Pionneer 8227L_Demo cannot be booted by USB - Android Head-Units

I'm using a Pioneer 8227L_Demo unit with
Android: YT9260_AHD_00006_V004_20191109_DSP
Android Version: Android 8.1 Go
XY AUTO: 3.2
DDR: 2G FLASH: 32G
CPU: A7.1.3GHz x 4
MCU1: 3.1 (8227L)
I've downloaded the "Stock android 9 touch firmware version 1" and extracted to a USB Flash Drive (Tried in Root and created folder "XYAUTOGPG") but I couldn't get it load during reboot of unit (I get into the Factory Setting and hit Reboot), for sure I did try to tap repeatedly during the start up but nothing comes out. I've enabled USB Debugs and one thing I'm not sure is should I set the USB Mode "Host" in the Factory Setting?? Currently it is in "Device" mode.
Please help, million thanks.

Anyone can help

Related

Klyde PX4 | PX5 | PX6 head units with MCU CSN2 | CSN2_D | CSN2_8600_D (Android 8/9/10

This thread relates to MCU: CSN2_xxxxx, CSN2_D_xxxxx and CSN2_8600_D_xxxxx for PX4, PX5 and PX6 platforms
This thread is a mirror of russian 4pda to cover more users/developers.
All units are made by Klyde, but are sold under different brands.
I've been looking for a simple way to donate me if this thread is useful for you, all the ways are collected in one post there
The thread requires a new mainteiner. Details are there.
Hardware specifications:
CPU: Octa-core PX5 1.5GHz Cortex A53 64 bits CPU
ROM: 16/32/64G
RAM: 2/4G
Resolution: 1024*600
Out Power: 4*45Watt
Operating System: Android 8/9
Radio Tuner/Audio Chip: NXP6686 / TDA7851
Built-In WiFi Module /Support External 3G Dongle
Features: Radio Tuner,Built-in GPS,MP3 Player,Bluetooth,Touch Screen,TV,Mirror link,Built-In Microphone,Support Steering Wheel Control,Support Can-Bus
Useful tips
Tag [Android 8] means that it applicable to Android 8 , the same for [Android 9]. If there is no tag, it suits both versions.
Factory Settings password: 126
If you type 888 while opening Factory Settings, the Logo changing menu appears instead of Factory Settings. Logo1 replaces "Navigation system" picture, Logo2 replaces "android" picture. Logo2 is animated.
Developers mode password is 237
Password 927 opens menu, that helps to adjust screen brightens by changing VCOM value. You can set it between 1 and 100. Be careful with that!
[Android 8] How to get root: Use a rooting app, alternative link
[Android 9] How to root
Warning! You should be careful with that as it can brick your device once you tried to update SuperSu. Do not update SuperSu binary or the SuperSU app!!! You will get bootloop if that is updated!!! Also you have to wait until the tool completes its job, otherwise you can get no sound. If you face the mentioned problems, just re-flash your device. BE CAREFUL!.
Starting from android 8 January firmware there is an option "OFF" for "Power off delay if ACC OFF". it allows to keep android in a sleep mode forever. Please note that it consumes around ~9-10mA in this mode. Powered off device uses 4.8mA only (twice less than sleeping mode).
How to get enter stock recovery: hold reset(power) button, wait until sensor buttons start blinking, release and immediately press the button again. See video
To adjust the back camera brightness, just tap the screen when the camera is active.
Set custom logo
Detailed device schema
Known issues/limitations and fix/workaround for that
Lost wheel key settings and radio stations in case full power loss (yellow wire). Make sure that yellow wire is not disconnected when the car is stopped/locked.
Sound level is 10 (12) after reboot/sleep if you was listening louder; if it was less than 10 (12) stays the same. 12 appeared in Dec 11th firmware, it was 10 before that. Not topical starting from Dec 27th firmware, now you can define default sound between 12 10 and 20 in Car Settings-->Personal Settings. 10-20 is in Jan 17th firmware .
buzz in speakers caused by 433MHz alarm system and USB stick remounting.
small buzz caused by WIFI, observed in complete silence only. Not an issue if there are no connected devices.
There are lots of cases when wheel keys does not work at all. The reason is in wiring. Please study the head unit manual + car wiring scheme and put the needed wire to the correct connection shoe.
if you have canbus adapter and wheel buttons duplicate actions (i.e you pressed next track, but 2-3 tracks were switched, the same for sound level), just flash Jan 17 or newer firmware. Also it is possible to change wiring, but the firmware is much easier.
if you have canbus adapter and track switching is reversed (incorrect), just go to Factory Settings --> canbus and set keys_previous_next to change.
Bluetooth ODBII and hands-free (calls) does not work simultaneously. At the same time ODBII and BT Music works well simultaneously. Hardware limitation, no idea for now if that can be solved.
Voice dialing, voice search do not work on some devices. Fixed in May 8th firmware.
1.PX5 Firmware.
You can combine different firmware and MCU (I.e. take the pumpkin MCU + April firmware or vice versa). MCU from Android 8 is compatible with Android 9. Mind DSP only while updating MCU.
The factory does not provide me with a changelog! Do not ask about it.
Android 10.
Mar 31st 2021 202103310921
Mar 23rd 2021 202103231402 with Erisin launcher
Jan 4th 2021 202101041604 + MCU CSN2_D_1152020_114303
Fake Android 10.
It is the same android 9 firmware, but with the changed launcher, radio and Bluetooth app.
July 6th 202007061156
Android 9.
The link for the most recent firmware and MCU: with DSP and without DSP. _D_ in the MCU version means that it is for units with DSP.
All available versions of MCU are on my Google drive.
Firmware history and links:
Sep 1st 2020 202009011014
June 1st 202006010933
Android 8.
The link for the most recent firmware and MCU: with DSP and without DSP. _D_ in the MCU version means that it is for units with DSP.
All available versions of MCU are on my Google drive.
Firmware history and links:
June 18th 201906180853 + MCU CSN2_06102019_114308
2. PX6 Firmware
Android 10.
Aug 27th 2021 202108271854
Mar 31st 2021 202103311813
Oct 27th 2020 202010270905
Android 9.
July 1st 202007011143
3. PX5 Android 9 for 1 DIN units with MCU CSN2_8600_D
The differences between this unit are on Russian 4pda
Firmware 201911301053 + MCU CSN2_8600_D_11202019_162651 is located on Google Drive
4. PX4 Firmware
Android 10.
Oct 23rd 2020 202010231137
The instruction how to upgrade is there
The list of purchased devices
KLYDE for Subaru Forester
OTOJETA for Nissan and 3 more for Sportage IV
KANOR 2pcs for Oulander and 2DIN 2Din and 2pcs for Mazda, and for cee'd
SKYSHADOW for hyundai i40, and for Prado, also 2Din with 32Gb and 64Gb
HaiSunny for StantaFe
Eonon GA9180A for Chevrolet/GMC
Autostereo for Mazda 5
Tested and compatible 3G/4G modems
ZTE MF622
ZTE MF825
Huawei e173
Huawei E352
Huawei E3272
Alcatel 410D
How to update firmware on the device (without changing android version)
I know at least 3 methods how to do that Use USB Stick or SD card with FAT32 filesystem for android 8 or USB Stick ONLY for android 9.
1.
- put the firmware (kupdate.zip + update2.bin if you want to upgrade MCU) directly to USB stick or SD card,
- insert it while the unit is running,
- click OK once suggestion to update appears.
2. The same as 1, but the last point is to start update from system settings
3. Use it, if you have a brick (bootloop)
- put the firmware (kupdate.zip + update2.bin if you want to upgrade MCU) directly to USB stick or SD card with FAT32 filesystem for android 8 or ONLY USB Stick for android 9.
- power off the device, insert USB stick or SD card for android 8 or ONLY USB Stick for android 9.
- press and hold power button and power on unit by switching on ACC in your car or enable power +12V on both red and yellow wire in case you doing that on the table. On some units use reset button instead.
- once the update is started, release the button.
WARNING! Firmware update will remove all your personal data and settings on the device!
If you observe the error like "header and footer of kupdate.zip does not correspond signature", just try to upgrade form another USB stick/SD card.
Upgrade from Android 8 to Andriod 9 (Using disassembling method)
For now it is needed to DISASSEMBLE the unit for upgrade! These actions are on your own responsibility!!!
0. You will need Windows PC/Laptop/Tablet for this procedure, please refer to guide from Chinese engineers here.
1. Install drivers from this archive
2. Short circuit the resistor to ground (there is a picture in guide)
3. Power on the unit
4. Connect USB (use Type-A male to Type-A male cable).
5. Flash the Android 9 data from this archive
6. Disconnect USB and power. Then power on the unit.
7. Enjoy
After these steps you'll be able to install any android 9 from this thread. It is needed to disassemble the unit only once.
A few videos for the reference are there and there.
Upgrade from Android 8 to 9 WITHOUT disassembling.
ALL YOUR ACTIONS ARE YOUR OWN RESPONSIBILITY!!! Nobody will send you a new core board in case of the failure! At least will not do that free of charge!
0. All needed files are there.
1. To perform the upgrade we need:
- Strong desire to do that and be ready to purchase a new core board in case of total failure (~100$);
- micro SD card slot in your unit. If the unit vendor gives details regarding the units without SD cards, I'll update this post;
- USB stick (up to 16GB, to avoid possible problems) formatted in fat32;
- micro SD card (again, please use not so big);
2. Put the following things on USB stick:
- MCU firmware that suits your device. I.e. update2.bin from the first message in thread with DSP or not depending on your unit)
- Android 9 firmware from the first message. kupdate.zip, Again: Andriod 9!!!
3. Do NOT plug USB stick to the unit for now, let`s make bootable SD card;
4. On Windows PC run SDDiskTool and create bootable SD card. The manual inside of the archive, with the details, so I see to reasons to repeat it there. update.img from the archive is used there ~350Mb;
5. Install "Android 8 upgrade 9.apk" into the unit, run it, click only the button in this application. The unit becomes a brick (temporary, till a success on step 9) - You will see only a black screen and lights on the buttons;
6. Put SD card into a units slot, disconnect battery terminal of your car or power off the unit in some other way. Both red and yellow wires of unit should not have +12V on them !!!
7. connect battery terminal.
8. The unit is upgraded for the first time. Take a video of the process!!! Just in case if you fail and it will be needed to troubleshoot that. On this step you should see TWO errors of formatting metadata. YES, there should be TWO errors!! and formatting error for system.
Video of attempt.
The final screenshot.
9. Disconnect and connect battery terminal one more time. The unit upgrades from SD card one more time Take a video of the process,just in case. this time there should be no errors with metadata and system!!! The last string should be "Doing Actions succeeded".
Video of 2nd attempt.
The final screenshot.
10. Disconnect battery terminal, REMOVE SD card from unit, plug USB stick prepared on step 2.
11. Connect battery terminal and the unit will complete the upgrade to Android 9.
12. Once the upgrade from USB stick is done, the unit start running Android 9. All further upgrades will be done from USB stick without any additional actions
Video of installing the firmware from USB Stick.
13. FORMAT SD card on your PC, do not use it in unit until it is formatted, just to be safe.
Upgrade to real android 10
There are 2 known ways how to upgrade to android 10.
1. Disassemble your unit and do the same as described there using the files for PX5 or PX6 depending on your platform. Also there is an instruction with pictures in each archive.
2. Without disassembling, but using windows laptop or tablet. Quite simple, but requires lots of checks and preparations. And in worth case scenario you will have to solder to the needed pins of coreboard.
!!! The upgrade is possible on motherboards rev 1.4, 1.5.2 and 1.6 (quite possible that other revisions too, but we have not enough information for now). The mainboards of rev 1.2 require disassembling and soldering additional usb cable!!!
In order to complete the upgrade we need:
- strong desire to do that and be ready to disassemble unit in case of the failure or even purchase a new one.
- USB type A male to type A male cable
- Windows laptop or tablet
Steps to do.
1. Preparation
- check the Bluetooth module that is configured in your unit: System Settings-->Factory Settings-->FUNC-->BT Mode. Note its model somewhere. That will be needed to restore the settings after the upgrade.
- check if you can do an upgrade:
-- install terminal emulator on your unit and run
Code:
dmesg | grep "USB device" | grep using
and note the last time stamp
-- plug USB stick to the first USB (on the panel or into an extender cable)
-- run again
Code:
dmesg | grep "USB device" | grep using
-- if you see something like
Code:
[ 4781.749803] usb 3-1: new high-speed USB device number 16 using usb20_otg
you can use this USB and plug the head unit to your laptop via it using USB male type A to male type A cable. usb20_otg is vital
-- if you see something like
Code:
1-1.3: new high-speed USB device number 5 using ehci-platform
This USB can not be used!
-- repeat the action for the second unit`s USB
-- IF BOTH PORTS DOES NOT HAVE OTG YOU CAN NOT GO FURTHER UNTIL YOU SOLDER THE 3RD CABLE! The instruction is at the end of this post.
- download PX5 or PX6 depending on your platform.
- if you have a display with resolution 1280*720 , download a custom oem.img, it is suitable for both PX5 and PX6;
- extract archive to root directore of drive C: You should have C:\px6_10.0_burntools\ or C:\px5_10.0_burntools\ folder;
- install drivers from DriverAssitant folder;
- in case of PX6 go to C:\px6_10.0_burntools\AndroidTool_Release_v2.71, for PX5 go to C:\px5_10.0_burntools\AndroidTool_Release_v2.71, edit config.ini, replace Selected=1 with Selected=2. That will enable English language for the program;
- if you have 1280*720 display, put the custom file to rockdev\image folder and replace the old one;
- backup all vital data on your head unit;
2. Upgrade
- run AndroidTool.exe
- download and install this APK
- run it and click "Go to Android10", the device will be rebooted and BRICKED. APK kills loader and boot partition!!!
- connect your laptop and head unit via the discovered OTG USB
- AndroidTool should reprt "Found one MASKROM device"
- hit run button;
- wait until the competition.
The unit will be rebooted, data partition will be formated and the unit will be running andriod 10.
3. Post upgrade
- download the most recent firmware
- put it on USB stick
- do an upgrade using this USB stick
Known issues and fixes
1. Bluetooth KD6 does not work on android 10. Replace the module with IVT140 or RF210, maybe it will be fixed in new firmware. Fixed starting from 202011261850
2. In some unique cases the rear camera does not work on android 10 (we suspect that it appears on old mainboard revisions without DSP). Fix is to revert to android 9 or maybe it will be fixed in new firmware. Fixed starting from 202010141730
TIPs.
Mainboards Rev 1.2 do not have USB OTG, so you have to solder the 3d USB cable. Just solder the USB wire to connector A if the mainboard. Pins 63 and 64. 63rd stands for D+, 64th corresponds D-. Do not forget about GND. +5V is not mandatory for upgrade, you can take it from rear connector H (check pin 5 or 10 there) and make fully working USB port.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now we need TWRP and some proper custom ROM support.
February 20th 201902201912 + MCU CSN2_0192019_154914 from Pumpkin ND0294 suitable for us said:
I couldnt download the file, it comes corrupt.
---------- Post added at 01:51 PM ---------- Previous post was at 01:48 PM ----------
In my unit, buzz comes when the radio is off, and the noise seems like the radio was turned on, but in very low volume... Does it happen with you too, guys?
Click to expand...
Click to collapse
aecioms said:
I couldnt download the file, it comes corrupt.
Click to expand...
Click to collapse
Fixing my google drive.
aecioms said:
I couldnt download the file, it comes corrupt.
Click to expand...
Click to collapse
Fixed.
Does this unit permit firmware downgrade?
aecioms said:
Does this unit permit firmware downgrade?
Click to expand...
Click to collapse
If you are talking about downgrade from, let's say, Feb firmware to Dec firmware - it works. If you are looking some exotic android like 6.0, there is no firmware with old android for these units.
Head units RockChip PX5 with MCU CSN2 (Android 8.0.0): discussion, firmware, tips etc
_yuzo_ also add these skyshadow products. I own the 1st one with 64gb upgraded version
1. Adjustable 10.1" IPS Android 8.0 4GB +32GB + 8 Core Car DVD Player GPS Glonass map RDS Radio wifi Bluetooth 2 Din for universal
https://s.click.aliexpress.com/e/bSVJ1e80
Particularly the 64gb free upgraded versions were csn2
2. New IPS 10.1" Android 8.0 4GB +64GB + Octa Core Car DVD Player GPS Glonass map RDS Radio wifi Bluetooth 4.0 2 Din for universal
https://s.click.aliexpress.com/e/cncQMDNQ
Sent from my iPhone using Tapatalk
sambhasanbiswas said:
_yuzo_ also add these skyshadow products. I own the 1st one with 64gb upgraded version
Click to expand...
Click to collapse
Done.
Hi Yuzo. Do you know if there is a way to pull a copy of my existing OS and MCU that came shipped with the unit? I want to try flashing to the latest pumpkin MCU, but would like to restore to stock if needed. My unit is an Eonon GA9180a. Thanks!
Build Number: 201811021951
Kernel: 4.4.103
MCU: CSN2_1122018_153527
Guys, I can't transfer files with ES File explorer by WLAN. It says "sender disconnected"... Does it happen with someone else? How to solve this?
Now I need to use pendrive everytime I want to transfer files to headunit...
rblloyd83 said:
Hi Yuzo. Do you know if there is a way to pull a copy of my existing OS and MCU that came shipped with the unit? I want to try flashing to the latest pumpkin MCU, but would like to restore to stock if needed. My unit is an Eonon GA9180a. Thanks!
Build Number: 201811021951
Kernel: 4.4.103
MCU: CSN2_1122018_153527
Click to expand...
Click to collapse
Hi! Rooting app contains tools for backup, but that is rather alfa version and noone tried to flash that dump back.
Your MCU is present in very first firmware available there. I, as well as xda and 4pda users, do not have 201811021951 firmware. But I can assure that Jan 17th and Pumpkin firmwares are stable. The only noticeable difference between them is in a launcher, application appearance. Also Pumpkin does not have the option that allows to set the brightness according to the clock.
Please also share the link where you bought your device.
_yuzo_ said:
Hi! Rooting app contains tools for backup, but that is rather alfa version and noone tried to flash that dump back.
Your MCU is present in very first firmware available there. I, as well as xda and 4pda users, do not have 201811021951 firmware. But I can assure that Jan 17th and Pumpkin firmwares are stable. The only noticeable difference between them is in a launcher, application appearance. Also Pumpkin does not have the option that allows to set the brightness according to the clock.
Please also share the link where you bought your device.
Click to expand...
Click to collapse
Thanks, sure appreciate the feedback. I purchased this system:
"eonon.com/Android-Car-GPS/Vehicle-Specific-GPS/Chevrolet-GMC-Buick-Newest-Android-8-0-Car-GPS-Navigation-System-7-Inch-Auto-Stereo-Upgrade-RAM-4GB-Factory-Auto-Radio.html"
I just wanted to list my csn2 device that I ordered at aliexpress from seller autostereo for my Mazda 5: https://de.aliexpress.com/item/-/32913733250.html
I did not do any modification so far. But steeringwheel keys do double clicks, so maybe I will try some update later.
rblloyd83 said:
Thanks, sure appreciate the feedback. I purchased this system:
"eonon.com/Android-Car-GPS/Vehicle-Specific-GPS/Chevrolet-GMC-Buick-Newest-Android-8-0-Car-GPS-Navigation-System-7-Inch-Auto-Stereo-Upgrade-RAM-4GB-Factory-Auto-Radio.html"
Click to expand...
Click to collapse
Thanks. Added.
donny02 said:
I just wanted to list my csn2 device that I ordered at aliexpress from seller autostereo for my Mazda 5: https://de.aliexpress.com/item/-/32913733250.html
I did not do any modification so far. But steeringwheel keys do double clicks, so maybe I will try some update later.
Click to expand...
Click to collapse
Added to the list of devices. The case is connected with canbus adapter and fixed in Jan 17th firmware (also it is possible to fix that by changing wires, but firmware update is much easier). If you want to keep the original launcher - use Jan 17th firmware, otherwise you can try Pumpkin.
Eonon GA9180A For Chevy/GM Trucks is running CSN2. Im pretty sure its a klyde as well.
As for the static when D/L U/L over wifi. It because the wifi antenna is taped directly to the top of the am/fm receiver and not properly shielded.
I did buy a new antenna with a longer cable. One of these days i will pull it out of the truck and add the new one in and reroute the wiring to see if it helps any.(not in a rush since it doesn't bother me to much)

[ROOT] Eonon GA9450b spec / mod thread

Hi,
I wanted to start a thread to collect all the information that I've found so far on this unit.
I bought this headunit off of Amazon for my E46 BMW:
https://www.amazon.com/Upgraded-Android-Eonon-Applicable-Camera-9-Inch-GA9450B/dp/B08D6PDN97/
Also available here:
Eonon GA9450B | Eonon BMW 3 Series E46 Android 10 Car Head Unit 9 Inch HD Full Touchscreen Car GPS Navigation with 32G ROM Built-in DSP & Apple Car Auto Play
Eonon BMW 3 Series E46 Android 10 Car Head Unit 9 Inch HD Full Touchscreen Car GPS Navigation with 32G ROM Built-in DSP & Apple Car Auto Play
www.eonon.com
System Information
Model: GA9450B System: Android 10
CPU: MTK 8227L 1.2GHz ARM A7 Quad Core
RAM: 2GB
ROM: 32GB
Language: English/Spanish/French/German/Portuguese/Italian/Russian/Turkish/Norwegian/Japanese and other 85 languages
Function
Built-in Apple CarAuto Play Support Android Auto with Eonon USB dongle A0585(not included)
Supports EasyConnection
Supports most of the steering wheel control functions (switch songs, channels and adjust volume)
Support variable-color button illumination: seven colors
Supports Wi-Fi(2.4G), 4Gdongle (NOT INCLUDED)
IPS 1024x600
DAC TDA7851L 4x45W
From what I've read elsewhere Eonon sources from multiple manufacturers. I believe this specific model is made by XTRONS, but I haven't confirmed that yet.
Compatible with (at least):
- BMW 3 Series 1999-2004 E46 323ci 325ci 330ci 318i 328i 318 338 323 325 328 335 330 M3 3 Series.
Supported Input/Output
Radio Antenna Input *1
GPS Antenna Input *1
Wi-Fi Antenna Input *1
USB Input *2
Micro SD card *1
External Microphone *1
RCA Video Output *2
RCA Audio FR/FL/RR/RL Output
CAM IN Video Input *1
VIDEO IN Video Input *1
AUX Audio R/L Input
Subwoofer Output *1
Firmware shipped on my unit:
HMI: XRCH.D.Q.F.3.04_1.2019.11.29.16.00
MCU: TS907.190518(H)
MEDIA: HC_v.2.0.0_191113_1430(v1.71)
BTV: BT.19.11.12.1200
Kernel Version
Kernel 3.18.79 (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05))
[email protected] #28
Mon Oct 28 14:39:22 CST 2019
Build Number
full_8227L_demo-userdebug 10 O11019 1571038753 userdebug
Custom build version
alps-mp-01.mp5
Codes:
- Change boot Logo: 5678
- Advanced configurations: 8888
Root
Here is the method I used to get root:
1) Enable developer mode.
2) Turn on USB debugging.
3) Follow the rest of the instructions here:
https://forum.xda-developers.com/showpost.php?p=80550729&postcount=100
Thank you @dougdude10 !
Optionally instead of using google drive to transfer the supersu apk you can just sideload it through the abd connection which for me was easier and faster.
Warning: never let SuperSu update the su binary or it will not boot anymore and need to fix via TWRP or flash recovery / update.
Once root was verified I was able to install Viper4Android using this version:
ViPER4Android FX 2.7.0.0 APK Download by Team DeWitt - APKMirror
ViPER4Android FX 2.7.0.0 APK Download by Team DeWitt - APKMirror Free and safe Android APK downloads
www.apkmirror.com
USB OTA update:
- Plug in a FAT32 formated USB pen with the firmware files "8227L-8.bin" and "8227L-8.upd" saved to the root folder (email: support at eonon dot com for the updated firmware files and share with us).
- Unit should detect in 30s and update automatically.
Enter Upgrade Mode :
- Plug in a FAT32 formated USB pen with the firmware files "8227L-8.bin" and "8227L-8.upd" saved to the root folder (ask your seller for the updated firmware files).
- Press reset.
- Keep touching the screen with one finger quickly until "detected" appears in green, recovery now starts.
Recovery / Factory Reset:
- Press reset.
- Keep touching the screen quickly with 5 fingers at the same time until "detected, entering recovery" appears.
- Will enter TWRP or do a factory reset if using the stock recovery and reboot after.
I'm currently working on getting TWRP setup. Without a solid backup or having TWRP setup yet I have been hesitant on trying out other upgrade files. In the meantime I have setup Car Launcher FREE which is a great alternative to the existing launcher. I have not figured out how to access the radio using Car Launcher yet, but I haven't played with it a ton either.
I plan on updating this thread once I have both official and unofficial working updates.
Feel free to share your experiences with this headunit here.
Thanks!
reserved #1
reserved #2
Hello,
I have a GA9450A, with the same processor, and Android 10. How do you manage to activate de developer mode?
Thanks
Just a FYI- Xtrons do not manufacture, they resell/OEM.
marchnz said:
Just a FYI- Xtrons do not manufacture, they resell/OEM.
Click to expand...
Click to collapse
Thanks for this
rceledono said:
Hello,
I have a GA9450A, with the same processor, and Android 10. How do you manage to activate de developer mode?
Thanks
Click to expand...
Click to collapse
Go to Settings, then About, then tap Build number seven times.
pbmurdoc said:
Go to Settings, then About, then tap Build number seven times.
Click to expand...
Click to collapse
I tried that before and did not work, as it is suppose to be blocked. I'll try again and report.
So I'm encountering an issue with the linked instructions...
I get "/system/bin/sh: su command not found" when I try to run SU. I've fiddled a little bit with setprop and though the command works, setting the various properties does not have any affect...
kernel: 3.18.79
Build number: full_8227L_demo-userdebug 10 O11019 1571038753 userdebug
pbmurdoc said:
I have not figured out how to access the radio using Car Launcher yet, but I haven't played with it a ton either.
Click to expand...
Click to collapse
For this, if you go to the Apps page in Car Launcher, in the bottom left click the + and then Show All Apps. on my unit this showed all the built in apps and I was able to create shortcuts to Radio and Bluetooth apps respectively.
Is anyone able to help with the above? It seems i'm not the only one experiencing the issue on the GA9450B
pbmurdoc said:
Hi,
I wanted to start a thread to collect all the information that I've found so far on this unit.
I bought this headunit off of Amazon for my E46 BMW:
https://www.amazon.com/Upgraded-Android-Eonon-Applicable-Camera-9-Inch-GA9450B/dp/B08D6PDN97/
Also available here:
Eonon GA9450B | Eonon BMW 3 Series E46 Android 10 Car Head Unit 9 Inch HD Full Touchscreen Car GPS Navigation with 32G ROM Built-in DSP & Apple Car Auto Play
Eonon BMW 3 Series E46 Android 10 Car Head Unit 9 Inch HD Full Touchscreen Car GPS Navigation with 32G ROM Built-in DSP & Apple Car Auto Play
www.eonon.com
System Information
Model: GA9450B System: Android 10
CPU: MTK 8227L 1.2GHz ARM A7 Quad Core
RAM: 2GB
ROM: 32GB
Language: English/Spanish/French/German/Portuguese/Italian/Russian/Turkish/Norwegian/Japanese and other 85 languages
Function
Built-in Apple CarAuto Play Support Android Auto with Eonon USB dongle A0585(not included)
Supports EasyConnection
Supports most of the steering wheel control functions (switch songs, channels and adjust volume)
Support variable-color button illumination: seven colors
Supports Wi-Fi(2.4G), 4Gdongle (NOT INCLUDED)
IPS 1024x600
DAC TDA7851L 4x45W
From what I've read elsewhere Eonon sources from multiple manufacturers. I believe this specific model is made by XTRONS, but I haven't confirmed that yet.
Compatible with (at least):
- BMW 3 Series 1999-2004 E46 323ci 325ci 330ci 318i 328i 318 338 323 325 328 335 330 M3 3 Series.
Supported Input/Output
Radio Antenna Input *1
GPS Antenna Input *1
Wi-Fi Antenna Input *1
USB Input *2
Micro SD card *1
External Microphone *1
RCA Video Output *2
RCA Audio FR/FL/RR/RL Output
CAM IN Video Input *1
VIDEO IN Video Input *1
AUX Audio R/L Input
Subwoofer Output *1
Firmware shipped on my unit:
HMI: XRCH.D.Q.F.3.04_1.2019.11.29.16.00
MCU: TS907.190518(H)
MEDIA: HC_v.2.0.0_191113_1430(v1.71)
BTV: BT.19.11.12.1200
Kernel Version
Kernel 3.18.79 (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05))
[email protected] #28
Mon Oct 28 14:39:22 CST 2019
Build Number
full_8227L_demo-userdebug 10 O11019 1571038753 userdebug
Custom build version
alps-mp-01.mp5
Codes:
- Change boot Logo: 5678
- Advanced configurations: 8888
Root
Here is the method I used to get root:
1) Enable developer mode.
2) Turn on USB debugging.
3) Follow the rest of the instructions here:
https://forum.xda-developers.com/showpost.php?p=80550729&postcount=100
Thank you @dougdude10 !
Optionally instead of using google drive to transfer the supersu apk you can just sideload it through the abd connection which for me was easier and faster.
Warning: never let SuperSu update the su binary or it will not boot anymore and need to fix via TWRP or flash recovery / update.
Once root was verified I was able to install Viper4Android using this version:
ViPER4Android FX 2.7.0.0 APK Download by Team DeWitt - APKMirror
ViPER4Android FX 2.7.0.0 APK Download by Team DeWitt - APKMirror Free and safe Android APK downloads
www.apkmirror.com
USB OTA update:
- Plug in a FAT32 formated USB pen with the firmware files "8227L-8.bin" and "8227L-8.upd" saved to the root folder (email: support at eonon dot com for the updated firmware files and share with us).
- Unit should detect in 30s and update automatically.
Enter Upgrade Mode :
- Plug in a FAT32 formated USB pen with the firmware files "8227L-8.bin" and "8227L-8.upd" saved to the root folder (ask your seller for the updated firmware files).
- Press reset.
- Keep touching the screen with one finger quickly until "detected" appears in green, recovery now starts.
Recovery / Factory Reset:
- Press reset.
- Keep touching the screen quickly with 5 fingers at the same time until "detected, entering recovery" appears.
- Will enter TWRP or do a factory reset if using the stock recovery and reboot after.
I'm currently working on getting TWRP setup. Without a solid backup or having TWRP setup yet I have been hesitant on trying out other upgrade files. In the meantime I have setup Car Launcher FREE which is a great alternative to the existing launcher. I have not figured out how to access the radio using Car Launcher yet, but I haven't played with it a ton either.
I plan on updating this thread once I have both official and unofficial working updates.
Feel free to share your experiences with this headunit here.
Thanks!
Click to expand...
Click to collapse
Hey pbmurdoc, I am trying to root my very similar unit with the same processor and all, if I sent you my updated firmware from eonon would you be able to modify them for me? My unit is a GA9451B. I can export a more detailed list of settings and such later if needed. Please let me know

[SOLVED] How to update Android version (6, 7, 8, 9) on HU with Allwinner T8 (firmware v9.1.1, v9.2.2, v9.3.1, v9.4.1)

How to update Android version (6, 7, 8, 9) on HU with Allwinner T8 (firmware v9.1.1, v9.2.2, v9.3.1, v9.4.1)​Attention! You can update Android version only from PC!​
Spoiler: Before updating
Get root on the device to save the "private" partition and files from the "/system/etc/goc" folder.
The "private" partition contains the MCU set for your HU (may be empty).
Files from the "/system/etc/goc" folder are needed for the bluetooth module to work.
Watch a video
Spoiler: Install the software on your PC
Drivers
Phoenix Suit v1.10
Spoiler: Driver installation
In PC update mode, connect HU to PC.
1. Open the device manager (Click on the icon my computer with the right mouse button and select device manager or control-device manager)
2. Now in the list that opens, find an unknown device or a device with a yellow question mark. (USB Device (VID_1f3a_PID_efe8))
3. Click on it with the right mouse button and select update driver in the open window, select manual installation or search on this computer, then select installation from the specified location.
4. Click browse and select the Drivers folder. Click select then next. Wait while the system installs the drivers.
Spoiler: Hardware
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Spoiler: Enable Update mode from PC
To enable the firmware Update from PC mode, you need to find out the Hardware ID of your HU on the About device screen.
Spoiler: [About device] screen in my case
On the Car settings screen, select the Reset factory item and enter the password 7890HwID (in my case - 7890203)
"System update now?" press the "OK" button.
HU reboot into Update form PC mode. The screen will be blank. The backlight of the screen will be turned on.
Watch a video
Spoiler: Firmware for Phoenix Suit
Android 6 (v9.1.1...)
Android 7 (v9.2.2...)
Android 8 (v9.3.1...)
Android 9 (v9.4.1...)
Spoiler: The update process
Start Phoenix Suit.
Select the firmware file in Phoenix Suit.
Enable Update form PC mode.
Connect the HU to the PC using a USB cable (only one of the two USB ports in the HU is suitable, you need to determine which one).
Answer "YES" twice to Phoenix Suit questions. It is important!!!
Wait for the update process to complete.
HU will reboot with the selected Android version.
Watch a video
Spoiler: After update
You can update Android to the current one. The current version is looking at 4pda.ru or here.
Get root on the device.
Spoiler: Problems and solutions
Spoiler: Red message [UI unauthorized, please contact the supplier]
Get root on the device.
Edit the file /system/build.prop, parameter "ro.fota.device"
For example:​It was​
Code:
ro.fota.device=JYZC1_0024
Should be​
Code:
ro.fota.device=JYZC1_0000
Or
Update modded firmware from 4pda.ru.​
Spoiler: Bluetooth module does not work
Get root on the device.
Restore saved files from /system/etc/goc folder.
Select the type of bluetooth module (BC-6 or BC-8) in Extra settings (password 123456) - Config Info - [BC-6 or BC-8]
Spoiler: No car model selection in Extra settings-Car choose
Get root on the device.
Restore the saved "private" partition.
Spoiler: Touch buttons don't work
The buttons are configured in Settings-Car settings-Extra settings.
Watch video
Spoiler: Installing the firmware from a PC if you have a BRICK
It is necessary to disassemble HU.
Set HU to update mode from PC by shorting the contacts on the Allwinner T8 board.
Spoiler: Set HU to Update mode from PC if you have a BRICK
Short the contacts on the Allwinner T8 board and turn on the HU.
Wait a few seconds and release the contacts.
HU boot into Update form PC mode. The screen will be blank. The backlight of the screen will be turned on.
Next, see Spoiler: The update process
Every now and then, great posts such as this come along. Well done.
****-jones said:
How to update Android version (6, 7, 8, 9) on HU with Allwinner T8 (firmware v9.1.1, v9.2.2, v9.3.1, v9.4.1)​Attention! You can update Android version only from PC!​
Spoiler: Before updating
Get root on the device to save the "private" partition and files from the "/system/etc/goc" folder.
The "private" partition contains the MCU set for your HU (may be empty).
Files from the "/system/etc/goc" folder are needed for the bluetooth module to work.
Watch a video
Spoiler: Install the software on your PC
Drivers
Phoenix Suit v1.10
Spoiler: Hardware
View attachment 5304847​
Spoiler: Enable Update form PC mode
To enable the firmware Update from PC mode, you need to find out the Hardware ID of your HU on the About device screen.
Spoiler: [About device] screen in my case
View attachment 5304849
On the Car settings screen, select the Reset factory item and enter the password 7890HwID (in my case - 7890203)
"System update now?" press the "OK" button.
HU reboot into Update form PC mode. The screen will be blank. The backlight of the screen will be turned on.
Watch a video
Spoiler: Firmware for Phoenix Suit
Android 6 (v9.1.1...)
Android 7 (v9.2.2...)
Android 8 (v9.3.1...)
Android 9 (v9.4.1...)
Spoiler: The update process
Start Phoenix Suit.
Select the firmware file in Phoenix Suit.
Enable Update form PC mode.
Connect the HU to the PC using a USB cable (only one of the two USB ports in the HU is suitable, you need to determine which one).
Answer "YES" twice to Phoenix Suit questions. It is important!!!
Wait for the update process to complete.
HU will reboot with the selected Android version.
Watch a video
Spoiler: After update
You can update Android to the current one. The current version is looking at 4pda.ru or here.
Get root on the device.
Spoiler: Problems and solutions
Spoiler: Red message [UI unauthorized, please contact the supplier]
Get root on the device.
Edit the file /system/build.prop, parameter "ro.fota.device"
For example:​It was​
Code:
ro.fota.device=JYZC1_0024
Should be​
Code:
ro.fota.device=JYZC1_0000
Or
Update modded firmware from 4pda.ru.​
Spoiler: Bluetooth module does not work
Get root on the device.
Restore saved files from /system/etc/goc folder.
Select the type of bluetooth module (BC-6 or BC-8) in Extra settings (password 123456) - Config Info - [BC-6 or BC-8]
Spoiler: No car model selection in Extra settings-Car choose
Get root on the device.
Restore the saved "private" partition.
Spoiler: Installing the firmware from a PC if you have a BRICK
It is necessary to disassemble HU.
Set HU to update mode from PC by shorting the contacts on the Allwinner T8 board.
Spoiler: Set HU to Update mode from PC if you have a BRICK
View attachment 5304853
Short the contacts on the Allwinner T8 board and turn on the HU.
Wait a few seconds and release the contacts.
HU boot into Update form PC mode. The screen will be blank. The backlight of the screen will be turned on.
Next, see Spoiler: The update process
Click to expand...
Click to collapse
You are amazing....thank you very much
Great information ****, my biggest problem is not being able to root the device so I'm stuck on the original old firmware/android version
To give everyone an update, I managed to successfully install Android 9 by following the tutorial that @****-jones has provided.
the best firmware i have found where everything works and is reasonably responsive and good looking can be found here
Архив из Облака Mail.ru
Вам открыли доступ к файлу. Отправлено с помощью Облако Mail.ru.
cloud.mail.ru
I am curious to know if anyone here can recommend what model I should choose for the attached can bus decoder.
Hello and sorry because I speak very little English and I am using a translator.
Mr. ****-jones thank you for helping others.
Here is my car radio configuration.
How I should do to put android 8.
Thanks a lot for your help.
yv4103 said:
Hello and sorry because I speak very little English and I am using a translator.
Mr. ****-jones thank you for helping others.
Here is my car radio configuration.
How I should do to put android 8.
Thanks a lot for your help.
Click to expand...
Click to collapse
Your HwID is 7. Use the password 789007 to enter the update mode from the PC.
See Spoiler: Enable update mode from PC.
thank you so much ****-jones
It didn't work because I was putting 78907 instead of 789007.
on the other hand with the firmware _TW2 it took a very long time or to detect the usb key now with the _TW2fd I no longer have bluetooth, goc file empty, I could only save the private
I have the goc of my 7.1.2 saved, can it be? but I have to put in root but I have more superuser on android 8
thank you
see here
yv4103 said:
thank you so much ****-jones
It didn't work because I was putting 78907 instead of 789007.
on the other hand with the firmware _TW2 it took a very long time or to detect the usb key now with the _TW2fd I no longer have bluetooth, goc file empty, I could only save the private
I have the goc of my 7.1.2 saved, can it be? but I have to put in root but I have more superuser on android 8
thank you
see here
Click to expand...
Click to collapse
Thread '[ROOTED] How to get root using Magisk for HU (Allwinner T8) with V9.2.2, V9.3.1, V9.4.1' https://forum.xda-developers.com/t/...lwinner-t8-with-v9-2-2-v9-3-1-v9-4-1.3937350/
Hello everyone.
hello ****-jones.
as said above, no bluetooth and no goc file. I installed firmware v9.3.1_20200619_mod_AtlonX2_AKW1-FD and restored bluetooth but no sound but ok by setting bc8 in options.
now i still don't have root access but i have 21a4f59a-0a56-11e8-91c9-971a30d57911 in 5 lines rooted on usb key and then updated system. I have magisk 23.apk installed on the car radio but no root.
or else I don't quite understand how to do it, or we have to use Kaier support tool to boot.img of
21a4f59a-0a56-11e8-91c9-971a30d57911
22e42020-0a56-11e8-abef-631acfb3beab.0
22e42020-0a56-11e8-abef-631acfb3beab.1
22e42020-0a56-11e8-abef-631acfb3beab.2
2516e792-0a56-11e8-8f93-f3371fae028e
not and flash with magisk 23 on the car radio and not by system update?
Otherwise nice interface in this version v9.3.1_20200619_mod_AtlonX2_AKW1-FD.
Thank you
Hello,
I have an Allwinner T8 device with Android 8.1, I would like to be able to update it to Android 9, but the system version it indicates is this: XWQC01D1-O55-1.04.3.1 - BLINK_NETWORK - 20190923
I also put the specifications in case you can help me:
- Allwinner T8 8 cores A7 1.8Ghz and 2G + 32G
- Manufacturer: Allwinner
- Model: T3 p1 eight-core
- Motherboard: exdroid
- Device: t3-p1
- Hardware: sun8iw11p1
- Serial number: 8f010055593543533012e038faac662d
- Android version: 8.1.0 (Oreo)
- Kernel Version: Linux 4.9.118 - Monday July 15 20:21:45 CST 2019
- OS version: XWQC01D1-O55-1.04.3.1 - BLINK_NETWORK - 20190923
- MCU version: STM32-20190828-11-KC1-30
- CAN version: GM-RZ-09-0012-B1
Thank you all.
Blomvisk said:
Hello,
I have an Allwinner T8 device with Android 8.1, I would like to be able to update it to Android 9, but the system version it indicates is this: XWQC01D1-O55-1.04.3.1 - BLINK_NETWORK - 20190923
I also put the specifications in case you can help me:
- Allwinner T8 8 cores A7 1.8Ghz and 2G + 32G
- Manufacturer: Allwinner
- Model: T3 p1 eight-core
- Motherboard: exdroid
- Device: t3-p1
- Hardware: sun8iw11p1
- Serial number: 8f010055593543533012e038faac662d
- Android version: 8.1.0 (Oreo)
- Kernel Version: Linux 4.9.118 - Monday July 15 20:21:45 CST 2019
- OS version: XWQC01D1-O55-1.04.3.1 - BLINK_NETWORK - 20190923
- MCU version: STM32-20190828-11-KC1-30
- CAN version: GM-RZ-09-0012-B1
Thank you all.
Click to expand...
Click to collapse
Doesn't suit you
****-jones said:
Doesn't suit you
Click to expand...
Click to collapse
What a bad luck ...
Hi @****-jones, is there any update for my T8 p1 6 cores, 7 inch screen with 800x480 pixels as the photos?
Thanks,
Unfortunately, during my upgrade process (from V9.2.2_20180120.164839_KED3-5 to 9.4.1 - T8 android 9 for Phoenixsuite: https://disk.yandex.ru/d/b1lLQ2keXM_Mvw), I answerer "YES" only once!
The radio is on bootloop. When turning car power on, pressing reset and immediately turning power off and waiting for 10 sec before powering on again, it can go to recovery update, but I can't find working files to upgrade. Is there a way to unbrick my radio? Thank you so much
alf74 said:
Unfortunately, during my upgrade process (from V9.2.2_20180120.164839_KED3-5 to 9.4.1 - T8 android 9 for Phoenixsuite: https://disk.yandex.ru/d/b1lLQ2keXM_Mvw), I answerer "YES" only once!
The radio is on bootloop. When turning car power on, pressing reset and immediately turning power off and waiting for 10 sec before powering on again, it can go to recovery update, but I can't find working files to upgrade. Is there a way to unbrick my radio? Thank you so much
Click to expand...
Click to collapse
https://forum.xda-developers.com/t/...ng the firmware from a PC if you have a BRICK
****-jones said:
https://forum.xda-developers.com/t/solved-how-to-update-android-version-6-7-8-9-on-hu-with-allwinner-t8-firmware-v9-1-1-v9-2-2-v9-3-1-v9-4-1.4274577/#:~:text=Spoiler: Installing the firmware from a PC if you have a BRICK
Click to expand...
Click to collapse
I have read about another way: IN CASE OF EMERGENCY (bricked): A way to unbrick is to make a link between the KEY1 cable to the METAL BOX (ground) and to reset the headunit. An UPDATE message will appear, then release the KEY1 cable off the ground.
Does it work with phoenix suite or it's the same of resetting, turning power off and waiting for 10 sec and it's only for usb/sd card?
HU boot into Update form PC mode. Very difficult operation.... I've used a needle to ground. Now It works!
Buna ziua si imi pare rau pentru ca vorbesc foarte putina engleza si folosesc un traducator. Dl **** - Jones vă mulțumesc pentru ajutorul altora. Aici este radio masina mea de configurare. Cum ar trebui să fac pentru a pune Android 8. Multumesc mult pentru ajutor.
****-jones said:
How to update Android version (6, 7, 8, 9) on HU with Allwinner T8 (firmware v9.1.1, v9.2.2, v9.3.1, v9.4.1)​Attention! You can update Android version only from PC!​
Spoiler: Before updating
Get root on the device to save the "private" partition and files from the "/system/etc/goc" folder.
The "private" partition contains the MCU set for your HU (may be empty).
Files from the "/system/etc/goc" folder are needed for the bluetooth module to work.
Watch a video
Spoiler: Install the software on your PC
Drivers
Phoenix Suit v1.10
Spoiler: Driver installation
In PC update mode, connect HU to PC.
1. Open the device manager (Click on the icon my computer with the right mouse button and select device manager or control-device manager)
2. Now in the list that opens, find an unknown device or a device with a yellow question mark. (USB Device (VID_1f3a_PID_efe8))
3. Click on it with the right mouse button and select update driver in the open window, select manual installation or search on this computer, then select installation from the specified location.
4. Click browse and select the Drivers folder. Click select then next. Wait while the system installs the drivers.
Spoiler: Hardware
View attachment 5304847​
Spoiler: Enable Update mode from PC
To enable the firmware Update from PC mode, you need to find out the Hardware ID of your HU on the About device screen.
Spoiler: [About device] screen in my case
View attachment 5304849
On the Car settings screen, select the Reset factory item and enter the password 7890HwID (in my case - 7890203)
"System update now?" press the "OK" button.
HU reboot into Update form PC mode. The screen will be blank. The backlight of the screen will be turned on.
Watch a video
Spoiler: Firmware for Phoenix Suit
Android 6 (v9.1.1...)
Android 7 (v9.2.2...)
Android 8 (v9.3.1...)
Android 9 (v9.4.1...)
Spoiler: The update process
Start Phoenix Suit.
Select the firmware file in Phoenix Suit.
Enable Update form PC mode.
Connect the HU to the PC using a USB cable (only one of the two USB ports in the HU is suitable, you need to determine which one).
Answer "YES" twice to Phoenix Suit questions. It is important!!!
Wait for the update process to complete.
HU will reboot with the selected Android version.
Watch a video
Spoiler: After update
You can update Android to the current one. The current version is looking at 4pda.ru or here.
Get root on the device.
Spoiler: Problems and solutions
Spoiler: Red message [UI unauthorized, please contact the supplier]
Get root on the device.
Edit the file /system/build.prop, parameter "ro.fota.device"
For example:​It was​
Code:
ro.fota.device=JYZC1_0024
Should be​
Code:
ro.fota.device=JYZC1_0000
Or
Update modded firmware from 4pda.ru.​
Spoiler: Bluetooth module does not work
Get root on the device.
Restore saved files from /system/etc/goc folder.
Select the type of bluetooth module (BC-6 or BC-8) in Extra settings (password 123456) - Config Info - [BC-6 or BC-8]
Spoiler: No car model selection in Extra settings-Car choose
Get root on the device.
Restore the saved "private" partition.
Spoiler: Touch buttons don't work
The buttons are configured in Settings-Car settings-Extra settings.
Watch video
Spoiler: Installing the firmware from a PC if you have a BRICK
It is necessary to disassemble HU.
Set HU to update mode from PC by shorting the contacts on the Allwinner T8 board.
Spoiler: Set HU to Update mode from PC if you have a BRICK
View attachment 5304853
Short the contacts on the Allwinner T8 board and turn on the HU.
Wait a few seconds and release the contacts.
HU boot into Update form PC mode. The screen will be blank. The backlight of the screen will be turned on.
Next, see Spoiler: The update process
Click to expand...
Click to collapse
Hi I have a problem after updating by Phoenix, I can not assign the side keys in any way in extra settings in the touch area key, I choose start, reserved, I choose, for example, Vol + but if I want to confirm the side key, it does not respond. I uploaded various updates via a pen drive, through Phoenix I uploaded android from 7 to 9 and to no avail, I uploaded various mcu from the pen drive and via extra settings downloading mcu of various car models via wifi and also no result. I know that my unit is Akw because with the version Ked software pops up red text. Is there an option to somehow assign these side keys what to do? because I am already spreading my hand Please help as you can, my friend

Junsun V1 2gb/32gb won't boot update

Hi all,
Trying to update my Junsun headunit with 8227L_8军灿UI03-国外11_v3_20220714 however when plugging the USB into the unit, it won't boot/recognise the .bin & .upd files.
I've tried both USB ports, both ports read the USB, and I can access the files on the headunit through file explorer, however whatever I try I can't get the unit to boot the update.
I've attempted to reset the device using a pin in the reset hole, and also tried with the unit off and turn the key but the unit just boots normally - nothing seems to be working. USB debugging is turned on in developer options.
Any suggestions?
Platform: 8227L_demo
RAM: 2gb
Storage: 32gb
4 core
Did I read somewhere that you need to rename the files to remove the Chinese characters before they will be recognized? I could be wrong but worth a try.

XY AUTO 3518C

Hello People,
I have a XY3518C auto android 9.1, currently it has the XY AUTO 3.0 version, I went through https://file.xygala.com/?lang=en, to download the updates but there was updates only for Android 6.0, and 8.1; however, I downloaded the 8.1 which had the XY AUTO 3.6 version, and then I moved the files to the USB formatted to fat32, when I insert the USB to the USB port of the stereo the usb will give signal, but when I go to the system info the "Android Update" will still be highlighted and unclickable.
I wonder if anyone has any idea how to update my screen, the current UI sucks and I would be so happy if someone would help me to update the UI, or to add themes as an option to my current system.
Many thanks for considering my questions!

Categories

Resources