EDIT: Problem solved!!!
I used this tutorial: https://forum.xda-developers.com/sa...very-samsung-sm-a510f-fd-exynos7580-t3314399/ to install TWRP and root my SM-A510FD on 6.0.1 . My device was rooted and working perfectly until stupid me decided to turn off "OEM Unlock" and i restarted my phone and now it says "custom binary blocked by frp lock" The only thing i can do is go to the Download mode. I tried to use Samsung Kies and Smart Switch when in Download mode but they tell me that my device is not supported. But Odin detects my device and says "Added!!". I am currently downloading the stock firmware for my device from Sammobile and i plan to flash it using Odin.
- Will putting the firmware file in the AP section of odin and clicking start work to fix the problem? (I do not care if i will loose data)
- If this will not work is there anything else that i can do? I can't take it to repair because Knox is tripped and i do not have my receipt. If my phone is bricked forever please tell me so i don't waste my time trying to fix it.
Thank you so much in advance! Any help would be extremely appreciated!!
CrystalGTX said:
I used this tutorial: https://forum.xda-developers.com/sa...very-samsung-sm-a510f-fd-exynos7580-t3314399/ to install TWRP and root my SM-A510FD on 6.0.1 . My device was rooted and working perfectly until stupid me decided to turn off "OEM Unlock" and i restarted my phone and now it says "custom binary blocked by frp lock" The only thing i can do is go to the Download mode. I tried to use Samsung Kies and Smart Switch when in Download mode but they tell me that my device is not supported. But Odin detects my device and says "Added!!". I am currently downloading the stock firmware for my device from Sammobile and i plan to flash it using Odin.
- Will putting the firmware file in the AP section of odin and clicking start work to fix the problem? (I do not care if i will loose data)
- If this will not work is there anything else that i can do? I can't take it to repair because Knox is tripped and i do not have my receipt. If my phone is bricked forever please tell me so i don't waste my time trying to fix it.
Thank you so much in advance! Any help would be extremely appreciated!!
Click to expand...
Click to collapse
Just flash stock firmware and you are good to go, if it wont boot turn it off, reboot to recovery(stock) and wipe data & factory reset, later you can again flash twrp and root but dont turn off OEM unlock.
Antonio GT-I8730T said:
Just flash stock firmware and you are good to go, if it wont boot turn it off, reboot to recovery(stock) and wipe data & factory reset, later you can again flash twrp and root but dont turn off OEM unlock.
Click to expand...
Click to collapse
Thank you so much for replying man, i was f*cking panicking! I'm gonna try that when the download finishes. Thanks again! :good:
Antonio GT-I8730T said:
Just flash stock firmware and you are good to go, if it wont boot turn it off, reboot to recovery(stock) and wipe data & factory reset, later you can again flash twrp and root but dont turn off OEM unlock.
Click to expand...
Click to collapse
What about when my j7 says custom binary blocked by frp lock(boot.img) secure fail:kernel. It will boot into recovery, and download. Factory wipe does nothing, so recovery mode is useless to me at the moment. my computer detects the phone enough to say Unknown USB device (Device Descriptor Request Failed) driver error as the label of the phone. No matter what mode I'm in. Drivers are up to date, odins good, usb port, computer, and data cords are all good. I've flashed other phones and hooked this one up to another pc to see that it says the same thing. How do I get the computer and/or odin to agree with my phone enough to pick it up as a good device?
Hi all !
I have a Samsung A8 (model SM-A800F) which was working great. I ran Kingo Root to try to install Youtube ad free. The next time I restarted it, it didn't load, and restarted in an endless loop to where "Samsung" logo appears (then restarted again). I booted into System Recovery and chose to reset to factory, but it didn't help. Then I tried flash it using Odin in Download mode. I installed the Windows drivers, downloaded the 6.0.1 firmware for Vietnam (where it was purchased), loaded the file into the AP field, and once verified clicked Start. The progress was frozen when reaching mid-way every time I tried, until it said "an error occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"...
I downloaded Smart Switch and installed in Windows, but the drivers were not able to install correctly, and failed on the component referring to the ID or something... while Modem driver was installed correctly and the phone appeared in Device Manager. Smart Switch didn't recognize my phone and said "unsupported device".
Now I cannot get the phone stay constantly ON, and the screen shuts down and loads in an endless loop, to the "Error occured" screen... When trying to boot to the ODIN Download page, it loads, I press UP for Continue, and then it again shuts down and loads to "Error Occured".
I tried to charge over night but it didn't help. It does the same thing when the phone is connected to the charger...
However it seems that by IMEI it is sill under warranty. I'm not sure if I voided it :/
Here's what the Download mode page says:
ODIN MODE
PRODUCT NAME: SM-A800F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
FAP LOCK: ON
Secure Download: Enabled
KNOX WARRANTY VOID: 0
AP_SWREV: 1
Would appreciate any help, this phone is almost new but now it's dead :/
Your warranty is not voided. Your Knox E-Fuse still intact.
Also this is for S8 not A8 forums.
Paradoxxx said:
Your warranty is not voided. Your Knox E-Fuse still intact.
Also this is for S8 not A8 forums.
Click to expand...
Click to collapse
Thanks,
I just couldn't find any A8 forum, and thought there would be more people here who can help.
Would appreciate any help on this... thanks in advance
wurlitzer99 said:
Thanks,
I just couldn't find any A8 forum, and thought there would be more people here who can help.
Would appreciate any help on this... thanks in advance
Click to expand...
Click to collapse
No worries, your phone is not dead.
Try to find a firmware that correspond to the one you got :
http://updato.com/firmware-archive-select-model?exact=1&q=SM-A800F
and use ODIN : http://dl.sammobile.com/Odin3-v3.12.7.zip
You should be good to go.
EDIT : Also for that error occurred thing, try to be faster than it by starting odin flash before it appears.
Thanks,
The problem is that neither the error nor the Odin page would stay on for more than a few seconds. Once they appear, the screen would go dark after 5-10 seconds and then the "error" page would load again (after being darks for another 10 seconds or so). So I can never have ODIN or Smart Switch connecting to the device (the drivers won't connect in Windows)... making it impossible to upload any firmware.
wurlitzer99 said:
Thanks,
The problem is that neither the error nor the Odin page would stay on for more than a few seconds. Once they appear, the screen would go dark after 5-10 seconds and then the "error" page would load again (after being darks for another 10 seconds or so). So I can never have ODIN or Smart Switch connecting to the device (the drivers won't connect in Windows)... making it impossible to upload any firmware.
Click to expand...
Click to collapse
Could you take a picture of that error ? I've never heard/seen such thing
Hi, thanks for the help !
The error is this:
http://statics1.grupoandroid.com/up...1850.jpg.d2bb2a8b77e4fba5fc6467f3d1547886.jpg
I *think* I have some direction... here's what I did/found:
- I installed Smart Switch on my Mac, and chose "Reinstall Device Driver" from the menu. Then restarted the MAC
- I loaded Smart Switch, and Chose "Emergency Software Recovery and Initialization". Then chose the "Device Initialization" tab
- Added the model number "SM-A800F" and the device's serial number (which are physically written on my device).
Smart Switch determined the firmware version to be used for initialization, as:
PDA:QC3 / PHONEG3 / CSCH4(XXV)
- Smart Switch asked to:
1. Power the device down
2. Load recovery mode by pushing Power+Vol Down+Home, then connect the device to the MAC and choose "Continue" to start the initialization...
The problem/s:
My device won't turn on at all, if I do not connect it to either the charger or the MAC (which acts as a supply source?) - which makes me think the battery is fully drained ? i.e when not connected at all, it won't power on.
But when connected to either the charger or MAC, it would bootloop endlessly. i.e it will load the "error" page mentioned above, shut down itself, reload again, shut down and so on.
(I have to mention, that when I first noticed the bootloop, I reset everything to factory settings, cleared cache etc, and it still bootlooped on the Samsung logo).
If when it shuts down during the loop, I push Power+Vol Down+Home, it would boot to ODIN recovery page, where I can push UP for the Download page, but it will still reboot and will again load into the "error" page, which will again reboot endlessly. If I take the charger off the device, it powers off and won't load with any combination of button push.
I also cannot just make it shut down when the charger is connected, using any of the possible button combinations...
I wonder:
- Is there there's a problem which prevents the battery from being charged at all ?
What's strange is that the original problem which made me get into this whole issue, was that is was endlessly booting to the "samsung" logo - but when I booted to System Recovery or Download/ODIN modes, it stopped rebooting endlessly and stayed on... it was also showing the charging indication when powered off... the battery was charging well ever since.
- Why would it bootloop when connected to the charger ? is it possible that the bootloader went bad during my attept to install firmware using ODIN ? I know it always went through the boot.img and recovery.img successfully and only got stuck at about 50% when installing system.img...
I think the current bootloop problem began only once the battery ran out of power. But why wouldn't it charge at all now ??? It's supposed to still charge in this state, isn't it ?
wurlitzer99 said:
Hi, thanks for the help !
The error is this:
http://statics1.grupoandroid.com/up...1850.jpg.d2bb2a8b77e4fba5fc6467f3d1547886.jpg
I *think* I have some direction... here's what I did/found:
- I installed Smart Switch on my Mac, and chose "Reinstall Device Driver" from the menu. Then restarted the MAC
- I loaded Smart Switch, and Chose "Emergency Software Recovery and Initialization". Then chose the "Device Initialization" tab
- Added the model number "SM-A800F" and the device's serial number (which are physically written on my device).
Smart Switch determined the firmware version to be used for initialization, as:
PDA:QC3 / PHONEG3 / CSCH4(XXV)
- Smart Switch asked to:
1. Power the device down
2. Load recovery mode by pushing Power+Vol Down+Home, then connect the device to the MAC and choose "Continue" to start the initialization...
The problem/s:
My device won't turn on at all, if I do not connect it to either the charger or the MAC (which acts as a supply source?) - which makes me think the battery is fully drained ? i.e when not connected at all, it won't power on.
But when connected to either the charger or MAC, it would bootloop endlessly. i.e it will load the "error" page mentioned above, shut down itself, reload again, shut down and so on.
(I have to mention, that when I first noticed the bootloop, I reset everything to factory settings, cleared cache etc, and it still bootlooped on the Samsung logo).
If when it shuts down during the loop, I push Power+Vol Down+Home, it would boot to ODIN recovery page, where I can push UP for the Download page, but it will still reboot and will again load into the "error" page, which will again reboot endlessly. If I take the charger off the device, it powers off and won't load with any combination of button push.
I also cannot just make it shut down when the charger is connected, using any of the possible button combinations...
I wonder:
- Is there there's a problem which prevents the battery from being charged at all ?
What's strange is that the original problem which made me get into this whole issue, was that is was endlessly booting to the "samsung" logo - but when I booted to System Recovery or Download/ODIN modes, it stopped rebooting endlessly and stayed on... it was also showing the charging indication when powered off... the battery was charging well ever since.
- Why would it bootloop when connected to the charger ? is it possible that the bootloader went bad during my attept to install firmware using ODIN ? I know it always went through the boot.img and recovery.img successfully and only got stuck at about 50% when installing system.img...
I think the current bootloop problem began only once the battery ran out of power. But why wouldn't it charge at all now ??? It's supposed to still charge in this state, isn't it ?
Click to expand...
Click to collapse
Hmmm, the thing is, the battery charging process is actually held on some kind of "mini-boot" OS on Samsung I believe, where the phone boots into a certain state, with that said mini-os to display the battery charging info and this kind of things.
My guess is that you *might* have, or more likely your phone did corrupt the flash at some point for x or y reason.
What I'd do is :
Let the phone on a charger a whole night doing its bootlooping thing. And see from there if the battery would charge.
I'd try another computer with Odin just to be sure something is not triggering the reboot process at some point.
And if all the above fails, you still have the warranty, so beside time, you would not be losing any money..
I'm going to write a long post. But I believe it will help a lot of people having a similar problem.
Long story short - problem solved! but it took much of my nerves (and time).
I'll start with the "warranty". The so-called Samsung "warranty" which basically worths nothing!
Calling Samsung international service center, they "informed" me that I must contact Samsung Vietnam, where I bought the device, although I am not there anymore... Needless to say the local dealer in my country refused to take care of this situation, saying Samsung's warranty is regional based, rather than international... which means, only Samsung in the original country where the device was sold in, are responsible for the warranty (and therefore repair!). I had a chat with a Samsung Vietnam representative, who just kept saying "I'm sorry", and refused to let me sent the device out to them for repair! asking me to "bring it to them", although I noted him a few times that I bought it as a tourist and I am not in Vietnam anymore.... Thank you Samsung !! From now on every traveler in the world will know they basically have NO WARRANTY if they buy any Samsung device in a "foreign" country while traveling abroad!
Now for the solution:
I started by letting the device staying connected to the charger overnight, which didn't help. With the OS now installed, I realize that the battery was NOT CHARGED ! it was completely drained, although connected to a charger for long hours... So, know from now on that if your boot data is corrupted, it may cause the device NOT TO CHARGE THE BATTERY at all. Luckily, my desktop PC could use the device while connected to it although the battery was empty, until the problem was sorted out. I did get a crash on my MAC tough (Log said it was USB related), while using Smart Switch, so one option is that it could not supply enough power to the device to keep it keep working at all, or working correctly... So my suggestion is to use a desktop Windows PC in this case, which can potentially provide more power to a device with 0% battery power.
After scratching my head, and considering removing the front panel for replacing the battery (a very risky procedure) I decided to keep on investigating....
I followed a youtube video who suggests that you should install Smart Switch on a PC, choose "reinstall driver" from the menu, restart the PC, then use Emergency Recovery and Initialization, enter the phone model number in the search box (as appearing on the back of the device) , and once it recognizes the model, also to enter its serial number. Here's the video:
https://www.youtube.com/watch?v=1yXQUFrEWg4
This basically brings up a popup message saying Smart Switch detects a compatible firmware for this device, and is about to download and install it. It then asks the user to do the Power+Vol Up+Home push combination trick + pushing UP once the page is loaded in order to "Continue" and bring up the ODIN Download screen, which worked for me if did that as soon as the device shuts down (in the middle of the bootloop). As I couldn't make it load at all with no charger connected, I had it connected to the charger, and once I saw the Smart Switch message asking to do the push combination, I quickly connected it to the computer using another cable which was already connected to the PC USB port on its other end.
Somehow, I could at last make Smart Switch finally start downloading the firmware from the web, and the device again disconnected (bootlooped), but luckily Smart Switch didn't care about it disconnecting, and kept on downloading the firmware. At about 85% of the progress bar state, I could find the downloaded firmware on the temp folders, which are described in this thread:
http://forum.gsmhosting.com/vbb/f777/samsung-firmware-download-belongs-his-serial-number-2038404/
I had to make sure it wasn't still downloading, and watched the "last modified" state of the file to make sure they are not being downloaded anymore. CAUTION: although the AP was not downloading anymore, I know it was probably not good as ODIN couldn't verify it when I tested it. USE ONLY SMART SWITCH !
I quickly copied the folder to which the app extracted the BL and AP files it downloaded, and finally had an officialy bootloader (BL) image, which I could use in ODIN in order to reupload a correct, "official" bootloader to the device....
I hoped the device won't bootloop in the middle, but luckily ODIN was fast enough to send the image successfully, with a "PASSED" status, and the device booted with a nice "Samsung" logo directly to a System Recovery page!
What I exactly did, was loading ODIN, then loading ONLY the BL file into the BL field in ODIN, having it verifying it, and once verified I connected the device, and as soon as ODIN recognized it, pushed START. It managed to upload the image into the device in a few seconds! It seems then, that the bootloop was not caused by a bad battery, but as a result of a corrupt upload of an AP image through ODIN - or because I possibly was using an incorrect version when I tried to upload an AP files to the device on my first attempt to flash it.
Note that I did search for the correct, compatible AP file, by country and model (on Sammobile) but it didn't' work (stuck at 50% in ODIN) ! so I really suggest everyone TO ONLY USE SMART SWITCH if they want to be sure that the correct firmware is being used, and avoid similar situations...
I then deleted the temp files from the PC (the actual ones which were in the temp folder), reinstalled the drivers from inside Smart Switch (just in case), booted the device to Download mode (WHICH DIDN'T BOOTLOOP this time), let Windows installing the drivers (checked in Device Manager), then restarted the PC, and ran Smart Switch again. I repeated the procedure of loading Emergency and Initialization, entering the model and serial number, having it fully downloading the firmware (again) from the web, and installing the firmware into the device. This time it completed the process, and I finally had the device installing and booting into a fresh version 6.0.1 of Android!
Hope it helps!
Hi Guys,
Today I think I bricked my phone and I would appreciate any help.
I will describe the whole situation.
So around 2019 May, I rooted my device and decided to flash a stock based,debloated custom rom. Everything work just fined including downloading mode and recovery menu. Today, I decided to try out [S7/S7 Edge][OneUI Pie][JetBlackUI] LightROM, however strangely I was not able to boot either to TWRP neither to downloading mode via key combination.
However I had install TWRP app and from there i was able to boot to recovery mode,install the new rom and try it out.
For some reason root was not enabled in the new rom, so i figured I will try to do it via TWRP however I was unable to boot, since root access is needed to boot from TWRP app + key combo still did not work.
After searching on google, I found a poprgram which can do the trick. (Recovey-Download (CMD)
With this I was able to boot to recovery mode. Now I thought, since all this mess up was started with the new roms, I decided to restore my original stock rom, which I had a back up of. It booted up first and seemed okay, but I was curious if this solved the issues with the key comb, so I tried it going downloading mode, but it only worked with the program ((Recovey-Download (CMD)), and I saw that it is probably not gonna be good, since it only had the blue screen, but no data in the upper left corner.
Then I restarted the device and now it say " Custom binary blocked by FRP lock". and turns off itself.
I saw that FRP lock could be solved easly with Odin fresh install, problem is I have no idea how to go downloading mode. ( Assuming at this point I still can).
Sorry for the long essay but i think the more detail the easier to diagnose. Also, thank you for reading.
I would greatly appreciate any help.
BR
Csaba
Managed to solve it with USB JIG.
Is your phone an Exynos/Snapdragon variant?
csesztes said:
Managed to solve it with USB JIG.
Click to expand...
Click to collapse
Hey, how did you manage to get your phone into dl mode with an USB jig? I want to try this out, but you're the only one here who's confirmed that you were able to do this on an S7 Edge.
Good evening! I hope you can help me.
I flashed LineageOS 14.1, but I wanted to go back to EMUI. I made all the wipes and tried to flash different stock firmwares through a forced update (volume buttons + power button), but it never worked. At that point, I read about a guy in this forum who suggested to create a flashable zip with Huawei Update Extractor: I followed the suggestion and tried to flash it with TWRP. No error was given, but when I tried to restart, TWRP told me I had no OS installed. I thought it was strange, so I tried to restart anyway. That's when I got in rescue mode. I can't get into the recovery and I can't use fastboot. What rescue mode shows me is:
RESCUE MODE
Attention!
Please update system again
Update User Guide:
*link*
*android avatar*
Error!
Func NO: 10 (boot image)
Error NO: 2 (load failed!)
Pressing the three buttons, I'm able to force an update. The problem is I can't find a firmware that doesn't get rejected. With Lollipop firmwares, it starts to install, but it fails at 12%. With Marshmallow ones, the installation process doesn't even start.
What can I do to make it work again? I'm very sad because this phone was gifted to me a couple of days ago and I already messed it up. I don't even know how to turn it off.
What can I do to get in fastboot mode? At that point, what should I do to flash the stock firmware? Or maybe do I need to find the first stock firmware ever installed into this phone to make the forced update work?
Please, I need help. Thank you in advance!
P.S. The phone's model is ALE-L21. I live in Italy, so I assume it's a European version.
Did you managed to fix this?
Jhon_Locke said:
Did you managed to fix this?
Click to expand...
Click to collapse
Not yet, but I'm working on it. I found out that the device is recognized by my PC if I follow these steps:
1. Connect the phone to the PC and wait for it to go in rescue mode;
2. Wait until the notification LED stops to blink;
3. Disconnect the USB cable;
4. Press volume - and power button;
5. Reconnect the cable.
At that point, the screen turns black and the phone is recognized as "㌲㔴㜶㤸". I installed the drivers and now it's recognized as "HUAWEI USB COM 1.0". I should be able to reflash the partitions and make my phone work again, but I'm still trying to understand how to do it correctly.
Any help is appreciated!
ErikChimello said:
Not yet, but I'm working on it. I found out that the device is recognized by my PC if I follow these steps:
1. Connect the phone to the PC and wait for it to go in rescue mode;
2. Wait until the notification LED stops to blink;
3. Disconnect the USB cable;
4. Press volume - and power button;
5. Reconnect the cable.
At that point, the screen turns black and the phone is recognized as "㌲㔴㜶㤸". I installed the drivers and now it's recognized as "HUAWEI USB COM 1.0". I should be able to reflash the partitions and make my phone work again, but I'm still trying to understand how to do it correctly.
Any help is appreciated!
Click to expand...
Click to collapse
fastboot detects your device when you plug it into your computer?
I mean, if you run "fastboot devices" it shows your phone?
I've had this same problem but with an P8 Lite 2017, after flashing some ROM that supposedly was the stock one and trying to flash recovery I ended up with my phone bootlooping into rescue mode, I was able to "bypass" this thing rebooting my phone like crazy, seriously like after 20 reboot it finally booted into the damn ROM and I never touched the phone again. Sometimes when the phone ran out of battery and tried to power it on the phone booted into rescue mode and again after some reboots it booted to Android but now I want to install a custom ROM or at the very least root this damn phone so that's why I'm asking you if you have solved this, if you do then probably if I follow the same steps I would be able to fix that screen, hopefully.
If you are able to flash something start with flashing all recoveries your update.app has, maybe that's the problem (at least in my phone it is).
Jhon_Locke said:
fastboot detects your device when you plug it into your computer?
I mean, if you run "fastboot devices" it shows your phone?
I've had this same problem but with an P8 Lite 2017, after flashing some ROM that supposedly was the stock one and trying to flash recovery I ended up with my phone bootlooping into rescue mode, I was able to "bypass" this thing rebooting my phone like crazy, seriously like after 20 reboot it finally booted into the damn ROM and I never touched the phone again. Sometimes when the phone ran out of battery and tried to power it on the phone booted into rescue mode and again after some reboots it booted to Android but now I want to install a custom ROM or at the very least root this damn phone so that's why I'm asking you if you have solved this, if you do then probably if I follow the same steps I would be able to fix that screen, hopefully.
If you are able to flash something start with flashing all recoveries your update.app has, maybe that's the problem (at least in my phone it is).
Click to expand...
Click to collapse
No, it doesn't show anything if I write that command...
I guess mine won't ever boot into the rom because it seems like there's no system installed. I made some researches and found out there are some softwares that let you reflash the partitions IF the phone is recognized as "HUAWEI USB COM 1.0". I'm still trying to figure out how to do it correctly though. I feel like if I do something wrong, then my phone won't probably turn on again.
In your case, you should be able to flash a custom rom without any issue. You just have to be very careful and inform you as much as you can: I don't want your phone to end up like mine?. Anyway, it seems pretty hard to go back to the stock rom, so think about it before you flash a custom rom. Also, make a Nandroid Backup is very important.