockets on the back of the unit?
2. My steering wheel control communicates with the Android unit by using key1 (resistance) and key2 (ground) without any interface. I am hoping to add more buttons on the steering wheel. Can this be done wirelessly?

Related

Joying HU to ALFA ROMEO 147 Steering Wheel Buttons

Hi
I start installing Joying HU which have KEY1 and KEY2 for Steering Wheel Buttons,
but Alfa 147 have 3 wires for steering wheel buttons labeled as ;
10 Input 1 for Steering Wheel Buttons
11 Input 2 for Steering Wheel Buttons
12 Reference for Steering Wheel Buttons
I try to connect KEY1 and and KEY2 be twin pin 10 and 11 but it doesn't work
Do I have to have pin 12 connected to CAR GND or HU GND ?
here is the picture, not shure which pins are 10,11,12
wires are:
- yellow/green
- black/purple (I think this is GND)
- pink
Sorry,
I just see this video, where thay connect the GND from the steering wheel buttonst to the HU GND...
https://www.youtube.com/watch?v=jjrcGuB0D5s
will do so

How to use steering wheel controls with the Atoto A6 Pro.

Tracking this info down was a nightmare for me. Hope this is useful to someone.
Requirements:
• Axxess aswc-1 Universal Steering Wheel Control Interface. (link)
• Time and patience.
IMPORTANT: DO NOT use the 3.5mm Female input (SWC IR-WIRELESS Steering Wheel Key Control Port) on the back of the Atoto A6 Pro. This port does not work for some reason.
**Connections to the Car**
1. Download the vehicle specific instructions for your car, as well as the "Axxess Steering Wheel Control Interface Installation Manual" (two different PDFs) from https://axxessinterfaces.com.
2. Follow the vehicle specific instructions to first connect the AWSC-1 to your car.
**Connections to the Radio**
1. The aswc-1 includes a female 3.5mm connector with a brown and brown/white wire coming out. Use this to connect to the Atoto’s Steering Wheel Key(+) and Steering Wheel Key#(+) wires.
2. Connect the "Steering Wheel Key+” wire of the Atoto A6 to the Brown/White wire of Axxess ASWC-1, connect the "Steering WheelKey#+” wire of the Atoto A6 to the Brown wire of the aswc-1
(yes, both of these wires are positive. I don't know who or why, but it works.)
3. Plug the male 3.5 mm jack from the aswc-1, into the female 3.5 mm jack that you wired up in step 2.
4. The ASWC-1 will NOT auto detect the Atoto A6. (don't worry, not a problem)
5. Follow the instructions from page 12 of the "Axxess Steering Wheel Control Interface Installation Manual" to change your radio type.
Change your radio type to "Visteon". (Visteon is radio type 8).
7. At this point you have completed configuring the aswc-1. Next, move on to your radio.
8. From the radio navigate to: Settings>Default settings>Steering wheel program.
9. Once at the screen press "Reset".
10. Then press any key value from the menu, it will begin to flash.
11. Finally press one of the buttons on your steering wheel. The flashing key (from step 10) on your radio will stop flashing, and a triangular symbol will appear on the key. This indicates the key has been successfully programmed.
repeat steps 10 and 11 until you have programmed all the steering wheel control buttons. :good:
first thanks for the guide there is nothing of information of those two wires anywhere.
second, I followed all the steps except the manual programming of the stereo, but use the axxess app to program the module as Visteon but I still can not make it to work, I know that axxess is well connected to the car because it already worked with my previous stereo but honestly I do not know what else I can do to make it work.
ATOTO steering wheel control for cars with resistance circuit
Just wanted to mention that if you vehicle's steering wheel controls is based on a simple resistance circuit, then it can be connected directly to ATOTO with no need for Axxess aswc-1. My vehicle (2011 Subaru WRX) was in this category.
For my vehicle, there are two wires in the harness and the resistance between these two wires will change depending on which SWC button is pressed on the steering wheel. Unfortunately, the ATOTO documentation is dead wrong how to hook this up. The manual says that if your vehicle has two wires, you should connect the two wires from the vehicle to the "Steering WheelKey#+” and "Steering WheelKey+” wires. That doesn't work. Instead you should connect one of the vehicle wires to chassis ground and the other vehicle wire to either of the ATOTO "Steering WheelKey" wires. I think the ATOTO wires are both labeled as "+" because they assume the vehicle SWC will provide a path to ground. Hope this information helps someone else.
Thanks a lot for your sharing! Really helpful!
jackohound said:
Just wanted to mention that if you vehicle's steering wheel controls is based on a simple resistance circuit, then it can be connected directly to ATOTO with no need for Axxess aswc-1. My vehicle (2011 Subaru WRX) was in this category.
For my vehicle, there are two wires in the harness and the resistance between these two wires will change depending on which SWC button is pressed on the steering wheel. Unfortunately, the ATOTO documentation is dead wrong how to hook this up. The manual says that if your vehicle has two wires, you should connect the two wires from the vehicle to the "Steering WheelKey#+” and "Steering WheelKey+” wires. That doesn't work. Instead you should connect one of the vehicle wires to chassis ground and the other vehicle wire to either of the ATOTO "Steering WheelKey" wires. I think the ATOTO wires are both labeled as "+" because they assume the vehicle SWC will provide a path to ground. Hope this information helps someone else.
Click to expand...
Click to collapse
On the Atoto a6 there is a Steering Wheel Key + (Orange wire) and a Steering Wheel Key# + (Brown, Black Stripe).
On my Metra harness there is a Steering Wheel 1 (Green), Steering Wheel 2 (Blue), 12v (Red) and Ground (Black). All for the Steering controls.
This is on my 11 WRX.
andrewd5418 said:
On the Atoto a6 there is a Steering Wheel Key + (Orange wire) and a Steering Wheel Key# + (Brown, Black Stripe).
On my Metra harness there is a Steering Wheel 1 (Green), Steering Wheel 2 (Blue), 12v (Red) and Ground (Black). All for the Steering controls.
This is on my 11 WRX.
Click to expand...
Click to collapse
Can you give a link to the Metra harness you have? The 2011 WRX steering wheel controls have 2 or 3 wires depending on your car's options, so having 4 steering wheel wires on the Metra harness seems strange. I'll paste one of the wiring diagrams here, guessing at your car's options. If you have trouble pasting a link to a Metra part like 70-8901 , just add some spaces onto the URL to make it look like plain text.
Also it would help to know if your 2011 WRX came originally from the factory with a non-bluetooth radio, bluetooth radio, or with the Navigation. The important point here is whether your steering wheel has just the Vol+/Vol-/Mode/Seek button cluster or if you also have the other cluster for controlling the bluetooth phone.
My guess is that you should connect Metra SteeringWheel1 to ATOTO Steering_Wheel_Key+, connect Metra SteeringWheel2 to Chassis Ground, and leave the any other steering wheel specific wires on your Metra harness unconnected since ATOTO doesnt need those. This is just a guess without the other info that I requested.
My bad. It is an "upgraded metra". It won't let me post a link. From auto harness house part AHH-70-7552
My cars a limited no nav. So it has bluetooth.
Sent from my SM-N960U using Tapatalk
andrewd5418 said:
My bad. It is an "upgraded metra". It won't let me post a link. From auto harness house part AHH-70-7552
My cars a limited no nav. So it has bluetooth.
Sent from my SM-N960U using Tapatalk
Click to expand...
Click to collapse
OK, so given that you have harness AHH-70-7552, then you should connect Metra SteeringWheel1 to ATOTO Steering_Wheel_Key+; connect Metra SteeringWheel2 to ATOTO Steering Wheel Key#+; leave the Metra SWC +12 and ground wires unconnected (ATOTO doesnt need those). The "third" common wire from your vehicle's SWC will be correctly connected by ground by the harness itself, as is noted in the AH-70-7552 product page:
*Pin 14 is grounded in the harness for the convenience of the installer. If this connection is not desired, cut the wire that connects between pin 14 and pin 10
Click to expand...
Click to collapse
BTW, you might find this AE64 page useful for details on the pinouts for your subaru's 20-pin connector.
On a separate topic, are you connecting a back-up camera to the ATOTO? Noticed that your Metra harness doesnt have the reverse gear signal.
I was going to eventually and just run a wire from the reverse sensor wire to the units harness
Sent from my SM-N960U using Tapatalk
---------- Post added at 10:39 PM ---------- Previous post was at 10:36 PM ----------
Do you know if I leave the parking brake wire disconnected on the atoto harness?
Sent from my SM-N960U using Tapatalk
andrewd5418 said:
I was going to eventually and just run a wire from the reverse sensor wire to the units harness
Do you know if I leave the parking brake wire disconnected on the atoto harness?
Click to expand...
Click to collapse
Yes, that's what I did on my install and what I would recommend. The ATOTO has a "feature" where it will disable playback of videos unless the parking brake is set, but that feature is disabled by default. There is no particular reason to connect the parking brake wire to the ATOTO unless you plan on enabling that feature.
Atoto swc
Thank you for your tip, my car Mitsubishi Pajero dakar has 2 wires with diferent resisteses, i conected 1 cable from the car to ATOTO and the second cable of the car to ATOTO AND GROUND toghether, that was the only way that worked... if i leave the second cable of atoto without ground it do not work..
Outlander 2015 Problem
Hi All !
I followed your instructions.
I have a Outlander 2015 and a ATOTO Pro A6.
After configuring the AWSC-1, only two buttons on the steering wheel work in the mapping panel (Volume up and skip right) no other wheel button is recongnized by ATOTO
I tried to swap the wires from the male jack connected to Steering key and key# with no luck.
Anybody encountered the same problem ?
Thank you
help what colour
jackohound said:
Just wanted to mention that if you vehicle's steering wheel controls is based on a simple resistance circuit, then it can be connected directly to ATOTO with no need for Axxess aswc-1. My vehicle (2011 Subaru WRX) was in this category.
For my vehicle, there are two wires in the harness and the resistance between these two wires will change depending on which SWC button is pressed on the steering wheel. Unfortunately, the ATOTO documentation is dead wrong how to hook this up. The manual says that if your vehicle has two wires, you should connect the two wires from the vehicle to the "Steering WheelKey#+” and "Steering WheelKey+” wires. That doesn't work. Instead you should connect one of the vehicle wires to chassis ground and the other vehicle wire to either of the ATOTO "Steering WheelKey" wires. I think the ATOTO wires are both labeled as "+" because they assume the vehicle SWC will provide a path to ground. Hope this information helps someone else.
Click to expand...
Click to collapse
I have a 2011 subaru forester sounds like same wires /radio but what wire from the car do I need to connect? I understand I dont need a controller for this? there are 2 wires coming from atoto radio harness but what are the color of wires i need to connect to the car?
inventiveash said:
I have a 2011 subaru forester sounds like same wires /radio but what wire from the car do I need to connect?
Click to expand...
Click to collapse
Did your 2011 Subaru Forester come from the factory with Navigation? If not, then does your steering wheel one cluster of SWC buttons (Vol+,Vol-, Seek+, Seek-, Mode, Mute) or does it also have the second cluster of SWC buttons for controlling Bluetooth phone? These questions affects the color and location of the wires you'll be looking for.
It has volume +&-
Tune up and down
Mode
No mute button
Sent from my SM-G930W8 using Tapatalk
creatingash said:
It has volume +&-
Tune up and down
Mode
No mute button
Click to expand...
Click to collapse
OK, Take that to mean your 2011 Subaru Forester did not come with factory navigation and does not have the Bluetooth steering wheel buttons. In that case, you are looking for the following two wires on your car:
Yellow wire: Connected to pin 14 of your 20-pin Subaru audio connector.
LightGreen with red stripe: Connected to pin 4 of the 20-pin Subaru audio connector.
Refer to pics and pinouts of the 20-pin Subaru connector. Connect one of the above two Subaru wires (either one) to ground. Connect the remaining Subaru wire to ATOTO orange-black steering wheel key (+).
Leave the ATOTO brown-black steering wheel key #(+) unconnected. This worked for me, but others had reported that they needed to connect the steering wheel key #(+) to ground, so you could try that if needed.
Thank you, I will give it a try,
Since you are familiar any idea the best place for finding a reverse light wire easy to get to.
Sent from my SM-G930W8 using Tapatalk
inventiveash said:
any idea the best place for finding a reverse light wire easy to get to?
Click to expand...
Click to collapse
On 2011 Subaru Forester with factory navigation, that wire (a brown wire with yellow stripe) would be brought out to one of the navigation connectors. Don't know if that wire is accessible in your vehicle's instrument panel harness or not.
2015 Honda Fit
I've got the AWSC-01 connected to the HDCC-02 harness. The module will sense my buttons for setup but I cannot get it to work with the head unit. The head unit will detect a button press when the module ends it's setup mode on boot though. I've got it hooked up as described using the wires through the HDCC-02 harness. I even tried grounding each wire and it didn't make a difference.
According to another user they had to buy a $100 adapter to get it to work. I really don't want to pay $100 for steering wheel buttons.
Help would be appreciated.
2014 WRX l, no nav, bluetooth.
So my Metra harness did not come with steering wheel pins (4, 13, 14) can I just bypass the harness and hook it up straight from the A6 to the cars wires?

Is this how I can get steering wheel controls to work?

Any help you guys can provide would be invaluably appreciated. I’ve been racking my brain over this for months now with no solution. I really want steering wheel controls in my car.
I have a 2009 Mazda 6. I have connected the head unit using this harness- https://aerpro.com/chmz6c#
Can I use this patch lead (https://frankiesautoelectrics.com.au/aerpro-aplrnpl-type-c-self-learn-patch-lead/) and connect it to the other side of the SWC module/CANBUS? I’m guessing I’d have to wire the key1 and key2 wires to the key1 and key2 wires coming out of my headunit.
Is there anything/something else I have to do?

Nissan Murano MK1 - how to connect steering wheel controls without adapter

Hi guys,
After couple of weeks research I was lucky enough to find a simple way of making my steering wheel controls work with my aftermarket Android head unit.
There are 3 white connectors - see pic 1.
The one in the background is a 16 pin connector and this is where we do the following - from the cable that came with your aftermarket unit (see pic2):
1. Connect GROUND to Green/Black cable
2. Connect KEY1 to Green/White cable
3. Connect KEY2 to Green or Lime cable
4. Start the car and configure steering wheel controls inside your settings.
Voila, you now have steering wheel controls. I know this works on European models (all gen1).
Enjoy!

Eonon 10.1 inch universal double din steering control

Just bought one of these eonon q03pro units to put in my 2006 mercedes c180 (W203), its a universal unit not car specific, to replace a failed other chinese unit(8 core 8667 chip based unit). I have tested it today but not fully fitted as waiting for facsia kit to arrive.
My last unit was car specific with dedicated wiring harness and canbus for steering controls, this one only came with a standard ISO connector and I have a dedicated mercedes wiring harness coming with the facsia kit, however having a day off I decided to try powering up with the harness from the old 8667 unit, it powered up ok but the steering controls will not work. I have been told Mercedes don't use the resistive control method, you can't program wheel controls like that via the key wires. You would need to use the high/low wires and select your Mercedes model in the advanced Canbus options
robfox1975 said:
Just bought one of these eonon q03pro units to put in my 2006 mercedes c180 (W203), its a universal unit not car specific, to replace a failed other chinese unit(8 core 8667 chip based unit). I have tested it today but not fully fitted as waiting for facsia kit to arrive.
My last unit was car specific with dedicated wiring harness and canbus for steering controls, this one only came with a standard ISO connector and I have a dedicated mercedes wiring harness coming with the facsia kit, however having a day off I decided to try powering up with the harness from the old 8667 unit, it powered up ok but the steering controls will not work. I have been told Mercedes don't use the resistive control method, you can't program wheel controls like that via the key wires. You would need to use the high/low wires and select your Mercedes model in the advanced Canbus options
Click to expand...
Click to collapse
Hi, as you changed device , you must set also model for wheel controls via canbus settings in factory settings. It must work.
Sometimes controls must be set afterwards, depends on the canbus box (if it is SIMPLE SOFT, HIWORLD or RAISE canbus) that you installed. You have to shift between canbus settings of various car models in order to work. If you have online update for canbus controls update via internet.
Thank you will try that, maybe trial and error but I thought there would be a way to make it work, as it was from a previous unit set for W203 Mercedes c class. This is my 3rd android unit in the car so hopefully this one will work

Categories

Resources