Related
Hi, I was following this guide http://wiki.cyanogenmod.com/wiki/Samsung_Galaxy_S:_Full_Update_Guide found on http://forum.xda-developers.com/showthread.php?t=1298691.
I got as far as the Installing the ClockworkMod Recovery, when I got to step 8 'Click Start on the Heimdall Frontend. A blue transfer bar will appear on the phone showing the kernel being transferred. The device will reboot automatically.' BUT when the phone tried to reboot it gets stuck on the first Galaxy S screen. I could get in to download mode and recovery mode but nothing else. Does this mean my mobile is bricked? What do I do know?
Thanks in advance
You have flashed a rom, not only root your device. And cyanogenmod is not based on samsung firmware.
Think you shold read some more.
But, how long do you wait on the s logo? It thakes some time to boot up first time when catche is wiped.
If you only want to root you shold search for cf root for your stock rom. If you want to go back, you have to download a stock rom. Found att samfirmware.com
Sent from my GT-I9000 using Tapatalk
No not bricked (nowhere near)............ Reflash...
I have read many times that re-flashing will do the trick. If you have download mode, you can flash any rom onto it, i would use odin as it may be the safest whilst you being in limbo. Then if you want to follow a link for CM 7.1 that is both v.entertaining (my opinion) and clear i suggest you click on the link in my sig...
Robert - Sorry I did mean flash as well as root. I waited around 15-20 minutes, isnt that long enough?
Talon - I have tried to re-flash using the guide method I was originally using but get the same problem. To be honest from looking at Odin information on this forum, it has confused me quite a bit (lot of different advice), not sure if I am doing the right thing.
I did make the mistake of jumping into trying to flash & root my phone. Any help of what to do to get my phone to a working state, would be very much appreciated.
@OP: as long as you can put phone in Download mode - it is not bricked.
ALWAYS, you can restore everything by flashing stock ROM with repartition.
If you will not be able to go to download mode - well... then you have something to worry about
spamtrash said:
@OP: as long as you can put phone in Download mode - it is not bricked.
ALWAYS, you can restore everything by flashing stock ROM with repartition.
If you will not be able to go to download mode - well... then you have something to worry about
Click to expand...
Click to collapse
I'm a bit confused, what would be the best way to do that?
Well find stock FW from below, then flash it using the guides..
Generally now days you get 2 files, Pit either 512 513 or 813 (or something similar). And you get a .tar file or other zip type extension and put that in pda. Then flash
you may get 3 files and a pit file in which case you put it in the appropriate places....
Ive written this guide and telling you it is a GUIDE. Wherever you get your files from there should be instructions as to what to do.
For example you may need to do a factory reset before (unlikely but still) More likely is that you will have to disable lagfix, but you shoudnt have to worry about that. Main thing read the guide and follow the guide from where you get the files. The thread you get it from...read the first and last 5 pages, more if you want to be safe.
Now files, i have links to stock FW below, guide are usually present within them. If not read the thread, but also read the thread and search th thread for answers or the section or the SGS forum.
IF before you were on 2.2.x - try some Froyo from sammfirmware. If you were on Ginger - try Click
Of course, you can search for EAzyBase... but it is more advanced, start from the basics...
OMG, there are tons of tutorials and how to's in here about flashing and rooting phones... who uses heimdall? get Odin for flashing:
1. Install KIES for drivers (you might already have done this).
2. Get a rom from samfirmware/sammobile, I recommend JVP because it has gingerbread bootloaders: http://www.sammobile.com/threads/17-Samsung-I9000-Galaxy-S-Firmwares
3. Get Odin (sorry I coudn't find a link)
4. Get your phone in download mode (VolDown, Home, Power).
5. Connect your phone to PC with USB cable.
6. Set the PDA, CSC and MODEM files in Odin from the firmware you downloaded from step2.
7. Make sure you have "re-partition" enabled and set the .PIT file to use the *512.pit also included in the firmware from step 2.
8. click start.
9. Start your phone and set up the startup wizard.
9. For rooting, get the CF-root for your firmware from here: http://forum.xda-developers.com/showthread.php?t=788108
10. Get your phone into download again.
11. DON'T check repartition in odin, only select the CF-Root file as PDA (you have to use the CF-Root-***.TAR, important to use .TAR and not .ZIP.
12. Flash again, now you are rooted!!
Hey there
Today I got a message that I could update my Yoga 2 Tablet via the System Updater, but it doesn't quite work.
First of all about the device:
Lenovo Yoga 2 Tablet 1050F
Running current version: YT-1050F_USR_S0000198_1504220313_WW21_ROW
New version I wanna update to: YT2-1050F_USR_S1000031_1506111400_WW52_ROW
The problem:
I can download the update and when I press the install button, the tablet reboots into recovery mode. The update process begins and reaches 100% pretty quickly. After some time, it says the update failed though.
What I tried so far:
Downloading and updating again, it didn't work.
Download and starting the update on my PC with Lenovo Smart Assistant, didn't work.
Change the country code with the easyimage.zip file and the ####6020# code. I changed it to de (which is my usual country code) and us, but both did not help with the software update.
So... I really do not have any knowledge about android and can't seem to find another clue what to do next. Maybe someone of you can help me with this issue.
bjorr said:
Hey there
Today I got a message that I could update my Yoga 2 Tablet via the System Updater, but it doesn't quite work.
First of all about the device:
Lenovo Yoga 2 Tablet 1050F
Running current version: YT-1050F_USR_S0000198_1504220313_WW21_ROW
New version I wanna update to: YT2-1050F_USR_S1000031_1506111400_WW52_ROW
The problem:
I can download the update and when I press the install button, the tablet reboots into recovery mode. The update process begins and reaches 100% pretty quickly. After some time, it says the update failed though.
What I tried so far:
Downloading and updating again, it didn't work.
Download and starting the update on my PC with Lenovo Smart Assistant, didn't work.
Change the country code with the easyimage.zip file and the ####6020# code. I changed it to de (which is my usual country code) and us, but both did not help with the software update.
So... I really do not have any knowledge about android and can't seem to find another clue what to do next. Maybe someone of you can help me with this issue.
Click to expand...
Click to collapse
I posted the same issue already within the root thread. My device is rooted and after the download it started to upgrade and after reaching 100% it says it failed. I even did a factory reset - but SuperSu stays present and no upgrade is possible. I do not want to flash it via flashify - as bricking might be possible with that methode.
Maybe anyone has an idea how to proceed!?
Thanks for the reply.
I forgot to mention, my tablet isn't rooted and I tried a factory reset aswell, but nothing worked.
/E: So if anyone has the same problem: The solution is to flash the tablet to stack rom with PhoneFlashTool and update it afterwards. No problems since.
I flashed to stock rom downloaded from Russian Site with Phoneflashtool and tried to update. Update went to 100% then "failed". Any ideas anyone?
bowyerv said:
I flashed to stock rom downloaded from Russian Site with Phoneflashtool and tried to update. Update went to 100% then "failed". Any ideas anyone?
Click to expand...
Click to collapse
You missed presumably one important step after flashing the original rom, changing the country code prior OTA - which was posted already in another thread:
If system update fails do the following:
1. Flash stock firmware
2. Optionally you can wipe user data (I never did that) from DROIDBOOT
3. Go to contacts manager. Create some dummy contact if list is empty.
4. Go to Search / Find Contacts and enter ####6020#. It will ask you to select country code (first two latin letters, ignore Chinese).
5. Select what you want, then reboot.
6. Go to System Update
7. Install OTA update
Thanks. Will give that a go.
/E After the above it now tells me that I already have the latest version at YT2-1050F_USR-S000198_1504220313_WW21_ROW and that there is no update. Surely they have not taken the update offline??!
/EE I used the Update.zip I had previously downloaded (when the update first failed).
Placed this on the SD card and installed it via the update tools.
Thank you for those who helped me
Is there any chance You can upload this update.zip file? Thanks
Link to Lollipop Update.zip for YT2-1050F
worek555 said:
Is there any chance You can upload this update.zip file? Thanks
Click to expand...
Click to collapse
The storage I use wont let me link to my uploaded file! I have provided you the link by PM
Exactly the same problem. The ####6020# not work. Before m'y tablette was rooted but now after flash with easyimage, the stock ROM is OK but no update. I'm verry disapointed. Can you help me?
Thanks
1050F. Update fails.
Hi people, new guy here. I got redirected by some friendly dude.
Anyway, I apparantly have the same problem. Device has never been rooted. Tried the update as is, tried after a factory reset, tried #### contact hocus pocus, did not try anything involving a PC since I don't have one with that still has Windows and I can't seem to figure out Wine dependencies on my Debian box.
So, yeah, I guess I'll call the 1 euro a minute Lenovo support desk now. :laugh:
Anyway, thanks for having me, I'm subscribed to the thread . If I find out something before you guys do I'll let you know, but by all means don't stay up for it.
AgentAmsterdam said:
Hi people, new guy here. I got redirected by some friendly dude.
Anyway, I apparantly have the same problem. Device has never been rooted. Tried the update as is, tried after a factory reset, tried #### contact hocus pocus, did not try anything involving a PC since I don't have one with that still has Windows and I can't seem to figure out Wine dependencies on my Debian box.
So, yeah, I guess I'll call the 1 euro a minute Lenovo support desk now. :laugh:
Anyway, thanks for having me, I'm subscribed to the thread . If I find out something before you guys do I'll let you know, but by all means don't stay up for it.
Click to expand...
Click to collapse
I run Arch on all my machines. I was able to use my virtualbox windoze 8.1 (It came on my laptop but never booted it... ) vm to use the intelphonetool. I flashed this stock rom here and then took the ota lollipop update. If you want to root this works in Linux.
BTW... temporary Windows vm's can be found here
Guichinga said:
I posted the same issue already within the root thread. My device is rooted and after the download it started to upgrade and after reaching 100% it says it failed. I even did a factory reset - but SuperSu stays present and no upgrade is possible. I do not want to flash it via flashify - as bricking might be possible with that methode.
Maybe anyone has an idea how to proceed!?
Click to expand...
Click to collapse
Guichinga said:
You missed presumably one important step after flashing the original rom, changing the country code prior OTA - which was posted already in another thread:
If system update fails do the following:
1. Flash stock firmware
2. Optionally you can wipe user data (I never did that) from DROIDBOOT
3. Go to contacts manager. Create some dummy contact if list is empty.
4. Go to Search / Find Contacts and enter ####6020#. It will ask you to select country code (first two latin letters, ignore Chinese).
5. Select what you want, then reboot.
6. Go to System Update
7. Install OTA update
Click to expand...
Click to collapse
workdowg said:
I run Arch on all my machines. I was able to use my virtualbox windoze 8.1 (It came on my laptop but never booted it... ) vm to use the intelphonetool. I flashed this stock rom here and then took the ota lollipop update. If you want to root this works in Linux.
BTW... temporary Windows vm's can be found here
Click to expand...
Click to collapse
i have same problem and i don`t know what can i do
semsem81 said:
i have same problem and i don`t know what can i do
Click to expand...
Click to collapse
I don't know which problem you have...
Rooted and go back to stock to take OTA?
Return to stock KK firmware - Yoga Tablet 2 1050F
1) Download - This - AFH - kitkat-YT2-1050F_S0198_150422_ROW.7z
2) Extract the zipfile to a directory on PC somewhere
3) Goto "tools" folder and install the exe's in this order
__a)PhoneFlashTool_4.4.4.1_external_win32.exe
__b)iSocUSB-Driver-Setup-1.2.0.exe
__c)IntelAndroidDrvSetup1.5.0.exe
4) Start PhoneFlashTool and select settings (Upper left corner)
5) Tick "force sparcing" and change size to 500mb
6) Power off tablet and connect with usb
7) From off, hold volume up and power until tablet vibrates and release power (still holding volume up)
8) Tablet should now be in "Droidboot" and PhoneFlashTool should list it on the top
9) In PhoneFlashTool click browse and select flash.xml from the "target_bin" folder
10) WAIT!!! until you see "Result okay" on tablet AND "Flash Sucess" in PhoneFlashTool
11) Reboot
12) When Android starts skip all dialogs (tablet is going to factory reset anyway)
13) Select Contacts from desktop and make 1 dummy contact
14) In the search bar type "####6020#" and then select your country
15) Tablet reboots and you are on stock KitKat again and should receive an update notice for Lollipop
Click to expand...
Click to collapse
Stuck on bios after FAILED Lollipop to Kitkat downgrade?
Repair Lollipop to KitKat bios error
1) Get the firmware kitkat-YT2-1050F_S0198_150422_ROW.7z - https://www.androidfilehost.com/?fid=24052804347778640
2) Extract the firmware on PC
3) Download LtoKKxml.7z - https://www.androidfilehost.com/?fid=24052804347783496
4) Extract or copy the content of this zip to where you extracted the firmware, so that the flash_*.xml are located next to all the image files of the firmware
5) Edit the file flash-LtoKK_PVT_810.xml and remove the the "command" tags which contain "format data" and "erase data" (the XML tag from <command> to </command>)
6) Reboot your tablet into fastboot mode (hold power up, down and power buttons)and use PhoneFlashTool to flash this flash-LtoKK_PVT_810.xml
7) Wait for it to finish and when the tablet restarts make sure it goes back to fastboot. If not then power off and restart into fastboot
8) Flash the flash.xml which is located in the folder. This will flash all the KitKat firmware components. That's it.
Be careful if you do something wrong then a brick is very likely. Hope this helps
Originally posted by [email protected]
These are links to other variant firmwares (not my hosting):
830F: YT2-830F_S0195_150422_ROW.7z - https://cloud.mail.ru/public/Z2US9gd6f2ei/YT2-830F_S0195_150422_ROW.7z
830L: YT2-830L_S0209_150422_ROW.7z - https://cloud.mail.ru/public/2hrDmzneLDLY/YT2-830L_S0209_150422_ROW.7z
1050L YT2-1050L_S0225_150422_ROW.7z - https://cloud.mail.ru/public/2GFji3ub9JdG/YT2-1050L_S0225_150422_ROW.7z
1380L YT2 -1380L_S0216_150428_ROW.7z - https://cloud.mail.ru/public/CGZs/Nt8NE1pit
1380F YT2-1380F_S0219_150428_ROW.7z - https://cloud.mail.ru/public/8s5Q/dfuSXn7oi
Click to expand...
Click to collapse
Root Lollipop or Kitkat?
Root Lollipop or Kitkat on 1050F - 8/4/2015
Windows PC:
Thread by [email protected] - http://forum.xda-developers.com/showpost.php?p=57543871&postcount=1
Lollipop - Trigger 4
Kitkat - Trigger 3
Linux PC:
Thread by [email protected] - http://forum.xda-developers.com/showpost.php?p=61067755&postcount=1
Lollipop - Trigger 4
Kitkat - Trigger 3
Click to expand...
Click to collapse
workdowg
I don't know which problem you have...
My device is rooted and after the download it started to upgrade and after reaching 100% it says it failed. I even did a factory reset
i don't know how to flash firmware and i wanna to update to 5.0
my device is yoga tablet 2-1050L
Deleted. Will update
---------- Post added at 02:34 PM ---------- Previous post was at 02:30 PM ----------
semsem81 said:
workdowg
I don't know which problem you have...
My device is rooted and after the download it started to upgrade and after reaching 100% it says it failed. I even did a factory reset
i don't know how to flash firmware and i wanna to update to 5.0
my device is yoga tablet 2-1050L
Click to expand...
Click to collapse
I'll post files for you. You were able to root your device, so I'm sure you can handle flashing back to stock. I need to sleep right now before work.
Sent from my YOGA Tablet 2-1050F
workdowg said:
Deleted. Will update
---------- Post added at 02:34 PM ---------- Previous post was at 02:30 PM ----------
I'll post files for you. You were able to root your device, so I'm sure you can handle flashing back to stock. I need to sleep right now before work.
Sent from my YOGA Tablet 2-1050F
Click to expand...
Click to collapse
thx for ur replay but i don't have experience to flashing stock and i rooted my device with luck
so its okay you can go to sleep and sorry to bother you
Some info, probably well known, but have a question about it.
Hi,
I found a folder 'lenovoota' om my tablet. It contains a file called YT2-1050F_USR_S000198_1504220313_WW21_ROW_TO_YT2-1050F_USR_S100067_1507101258_WW52_ROW.zip
and one called packages.xml.
Both can't be opened / are corrupt. 0 bytes each.
So, correct me if I'm wrong, the update fails at download already, right? Would it be of any use to get these two files somewhere and replace the corrupted ones, then trigger the updating process again? Or is that a bit optimistic?
Thanks.
I'm a bit reluctant about the instructions above btw. I know what's what, but, you know, *very* old machine running debian, not sure how VM would perform. Apart from that I am certainly going to be overly focussed on getting the details right and brick my tablet by forgetting a whole major step or something. THanks anyway, though, appreciate the effort.
---------- Post added at 09:24 AM ---------- Previous post was at 09:17 AM ----------
AgentAmsterdam said:
Hi,
I found a folder 'lenovoota' om my tablet. It contains a file called YT2-1050F_USR_S000198_1504220313_WW21_ROW_TO_YT2-1050F_USR_S100067_1507101258_WW52_ROW.zip
and one called packages.xml.
Both can't be opened / are corrupt. 0 bytes each.
So, correct me if I'm wrong, the update fails at download already, right? Would it be of any use to get these two files somewhere and replace the corrupted ones, then trigger the updating process again? Or is that a bit optimistic?
Thanks.
I'm a bit reluctant about the instructions above btw. I know what's what, but, you know, *very* old machine running debian, not sure how VM would perform. Apart from that I am certainly going to be overly focussed on getting the details right and brick my tablet by forgetting a whole major step or something. THanks anyway, though, appreciate the effort.
Click to expand...
Click to collapse
EDIT: ah wait I think I get it, the row / version thing. I'll check my current version and see what the linux thread has to offer...
AgentAmsterdam said:
Hi,
I found a folder 'lenovoota' om my tablet. It contains a file called YT2-1050F_USR_S000198_1504220313_WW21_ROW_TO_YT2-1050F_USR_S100067_1507101258_WW52_ROW.zip
and one called packages.xml.
Both can't be opened / are corrupt. 0 bytes each.
So, correct me if I'm wrong, the update fails at download already, right? Would it be of any use to get these two files somewhere and replace the corrupted ones, then trigger the updating process again? Or is that a bit optimistic?
Thanks.
I'm a bit reluctant about the instructions above btw. I know what's what, but, you know, *very* old machine running debian, not sure how VM would perform. Apart from that I am certainly going to be overly focussed on getting the details right and brick my tablet by forgetting a whole major step or something. THanks anyway, though, appreciate the effort.
---------- Post added at 09:24 AM ---------- Previous post was at 09:17 AM ----------
EDIT: ah wait I think I get it, the row / version thing. I'll check my current version and see what the linux thread has to offer...
Click to expand...
Click to collapse
Yes, it shows as 0 bytes when it fails.
I captured the OTA file from the 1050F. It is usable only on a non-rooted stock device and those devices should take the OTA successfully anyway... But it had the files I needed to repair the bios error from trying to downgrade from Lollipop to KitKat.
And I feel your pain with using a VM. My laptop is pretty new and I have my OEM copy of Windows on an external SSD so it works good enough.
I tried to port the Linux version of the Intel Phone Tool to Arch and it fails because of Ubuntu specific depens. You could certainly try it. If you get it installed and it see's your tablet you should be good. Let me know if it works.
See this thread: http://forum.xda-developers.com/thinkpad-tablet/general/how-to-one-guide-yoga-tablet-2-t3174597
workdowg said:
Yes, it shows as 0 bytes when it fails.
I captured the OTA file from the 1050F. It is usable only on a non-rooted stock device and those devices should take the OTA successfully anyway...
Click to expand...
Click to collapse
Well, mine is unrooted and it still fails... Ill check out that thread.
Hi there
So, im here because i got problem with my Yoga 2 10" 1050L
Well, i was trying to update my Yoga to 5.0.1 but my tablet says that there is no update.
I was tryin to use Lenovo Smart Assistant - same, no update.
Then i do hard reset (power button + vol+), fresh install, and... kitkat do not recognize any new updates to lollipop.
Then i contact with Lenovo Poland, they was tryin to turn on update from servers for my device - nothing happens.
I got 2 devices, both from Poland, second one (i got two same Yogas, both 1050L) is running 5.0.1 without any problems (it update itself instantly after 1st boot).
So, what can i do now?! Is it any possibilities to get update *.zip file from anywhere, to do it manualy from settings menu in tablet?
Sorry for my bad english, its still not my main )
NOTE-1:
I'm not a developer or something even near to that. All information provided here is copied from different internet sources like this & this & this and many others.
It's according to best of my knowledge and I'll not be responsible for any harm to you or your device. It works perfectly for me. You may try it on your own risk.
Save / backup your data before continuing. Whole device will be wiped.
NOTE-2:
If you have a custom recovery, install Stock ROM (v2.1.0.13 or v2.1.0.12) instead.
If you don't have a custom recovery, you may get one here or here.
If your device is bricked and can't boot into recovery or bootloader mode (read here what it is), proceed.
NOTE-3:
Given firmware link is v2.1.0.13 for device 059V782. There are some variants of Nokia X2DS (other product codes) which were officially updated from 2.1.0.11 to 2.1.0.12, so they dont support version 2.1.0.13.
Make sure your device supports 2.1.0.13 by googling your product code (written on back of device, see by removing back cover) or you may get in trouble. In case if you need 2.1.0.12, download it from some other link and follow the instructions given here.
NOTE-4:
Hard-bricked devices (with no buttons working, no Download Mode) may also be recovered by this method but with a slightly different procedure.
QFIL can also be used instead of NCS, but NCS feels a kinda little bit official way
REQUIREMENTS:
A PC with Windows and uninterrupted power supply. (I used Dell Inspiron 15R with Windows 8.1 and 10).
A USB data cable.
Fully charged phone, soft-bricked at maximum i.e. no recovery, no boot accessible
STEPS:
Download and Install NCS to your PC.
Copy UserGroupsConfiguration.cfg to "C:\Program Files (x86)\Nokia\Nokia Care Suite\Product Support Tool For Store 5".
Download Firmware and extract to "C:\ProgramData\Nokia\Packages\Products\RM-1013".
Launch NCS > Product Support Tool for Store 5.
At Sign-In screen, click Work Offline.
Disable Automatic Product Selection.
Go to File > Open Product and select RM-1013.
Click Programming > Recovery. Downloaded Firmware must be listed there.
Click Start and follow instructions. DO NOT INTERRUPT FLASHING PROCESS OR IT MAY HARD BRICK YOUR PHONE LEAVING IT USELESS.
Wait a few minutes and done. You have a newly purchased phone in your hands if all goes well.
Thanks for making a proper post for this.:good:
Devnikolus said:
Thanks for making a proper post for this.:good:
Click to expand...
Click to collapse
There are many others but mine is simple and solid
mirfatif said:
NOTE:
I'm not a developer or something even near to that. All information provided here is copied from different internet sources and according to best of my knowledge.
I'll not be responsible for any harm to you or your device. It works perfectly for me. You may try it on your own risk.
Save / backup your data before continuing. Whole device will be wiped.
REQUIREMENTS:
A PC with Windows and uninterrupted power supply. (I used Dell Inspiron 15R with Windows 8.1 and 10).
A USB data cable.
Fully charged phone, soft-bricked at maximum i.e. no recovery, no boot accessible
STEPS:
Download and Install NCS to your PC.
Copy UserGroupsConfiguration.cfg to "C:\Program Files (x86)\Nokia\Nokia Care Suite\Product Support Tool For Store 5".
Download Firmware and extract to "C:\ProgramData\Nokia\Packages\Products\RM-1013".
Launch NCS > Product Support Tool for Store 5.
At Sign-In screen, click Work Offline.
Disable Automatic Product Selection.
Go to File > Open Product and select RM-1013.
Click Programming > Recovery. Downloaded Firmware must be listed there.
Click Start and follow instructions. DO NOT INTERRUPT FLASHING PROCESS OR IT MAY HARD BRICK YOUR PHONE LEAVING IT USELESS.
Wait a few minutes and done. You have a newly purchased phone in your hands if all goes well.
Click to expand...
Click to collapse
Bro, i got an error with
Initializing WinUSB with device handle. The parameter is incorrect
Exception:
System.ComponentModel.Win32Exception (0x80004005): Initializing WinUSB with device handle. The parameter is incorrect
at Nokia.Merak.UsbDeviceIo.WinUsbIo.CheckError(Boolean expression, String message)
at Nokia.Merak.UsbDeviceIo.WinUsbIpen()
at Nokia.Merak.UsbDeviceIo.UsbDeviceIo..ctor(String devicePath)
at Nokia.Delta.Messaging..ctor(ConnectionDetails details)
at Nokia.CareSuite.PlugIns.DeltaRecovery.RecoveryDialog.RecoveryDialogModel.ChangeDeviceMode()
at Nokia.CareSuite.PlugIns.DeltaRecovery.RecoveryDialog.RecoveryDialogModel.Flash()
at Nokia.CareSuite.PlugIns.DeltaRecovery.RecoveryDialog.RecoveryDialogModel.<HandleDownloadVariantPackageCompleted>b__15(Object state)
please help phone not booting
himanagendra said:
Bro, i got an error with
Initializing WinUSB with device handle. The parameter is incorrect
Exception:
System.ComponentModel.Win32Exception (0x80004005): Initializing WinUSB with device handle. The parameter is incorrect
at Nokia.Merak.UsbDeviceIo.WinUsbIo.CheckError(Boolean expression, String message)
at Nokia.Merak.UsbDeviceIo.WinUsbIpen()
at Nokia.Merak.UsbDeviceIo.UsbDeviceIo..ctor(String devicePath)
at Nokia.Delta.Messaging..ctor(ConnectionDetails details)
at Nokia.CareSuite.PlugIns.DeltaRecovery.RecoveryDialog.RecoveryDialogModel.ChangeDeviceMode()
at Nokia.CareSuite.PlugIns.DeltaRecovery.RecoveryDialog.RecoveryDialogModel.Flash()
at Nokia.CareSuite.PlugIns.DeltaRecovery.RecoveryDialog.RecoveryDialogModel.<HandleDownloadVariantPackageCompleted>b__15(Object state)
please help phone not booting
Click to expand...
Click to collapse
You followed instructions 100%? Install NCS from my given link. It contains all necessary drivers including Emergency Driver. Use some other USB port on your PC. Try reinstalling NCS or try on different PC / different OS. You may also try QFIL if NCS doesn't work.
mirfatif said:
You followed instructions 100%? Install NCS from my given link. It contains all necessary drivers including Emergency Driver. Use some other USB port on your PC. Try reinstalling NCS or try on different PC / different OS. You may also try QFIL if NCS doesn't work.
Click to expand...
Click to collapse
thank god you are still there. okay here is the result.
Phone is not responding.
charging - > no indication, no screen
Volume down/up + power -> nothing. no response.
Do you know any softwares which can flash my phone without using volume up/down + power .
tnzzz for help
himanagendra said:
thank god you are still there. okay here is the result.
Phone is not responding.
charging - > no indication, no screen
Volume down/up + power -> nothing. no response.
Do you know any softwares which can flash my phone without using volume up/down + power .
tnzzz for help
Click to expand...
Click to collapse
Hmm it's hard bricked. No problem. Follow this thread. Things are explained more clearly there.
mirfatif said:
Hmm it's hard bricked. No problem. Follow this thread. Things are explained more clearly there.
Click to expand...
Click to collapse
thank you very much for your help but unfortunately it didn't work bcz as i told, nothing will comeup and even the buttons don't work.
In that case, please follow this thread
himanagendra said:
thank you very much for your help but unfortunately it didn't work bcz as i told, nothing will comeup and even the buttons don't work.
In that case, please follow this thread
Click to expand...
Click to collapse
Good. I suggested you to use QFIL already For me, both NCS and QFIL work but I didn't try any other product code firmware except 059V782 which is my device code.
What's your product code? 059V787 or 059V782? I'm gonna add a warning to my thread about this.
There are some devices which were officially updated from 2.1.0.11 to 2.1.0.12, so they don't support 2.1.0.13 as per my understanding.
mirfatif said:
Good. I suggested you to use QFIL already For me, both NCS and QFIL work but I didn't try any other product code firmware except 059V782 which is my device code.
What's your product code? 059V787 or 059V782?
Click to expand...
Click to collapse
Yeah...i thought you would give me a direct link. Anyways thanks for u help.
But bro, please mention that v2.1.0.13 don't suit for every Nokia x2 device. It doesn't suit the Indian version.
himanagendra said:
Yeah...i thought you would give me a direct link. Anyways thanks for u help.
But bro, please mention that v2.1.0.13 don't suit for every Nokia x2 device. It doesn't suit the Indian version.
Click to expand...
Click to collapse
Yes.
mirfatif said:
Good. I suggested you to use QFIL already For me, both NCS and QFIL work but I didn't try any other product code firmware except 059V782 which is my device code.
What's your product code? 059V787 or 059V782? I'm gonna add a warning to my thread about this.
There are some devices which were officially updated from 2.1.0.11 to 2.1.0.12, so they don't support 2.1.0.13 as per my understanding.
Click to expand...
Click to collapse
mirfatif said:
Yes.
Click to expand...
Click to collapse
Bro, do you know how to solve the sim 1 issue? i mean, my sim network is being recognized by the nokia x2 but, there is no signal for that.
himanagendra said:
Bro, do you know how to solve the sim 1 issue? i mean, my sim network is being recognized by the nokia x2 but, there is no signal for that.
Click to expand...
Click to collapse
Well, personally I never faced this issue. But you can try flashing @yoAeroA00 Custom Firmware. It flashes radio as well as other related partitions.
Quote:
Originally Posted by mirfatif
i cant find "C:\ProgramData\Nokia\Packages\Products\RM-1013".plz help me...
shuvo.khan97 said:
Quote:
Originally Posted by mirfatif
i cant find "C:\ProgramData\Nokia\Packages\Products\RM-1013".plz help me...
Click to expand...
Click to collapse
Create it if not found
Thx a lot, its helped me
Sent from my MI 5 using XDA-Developers Legacy app
For me please rm-1013:
2.0.0.11
059WOWO
thank you
how to connect mobile with pc in recovery mod or fast mod or normal mode i have custom rom and my sims are not working i want to stock rom again but when i select progmramming then recovery then there is no file shown in box for your information i attached img plz check and tell me the solution
lovegrw said:
how to connect mobile with pc in recovery mod or fast mod or normal mode i have custom rom and my sims are not working i want to stock rom again but when i select progmramming then recovery then there is no file shown in box for your information i attached img plz check and tell me the solution
Click to expand...
Click to collapse
Just flash stock rom zip before installing whole firmware
not able to get .xml file while flashing nokia x2
when i click on load xml in QFILL then i get new window but it shows no raw program file.
In reality it exist in extracted folder 'rm-1013 ' . When i type .xml in window it shows no file match.
please tell how to get this to proceed further.
Hi community
I have a Samsung Galaxy S7 SM-G930V with Android 7.0. I tried to get root but first I had to unlock bootloader. I flashed the "Engineer Bootloader" (a file named Samsung_G930x_QC_Rooted_BOOT.TAR) with Odin for engineering bootloader and no problem then the phone reboot. There comes the problem, the phone is on a bootloop, it shows the screen "Samsung Galaxy S7" and restart again, over and over.
People suggest to go to recovery mode and wipe data and factory reset, I already did that but it didn't work.
I'm sure that flash the complete ROM again will solve the problem but the ROM is 2.50 GB and my Internet connection is very very slow so I can't download it. Maybe flashing just the custom boot.img the problem gets solved, can somebody bring me just that file? Please I need it really much.
Thank you very much.
From the way the file name is written, it looks like the Marshmallow kernel, which is not the correct one for Nougat. Try flashing this in the AP slot in Odin. This is the correct root kernel for Nougat. The phone may bootloop a couple times after flashing this before completely booting.
Note: We are talking about engineering kernels, not bootloaders.
dude, THANK YOU VERY MUCH!!! you saved my life. I don't understand why people post tutorials with wrong files. THANK YOU VERY MUCH AGAIN.
CVertigo1 said:
From the way the file name is written, it looks like the Marshmallow kernel, which is not the correct one for Nougat. Try flashing this in the AP slot in Odin. This is the correct root kernel for Nougat. The phone may bootloop a couple times after flashing this before completely booting.
Note: We are talking about engineering kernels, not bootloaders.
Click to expand...
Click to collapse
Wow... I have searched high an low for this. Thank you.
CVertigo1 said:
From the way the file name is written, it looks like the Marshmallow kernel, which is not the correct one for Nougat. Try flashing this in the AP slot in Odin. This is the correct root kernel for Nougat. The phone may bootloop a couple times after flashing this before completely booting.
Note: We are talking about engineering kernels, not bootloaders.
Click to expand...
Click to collapse
Is there a version of this that's just stock, no root or special engineering version?
ItsKipz said:
Is there a version of this that's just stock, no root or special engineering version?
Click to expand...
Click to collapse
Hi I was just experimenting with the Verizon Recovery Utility tools on windows 10 on the computer and noticed it was temporary copying ALL BL, AP, CSC ext. Well I selected it and copied in another folder before it could erase the files when done flashing my S7 verizon back to stock. It worked! I got all the files straight from Verizon's official tool. Since windows will throw a error message to anything trying to delete files in use, when verizon tool tried to erase the temp stock files, it denied it since the file was in use by me. Aka copying to another folder as the verizon tool downloaded the files I was right there copying the files mid download and the computer let the files finish download complete and it ended up being I got the files. Im proud of myself. Lol! Being new at this.
So someone just tell me what I do to get you all a copy. They are the most current stock files from verizon. I uploaded them all into Onedrive already so files are safe just waiting for the moment someone needs them and tells me how to upload them. I see androidhostfile or something site. Can I use that one? Even though Im new at this?
Here is my screen shot of my new files.
Scottie32583 said:
Hi I was just experimenting with the Verizon Recovery Utility tools on windows 10 on the computer and noticed it was temporary copying ALL BL, AP, CSC ext. Well I selected it and copied in another folder before it could erase the files when done flashing my S7 verizon back to stock. It worked! I got all the files straight from Verizon's official tool. Since windows will throw a error message to anything trying to delete files in use, when verizon tool tried to erase the temp stock files, it denied it since the file was in use by me. Aka copying to another folder as the verizon tool downloaded the files I was right there copying the files mid download and the computer let the files finish download complete and it ended up being I got the files. Im proud of myself. Lol! Being new at this.
So someone just tell me what I do to get you all a copy. They are the most current stock files from verizon. I uploaded them all into Onedrive already so files are safe just waiting for the moment someone needs them and tells me how to upload them. I see androidhostfile or something site. Can I use that one? Even though Im new at this?
Here is my screen shot of my new files.
Click to expand...
Click to collapse
This is what the file looks like I have...
Hi, since yesterday I have a big problem with my le pro 3, while charging the phone suddenly turned off. The system did not want to turn on, so I went into recovery (TWRP) and tried to format and upload a new rom, unfortunately during the flashing, a blue screen appeared. When changing the kernel, the flashing of the rom was done, but with the installation of the gapps it hung. I tried to install another rom, but it also spilled, with this addition, that I can not enter recovery, because artifacts appear or reboots.. Only fastboot works. With it, I tried to flash the kernel, recovery, but it did not do anything. I also used (TOOL ALL in ONE) and uploaded the stock rom, but the phone still does not work. Do you know what else could help, or is buying a new phone? Thanks for help
If you can use fast boot, your phone is not hard bricked. A brick is when you can not do anything , you will have a black screen and a red blinking light if a usb cable is connected.
Try pushing Twrp ( newest version) to the phone. If that is successful boot to recovery, fully wipe your phone, reboot to recovery and install you Rom> Gapps, and Magisk. I would suggest initially flashing Lineage 15.1. Once your phone is restored, flash whatever you would like.
If it doesn't work try another cable, or another port, or another computer. Computer needs to be up to date and you may need to temporarily disable antivirus, if the All in One tool isn't working its likely that your computer is blocking the install. especially if you are using Windows 10. All the program to be open within your firewall settings. Make sure its up to date and use AIO to update android drivers and adb.
I'm not giving anything, I still can't get into recovery
miichus said:
I'm not giving anything, I still can't get into recovery
Click to expand...
Click to collapse
Click reply to the person you are talking to otherwise, they will not receive a notification of your response.
Next, if you expect some help, be courteous, to people spending their own limited free time to help with your self created issue by clicking the thank you button.
Finally read this link: https://forum.xda-developers.com/showpost.php?p=76947769&postcount=4
tsongming said:
Click reply to the person you are talking to otherwise, they will not receive a notification of your response.
Next, if you expect some help, be courteous, to people spending their own limited free time to help with your self created issue by clicking the thank you button.
Finally read this link: https://forum.xda-developers.com/showpost.php?p=76947769&postcount=4
Click to expand...
Click to collapse
The operation in flashone goes well, but it still does not help. System and recovery does not boot, only fastboot
miichus said:
The operation in flashone goes well, but it still does not help. System and recovery does not boot, only fastboot
Click to expand...
Click to collapse
What does the log say?
if you are getting no errors at at and can only boot to fastboot try the All in One tool or use the QPST method to unbrick. Also, some posted versions of Qfil are corrupted. Did you use the version that I provided a link for?
tsongming said:
What does the log say?
if you are getting no errors at at and can only boot to fastboot try the All in One tool or use the QPST method to unbrick. Also, some posted versions of Qfil are corrupted. Did you use the version that I provided a link for?
Click to expand...
Click to collapse
For the second time I tried to use flashOne and the phone started up. When entering the pin code, the phone was stuck again. When I wanted to reboot, I could only enter fastboot again.
miichus said:
For the second time I tried to use flashOne and the phone started up. When entering the pin code, the phone was stuck again. When I wanted to reboot, I could only enter fastboot again.
Click to expand...
Click to collapse
For the second time I tried to use flashOne
Click to expand...
Click to collapse
Okay sure, I provided you with a link to the correct files to use. I.E Flash 2.0 and le_zl1_qfil_ufs_fix.zip
Twice you have mentioned that you are using flash One, when you should be using flash 2.0
What Pin code?
Your pin error sounds like you are either using the old Qfil ( its corrupted, and never worked for anyone. ) Or the technician repair rom did not complete. There will be a log file on the PC from Flash 2, not the phone, is port 9008 open in device manager?
There should be no pin code, if qfil was installed, all of your data would be wiped, did you encrypt the phone with 3rd party software?
Are also using the wrong version of Qfil?
Review these additional steps
https://forum.xda-developers.com/showpost.php?p=76100899&postcount=121
tsongming said:
Okay sure, I provided you with a link to the correct files to use. I.E Flash 2.0 and le_zl1_qfil_ufs_fix.zip
Twice you have mentioned that you are using flash One, when you should be using flash 2.0
What Pin code?
Your pin error sounds like you are either using the old Qfil ( its corrupted, and never worked for anyone. ) Or the technician repair rom did not complete. There will be a log file on the PC from Flash 2, not the phone, is port 9008 open in device manager?
There should be no pin code, if qfil was installed, all of your data would be wiped, did you encrypt the phone with 3rd party software?
Are also using the wrong version of Qfil?
Review these additional steps
https://forum.xda-developers.com/showpost.php?p=76100899&postcount=121
Click to expand...
Click to collapse
I am using flashone 2.0 and flashing from your link, the file "le_zl1_qfil_ufs_fix.zip". Port 9008 is open. After three flash in 2.0 flash, I could enter recovery, but when flashing custom rom, a blue screen appeared.
Not enough information, did you follow all of the steps? You can't just flash a Rom after unbricking.
To be clear
You restored the phone, booted into the system, turned on developer options, checked oem unlocking, booted into recovery, and did a factory reset to repair the storage as outlined in my instructions link?
Then booted into the system again, turned on developer options, checked oem unlocking, checked that storage is accurate?
From this point you start over, if your storage issue isn't fixed you will get a blue screen.
After you have perform those steps you should be able to use the all in one tool to check that the bootloader is unlocked, install the latest TWRP, compatible Rom, Gapps and latest magisk.
If you still have issues after all of that. No doubt, its hardware related. It could be one part or several parts. Time to buy a new phone.
Sent from my Pixel XL using XDA Labs
tsongming said:
Not enough information, did you follow all of the steps? You can't just flash a Rom after unbricking.
To be clear
You restored the phone, booted into the system, turned on developer options, checked oem unlocking, booted into recovery, and did a factory reset to repair the storage as outlined in my instructions link?
Then booted into the system again, turned on developer options, checked oem unlocking, checked that storage is accurate?
From this point you start over, if your storage issue isn't fixed you will get a blue screen.
After you have perform those steps you should be able to use the all in one tool to check that the bootloader is unlocked, install the latest TWRP, compatible Rom, Gapps and latest magisk.
If you still have issues after all of that. No doubt, its hardware related. It could be one part or several parts. Time to buy a new phone.
Sent from my Pixel XL using XDA Labs
Click to expand...
Click to collapse
Once we managed to load the system, which hung up after 3 seconds and the whole situation started again. Failed to reload the system or enter recovery. I did all the steps in turn. After the system startup I did not even manage to enter the settings, because it has already hung up and restarted.
miichus said:
Once we managed to load the system, which hung up after 3 seconds and the whole situation started again. Failed to reload the system or enter recovery. I did all the steps in turn. After the system startup I did not even manage to enter the settings, because it has already hung up and restarted.
Click to expand...
Click to collapse
That sucks!
Its either that the partitions are inaccurate or you have hardware problems.
If its partitions, its not something that I have experience with. However, I did find this link; which has instructions for resolving partition issues using the MiniTool Partition Wizard and HDD Raw Copy Tool. https://www.leakite.com/2016/06/revised-how-to-unbrick-qualcomm-android.html
tsongming said:
That sucks!
Its either that the partitions are inaccurate or you have hardware problems.
If its partitions, its not something that I have experience with. However, I did find this link; which has instructions for resolving partition issues using the MiniTool Partition Wizard and HDD Raw Copy Tool. https://www.leakite.com/2016/06/revised-how-to-unbrick-qualcomm-android.html
Click to expand...
Click to collapse
Hi tsongming Where do I get this files ???
* prog_emmc_firehose_8936.mbn (I think for our x720 has to be prog_emmc_firehose_8916.mbn)
* rawprogram0.xml
* patch0.xml
I have seen this procedure on different sites but none of them provide this files
I hope you can help me
Thanks in advance
mavelino said:
Hi tsongming Where do I get this files ???
* prog_emmc_firehose_8936.mbn (I think for our x720 has to be prog_emmc_firehose_8916.mbn)
* rawprogram0.xml
* patch0.xml
I have seen this procedure on different sites but none of them provide this files
I hope you can help me
Thanks in advance
Click to expand...
Click to collapse
They should download automatically, if you follow the instructions on those previous Links . The instructions should show which folders the files are located in.
Luckily, I saved these files the last time I de-bricked someones phone.
Here is the link to my Google Drive: https://drive.google.com/open?id=1mjvi_FR4Xh9QfSg6imMLduQ6p3zP2e_u
See the Thanks button: Click it, send cash or both.
tsongming said:
They should download automatically, if you follow the instructions on those previous Links . The instructions should show which folders the files are located in.
Luckily, I saved these files the last time I de-bricked someones phone.
Here is the link to my Google Drive: https://drive.google.com/open?id=1mjvi_FR4Xh9QfSg6imMLduQ6p3zP2e_u
See the Thanks button: Click it, send cash or both.
Click to expand...
Click to collapse
Noup they do not download automatically (I followed the instructions), I tried flashone tool procedure in a windows 7 computer and did not work (I already tried this a lot of times on to differente laptops with windows 10), I have not tried the qfil procedure because I do not have the files I mentioned before. Please if you have them upload them (* prog_emmc_firehose_8996.mbn* rawprogram0.xml* patch0.xml)
Thanks in advance
mavelino said:
Noup they do not download automatically (I followed the instructions), I tried flashone tool procedure in a windows 7 computer and did not work (I already tried this a lot of times on to differente laptops with windows 10), I have not tried the qfil procedure because I do not have the files I mentioned before. Please if you have them upload them (* prog_emmc_firehose_8996.mbn* rawprogram0.xml* patch0.xml)
Thanks in advance
Click to expand...
Click to collapse
All I have is in the link you just responded to.
if that doesn't work try unpacking the Qfil and and see if you can just extract them.
I will look further when I get back home.
i also have an bricked LEX 3 Pro . i bought it as an X722 but of cause iam not shure . could also be an X720. i can not find the difference.
so Phone has only fastboot.
when i plug in usb cable it just reboot every 10 sec . no charging sreen appears
i flash Qfil, but not helped it stay the same