Yoga tab 3 pro dead :( - Thinkpad Tablet General

After an update, I get an error message... I restart the tab, and shows lenovo logo with an orange progress bar, that interrupts before ends.
Now, The screen is totally black, pc dont detect the tab... If i long press power button I get a vibration fro tab, and the led of power button light for a few seconds, then nothing.
I try to boot in dnx mode, fast boot... all things, nothing. Black screen
some advice?????
thanks

Please see this guide I wrote some days ago at https://forum.xda-developers.com/th...mprehensive-guide-to-lenovo-yoga-tab-t4082253
Even if you can't see in your screen you are in DNX mode, you may be there, and you only need to be there for seconds. Follow the instructions for flashing firmware using the Intel tool. You may need to come back to Lollipop, but that is a good start.

CENTSOARER said:
Please see this guide I wrote some days ago at https://forum.xda-developers.com/th...mprehensive-guide-to-lenovo-yoga-tab-t4082253
Even if you can't see in your screen you are in DNX mode, you may be there, and you only need to be there for seconds. Follow the instructions for flashing firmware using the Intel tool. You may need to come back to Lollipop, but that is a good start.
Click to expand...
Click to collapse
bu any pc detect it, i test in some computers, and nothing

dskmusic said:
bu any pc detect it, i test in some computers, and nothing
Click to expand...
Click to collapse
Ah... I haven't wrote about it but some devices (even some Lenovo ones) can pull an update.zip file from an external sdcard. You can research about this update method since they don't require a PC connection, other than that, consider going to tech support.

CENTSOARER said:
Ah... I haven't wrote about it but some devices (even some Lenovo ones) can pull an update.zip file from an external sdcard. You can research about this update method since they don't require a PC connection, other than that, consider going to tech support.
Click to expand...
Click to collapse
yes, but your method needs to use the tab... I cant, black screen and probably tab off!!!

dskmusic said:
yes, but your method needs to use the tab... I cant, black screen and probably tab off!!!
Click to expand...
Click to collapse
The update.zip file method just needs to detect the SD card and pull the update file. I did not wrote about that method and above all, is not mine. It's just an idea for you to explore, I wouldn't know if it will help.

CENTSOARER said:
The update.zip file method just needs to detect the SD card and pull the update file. I did not wrote about that method and above all, is not mine. It's just an idea for you to explore, I wouldn't know if it will help.
Click to expand...
Click to collapse
how its work?¿

Related

[Solved] Mystery bricked tablet. Black "android systems" screen

I bought an Acer a500 tablet a few days ago not knowing how broken it is.
After loads of research and attempting different techniques I still haven't had any progress.
The software issue:
When booting up the tablet, it goes to the black screen with "android system" at the top and power off/ shutting down in the middle of the screen.
Fixes I've tried:
1.
Since I don't know anything about what operating system is on this tablet, I have been blindly flashing different "stock" (from Vache) versions of HC.
--The android logo with gears shows up, the green bar loads but freezes when it gets 1 cm away from finishing.
--After turning off the tablet and booting it up again, "updating bootloader shows up on the upper left hand corner of the screen. Then a message pops up saying "apk installer: all pre processes complete". Then it returns to the black screen.
2.
The tablet will not go into apx mode (using the reset botton at the bottom).---Fixed. I didn't execute the steps properly. Apx mode works fine.
3.
I plugged the tablet into an older windows laptop and the computer could not install the correct drivers to sync with the tablet. Again also my lack of knowledge. I installed drivers from Acer.com
4.
These two guides seem to be exactly what my problem is but I can't seem to make sense of them:
http://forum.xda-developers.com/showthread.php?p=24531880#post24531880
http://forum.xda-developers.com/showthread.php?t=1572622
This is as far as I've gotten.
Other complications:
--The battery is dead. I have to use it while plugged in by the charger.
--Most of the thread that I have looked at use Megaupload as the source of downloading their files.
--The original owner of the tablet will not help me out. As I stated before, I don't know what version android OS was on here before it was bricked and on top of that the original owner won't answer my questions. As far as I know though, this tablet is not rooted or has anything "non-OEM" installed in it. The story goes that this tablet was bricked when the owner tried to "update" it. Before that, it was functioning perfectly.
-----It looks like Darvis is having the same issue and frustrations I'm having but reading his threads makes me think that this tablet is a dead end.
http://forum.xda-developers.com/showthread.php?t=1427983&page=4
http://www.androidtablets.net/forum...32467-please-help-me-unbrick-my-iconia-5.html
If someone could point me in the right direction toward fixing this tablet, I would appreciate it very much.
Thank you for reading my Thread.
KiwiN said:
http://forum.xda-developers.com/showthread.php?t=1572622
Click to expand...
Click to collapse
First off......I hope u didn't pay much for the tablet.
Secondly the guide above looks pretty straight forward but maybe this is one of the ones that has files at megaupload?
I know that the ra recovery and timmydean's files are accessible as I have downloaded both of them.
Maybe someone who has done this previously will chime in and get you the other file if it is indeed unreachable.
Sent from my A500 using xda premium
I would suggest trying to connect the tab to a Windows 7 PC after installing the USB drivers from ACER. Then check if your device appears in the device manager. As long as you have its UID you can flash the tab from the PC with one of the EUU tools - check my signature on "how to revert to 3.0.1" or TimmyDean's thread which offers an EUU with rooted HC 3.2.1 (it's linked in my thread as well).
How exactly did you try to get into APX mode?
p.s. I have the EUU files if you can't access them from the threads links. I can send them to you.
getting into apx mode
When I perform the steps (hold reset + power for 3 secs then release power); the tablet turns on as it usually does. It goes to the Acer screen, then android and back to the black home screen. My computer responds by saying that it is "installing drivers" but it "fails to install drivers". At the same time I have the DND.exe open and it does not recognize my tablet.
I'm trying to follow the instructions from the root 3.2.1 v4 file.
I can't perform the first step where it instructs me to turn on Usb debugging. The problem is that I can't open the settings by clicking the clock. Nothing happens.
I realize that one complication of my tab is that it will not charge. The battery power is below 15% so none of these fixes might not be effective for me. That might be the ultimate problem?
CyaN1de-
I paid $100 for the tablet. As of this moment I feel like I paid too much.
Thank you both for you quick replies. I have to say that most of the problems that I'm having is because of my lack of experience but I'm learning. I hope I fix this tab soon.
if this dont fix it, i'll give you what you paid for it;0
someone posted a while back that a hard reset fixed the android systems screen error
not sure where you're at now but no harm in trying it
Try using hard reset:
1) Turn off your tablet,
2) Rotation lock s to your left;
3) Press Vol+ (which is next to rotation lock) and power on simultaneously
4) As soon as the tablet vibrates you can release the power on button and you
should start to switch rotation lock left and right till you see
Erasing Userdata...
Erasing Cache...
Vol+ is still pressed;
5) The tablet starts to format
6) Your tablet will be as clean as it can be.
Thanks for the suggestion but I didn't accomplish anything by hard resetting it. I've done this many times and nothing has changed.
I haven't given up on unbricking this tablet yet and even though it's frustrating I'm learning from the process. If I decide to sell it, I'll contact you Dibb.
KiwiN said:
.....
When I perform the steps (hold reset + power for 3 secs then release power); the tablet turns on as it usually does. It goes to the Acer screen, then android and back to the black home screen. My computer responds by saying that it is "installing drivers" but it "fails to install drivers". At the same time I have the DND.exe open and it does not recognize my tablet.
Click to expand...
Click to collapse
i've seen the 2 methods u described but i've not seen anyone else have success with it apart from the OP'ers - seems OTT to me but hey if it works for ya...
I've used timmydeans method ALOT on HC it never failed to work and that includes reverting back to HC from ICS - if it doesnt work for your issue then id be tempted to use blackthund3rs APXFlash Tool and civato's HC_ICS_Bootloader zip to flash a new bootloader and rom package on yr tab - but for the moment we'll run with td'sv4 - if drivers fail to install then believe me, its a good sign
try this:
I know you-ve probly done it but u need to do it again:
reboot everything, then reinstall acer drivers (yeh i know)
fire up ya tab but dont connect to yr pc just yet -as you said you
doubt usb debugging in enabled so we'll try another way around it
run the prgb20.exe it will scan for the new image but not find it becos youre disconnected...thats good....
after maybe 5 -7 minutes of scanning for the new image - it will show a
window "cannot detect yr iconia tab"
and instructions for getting into apx mode - go ahead connect usb put the tab into apx BUT don't click next until....
the drivers will try to install, dont let windows search but let me choose
(off memory) choose device and adb or android ph should show up here
the acer boot/recovery drivers should install...maybe even under USB Controllers
once they do and only when they do click next to put tab into:
acer download mode.......
as i said this is worth a go,,,,how about the update.zip have u tried that.....
else the only other way i know is apx flash....ya still need to get into apx
mode and if u cant then ???? sometimes youll try something over and over
and then out of the blue it will work...you'll swear you never did anything different , it jsut worked this time.....
hope you find some joy
Thanks Dibb for your words of wisdom. I've put it aside for now but I'm going to pick it up in the morning.
As addition to what dibb_nz said - Windows 7 would do the trick - I'm almost 100% sure you'll be able to connect in APX mode with the drivers properly installed. Then use one of the EUUs.
Drained battery really looks like the ultimate problem now because as far as I know you cannot charge the tab in APX mode - haven't tried that. Eventually I would suggest to crack the tab open, remove the battery and charge it somewhere - I don't know alternative ways but...may be another tab or you own charger with proper connector ...
http://www.youtube.com/watch?v=xvXihNIdQ1M
p.s. 15% power ... seems enough to flash through the PC...but who knows - don't waste them and get everything you need before starting the procedure.
no probs m8 hope u have better luck tomorrow
if u wanted to try the EC method i have those files if you want them
good luck m8
dibb_nz said:
if drivers fail to install then believe me, its a good sign
try this:
I know you-ve probly done it but u need to do it again:
reboot everything, then reinstall acer drivers (yeh i know)
fire up ya tab but dont connect to yr pc just yet -as you said you
doubt usb debugging in enabled so we'll try another way around it
run the prgb20.exe it will scan for the new image but not find it becos youre disconnected...thats good....
after maybe 5 -7 minutes of scanning for the new image - it will show a
window "cannot detect yr iconia tab"
and instructions for getting into apx mode - go ahead connect usb put the tab into apx BUT don't click next until....
the drivers will try to install, dont let windows search but let me choose
(off memory) choose device and adb or android ph should show up here
the acer boot/recovery drivers should install...maybe even under USB Controllers
once they do and only when they do click next to put tab into:
acer download mode.......
hope you find some joy
Click to expand...
Click to collapse
So I went through all these steps and the TD's V4 tool finishes updating the tab. But then it continues to the same black, android systems screen. And afterwards the tablet won't connect with the computer.
I am currently downloading the update.zip so i'm going to see if that will work.
KiwiN said:
So I went through all these steps and the TD's V4 tool finishes updating the tab. But then it continues to the same black, android systems screen. And afterwards the tablet won't connect with the computer.
I am currently downloading the update.zip so i'm going to see if that will work.
Click to expand...
Click to collapse
do u get on yr tab the big 'PASS' in white leetters or "entering download mode" at all???
think we're beyond update.zip if EUU failed but you can try it -
you can get to apx which is a start - getting a new boot/recovery image on there is the main priority I think...as i posted earlier i've only ever seen a fix for this problem work for 2 people, so on new ground here....
But anyway check out the APXFlash method/walkthru in my sig....all the info is in there and the links to the required files ....do we know if you're on HC or ICS B/L????
I got the word pass; now using recovery mode to flash a rom.
not sure which bootloader I have.
I am using:
Acer_A500_7.006.01_COM_GEN2: http://vacheandroid.com/files/Acer_...1_COM_GEN2.zip
But after it says install from sdcard complete it also give me the message:
E: Can't mount/ dev/block/mm....
E: Can't mount Cache: recovery/log
E: can't mount open cache: recovery/log
E: Can't mount /dev/block/mm...
found this:
dibb_nz said:
yes if you're talking about the stock roms from vaches thread, you need the full rom package - you cant just use an 'update' package as they need a full rom to work properly....
for instance my original HC3.2.1 Stock build is 7.014.15_COM_GEN1
and theres no FULL Rom for 3.2.1, so i have to use the HC 3.2 FULL instead
.....Acer_A500_7.006.03_COM_GEN1.zip
Once flashed, thankfully I recieve the 2 small OTA Updates to get up to 3.2.1 again
Another couple of days the ICS OTA d/l'ed and installed with no probs....
is that clearer or am i making things worse????
Click to expand...
Click to collapse
What I've learned from this whole process is that all of the obstacles I'm facing are due to my lack of knowledge. Thanks for sticking with me Dibb. I can't thank you enough.
KiwiN said:
When I perform the steps (hold reset + power for 3 secs then release power); the tablet turns on as it usually does. It goes to the Acer screen, then android and back to the black home screen.
Click to expand...
Click to collapse
I could never get mine into apx mode with the usb cable plugged in. So try that if you haven't. And it is literally hold reset, then press power, without letting up on the reset, release the power button after 3 seconds (use a watch or timer!) then one more second before you release the reset... It does work, but the timing has to be close. It must have a tenth of seconds or less tolerance. Very picky... I've done it on 2 different a500s so far and I am heading to do another tonight. If it doesn't work I'll be right back!!!
KiwiN said:
I got the word pass; now using recovery mode to flash a rom.
not sure which bootloader I have.
I am using:
Acer_A500_7.006.01_COM_GEN2: http://vacheandroid.com/files/Acer_...1_COM_GEN2.zip
But after it says install from sdcard complete it also give me the message:
E: Can't mount/ dev/block/mm....
E: Can't mount Cache: recovery/log
E: can't mount open cache: recovery/log
E: Can't mount /dev/block/mm...
found this:
What I've learned from this whole process is that all of the obstacles I'm facing are due to my lack of knowledge. Thanks for sticking with me Dibb. I can't thank you enough.
Click to expand...
Click to collapse
Hi m8 Hwya goin - just got home - what's the lay of the land???
Holey motley we just had a good shake....thort was gonna carry on thank fk it stooped, phew, just been awhile since we had one like that, scary
Crikey just as I finished typing "....land"
Back to more important matters..... whr u at m8????
None of the roms I've tried to flash go to completion. I'm stuck at trying to flash different roms from recovery mode. Not much luck with what I've tried but I'm going to try more before I give up.
Are there any particular roms I should try more than once?
Or why am I getting the "error" messages stated earlier?
KiwiN said:
None of the roms I've tried to flash go to completion. I'm stuck at trying to flash different roms from recovery mode. Not much luck with what I've tried but I'm going to try more before I give up.
Are there any particular roms I should try more than once?
Or why am I getting the "error" messages stated earlier?
Click to expand...
Click to collapse
recovery mode???
u need a new boot and recovery image on that thing
the HC EUU based flash arent working even tho u got a PASS on screen after TDv4
So HC based methods arent up to it. You need nvflash/fastboot.
We need ICS with the unlocked bootloader it has access to another level below where HC worked because HC b/l is and always has been locked down.
If ICS cant fix it, I have no idea what will and my offer to buy is off the table!!!!
check out civatos guide and ready yourself for nvflash via zip files in that post or blackthund3rs APXflash tool, with a complete tutorial for using it, all links in my sig.
good luck
Just to chime in with a tip on getting google drivers to work.
When getting any device not recognized, or driver error, generally I go into windows device manager, select the unknown or offending device, update driver, only I choose which driver to use, and ignore the error message where it says "may not be compatible with your device", and use it anyhow.
I get that occassionally when swapping back and forth between devices.
Also, battery not charging and display errors, are usually a sign of EC Power control. So you were on the right track about that. Once you get a rom up and running, if the batt don't charge, then there are some EC flash's you can do from CWM.
Back at it again using BT's nvflash tool. And tablet is still bricked.
I've tried a few different bundles and none allow me to operate the tablet. Everything goes smoothly and I get "pass" at the end of the process. When I go to reboot the tablet, it gets stuck at the black start up screen.
Found another lead: http://forum.xda-developers.com/showthread.php?t=1579490
Sounds like he was in the same situation as I am but has a bit more skills and knowledge dealing with problem solving.
You say you were able to flash roms. So apparently recovery is working OK. Have you tried flashing civato's flexreaper? It has code that will detect whether you bootloader is HC or ICS. You may just be flashing a rom that doesn't match your bootloader... I know I'm jumping into the middle of this, but it's just a thought.
Also, when you did the hardware reset with the rotation lock switch did you get the confirmation that it was, in fact, being wiped?
Failing all that, I'd be willing to take it off your hands for spare parts...
Sent from my A500 using Tapatalk 2

[Q] unbrickable ideos x5?

Hi, I think this is my first post here. Anyway, here the question:
I have an Ideos X5 (not pro), it is bricked. So far, I have followed instruction for recoveries from several threads, but none of them worked because in my phone:
there is no boot screen
there is no pink screen
there is no logo
there are no images of any kind (screen wont even turn on)
it only vibrates when I plug it into my computer
Also *sometimes* the buttons light up and when this happens windows detect a new USB device, but after I while it dissapears again. Also, this happens only with the battery on.
The phone became bricked after I followed instructions to revert back to froyo from gingerbread (wifi wasn't working). All roms were originals from Huawei.
So, any suggestions??
Thanks in advanced.
I had a problem like you.I have deleted amss.mbn file because Huawei locked pink screen, it was bricked But i wasn't so patience enough, i sent my phone to technical care.But here are the answers, try it with caution:
shuiyunxingzuo said:
Hi
Space is not enough to flash any ROMs;
Bootloader is locked,you could not edit that sector.
So is there a special ROM that is very small and allows to edit the bootloader?
Here is the MINI ROM:
http://www.mediafire.com/?7c33h84a974va28
Flash it than edit the bootloader~
NOTICE: I format the whole sector ,and the file including IMEI was missing
'Cause I don't know how to edit recovery or other system files like .mbn,
so just delete the abnormal big file and you would be able to flash any ROM s
Click to expand...
Click to collapse
xmsnx said:
Yes!!!! My phone works"!!!!!!!
Ok here's what I did
Download mediafire.com/?1hbk6n46hgamyt6
Unzip it, and find UPDATE.APP
Put UPDATE.APP in a dload folder and upload to empty sdcard.
Put sdcard in phone, and hold vol+/- and power and flash it.
After phone has restarted pull battery.
Download http://www.mediafire.com/?6hrfz36b8e2vw87
Unzip and copy the dload folder to empty sdcard.
Hold vol+/- and power and flash it.
After it fails near the end or if it restarts then pull battery.
Download a rooted boot.img and a clockworkmod recovery.img (got both mine from links at modaco)
Attach phone to PC in pink screen mode and delete the boot.img and recover.img files.
Upload the downloaded root.img and recovery.img to image folder in phone.
Download any custom rom from XDA, I used http://forum.xda-developers.com/showthread.php?t=1475687 and upload it to sdcard
Pull battery.
Hold vol+ and power and go into clockworkmod, wipe everything and flash the custom rom!!
Good luck!
Click to expand...
Click to collapse
Tried taking off the battery for 10 seconds and after that inserted USB into computer (without battery)? Also try to take off battery and insert USB to wall-charger.
The buttons lighting up could be our way out, but if it only stays there for a couple of seconds it doesn't help. Can you see what Windows detects?
Hi again,
thanks for answering.
None of your suggestions worked anyway, because it won't even load anything from the sdcard, it just makes a short vibration and nothing more.
I managed to get the lights on again, but windows didn't show what kind of device it was, maybe because it's already installed but I'm not sure which usb device is it (windows did make a sound though, like "device is connected" sound). Also I noticed there's a red led blinking near the speaker, does that mean anything?
Anyway, tried to flash while the lights were up but it did nothing, and after two minutes the went off again.
Thanks again for your suggestions.
I connected the phone to my laptop with ubuntu, and despite I cannot do anything with the phone, there are two devices created in /dev: hiddev0 and hidraw0. Is there a way to flash the device using any of those files?
thanks again.
Worth a try on this post : Here
It is fried then
Try mounting those two devices, is there any file system recognized? It might not be bricked, but this is an issue probably nobody has had yet. Send it in for repair if it is still within warranty.
Important question: How did this even happen?
XphX
XphX said:
Important question: How did this even happen?
Click to expand...
Click to collapse
auxorro said:
The phone became bricked after I followed instructions to revert back to froyo from gingerbread (wifi wasn't working). All roms were originals from Huawei.
Click to expand...
Click to collapse
Sent from my U8800 using Tapatalk 2
Hi,
thanks for all the help.
Sadly nothing works with this phone, I tried mounting and dd from the devices but nothing happens.
I guess I'll send it for repair (hope it's still within warranty)
Anyway, thanks again for all the suggestions.
Bye!!
auxorro said:
Hi,
thanks for all the help.
Sadly nothing works with this phone, I tried mounting and dd from the devices but nothing happens.
I guess I'll send it for repair (hope it's still within warranty)
Anyway, thanks again for all the suggestions.
Bye!!
Click to expand...
Click to collapse
If the phone wasn't rooted, then it is still within warranty

How to unbrick your tablet!!!!!!!!!!!!!

**NEW GET THE TWO ICS ROMS http://forum.xda-developers.com/showthread.php?t=1633907**NEW
first download all three of the files
open the acer decrypter and run it
now where select the input file, should be in downloads folder(leave the output folder
remove the sd card from your acer a500 and put it into some kind of device that can hold an sd card and plug it in
select usb mass storage device or disk drive on your device
go into your download and open the DECRYPTED rom
Extract the whole folder to desktop
now copy all of that to the sd card through your phone/device
shut off iconia tab
hold power button and VOL- until it says entering recovery mode
now you should see a green android guy with gears in him
DO NOT TOUCH ANYTHING
hope this worked, it worked for me!!!!!!!!
*************if the first rom doesnt work do the same steps for the second one, be sure to delete the first one off your sd card*********
any input from other users,... success?.....failure?.
just think this is good info..."if correct" i wouldn't mind having this knowledge if it works
Yes, it works. I did it a few times to unbrick my A501 this week.
I had broken my recovery also, so the EUU version helped in that case, but at least I got a clean start to go to another ROM.
hope this has worked if it has please hit the thanks button
When you say SD Card, do you mean the external SD card, or the onboard card? I need to do this, but my tablet isn't recognizing my external SD card. Is there another place for me to put the files, where the tablet will access them?
You need to us ethe external one, in cwm mount SD card
lol im such a dope ive actually used the EEU rom to ix the verified boot failed error when i first loaded flexreaper.....lol mind becoming more cluttered then my pc.
For a cluttered PC I would recommend advanced system care hahahahhahahahha and for your head a good run or bike ride or even a nap
jnktechstuff said:
For a cluttered PC I would recommend advanced system care hahahahhahahahha and for your head a good run or bike ride or even a nap
Click to expand...
Click to collapse
lol tried all of the above no help
Hi,
just a question, why download the 2 ICS ?
one of the 2 is enough ? Which one to choose ? What is the difference ?
Thanks
Only boots to recovery
So i have been using the flexreaper rom and i tried installing the newest revision and when it all finished (i took all the proper wipe steps before installing) and now my tablet only goes to the acer screen... I have tried other roms, but no dice. I am going to see if this works.
Great Job!
You did a great job with this post, It works flawlessly
Thanks!
My Iconia does not even boot, all I have is a black screen with the power light on. Will this method work for me?
Try pressing the power button and volume up at the same time and if you see the green android with gears, you are good to go.
DROID RAZR MAXX /DROID BIONIC
Help
jnktechstuff said:
[*]first download all three of the files
Click to expand...
Click to collapse
Acer decrypter is one of the files, but what are the other two? How are you supposed to know which two to download? I'm bricked and can't check in Settings > about like the thread says...
there is the decrypter and the two ics roms,put both on your sd card just in case the other one doesnt work
JM1084 said:
My Iconia does not even boot, all I have is a black screen with the power light on. Will this method work for me?
Click to expand...
Click to collapse
you are stuck in a apx mode it is solved by getting this its called afterota:
https://hotfile.com/dl/160313682/62f94d6/Afterota_v1_09.zip.html
there is a section that says get out of apx mode
MAKE SURE YOUR ACER DRIVERS ARE INSTALLED!!!!!!!!!!!!
jnktechstuff said:
you are stuck in a apx mode it is solved by getting this its called afterota:
there is a section that says get out of apx mode
MAKE SURE YOUR ACER DRIVERS ARE INSTALLED!!!!!!!!!!!!
Click to expand...
Click to collapse
I have managed to get it out of APX mode and flashed Lightspeed V8 ICS bootloader and recovery. Have tried to flash multiple ICS roms but it hangs at "Booting primary kernel image" with every one. Any possible ideas?
Sent from my ADR6400L using Tapatalk 2
you need to re-install your bootloader, all the roms now require the ics bootloader
multor said:
Hi,
just a question, why download the 2 ICS ?
one of the 2 is enough ? Which one to choose ? What is the difference ?
Thanks
Click to expand...
Click to collapse
you need both just in case one of them doesn't work, it saves you time!!

Amazon Blu R1 HD [Firmware] [Restore] [Unbrick] [Unroot]

How to Firmware Restore the Amazon Blu R1 HD
With the Help of many of you at XDA we have put together a working scatter file and I have pulled the Firmware from the device so that we can now restore this phone.
View attachment 3826922
STEPS TO RESTORE DEVICE AND BE ABLE TO HAVE ADS AND OTA UPDATES WORKING AGAIN
1. Download SP_Flash_Tool_BLU_R0010UU_V6.4_Firmware.zip
2. Extract the SP_Flash_Tool_BLU_R0010UU_V6.4_Firmware.zip to your desktop. Note 7zip is great to extract files.
3. lauch Flash_tool.exe
4. select scatter-loading and browser to load MT6735_Android_scatter_R1_HD_Amazon.txt
5. click download button to start.
6. now plug your phone into the computer. to boot the device to preloader and start the flash. You can do it two ways: 1. power off the phone and flash will start or 2. From a powered off stat power on the device while plugged into the computer. either way will start the sp flash tool.
7. once the flash is complete you can unplug the device and reboot it with the power button. Congrats you have fully restored your Amazon Blu R1 HD. Bonus you have also enabled bootloader unlocking if you want it.
Tutorial Video with all the steps need to restore.
NOTE: This has been fully tested on the Amazon R1 HD 16GB model but should work on the 8gb also.
You're the man!
Hi, I keep getting this error:
BROM ERROR: S_DL_GET_DRAM_SETTING_FAIL(0x13BE)
[EMI]Obtain DRAM Failed!
[HINT]:
Please check your load matches to your target which is to be downloaded
Do you have any idea how to fix it? Thanks.
Dude this doesnt work for me.
When I plug in my phone, a popup from Flash tools comes up saying, "PMT changed for the ROM; it must be downloaded."
Then what?
johnsmithsir12 said:
Dude this doesnt work for me.
When I plug in my phone, a popup from Flash tools comes up saying, "PMT changed for the ROM; it must be downloaded."
Then what?
Click to expand...
Click to collapse
EDIT - DO NOT USE THE DOWNLOAD+FORMAT MODE EVER ON THE R1, IT WILL RESULT IN A BRICK, IT MAY WORK ON OTHER MTK MODELS, BUT EXPERIENCE HAS SHOWN IT WILL BRICK THE R1 HD!!!! DOWNLOAD ONLY IS THE ONLY SAFE METHOD!!
Occurs if the names or addresses of the blocks in the scatter differ from the table inside the phone (PMT).
Thats not good, i suggest maybe checking the scatter file making sure its not currupt... Or try the following alternate solution....
http://forum.xda-developers.com/r1-hd/how-to/guide-convert-to-prime-rollback-ota-t3432499
This also seems to be a solution,but perhaps more dangerous last ditch effort maybe?? The video is for a different MTK SoC, but from what what im reading it's the same technique across the MTK lineup..
Perform at your own discretion, not responsible for bricked devices....
kal250 said:
Occurs if the names or addresses of the blocks in the scatter differ from the table inside the phone (PMT).
Thats not good, i suggest maybe checking the scatter file making sure its not currupt... Or try the following alternate solution....
http://forum.xda-developers.com/r1-hd/how-to/guide-convert-to-prime-rollback-ota-t3432499
This also seems to be a solution,but perhaps more dangerous last ditch effort maybe?? The video is for a different MTK SoC, but from what what im reading it's the same technique across the MTK lineup..
Perform at your own discretion, not responsible for bricked devices....
Click to expand...
Click to collapse
I rooted my phone via this method: http://forum.xda-developers.com/r1-hd/how-to/twrp-how-to-root-t3425677
Keep in mind, only "recovery" was checked and nothing else.
yujiba said:
Hi, I keep getting this error:
BROM ERROR: S_DL_GET_DRAM_SETTING_FAIL(0x13BE)
[EMI]Obtain DRAM Failed!
[HINT]:
Please check your load matches to your target which is to be downloaded
Do you have any idea how to fix it? Thanks.
Click to expand...
Click to collapse
Try this: http://onlinejobwithoutanyinvestment.com/sp-flash-tool-errors-fix-brom-error/
Format your phone, but not the bootloader, and then try reflashing
We're seeing reports of this bricking phones. If you are considering trying it, don't! If you have bricked your phone, please join our Hangout right here and cooperate with us to find the cause of the brick and a way to unbrick it!
Join the conversation on Hangouts: https://hangouts.google.com/group/Q5wGs6508l1rqGng2
Sent from my LG G4 using XDA Labs
ColtonDRG said:
We're seeing reports of this bricking phones. If you are considering trying it, don't! If you have bricked your phone, please join our Hangout right here and cooperate with us to find the cause of the brick and a way to unbrick it!
Join the conversation on Hangouts: https://hangouts.google.com/group/Q5wGs6508l1rqGng2
Click to expand...
Click to collapse
The format method, i stumbled upon, i just added as a last ditch effort, I'm not sure whats causing the errors to begin with. The scatter addresses all still match the block addresses mapped in the new OTA, so that theory is shot, im not sure what else could be going on.
If SPFT WON'T FLASH
1. Power off your phone.
2. Hold the power and volume up buttons then choose "recovery" from the menu that shows up.
(volume buttons = up/down, power button = ok/select)
3. Now choose power off.
Doing the above makes sure your phone is COMPLETELY shut off, windows can find your phone, and SPFT will be able to flash it.
I believe that, when you use "power off", from within android, it actually puts the phone in some type of suspend or hibernation mode. I say this because you can hit the power button and it will boot very quickly after powering off within android, but from recovery it takes longer to boot. This was the case with mine.
Your only other option is to let the battery completely drain, then try SPFT.
SHOUT OUT TO ALL THE GUYS THAT ROOTED THIS SUCKER AND UNLOCKED IT! GREAT WORK! ???? :good:
burnanator said:
If SPFT WON'T FLASH
1. Power off your phone.
2. Hold the power and volume up buttons then choose "recovery" from the menu that shows up.
(volume buttons = up/down, power button = ok/select)
3. Now choose power off.
Doing the above makes sure your phone is COMPLETELY shut off, windows can find your phone, and SPFT will be able to flash it.
I believe that, when you use "power off", from within android, it actually puts the phone in some type of suspend or hibernation mode. I say this because you can hit the power button and it will boot very quickly after powering off within android, but from recovery it takes longer to boot. This was the case with mine.
Your only other option is to let the battery completely drain, then try SPFT.
SHOUT OUT TO ALL THE GUYS THAT ROOTED THIS SUCKER AND UNLOCKED IT! GREAT WORK! ???? :good:
Click to expand...
Click to collapse
Never occurred to try that, curse this trend of non removable batteries anyways -_-
kal250 said:
Never occurred to try that, curse this trend of non removable batteries anyways -_-
Click to expand...
Click to collapse
Yup. That's why i tried it. This is the first phone i have had with a non-removable battery.
johnsmithsir12 said:
Dude this doesnt work for me.
When I plug in my phone, a popup from Flash tools comes up saying, "PMT changed for the ROM; it must be downloaded."
Then what?
Click to expand...
Click to collapse
I just saw your other thread you started
http://forum.xda-developers.com/r1-hd/how-to/question-restoring-to-factory-default-t3440059
And now I see why you had this error. You have the 8gb version not the 16gb. So this method uses the wrong scatter file for you phone. Please update the forum if you still have the phone and need assistance. There are some commands that you can run in adb to see the partition sizes and then with that the scatter file can be adjusted for your phone
sorry for being off topic here but i really need to know if its possible to unlock more 4g bands , in my contry they don't release the infomation of what bands the providers work so its a guessing game, since i got this phone i purchased the 4g sim card , even with the band 12 update still stuck at 3g , even with proper 4g apn still stuck at 3g wich i came to a conclusion that the 4g bands from the Blu R1 HD are not the same as my providers...in conclusion can it be done ( open up more bands to see wich band will get me the 4g) and if so please explain to me how i can do so please.
This worked for me, but I had to factory reset after because OTA was still detecting root.
Help me!
hello, I do all the steps but remains in the logo and reboots
THIS DOES NOT WORK WITH 8GB/1GB version :'(
Hello,
I just want to unroot my Blu R1, what should I do?
DOA Bricked
Any hope for an R1 which will now not even power up?
This will not work on any of the latest versions. My model is a 2GB/16GB - I was on Coltons root and tried this to go back to stock with my phone now stuck in boot loop.
Do not use this method.

Lenovo Tab M10 FHD Plus (X606f) won't power on after flashing older ROM

I'm flashing my new Lenovo tablet with Android 9 (so I can flash it later with Ubuntu Touch) and after SP Flash tool finished flashing
tablet won't power on. The power button does nothing and holding volume down + power button does nothing either.
The battery isn't dead so I'm trying to figure out why the tablet won't come on if older ROM is on it.
I had no error outputs during the flash.
This is the ROM I flashed https://mirrors.lolinet.com/firmwar..._Gen/TB-X606F/TB-X606F_S300007_200923_BMP.zip
Any suggestion as to how to get it to work again ?
I don't think you can downgrade these. You may need to completely wipe and reinstall the ROM.
ldeveraux said:
I don't think you can downgrade these. You may need to completely wipe and reinstall the ROM.
Click to expand...
Click to collapse
I'm using the official Lenovo's Rescue Tool but it's not helping. The tool isn't detecting the device after holding volume up + connecting.
python_rocks said:
I'm using the official Lenovo's Rescue Tool but it's not helping. The tool isn't detecting the device after holding volume up + connecting.
Click to expand...
Click to collapse
assuming windows, check that your drivers are detecting the recovery module
ldeveraux said:
assuming windows, check that your drivers are detecting the recovery module
Click to expand...
Click to collapse
Yes I'm using W10. adb is working and I've got Lenovo USB drivers installed too. What do you mean by "recovery module" ? Recovery partition inside the tablet ?
python_rocks said:
I'm flashing my new Lenovo tablet with Android 9 (so I can flash it later with Ubuntu Touch)...
Click to expand...
Click to collapse
Cool. Are you doing a Halium port for this device?
Yahoo Mike said:
Cool. Are you doing a Halium port for this device?
Click to expand...
Click to collapse
I'm not a Halium dev but I'm trying to flash the device. Me and another member of the community have our tablets dead after flushing it with supposedly Android 9 ROM. Not even Lenovo's Rescue Tool is helping now.
python_rocks said:
Yes I'm using W10. adb is working and I've got Lenovo USB drivers installed too. What do you mean by "recovery module" ? Recovery partition inside the tablet ?
Click to expand...
Click to collapse
No i mean when you connect the tablet to the pc in recovery, open Device Manager and ensure the tablet is connected with the correct driver. I'm sorry i don't know what that is offhand, but it should be different than when you connect it if the tablet was working. Sorry if it makes no sense, but i think this is what's going on.
ldeveraux said:
No i mean when you connect the tablet to the pc in recovery, open Device Manager and ensure the tablet is connected with the correct driver. I'm sorry i don't know what that is offhand, but it should be different than when you connect it if the tablet was working. Sorry if it makes no sense, but i think this is what's going on.
Click to expand...
Click to collapse
In my case there's no "connect the tablet to the PC in recovery". The tablet won't power on at all. Can't invoke fastboot nor recovery. The tablet doesn't react to any presses. Or press and holds. No nothing. The only thing I can confirm is the red LED on when the tablet is on charger.
Window's device manager is recognizing MediaTek USB driver when plugged in but that's it.
I've ran out of ideas about how to restore it hence I'm posting here.
python_rocks said:
In my case there's no "connect the tablet to the PC in recovery". The tablet won't power on at all. Can't invoke fastboot nor recovery. The tablet doesn't react to any presses. Or press and holds. No nothing. The only thing I can confirm is the red LED on when the tablet is on charger.
Window's device manager is recognizing MediaTek USB driver when plugged in but that's it.
I've ran out of ideas about how to restore it hence I'm posting here.
Click to expand...
Click to collapse
Oh i misunderstood completely! That is worse, i have no clue how to fix it...
python_rocks said:
The tablet won't power on at all.
Click to expand...
Click to collapse
If it's that dead, then it sounds like the preloader.bin is trashed.
Try this method.
There is also an older thread for older SOCs that might have some hints.
Otherwise, you might have to open up the tablet.
You could research and try the "test point" method. It involves shorting two points on the motherboard. I did something similar for the X605F (which has a QCom SOC).
I'm not sure where the test points on this tablet are. Some MTK devices don't have test points. Google "mediatek test point" for starters. If you can't find them, then maybe ask Lenovo where they are. If you find out, post a photo of the test points on here.
If you're not confident doing any of this, then send the tablet to Lenovo for repair.
Yahoo Mike said:
If it's that dead, then it sounds like the preloader.bin is trashed.
Try this method.
There is also an older thread for older SOCs that might have some hints.
Otherwise, you might have to open up the tablet.
You could research and try the "test point" method. It involves shorting two points on the motherboard. I did something similar for the X605F (which has a QCom SOC).
I'm not sure where the test points on this tablet are. Some MTK devices don't have test points. Google "mediatek test point" for starters. If you can't find them, then maybe ask Lenovo where they are. If you find out, post a photo of the test points on here.
If you're not confident doing any of this, then send the tablet to Lenovo for repair.
Click to expand...
Click to collapse
Yeah, I've ordered opening kit. I'm going in. Quite a few people got their devices working by disconnecting the battery and connecting it back. I've noticed that no matter how long the
tablet is on charger the LED stays red, it doesn't change to orange or green.
This same problem has happen to two more members of the community. Same tablet.
We had to flag that ROM as it bricks the tablet.
python_rocks said:
We had to flag that ROM as it bricks the tablet.
Click to expand...
Click to collapse
I don't have a lot of experience with the SPF tool, but could the root-cause of your problem be that you need to use a different dropdown option? See the description of the options in the unbrick guide - specifically the firmware upgrade option.
It makes sense that you want to force a full flash of low-level firmware when changing Android versions. That option seems to do exactly that.
Android 9 OS is not going to play nice with low-level firmware written for Android 10.
There might be nothing wrong with the ROM ??? ...just an idle thought.
Yahoo Mike said:
I don't have a lot of experience with the SPF tool, but could the root-cause of your problem be that you need to use a different dropdown option? See the description of the options in the unbrick guide - specifically the firmware upgrade option.
It makes sense that you want to force a full flash of low-level firmware when changing Android versions. That option seems to do exactly that.
Android 9 OS is not going to play nice with low-level firmware written for Android 10.
There might be nothing wrong with the ROM ??? ...just an idle thought.
Click to expand...
Click to collapse
Thank you for trying to help.
The flash tool doesn't do anything when I click Download and plugging in the tablet while holding the volume down button. Dropdown option was set to "firmware upgrade" as advised.
The guide suggests that it's for people who can at least power on the device. It says "switch off the phone ..." which I don't need to do since I can't even switch it on
python_rocks said:
I'm flashing my new Lenovo tablet with Android 9 (so I can flash it later with Ubuntu Touch) and after SP Flash tool finished flashing
tablet won't power on. The power button does nothing and holding volume down + power button does nothing either.
The battery isn't dead so I'm trying to figure out why the tablet won't come on if older ROM is on it.
I had no error outputs during the flash.
This is the ROM I flashed https://mirrors.lolinet.com/firmwar..._Gen/TB-X606F/TB-X606F_S300007_200923_BMP.zip
Any suggestion as to how to get it to work again
Click to expand...
Click to collapse
Did you mange to fix it?
A. Alaska said:
Did you mange to fix it?
Click to expand...
Click to collapse
You need to use a rework station heat gun or maybe a hair blow dryer might work to heat the sides of the screen to remove it.
I recommend cutting a water bottle in a square or rectangle shape then using the corner to slowly pry the screen off. After that remove the battery ribbon and hold the power bottom for 20-60 seconds to fully drain the charge.
Then recconect it and turn it on 100 percent works.
Just remember you must have the flash tool app and firmware ready in upgrade or download mode while holding down vol. It will reflash the tablet and bam will unbrick.
Just to note down my experiences here as well. I now also got into the same trouble. I tried
TB-X606F_S100015_191127_BMP.zip and also TB-X606F_S300091_201215_BMP.zip
It turns out that with these two you cannot start up the device anymore. Just as the thread-creator described. In my case pluging out and in again seems to give the SP FalshTool the chance to flash again (put it in "Download"-Mode before). So the latest firmware by today - TB-X606F_S300429_21110_BMP.zip - helped me to revive it again.
For me this is nice, but I also wanted to put Ubuntu touch on it just as described here: https://gitlab.com/ubports/community-ports/android9/lenovo-tab-m10-fhd-plus/lenovo-x606 ... unfortunately I am blocked now due to not being able to bring Android 9 on it. btw: There is no proposal on the site which firmware-version is even Android 9. I just guessed from the date.

Categories

Resources