Seeking sonimxp5800 firehose_8920 file - Essential Phone Questions & Answers

Seeking sonimxp5800 firehose_8920 file
essential-phone :The thread is closed, this is the tested version of the firmware, the key cannot be verified
Code:
C:\Users\x\Desktop\fastboot getvar all
(bootloader) version:0.5
(bootloader) battery-soc-ok:yes
(bootloader) battery-voltage:4157000
(bootloader) variant:QRD eMMC
(bootloader) secure:yes
(bootloader) version-baseband:
(bootloader) version-bootloader:
(bootloader) display-panel:
(bootloader) off-mode-charge:0
(bootloader) charger-screen-enabled:0
(bootloader) max-download-size: 0x1ff00000
(bootloader) partition-type:cache:ext4
(bootloader) partition-size:cache: 0x40000000
(bootloader) partition-type:userdata:ext4
(bootloader) partition-size:userdata: 0x2858d0e00
(bootloader) partition-type:system:ext4
(bootloader) partition-size:system: 0xa0000000
(bootloader) serialno:c3cacaf3
(bootloader) kernel:lk
(bootloader) product:QC_REFERENCE_PHONE
all:
finished. total time: 0.111s
XP5812:/ $ cat /proc/partitions
major minor #blocks name
254 0 524288 zram0
179 0 15388672 mmcblk0
179 1 106496 mmcblk0p1
179 2 1 mmcblk0p2
179 3 8 mmcblk0p3
179 4 512 mmcblk0p4
179 5 512 mmcblk0p5
179 6 512 mmcblk0p6
179 7 512 mmcblk0p7
179 8 2048 mmcblk0p8
179 9 2048 mmcblk0p9
179 10 256 mmcblk0p10
179 11 256 mmcblk0p11
179 12 16384 mmcblk0p12
179 13 1536 mmcblk0p13
179 14 1536 mmcblk0p14
179 15 32 mmcblk0p15
179 16 1536 mmcblk0p16
179 17 16 mmcblk0p17
179 18 11264 mmcblk0p18
179 19 1024 mmcblk0p19
179 20 1024 mmcblk0p20
179 21 65536 mmcblk0p21
179 22 65536 mmcblk0p22
179 23 1024 mmcblk0p23
179 24 2621440 mmcblk0p24
179 25 1048576 mmcblk0p25
179 26 32768 mmcblk0p26
179 27 1024 mmcblk0p27
179 28 512 mmcblk0p28
179 29 32 mmcblk0p29
179 30 262144 mmcblk0p30
179 31 32 mmcblk0p31
259 0 512 mmcblk0p32
259 1 1024 mmcblk0p33
259 2 32768 mmcblk0p34
259 3 512 mmcblk0p35
259 4 4096 mmcblk0p36
259 5 256 mmcblk0p37
259 6 256 mmcblk0p38
259 7 256 mmcblk0p39
259 8 256 mmcblk0p40
259 9 256 mmcblk0p41
259 10 256 mmcblk0p42
259 11 256 mmcblk0p43
259 12 256 mmcblk0p44
259 13 8 mmcblk0p45
259 14 9020 mmcblk0p46
259 15 7636 mmcblk0p47
259 16 5824 mmcblk0p48
259 17 4820 mmcblk0p49
259 18 10576707 mmcblk0p50
179 32 4096 mmcblk0rpmb
253 0 2580508 dm-0
253 1 10576691 dm-1
XP5812:/ $
XP5812:/ $cat /proc/cpuinfo
Processor : AArch64 Processor rev 4 (aarch64)
processor : 0
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 1
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 2
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 3
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
Hardware : Qualcomm Technologies, Inc MSM8920
XP5812:/ $

what is a firehose file? and what is the zip file attached?

nijohnson said:
what is a firehose file? and what is the zip file attached?
Click to expand...
Click to collapse
This looks very interesting! I have a dead essential I can use this on if you can confirm it works!!!

I have a dead one as well. But I have no idea what to do with the file.

nijohnson said:
what is a firehose file? and what is the zip file attached?
Click to expand...
Click to collapse
https://forum.xda-developers.com/showpost.php?p=80465045&postcount=6

nijohnson said:
I have a dead one as well. But I have no idea what to do with the file.
Click to expand...
Click to collapse
Initial Steps
EDL mode refresh firmware

eleotk said:
Initial Steps
EDL mode refresh firmware
Click to expand...
Click to collapse
Initial step #1 - get pasword ((
Does anybody found it?

I can't find password out. Can you just post it directly? Thanks a lot.

One idea.. Has anyone asked Sonim?
They gave me debug images along with flash tools for the XP8 when I asked about a year ago.. Although not as useful as the early (unlockable) debug images provided by eleotk.. Sonim had to verify I was local in the US and it took a few days but was not an issue. We are seeing now that many variations of the debug image exist for the XP8 so I'm sure it's the same case on this XP5812.
They do seem to keep a tighter grip on the XP5s since custom apps require Sonim direct validation/signing but it may be worth a shot since any debug images they provide would have the required mbn file for flashing.
Obviously you need to give them a developer style excuse as they will likely not help if they know your trying to modify the device.
I would ask them myself however the only XP5s I have is a Sprint XP5800 that's working with the ZTE 8920 mbn file. This issue appears unique to the variant I believe? Aside from the XP5823 label - it looks simular on my end.
Code:
XP5823:/ $ su
XP5823:/ # cat /proc/partitions
major minor #blocks name
254 0 524288 zram0
179 0 15388672 mmcblk0
179 1 106496 mmcblk0p1
179 2 1 mmcblk0p2
179 3 8 mmcblk0p3
179 4 512 mmcblk0p4
179 5 512 mmcblk0p5
179 6 512 mmcblk0p6
179 7 512 mmcblk0p7
179 8 2048 mmcblk0p8
179 9 2048 mmcblk0p9
179 10 256 mmcblk0p10
179 11 256 mmcblk0p11
179 12 16384 mmcblk0p12
179 13 1536 mmcblk0p13
179 14 1536 mmcblk0p14
179 15 32 mmcblk0p15
179 16 1536 mmcblk0p16
179 17 16 mmcblk0p17
179 18 11264 mmcblk0p18
179 19 1024 mmcblk0p19
179 20 1024 mmcblk0p20
179 21 65536 mmcblk0p21
179 22 65536 mmcblk0p22
179 23 1024 mmcblk0p23
179 24 2621440 mmcblk0p24
179 25 1048576 mmcblk0p25
179 26 32768 mmcblk0p26
179 27 1024 mmcblk0p27
179 28 512 mmcblk0p28
179 29 32 mmcblk0p29
179 30 262144 mmcblk0p30
179 31 32 mmcblk0p31
259 0 512 mmcblk0p32
259 1 1024 mmcblk0p33
259 2 32768 mmcblk0p34
259 3 512 mmcblk0p35
259 4 4096 mmcblk0p36
259 5 256 mmcblk0p37
259 6 256 mmcblk0p38
259 7 256 mmcblk0p39
259 8 256 mmcblk0p40
259 9 256 mmcblk0p41
259 10 256 mmcblk0p42
259 11 256 mmcblk0p43
259 12 256 mmcblk0p44
259 13 8 mmcblk0p45
259 14 9020 mmcblk0p46
259 15 7636 mmcblk0p47
259 16 5824 mmcblk0p48
259 17 4820 mmcblk0p49
259 18 10576707 mmcblk0p50
179 32 4096 mmcblk0rpmb
253 0 10576691 dm-0
XP5823:/ # cat /proc/cpuinfo
Processor : AArch64 Processor rev 4 (aarch64)
processor : 0
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 1
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 2
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 3
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
Hardware : Qualcomm Technologies, Inc MSM8920
XP5823:/ #
Edit.. Missed the bootloader options. The Sprint variant at least seems to be shipped in an unlocked state with secure boot also disabled. This is likely why it trusts the ZTE mbn file.
Code:
(bootloader) version:0.5
(bootloader) battery-soc-ok:yes
(bootloader) battery-voltage:3745000
(bootloader) variant:QRD eMMC
(bootloader) secure:no
(bootloader) version-baseband:
(bootloader) version-bootloader:
(bootloader) display-panel:
(bootloader) off-mode-charge:0
(bootloader) charger-screen-enabled:0
(bootloader) max-download-size: 0x1ff00000
(bootloader) partition-type:cache:ext4
(bootloader) partition-size:cache: 0x40000000
(bootloader) partition-type:userdata:ext4
(bootloader) partition-size:userdata: 0x2858d0e00
(bootloader) partition-type:system:ext4
(bootloader) partition-size:system: 0xa0000000
(bootloader) model:XP5800
(bootloader) build:5SA.0.2-03-7.1.2-29.03.00
(bootloader) imei:XXXXXXXXXXXXXXX
(bootloader) serialno:XXXXXXXX
(bootloader) kernel:lk
(bootloader) product:QC_REFERENCE_PHONE
all:
finished. total time: 0.030s

Maybe my English is not well written, password: sonimxp5800

smokeyou said:
One idea.. Has anyone asked Sonim?
They gave me debug images along with flash tools for the XP8 when I asked about a year ago.. Although not as useful as the early (unlockable) debug images provided by eleotk.. Sonim had to verify I was local in the US and it took a few days but was not an issue. We are seeing now that many variations of the debug image exist for the XP8 so I'm sure it's the same case on this XP5812.
They do seem to keep a tighter grip on the XP5s since custom apps require Sonim direct validation/signing but it may be worth a shot since any debug images they provide would have the required mbn file for flashing.
Obviously you need to give them a developer style excuse as they will likely not help if they know your trying to modify the device.
I would ask them myself however the only XP5s I have is a Sprint XP5800 that's working with the ZTE 8920 mbn file. This issue appears unique to the variant I believe? Aside from the XP5823 label - it looks simular on my end.
Code:
XP5823:/ $ su
XP5823:/ # cat /proc/partitions
major minor #blocks name
254 0 524288 zram0
179 0 15388672 mmcblk0
179 1 106496 mmcblk0p1
179 2 1 mmcblk0p2
179 3 8 mmcblk0p3
179 4 512 mmcblk0p4
179 5 512 mmcblk0p5
179 6 512 mmcblk0p6
179 7 512 mmcblk0p7
179 8 2048 mmcblk0p8
179 9 2048 mmcblk0p9
179 10 256 mmcblk0p10
179 11 256 mmcblk0p11
179 12 16384 mmcblk0p12
179 13 1536 mmcblk0p13
179 14 1536 mmcblk0p14
179 15 32 mmcblk0p15
179 16 1536 mmcblk0p16
179 17 16 mmcblk0p17
179 18 11264 mmcblk0p18
179 19 1024 mmcblk0p19
179 20 1024 mmcblk0p20
179 21 65536 mmcblk0p21
179 22 65536 mmcblk0p22
179 23 1024 mmcblk0p23
179 24 2621440 mmcblk0p24
179 25 1048576 mmcblk0p25
179 26 32768 mmcblk0p26
179 27 1024 mmcblk0p27
179 28 512 mmcblk0p28
179 29 32 mmcblk0p29
179 30 262144 mmcblk0p30
179 31 32 mmcblk0p31
259 0 512 mmcblk0p32
259 1 1024 mmcblk0p33
259 2 32768 mmcblk0p34
259 3 512 mmcblk0p35
259 4 4096 mmcblk0p36
259 5 256 mmcblk0p37
259 6 256 mmcblk0p38
259 7 256 mmcblk0p39
259 8 256 mmcblk0p40
259 9 256 mmcblk0p41
259 10 256 mmcblk0p42
259 11 256 mmcblk0p43
259 12 256 mmcblk0p44
259 13 8 mmcblk0p45
259 14 9020 mmcblk0p46
259 15 7636 mmcblk0p47
259 16 5824 mmcblk0p48
259 17 4820 mmcblk0p49
259 18 10576707 mmcblk0p50
179 32 4096 mmcblk0rpmb
253 0 10576691 dm-0
XP5823:/ # cat /proc/cpuinfo
Processor : AArch64 Processor rev 4 (aarch64)
processor : 0
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 1
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 2
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 3
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
Hardware : Qualcomm Technologies, Inc MSM8920
XP5823:/ #
Edit.. Missed the bootloader options. The Sprint variant at least seems to be shipped in an unlocked state with secure boot also disabled. This is likely why it trusts the ZTE mbn file.
Code:
(bootloader) version:0.5
(bootloader) battery-soc-ok:yes
(bootloader) battery-voltage:3745000
(bootloader) variant:QRD eMMC
(bootloader) secure:no
(bootloader) version-baseband:
(bootloader) version-bootloader:
(bootloader) display-panel:
(bootloader) off-mode-charge:0
(bootloader) charger-screen-enabled:0
(bootloader) max-download-size: 0x1ff00000
(bootloader) partition-type:cache:ext4
(bootloader) partition-size:cache: 0x40000000
(bootloader) partition-type:userdata:ext4
(bootloader) partition-size:userdata: 0x2858d0e00
(bootloader) partition-type:system:ext4
(bootloader) partition-size:system: 0xa0000000
(bootloader) model:XP5800
(bootloader) build:5SA.0.2-03-7.1.2-29.03.00
(bootloader) imei:XXXXXXXXXXXXXXX
(bootloader) serialno:XXXXXXXX
(bootloader) kernel:lk
(bootloader) product:QC_REFERENCE_PHONE
all:
finished. total time: 0.030s
Click to expand...
Click to collapse
It seems that I should find the Sprint version XP5800 easier, XP5800 is too little information.

Please forgive my lack of knowledge. This file/process is not something that could fix a bricked phone, correct?

nijohnson said:
Please forgive my lack of knowledge. This file/process is not something that could fix a bricked phone, correct?
Click to expand...
Click to collapse
Yes, refill the wrong partition

Essential_Phone 9008 download
1. First you need to install QPST, and then confirm the following files in the QPST installation directory.
D:\Program Files (x86)\Qualcomm\QPST\bin
QFIL.exe
Fhloader.exe
QSaharaServer.exe
1
2
2. The device needs to switch to port 9008.
3 Download official file extract
https://storage.googleapis.com/essential-static/PH1-Images-QP1A.191005.014.zip
4 I will release 4 files and extract them into the official file.
5 Running QFIL
Set to see pictures

@eleotk something ent wrong... (

st.noigel said:
@eleotk something ent wrong... (
Click to expand...
Click to collapse
devicetype:ufs

eleotk said:
Essential_Phone 9008 download
1. First you need to install QPST, and then confirm the following files in the QPST installation directory.
D:\Program Files (x86)\Qualcomm\QPST\bin
QFIL.exe
Fhloader.exe
QSaharaServer.exe
1
2
2. The device needs to switch to port 9008.
3 Download official file extract
https://storage.googleapis.com/essential-static/PH1-Images-QP1A.191005.014.zip
4 I will release 4 files and extract them into the official file.
5 Running QFIL
Set to see pictures
Click to expand...
Click to collapse
I guess I don't understand? I can't get Qsahara to work? I have everything downloaded and my screen is the same as yours?

tha_mechanic said:
I guess I don't understand? I can't get Qsahara to work? I have everything downloaded and my screen is the same as yours?
Click to expand...
Click to collapse
https://forum.xda-developers.com/z5.../restore-stock-image-lock-bootloader-t3888785
https://mirrors.lolinet.com/software/windows/Qualcomm/QPST/

eleotk said:
https://forum.xda-developers.com/z5.../restore-stock-image-lock-bootloader-t3888785
https://mirrors.lolinet.com/software/windows/Qualcomm/QPST/
Click to expand...
Click to collapse
It looks like my PH-1 is completele dead (
P.S. I`ll try ahain with another PC )

St.Noigel said:
It looks like my PH-1 is completele dead (
P.S. I`ll try ahain with another PC )
Click to expand...
Click to collapse
Replace the file, still can't pass my verification, end

Related

SuperCID Guide

I Am Not Responsible For Breaking Your Device, Take Your Own Risks ^__^
Click to expand...
Click to collapse
Hi Folks
Please Follow Below;
To Set SuperCID Or Change Any CID For That Fact;
1. Check you are S-OFF; Follow Moonshine OR Revolutionaries Guide.
2. Reboot Into Bootloader & Check You Are Fastboot USB
3. Type As Below
Code:
fastboot oem writecid 11111111
(Or whatever CID you want to have from the list in the second post)
4. Reboot Into Bootloader Again & Check You Are Fastboot USB
5. Check You Have Your Chosen CID;
Code:
fastboot getvar cid
(This Should Confirm The CID you chose from the list in the second post)
6. Reboot Back To Android By Typing
Code:
fastboot reboot
Files attached in post should anyone be a bit lost
CID List
Description CID
ALL 11111111
BM BM___001
Bouygues-Telecom BOUYG201
Brightstar-SPA BSTAR301
Entel BSTAR306
Tigo BSTAR307
Movistar BSTAR308
Brightstar-PTB BSTAR502
Chunghwa-Taiwan CHT__601
ATT CWS__001
CA_Dave DAVE_001
DCM DOCOM801
DOPOD DOPOD701
Fastweb-IT FASTW401
GOOGLE GOOGL001
H3G-UK H3G__001
H3G-ROI H3G__003
H3G-AT H3G__106
H3G-Italy H3G__402
H3G-DAN H3G__F05
H3G-SWE H3G__G04
HTC-WWE HTC__001
VODA-Africa-South HTC__016
HTC-Australia HTC__023
HTC-EastEurope HTC__032
HTC-Asia-SEA HTC__037
AirTel-India HTC__038
HTC-India HTC__038
HTC-Asia-SEA-WWE HTC__044
HTC-Tesco HTC__052
HTC Israel HTC__K18
HTC-GER HTC__102
HTC-FRA HTC__203
HTC-FRA-Bouygues HTC__247
HTC-FRA-NRJ HTC__249
HTC-SPA HTC__304
HTC-ITA HTC__405
HTC-PTG HTC__506
TWM-TW HTC__621
Asia-HK-CHT HTC__622
HTC-Russia HTC__A07
HTC-Poland HTC__B25
HTC-Czech HTC__C24
HTC-Dutch HTC__E11
HTC-BE HTC__E41
HTC-Denmark HTC__F08
HTC-Sweden HTC__G09
HTC-Norway HTC__H10
HTC-GCC (Gulf Cooperation) HTC__J15
HTC-Turkey HTC__M27
HTC-ELL HTC__N34
HTC-Nor HTC__Y13
Open-Channel HTCCN701
CT HTCCN702
CU HTCCN703
Hutch-Australia HUTCH001
O2-UK O2___001
O2-DE O2___102
Optus-Australia OPTUS001
ORANGE-UK ORANG001
ORANGE-SK ORANG006
ORANGE-PO ORANG008
ORANGE-BE ORANG012
ORANGE-CH-GER ORANG104
ORANGE-AT ORANG113
ORANGE-French ORANG202
ORANGE-CH-FRA ORANG203
ORANGE-ES ORANG309
ORANGE-PL ORANGB10
Rogers ROGER001
SKT_KR SKT__901
SMC-Voda-HK SMCVD001
HTC-Singapore HTC__044
TELEF-Spain TELEF301
Telstra TELST001
TELUS TELUS001
TIM-Italy TIM__401
TMNL T-MOB003
TMCZ T-MOB004
TMUK T-MOB005
TMHR T-MOB006
TMH T-MOB007
TMSK T-MOB008
Era T-MOB009
TMUS T-MOB010
TMD T-MOB101
TMA T-MOB102
TMMK T-MOBL11
CA_Videotron VIDEO001
VIRGIN-UK VIRGI001
VODA-UK VODAP001
VODA-Greece VODAP006
VODA-Swisscom-WWE VODAP015
VODA-Ireland VODAP019
VODA-Australia VODAP021
VODA-New-Zealand VODAP022
VODA-Proximus VODAP024
VODA-SA VODAP026
VODA-Germany VODAP102
VODA-Swisscom-DE VODAP110
VODA-Mobilkom VODAP120
VODA-DE VODAP129
VODA-SFR VODAP203
VODA-Swisscom-FR VODAP212
VODA-Spain VODAP304
VODA-Italy VODAP405
VODA-Swisscom-IT VODAP416
VODA-MTS-RUS VODAPA30
VODA-Portugal VODAPD18
VODA-Netherland VODAPE17
VODA-TR VODAPM27
HTC Australia HTC__039
What CID would HTC_Y13 be?
Theshawty said:
What CID would HTC_Y13 be?
Click to expand...
Click to collapse
HTC__Y13 - Norway I believe / Nordic
Has anyone got dialer issues with super CID enabled?
gianton said:
Has anyone got dialer issues with super CID enabled?
Click to expand...
Click to collapse
Nope , not here,
Enlighten me what seems to be the issue?
Mine is CID-HTC_044
It's for HTC-Asia-SEA-WWE HTC__044 or HTC-Singapore HTC__044 ?
My RUU before using HTC-Asia-SEA-WWE ! !?
Good Guide, I have a question though, now we have s-off and supercid, can we put any cid on our phone for eg my phone came with H3G__001, can I put command for changing it to HTC__001
dryspuri said:
Good Guide, I have a question though, now we have s-off and supercid, can we put any cid on our phone for eg my phone came with H3G__001, can I put command for changing it to HTC__001
Click to expand...
Click to collapse
Yep thats what SuperCID is for it gives you the opportunity to amend you "Region Code" if you want to call it that
wzu7 said:
Mine is CID-HTC_044
It's for HTC-Asia-SEA-WWE HTC__044 or HTC-Singapore HTC__044 ?
My RUU before using HTC-Asia-SEA-WWE ! !?
Click to expand...
Click to collapse
It can mean both have a look at 038 - India
it has the same for 2 x carriers and WWE edition
fkofilee said:
Nope , not here,
Enlighten me what seems to be the issue?
Click to expand...
Click to collapse
Some users with the Dev edition reported after changing to super CID that about an hour later got their dialer disabled and a message of formatting data partition. Reverting to their old CID fixed that.
gianton said:
Some users with the Dev edition reported after changing to super CID that about an hour later got their dialer disabled and a message of formatting data partition. Reverting to their old CID fixed that.
Click to expand...
Click to collapse
Nope nothing on that here... 4.1.2 bug possibly? Or 4.2.2?
fkofilee said:
Nope nothing on that here... 4.1.2 bug possibly? Or 4.2.2?
Click to expand...
Click to collapse
OK great, I think it's device edition related as none other users reported that. Going to revert my CID too. :good:
Don`t want to ruin the Super CID party, but whether we have trie Super CID or not, remains to be seen. It`s true, that both by hex editing the partition or fastboot command now we get Super CID in fastboot, but what is interesting, that when double checking via adb in live system with adb shell getprop "ro.cid", you will still get your original CID. So it seems CID is stored in 2 different locations now and that fastboot forcing the new CID does not fully finish the task.
Try yourself in adb with:
adb shell getprop "ro.cid"
So old CID still hides in one of these...
PHP:
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1
179 2 256 mmcblk0p2
179 3 130671 mmcblk0p3
179 4 1 mmcblk0p4
179 5 16 mmcblk0p5
179 6 256 mmcblk0p6
179 7 15577 mmcblk0p7
179 8 256 mmcblk0p8
179 9 1024 mmcblk0p9
179 10 256 mmcblk0p10
179 11 2048 mmcblk0p11
179 12 2080 mmcblk0p12
179 13 5120 mmcblk0p13
179 14 1024 mmcblk0p14
179 15 1024 mmcblk0p15
179 16 61441 mmcblk0p16
179 17 8190 mmcblk0p17
179 18 32768 mmcblk0p18
179 19 1022 mmcblk0p19
179 20 4096 mmcblk0p20
179 21 4096 mmcblk0p21
179 22 20480 mmcblk0p22
179 23 4 mmcblk0p23
179 24 256 mmcblk0p24
179 25 16 mmcblk0p25
179 26 1280 mmcblk0p26
179 27 64 mmcblk0p27
179 28 1024 mmcblk0p28
179 29 98727 mmcblk0p29
179 30 54270 mmcblk0p30
179 31 76800 mmcblk0p31
179 32 98303 mmcblk0p32
179 33 16384 mmcblk0p33
179 34 16383 mmcblk0p34
179 35 1900543 mmcblk0p35
179 36 655359 mmcblk0p36
179 37 27262976 mmcblk0p37
he_stheone64 said:
Don`t want to ruin the Super CID party, but whether we have trie Super CID or not, remains to be seen. It`s true, that both by hex editing the partition or fastboot command now we get Super CID in fastboot, but what is interesting, that when double checking via adb in live system with adb shell getprop "ro.cid", you will still get your original CID. So it seems CID is stored in 2 different locations now and that fastboot forcing the new CID does not fully finish the task.
Try yourself in adb with:
adb shell getprop "ro.cid"
So old CID still hides in one of these...
PHP:
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1
179 2 256 mmcblk0p2
179 3 130671 mmcblk0p3
179 4 1 mmcblk0p4
179 5 16 mmcblk0p5
179 6 256 mmcblk0p6
179 7 15577 mmcblk0p7
179 8 256 mmcblk0p8
179 9 1024 mmcblk0p9
179 10 256 mmcblk0p10
179 11 2048 mmcblk0p11
179 12 2080 mmcblk0p12
179 13 5120 mmcblk0p13
179 14 1024 mmcblk0p14
179 15 1024 mmcblk0p15
179 16 61441 mmcblk0p16
179 17 8190 mmcblk0p17
179 18 32768 mmcblk0p18
179 19 1022 mmcblk0p19
179 20 4096 mmcblk0p20
179 21 4096 mmcblk0p21
179 22 20480 mmcblk0p22
179 23 4 mmcblk0p23
179 24 256 mmcblk0p24
179 25 16 mmcblk0p25
179 26 1280 mmcblk0p26
179 27 64 mmcblk0p27
179 28 1024 mmcblk0p28
179 29 98727 mmcblk0p29
179 30 54270 mmcblk0p30
179 31 76800 mmcblk0p31
179 32 98303 mmcblk0p32
179 33 16384 mmcblk0p33
179 34 16383 mmcblk0p34
179 35 1900543 mmcblk0p35
179 36 655359 mmcblk0p36
179 37 27262976 mmcblk0p37
Click to expand...
Click to collapse
Well fella you're wrong on that one ^__^
Just done it and it came back "11111111"
However you are right and it has been an issue before :/
Done!
he_stheone64 said:
Don`t want to ruin the Super CID party, but whether we have trie Super CID or not, remains to be seen. It`s true, that both by hex editing the partition or fastboot command now we get Super CID in fastboot, but what is interesting, that when double checking via adb in live system with adb shell getprop "ro.cid", you will still get your original CID. So it seems CID is stored in 2 different locations now and that fastboot forcing the new CID does not fully finish the task.
Try yourself in adb with:
adb shell getprop "ro.cid"
So old CID still hides in one of these...
PHP:
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1
179 2 256 mmcblk0p2
179 3 130671 mmcblk0p3
179 4 1 mmcblk0p4
179 5 16 mmcblk0p5
179 6 256 mmcblk0p6
179 7 15577 mmcblk0p7
179 8 256 mmcblk0p8
179 9 1024 mmcblk0p9
179 10 256 mmcblk0p10
179 11 2048 mmcblk0p11
179 12 2080 mmcblk0p12
179 13 5120 mmcblk0p13
179 14 1024 mmcblk0p14
179 15 1024 mmcblk0p15
179 16 61441 mmcblk0p16
179 17 8190 mmcblk0p17
179 18 32768 mmcblk0p18
179 19 1022 mmcblk0p19
179 20 4096 mmcblk0p20
179 21 4096 mmcblk0p21
179 22 20480 mmcblk0p22
179 23 4 mmcblk0p23
179 24 256 mmcblk0p24
179 25 16 mmcblk0p25
179 26 1280 mmcblk0p26
179 27 64 mmcblk0p27
179 28 1024 mmcblk0p28
179 29 98727 mmcblk0p29
179 30 54270 mmcblk0p30
179 31 76800 mmcblk0p31
179 32 98303 mmcblk0p32
179 33 16384 mmcblk0p33
179 34 16383 mmcblk0p34
179 35 1900543 mmcblk0p35
179 36 655359 mmcblk0p36
179 37 27262976 mmcblk0p37
Click to expand...
Click to collapse
Yes I did what you said and it shows my old CID. Maybe this file stayed there and after a ROM update will go away.
he_stheone64 said:
Don`t want to ruin the Super CID party, but whether we have trie Super CID or not, remains to be seen. It`s true, that both by hex editing the partition or fastboot command now we get Super CID in fastboot, but what is interesting, that when double checking via adb in live system with adb shell getprop "ro.cid", you will still get your original CID. So it seems CID is stored in 2 different locations now and that fastboot forcing the new CID does not fully finish the task.
Try yourself in adb with:
adb shell getprop "ro.cid"
So old CID still hides in one of these...
PHP:
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1
179 2 256 mmcblk0p2
179 3 130671 mmcblk0p3
179 4 1 mmcblk0p4
179 5 16 mmcblk0p5
179 6 256 mmcblk0p6
179 7 15577 mmcblk0p7
179 8 256 mmcblk0p8
179 9 1024 mmcblk0p9
179 10 256 mmcblk0p10
179 11 2048 mmcblk0p11
179 12 2080 mmcblk0p12
179 13 5120 mmcblk0p13
179 14 1024 mmcblk0p14
179 15 1024 mmcblk0p15
179 16 61441 mmcblk0p16
179 17 8190 mmcblk0p17
179 18 32768 mmcblk0p18
179 19 1022 mmcblk0p19
179 20 4096 mmcblk0p20
179 21 4096 mmcblk0p21
179 22 20480 mmcblk0p22
179 23 4 mmcblk0p23
179 24 256 mmcblk0p24
179 25 16 mmcblk0p25
179 26 1280 mmcblk0p26
179 27 64 mmcblk0p27
179 28 1024 mmcblk0p28
179 29 98727 mmcblk0p29
179 30 54270 mmcblk0p30
179 31 76800 mmcblk0p31
179 32 98303 mmcblk0p32
179 33 16384 mmcblk0p33
179 34 16383 mmcblk0p34
179 35 1900543 mmcblk0p35
179 36 655359 mmcblk0p36
179 37 27262976 mmcblk0p37
Click to expand...
Click to collapse
I did what you say, but before being S-OFF and super-cid-ed, i was with HTC__203 CID.
Now verified in fastboot and with your method, both are giving me the same result CID 11111111.
I've to say that i'm on ARHD10.1. Does it affect the manner to obtain the SUPER-CID?...Really don't know.
he_stheone64 said:
Don`t want to ruin the Super CID party, but whether we have trie Super CID or not, remains to be seen. It`s true, that both by hex editing the partition or fastboot command now we get Super CID in fastboot, but what is interesting, that when double checking via adb in live system with adb shell getprop "ro.cid", you will still get your original CID. So it seems CID is stored in 2 different locations now and that fastboot forcing the new CID does not fully finish the task.
Try yourself in adb with:
adb shell getprop "ro.cid"
So old CID still hides in one of these...
PHP:
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1
179 2 256 mmcblk0p2
179 3 130671 mmcblk0p3
179 4 1 mmcblk0p4
179 5 16 mmcblk0p5
179 6 256 mmcblk0p6
179 7 15577 mmcblk0p7
179 8 256 mmcblk0p8
179 9 1024 mmcblk0p9
179 10 256 mmcblk0p10
179 11 2048 mmcblk0p11
179 12 2080 mmcblk0p12
179 13 5120 mmcblk0p13
179 14 1024 mmcblk0p14
179 15 1024 mmcblk0p15
179 16 61441 mmcblk0p16
179 17 8190 mmcblk0p17
179 18 32768 mmcblk0p18
179 19 1022 mmcblk0p19
179 20 4096 mmcblk0p20
179 21 4096 mmcblk0p21
179 22 20480 mmcblk0p22
179 23 4 mmcblk0p23
179 24 256 mmcblk0p24
179 25 16 mmcblk0p25
179 26 1280 mmcblk0p26
179 27 64 mmcblk0p27
179 28 1024 mmcblk0p28
179 29 98727 mmcblk0p29
179 30 54270 mmcblk0p30
179 31 76800 mmcblk0p31
179 32 98303 mmcblk0p32
179 33 16384 mmcblk0p33
179 34 16383 mmcblk0p34
179 35 1900543 mmcblk0p35
179 36 655359 mmcblk0p36
179 37 27262976 mmcblk0p37
Click to expand...
Click to collapse
Mine is saying original CID too, O2___001
Isn't Australia HTC__039?
Sent from my HTC One using Tapatalk 4 Beta

Stock HBoot Partition Table

Here is the stock Partititon Table for HTC One (M7)
Code:
major minor #blocks name
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1 sbl1
179 2 256 mmcblk0p2 sbl2
179 3 130671 mmcblk0p3 pg1fs
179 4 1 mmcblk0p4 ?
179 5 16 mmcblk0p5 board_info
179 6 256 mmcblk0p6 mfg
179 7 15577 mmcblk0p7 pg2fs
179 8 256 mmcblk0p8 sbl2_update
179 9 1024 mmcblk0p9 sbl3
179 10 256 mmcblk0p10 rpm
179 11 2048 mmcblk0p11 tz
179 12 2080 mmcblk0p12 hboot
179 13 5120 mmcblk0p13 sp1
179 14 1024 mmcblk0p14 wifi
179 15 1024 mmcblk0p15 dsps
179 16 61441 mmcblk0p16 adsp
179 17 8190 mmcblk0p17 radio_config
179 18 32768 mmcblk0p18 reserve_1
179 19 1022 mmcblk0p19 misc
179 20 4096 mmcblk0p20 modem_st1
179 21 4096 mmcblk0p21 modem_st2
179 22 20480 mmcblk0p22 devlog
179 23 4 mmcblk0p23 debug_config
179 24 256 mmcblk0p24 pdata
179 25 16 mmcblk0p25 control
179 26 1280 mmcblk0p26 local
179 27 64 mmcblk0p27 extra
179 28 1024 mmcblk0p28 cdma_record
179 29 98727 mmcblk0p29 reserve
179 30 54270 mmcblk0p30 reserve_2
179 31 76800 mmcblk0p31 radio
179 32 98303 mmcblk0p32 ?
179 33 16384 mmcblk0p33 boot
179 34 16383 mmcblk0p34 recovery
179 35 1900543 mmcblk0p35 system
179 36 655359 mmcblk0p36 cache
179 37 27262976 mmcblk0p37 userdata
Now interestingly enough I've found that the Engineering bootloader posted on the DNA forums that is questionably compatible with our device has this partition table:
Code:
major minor #blocks name
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1 sbl1
179 2 256 mmcblk0p2 sbl2
179 3 130671 mmcblk0p3 pg1fs
179 4 1 mmcblk0p4 ?
179 5 16 mmcblk0p5 board_info
179 6 256 mmcblk0p6 mfg
179 7 15577 mmcblk0p7 pg2fs
179 8 256 mmcblk0p8 sbl2_update
179 9 1024 mmcblk0p9 sbl3
179 10 256 mmcblk0p10 rpm
179 11 2048 mmcblk0p11 tz
179 12 2080 mmcblk0p12 hboot
179 13 5120 mmcblk0p13 sp1
179 14 1024 mmcblk0p14 wifi
179 15 1024 mmcblk0p15 dsps
179 16 61441 mmcblk0p16 adsp
179 17 8190 mmcblk0p17 radio_config
179 18 32768 mmcblk0p18 reserve_1
179 19 1022 mmcblk0p19 misc
179 20 4096 mmcblk0p20 modem_st1
179 21 4096 mmcblk0p21 modem_st2
179 22 20480 mmcblk0p22 devlog
179 23 4 mmcblk0p23 debug_config
179 24 256 mmcblk0p24 pdata
179 25 16 mmcblk0p25 control
179 26 1280 mmcblk0p26 local
179 27 64 mmcblk0p27 extra
179 28 1024 mmcblk0p28 cdma_record
179 29 98727 mmcblk0p29 reserve
179 30 21502 mmcblk0p30 reserve_2
179 31 76800 mmcblk0p31 radio
179 32 16384 mmcblk0p32 boot
179 33 16383 mmcblk0p33 recovery
179 34 1900543 mmcblk0p34 system
179 35 655359 mmcblk0p35 cache
179 36 27394048 mmcblk0p36 userdata
As you can see this bootloader is missing our mmcblk0p32. And has slightly different #blocks in the userdata partition and even more different #blocks in the reserve_2 partition.
I was able to put piece together the names for the blacks by using
Code:
fastboot oem listpartition
while in the engineering bootloader. Doing this resulted in:
Code:
(bootloader) [merge_mfg]:(MERGEMFG, 10) block start=0, size=0 (0 KB)
(bootloader) [merge_emmc]:(RAW, 4) block start=0, size=4849663 (2424831 K
(bootloader) B)
(bootloader) [sbl1]:(RAW, 4) block start=1, size=256 (128 KB)
(bootloader) [sbl2]:(RAW, 4) block start=257, size=512 (256 KB)
(bootloader) [pg1fs]:(PGFS, 4) block start=769, size=261342 (130671 KB)
(bootloader) [board_info]:(RAW, 4) block start=262112, size=32 (16 KB)
(bootloader) [rfg_0]:(RAW, 4) block start=442370, size=2048 (1024 KB)
(bootloader) [rfg_1]:(RAW, 4) block start=444418, size=2048 (1024 KB)
(bootloader) [rfg_2]:(RAW, 4) block start=446466, size=2048 (1024 KB)
(bootloader) [rfg_3]:(RAW, 4) block start=448514, size=2048 (1024 KB)
(bootloader) [rfg_4]:(RAW, 4) block start=450562, size=2048 (1024 KB)
(bootloader) [rfg_5]:(RAW, 4) block start=452610, size=2048 (1024 KB)
(bootloader) [rfg_6]:(RAW, 4) block start=454658, size=2048 (1024 KB)
(bootloader) [mdmsmem]:(RAW, 4) block start=456706, size=2045 (1022 KB)
(bootloader) [dzsystem]:(DEZERO, 8) block start=1048577, size=3801086 (19
(bootloader) 00543 KB)
(bootloader) [dzdata]:(DEZERO, 8) block start=6160384, size=54788096 (273
(bootloader) 94048 KB)
(bootloader) [security_record]:(RAW, 1) block start=0, size=0 (0 KB)
(bootloader) [wcnss]:(RAW, 1) block start=0, size=0 (0 KB)
(bootloader) [wimax]:(RAW, 7E01) block start=0, size=0 (0 KB)
(bootloader) [felica]:(RAW, 1) block start=0, size=0 (0 KB)
(bootloader) [udata_wimax]:(RAW, 7E01) block start=0, size=0 (0 KB)
(bootloader) [spcustom]:(RAW, 1) block start=0, size=0 (0 KB)
(bootloader) [fat]:(RAW, C01) block start=0, size=0 (0 KB)
(bootloader) [imc]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [nfc_record]:(EXT3, 8301) block start=0, size=0 (0 KB)
(bootloader) [microp]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [cpld]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [a1026]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [nfc]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [tp]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [cs]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [gauge]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [cir]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [rcdata]:(OTHER, 1) block start=0, size=0 (0 KB)
(bootloader) [mfg]:(RAW, 7301) block start=262145, size=512 (256 KB)
(bootloader) [pg2fs]:(PGFS, 21) block start=262658, size=31155 (15577 KB)
(bootloader) [sbl2_update]:(RAW, 1) block start=293814, size=512 (256 KB)
(bootloader) [sbl3]:(RAW, 4501) block start=294327, size=2048 (1024 KB)
(bootloader) [rpm]:(RAW, 4701) block start=296376, size=512 (256 KB)
(bootloader) [tz]:(RAW, 4601) block start=296889, size=4096 (2048 KB)
(bootloader) [hboot]:(RAW, 4C01) block start=300986, size=4161 (2080 KB)
(bootloader) [sp1]:(RAW, 3401) block start=305148, size=10240 (5120 KB)
(bootloader) [wifi]:(RAW, 3601) block start=315389, size=2048 (1024 KB)
(bootloader) [dsps]:(RAW, 1) block start=317438, size=2048 (1024 KB)
(bootloader) [adsp]:(RAW, 7A01) block start=319487, size=122882 (61441 KB
(bootloader) )
(bootloader) [radio_config]:(RAW, 7401) block start=442370, size=16381 (8
(bootloader) 190 KB)
(bootloader) [reserve_1]:(RAW, 1) block start=458752, size=65536 (32768 K
(bootloader) B)
(bootloader) [misc]:(RAW, 7601) block start=524289, size=2045 (1022 KB)
(bootloader) [modem_st1]:(EXT3, 4A01) block start=526335, size=8192 (4096
(bootloader) KB)
(bootloader) [modem_st2]:(EXT3, 4B01) block start=534528, size=8192 (4096
(bootloader) KB)
(bootloader) [devlog]:(EXT3, 1901) block start=542721, size=40960 (20480
(bootloader) KB)
(bootloader) [debug_config]:(RAW, 1) block start=583682, size=8 (4 KB)
(bootloader) [pdata]:(RAW, 2301) block start=583691, size=512 (256 KB)
(bootloader) [control]:(RAW, 1) block start=584204, size=32 (16 KB)
(bootloader) [local]:(RAW, 1) block start=584237, size=2561 (1280 KB)
(bootloader) [extra]:(RAW, 1) block start=586799, size=128 (64 KB)
(bootloader) [cdma_record]:(RAW, 1) block start=586928, size=2048 (1024 K
(bootloader) B)
(bootloader) [reserve]:(RAW, 1) block start=588977, size=197455 (98727 KB
(bootloader) )
(bootloader) [reserve_2]:(RAW, 1) block start=786433, size=43004 (21502 K
(bootloader) B)
(bootloader) [radio]:(RAW, 7701) block start=829438, size=153601 (76800 K
(bootloader) B)
(bootloader) [boot]:(RAW, 4801) block start=983040, size=32768 (16384 KB)
(bootloader) [recovery]:(RAW, 7101) block start=1015809, size=32767 (1638
(bootloader) 3 KB)
(bootloader) [system]:(EXT3, 8301) block start=1048577, size=3801086 (190
(bootloader) 0543 KB)
(bootloader) [cache]:(EXT3, 8301) block start=4849664, size=1310719 (6553
(bootloader) 59 KB)
(bootloader) [userdata]:(EXT3, 8301) block start=6160384, size=54788096 (
(bootloader) 27394048 KB)
While I was able to use this bootloader for testing. It will not boot an OS in its current form.
And here are two photos I took while in this engineering bootloader:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This engineering bootloader was found at http://forum.xda-developers.com/showthread.php?t=2155214
I do NOT recommend flashing it unless you know what you are doing. This is a true engineering bootloader and it WILL brick your device very easily if you make a mistake.
kozmikkick said:
Here is the stock Partititon Table for HTC One (M7)
Code:
major minor #blocks name
179 0 30535680 mmcblk0
179 1 128 mmcblk0p1 sbl1
179 2 256 mmcblk0p2 sbl2
179 3 130671 mmcblk0p3 pg1fs
179 4 1 mmcblk0p4 ?
179 5 16 mmcblk0p5 board_info
179 6 256 mmcblk0p6 mfg
179 7 15577 mmcblk0p7 pg2fs
179 8 256 mmcblk0p8 sbl2_update
179 9 1024 mmcblk0p9 sbl3
179 10 256 mmcblk0p10 rpm
179 11 2048 mmcblk0p11 tz
179 12 2080 mmcblk0p12 hboot
179 13 5120 mmcblk0p13 sp1
179 14 1024 mmcblk0p14 wifi
179 15 1024 mmcblk0p15 dsps
179 16 61441 mmcblk0p16 adsp
179 17 8190 mmcblk0p17 radio_config
179 18 32768 mmcblk0p18 reserve_1
179 19 1022 mmcblk0p19 misc
179 20 4096 mmcblk0p20 modem_st1
179 21 4096 mmcblk0p21 modem_st2
179 22 20480 mmcblk0p22 devlog
179 23 4 mmcblk0p23 debug_config
179 24 256 mmcblk0p24 pdata
179 25 16 mmcblk0p25 control
179 26 1280 mmcblk0p26 local
179 27 64 mmcblk0p27 extra
179 28 1024 mmcblk0p28 cdma_record
179 29 98727 mmcblk0p29 reserve
179 30 54270 mmcblk0p30 reserve_2
179 31 76800 mmcblk0p31 radio
179 32 98303 mmcblk0p32 ?
179 33 16384 mmcblk0p33 boot
179 34 16383 mmcblk0p34 recovery
179 35 1900543 mmcblk0p35 system
179 36 655359 mmcblk0p36 cache
179 37 27262976 mmcblk0p37 userdata
Click to expand...
Click to collapse
mmcblk0p4 or mmcblk0p32 can be for CIR.
mike1986. said:
mmcblk0p4 or mmcblk0p32 can be for CIR.
Click to expand...
Click to collapse
I could see that for mmcblk0p4 but would seem odd that 32 would be that with it being so large.
Though 32 does seem important as it's missing in the eng hboot and that's the only missing partition that could make it not boot.
Any thoughts on a workaround?
Sent from my HTC One using xda premium
kozmikkick said:
I could see that for mmcblk0p4 but would seem odd that 32 would be that with it being so large.
Though 32 does seem important as it's missing in the eng hboot and that's the only missing partition that could make it not boot.
Any thoughts on a workaround?
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
True, mmcblk0p4 seems better candidate for CIR.
Maybe dzdata for 32?
BTW how comes DNA has EXT3 partitions by default?
mike1986. said:
True, mmcblk0p4 seems better candidate for CIR.
Maybe dzdata for 32?
BTW how comes DNA has EXT3 partitions by default?
Click to expand...
Click to collapse
No clue about DNA. I only have the m7.
The 3rd codeset that I posted is from the eng hboot. It's what I used to figure out the labels for the partitions. Combined with the adb partition list.
It'd be nice if our stock hboot had the fastboot oem listpartitions option.
Sent from my HTC One using xda premium
mike1986. said:
True, mmcblk0p4 seems better candidate for CIR.
Maybe dzdata for 32?
BTW how comes DNA has EXT3 partitions by default?
Click to expand...
Click to collapse
Had some free time. So I dumped 32. And its a completely empty partition. Not sure why they added it to our partition table in final release but it is completely unused.
I also dumped 30. Which I noted to be a bit different in block size between the eng and ship hboots.
This paritition was interesting. There is a lot of memory text as well as text regarding the modem/lte/wdma. I'm thinking this could be a cache partition for the radio? Though I could be easily wrong. May try and get a bump of this partition from butterfly and see what it does on m7.
Also did a hexdiff between the eng and stock hboot. It looks like the stock hboot has all of the commands that the eng hboot has, its just that they aren't unlocked for a SHIP hboot.
One other thing I just noticed on the ENG HBoot is that even though it picks up that my device is M7_UL it assigns it as PN07200 which is for M7_WLS. It should be PN07100.
I believe that this is the reason why it won't boot on OS on our device.
hboots won't work if it fails the assertion of partition tables. A single partition missing or at the very least an incorrect block size on a specific partition. I already worked on this when I ported the engineering hboot of HTC Sensation to Mytouch 4g slide and it took me weeks just reverse engineering the block sizes.
And yeah... The issue I had to solve was only an mismatched block size of the cache partition. Now I don't know how hard it is reverse engineeering it by snipping a single partition and mapping all the partitions above mmcblk0p33 and up. Plus I'm not even sure about the block sizes.
It would be easier if we could at least get the eng hboot of those htc one which was distributed before release.
And ohh messing with it without a jtag box is like walking in a rope crossing a 100meter building lol!
Riyal said:
hboots won't work if it fails the assertion of partition tables. A single partition missing or at the very least an incorrect block size on a specific partition. I already worked on this when I ported the engineering hboot of HTC Sensation to Mytouch 4g slide and it took me weeks just reverse engineering the block sizes.
And yeah... The issue I had to solve was only an mismatched block size of the cache partition. Now I don't know how hard it is reverse engineeering it by snipping a single partition and mapping all the partitions about mmcblk0p33 and up. Plus I'm not even sure about the block sizes.
It would be easier if we could at least get the eng hboot of those htc one which was distributed before release.
And ohh messing with it without a jtag box is like walking in a rope crossing a 100meter building lol!
Click to expand...
Click to collapse
Indeed. I've dug into it a bit. But theres no way I'll flash a modified hboot lol. Quick way to brick for sure!
It did boot once into the off. Not sure how but it did finish loading. Slow as help. I hard booted back into fastboot and reverted hboots.
Sent from my HTC One using xda premium
My thought initially was that it was going to change the partition table sizes automatically like it did on the g2 when flashing the eng desire z hboot on it.
Sent from my HTC One using xda premium
kozmikkick said:
My thought initially was that it was going to change the partition table sizes automatically like it did on the g2 when flashing the eng desire z hboot on it.
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
it would be great if that's the case Maybe then we could implement a real external sdcard with mass usb storage
Riyal said:
it would be great if that's the case Maybe then we could implement a real external sdcard with mass usb storage
Click to expand...
Click to collapse
Doubtful but maybe.
Sent from my HTC One using xda premium
mike1986. said:
True, mmcblk0p4 seems better candidate for CIR.
Maybe dzdata for 32?
BTW how comes DNA has EXT3 partitions by default?
Click to expand...
Click to collapse
Good catch Mike! It would seem that HTC used ext3 during the development phase.
This might just boot if system cache and data are converted to ext3 since that are current ext4
Sent from my HTC One using xda premium
Mmcbk0p4[Extended]
Mmcbk0p4 is extended partition from 4 - mmcblk0p38. Gsm vs CDMA table differs also
Gsm-
System - mmcbl0p35
Boot - mmcblk0p33
On CDMA
Mmcblk0p35 - boot
Mmcblk0p33 - radio
That is why eng hboot on sprint variant won't boot or recognize radio also
mike1986. said:
mmcblk0p4 or mmcblk0p32 can be for CIR.
Click to expand...
Click to collapse
P4 is empty apart from CID and IMEI and one line encrypted bytes.
This partition was used on 2012 One Series phones to hack SCID into the phone as it wasn't protected there. It now seems to be. The CID offset is still the same as on the older phones.
dzdata files might be a filesystem layout for the the data partition, which is P37. Hence the wipe of the sdcard when flashing those images. There is always 3 flavors: 16, 32 and 64 which i assume correspond to available storage sizes. Well that is my explanation of those otherwise pretty odd images.
Cir.img is located in /system/etc after boot and seems to have no partition on its own. Opened with a hex editor it only reveals nicely ordered codes that look like remote control codes for various devices. I do not understand how RUUmode can inject an image file into an existing partition, not flashing a partition. I understand this must be possible as we have seen various OTA's with an upacked system being flashed, yet those use a meta-inf structure to accomplish that, the RUUmode.zips don't. So i am not too sure about cir.img myself.
Hope those thoughts can help you guys a little.
I picked up some vital info here myself and wish to say thanks.
[EDIT]
Here is my partition listing. I added data i found in Post #1, mainly pg2fs and some others that cannot be seen by cat /proc/emmc.
Hope i can help with this a little and thanks again!
https://docs.google.com/spreadsheet/ccc?key=0AjqWaJywIe10dExiQ0gtZmhBQ0F5NmY1V2pJVkMwdkE&usp=sharing
hi all!!, I have a questions
You know if any partition brings USB drivers?
I have a ONE with more than a month with a problem, not at all my PC detects a USB connection, but if I can connect it to the wall to charge it.
And also detects FASTBOOT mode "fastboot flash recovery recovery.img" for example, so I doubt it's any physical damage, since I detect FASTBOOT mode,
Can be damaged any partition with this libs or else?
I have flashed the official RUU and not fixed,
did ruus flashed all partitions?
bovoro said:
hi all!!, I have a questions
You know if any partition brings USB drivers?
I have a ONE with more than a month with a problem, not at all my PC detects a USB connection, but if I can connect it to the wall to charge it.
And also detects FASTBOOT mode "fastboot flash recovery recovery.img" for example, so I doubt it's any physical damage, since I detect FASTBOOT mode,
Can be damaged any partition with this libs or else?
I have flashed the official RUU and not fixed,
did ruus flashed all partitions?
Click to expand...
Click to collapse
There's probably nothing wrong with the phone. Did you try different USB cables and ports? What about downloading and reinstalling the USB drivers? I had a problem with USB and installing the drivers I found on here fixed it.
yes, I've tried usb cable motorola, nokia, samsung, other computers, installing, uninstalling drivers, to no avail, note that part of the problem is constantly entering Car Dock mode, I think I see this behavior with HTC one X and EVOs.
Or the fifth pin is damaged is the mode that detects CAR DOCK.
bovoro said:
yes, I've tried usb cable motorola, nokia, samsung, other computers, installing, uninstalling drivers, to no avail, note that part of the problem is constantly entering Car Dock mode, I think I see this behavior with HTC one X and EVOs.
Or the fifth pin is damaged is the mode that detects CAR DOCK.
Click to expand...
Click to collapse
Hmm... It sounds like your phone's USB port might be damaged... Normally it takes at least a year for that to happen, but I can't see any other reason why your phone have that problem with all computers and cables. The thing that confuses me is that every phone with a broken USB port that I've seen would not charge either, so I don't know why you can still charge and use fastboot with no problems...
It might be time to restore the stock ROM/firmware and send it in...

Do not flash cm12 over 5.1 bootloader/finding the files for qhusb_bulk

THREAD IS NOW AT ->
http://forum.xda-developers.com/nexus-6/general/fix-fix-qhusbbulk-cm12-t3059518
I will help out. I have been reading all the threads about bricking. I have a working phone running skop and elemental. My computer is a little netbook running windows 7 32. I wont have access to it till later though.
Sent from my Nexus 6
Casper34 said:
I will help out. I have been reading all the threads about bricking. I have a working phone running skop and elemental. My computer is a little netbook running windows 7 32. I wont have access to it till later though.
Sent from my Nexus 6
Click to expand...
Click to collapse
sure no problems, i will need some comands to be run, not flashing or anything.
and thanks
opssemnik said:
sure no problems, i will need some comands to be run, not flashing or anything.
and thanks
Click to expand...
Click to collapse
I will PM you when I get near my computer, or can I run them in terminal emulator?
Sent from my Nexus 6
Casper34 said:
I will PM you when I get near my computer, or can I run them in terminal emulator?
Sent from my Nexus 6
Click to expand...
Click to collapse
which you prefer, tho the output will be a bit big
opssemnik said:
which you prefer, tho the output will be a bit big
Click to expand...
Click to collapse
Check PMs
Sent from my Nexus 6
Casper34 said:
Check PMs
Sent from my Nexus 6
Click to expand...
Click to collapse
can you show me the output of:
ls /dev/block
cat /proc/partitions
ls /dev/block/platform
So we just need to flash 5.0 bootloader before we flash cm Roms? can we still flash asop 5.0?
Sent from my Nexus 6 using Tapatalk
kenbrownstone said:
So we just need to flash 5.0 bootloader before we flash cm Roms? can we still flash asop 5.0?
Sent from my Nexus 6 using Tapatalk
Click to expand...
Click to collapse
once you flash the 5.1 bootloader you can not go back to 5.0.x bootloader. i tried and got a motorola error saying mismatch. so if you flash the 5.1 bootloader that's what you're stuck on. what i want to know is, can you still flash a 5.0.x system/boot image even though you're on 5.1 bootloader?
I flashed back to stock other day after running it ..Should that have been affected
Sent from my Nexus 6 using Tapatalk
looking foward to unbricking it. Thanks a lot
opssemnik said:
can you show me the output of:
ls /dev/block
cat /proc/partitions
ls /dev/block/platform
Click to expand...
Click to collapse
Here you go...... this from 5.0.1
Spoiler
[email protected]:/ $ su
[email protected]:/ # ls /dev/block
bootdevice
dm-0
loop0
loop1
loop2
loop3
loop4
loop5
loop6
loop7
mmcblk0
mmcblk0p1
mmcblk0p10
mmcblk0p11
mmcblk0p12
mmcblk0p13
mmcblk0p14
mmcblk0p15
mmcblk0p16
mmcblk0p17
mmcblk0p18
mmcblk0p19
[email protected]:/ # cat /proc/partitions
major minor #blocks name
179 0 30535680 mmcblk0
179 1 114688 mmcblk0p1
179 2 16384 mmcblk0p2
179 3 384 mmcblk0p3
179 4 56 mmcblk0p4
179 5 16 mmcblk0p5
179 6 32 mmcblk0p6
179 7 1024 mmcblk0p7
179 8 256 mmcblk0p8
179 9 512 mmcblk0p9
179 10 500 mmcblk0p10
179 11 4156 mmcblk0p11
179 12 384 mmcblk0p12
179 13 1024 mmcblk0p13
179 14 256 mmcblk0p14
179 15 512 mmcblk0p15
179 16 500 mmcblk0p16
179 17 4 mmcblk0p17
179 18 512 mmcblk0p18
179 19 1024 mmcblk0p19
179 20 1024 mmcblk0p20
179 21 1024 mmcblk0p21
179 22 1024 mmcblk0p22
179 23 16384 mmcblk0p23
179 24 16384 mmcblk0p24
179 25 2048 mmcblk0p25
179 26 32768 mmcblk0p26
179 27 256 mmcblk0p27
179 28 32 mmcblk0p28
179 29 128 mmcblk0p29
179 30 8192 mmcblk0p30
179 31 1024 mmcblk0p31
259 0 2528 mmcblk0p32
259 1 1 mmcblk0p33
259 2 8 mmcblk0p34
259 3 16400 mmcblk0p35
259 4 9088 mmcblk0p36
259 5 16384 mmcblk0p37
259 6 262144 mmcblk0p38
259 7 65536 mmcblk0p39
259 8 1024 mmcblk0p40
259 9 2097152 mmcblk0p41
259 10 27807616 mmcblk0p42
179 32 4096 mmcblk0rpmb
254 0 27807616 dm-0
[email protected]:/ # ls /dev/block/platform
msm_sdcc.1
[email protected]:/ #
Sent from my Nexus 6
My nexus is also bricked after flash cm12 on top of the 5.2 bootloader. I hit reboot in TWRP and the phone shut down and hasn't done anything since. I cannot get anything to show on the screen and my computer is not recognizing it through fastboot or adb commands. I am running Ubuntu if that helps but again, I cannot see the device connected at all. I am starting to think I need to send this in for RMA
Any help is appreciated.
EDIT: When I run "lsusb" command, I get the following line when my phone is plugged in-
Bus 002 Device 006: ID 05c6:9008 Qualcomm, Inc. Gobi Wireless Modem (QDL mode)
Casper34 said:
Here you go...... this from 5.0.1
Spoiler
[email protected]:/ $ su
[email protected]:/ # ls /dev/block
bootdevice
dm-0
loop0
loop1
loop2
loop3
loop4
loop5
loop6
loop7
mmcblk0
mmcblk0p1
mmcblk0p10
mmcblk0p11
mmcblk0p12
mmcblk0p13
mmcblk0p14
mmcblk0p15
mmcblk0p16
mmcblk0p17
mmcblk0p18
mmcblk0p19
[email protected]:/ # cat /proc/partitions
major minor #blocks name
179 0 30535680 mmcblk0
179 1 114688 mmcblk0p1
179 2 16384 mmcblk0p2
179 3 384 mmcblk0p3
179 4 56 mmcblk0p4
179 5 16 mmcblk0p5
179 6 32 mmcblk0p6
179 7 1024 mmcblk0p7
179 8 256 mmcblk0p8
179 9 512 mmcblk0p9
179 10 500 mmcblk0p10
179 11 4156 mmcblk0p11
179 12 384 mmcblk0p12
179 13 1024 mmcblk0p13
179 14 256 mmcblk0p14
179 15 512 mmcblk0p15
179 16 500 mmcblk0p16
179 17 4 mmcblk0p17
179 18 512 mmcblk0p18
179 19 1024 mmcblk0p19
179 20 1024 mmcblk0p20
179 21 1024 mmcblk0p21
179 22 1024 mmcblk0p22
179 23 16384 mmcblk0p23
179 24 16384 mmcblk0p24
179 25 2048 mmcblk0p25
179 26 32768 mmcblk0p26
179 27 256 mmcblk0p27
179 28 32 mmcblk0p28
179 29 128 mmcblk0p29
179 30 8192 mmcblk0p30
179 31 1024 mmcblk0p31
259 0 2528 mmcblk0p32
259 1 1 mmcblk0p33
259 2 8 mmcblk0p34
259 3 16400 mmcblk0p35
259 4 9088 mmcblk0p36
259 5 16384 mmcblk0p37
259 6 262144 mmcblk0p38
259 7 65536 mmcblk0p39
259 8 1024 mmcblk0p40
259 9 2097152 mmcblk0p41
259 10 27807616 mmcblk0p42
179 32 4096 mmcblk0rpmb
254 0 27807616 dm-0
[email protected]:/ # ls /dev/block/platform
msm_sdcc.1
[email protected]:/ #
Sent from my Nexus 6
Click to expand...
Click to collapse
Thanks, im preparing the QPST / Drivers zip, im also looking into the factory images
ccb1208 said:
My nexus is also bricked after flash cm12 on top of the 5.2 bootloader. I hit reboot in TWRP and the phone shut down and hasn't done anything since. I cannot get anything to show on the screen and my computer is not recognizing it through fastboot or adb commands. I am running Ubuntu if that helps but again, I cannot see the device connected at all. I am starting to think I need to send this in for RMA
Any help is appreciated.
EDIT: When I run "lsusb" command, I get the following line when my phone is plugged in-
Bus 002 Device 006: ID 05c6:9008 Qualcomm, Inc. Gobi Wireless Modem (QDL mode)
Click to expand...
Click to collapse
yep, in that mode we need a program that acts as QPST (or QPST itself) a 2nd_loader.hex (new bootloader) and a APQ8974_image hex that matches ours nexus 6, once there we can send the basic stuff and get rsd mode / fastboot to work, then we just flash factory images
Your best bet would be to try the Moto X/G blankflash program. It uses an executable called qboot which is a USB loader. It may be possible to use the 8226 programmer to flash the bootloader image back to the device from bulk mode. I'd doubt it'd work, but worth checking out.
freebee269 said:
once you flash the 5.1 bootloader you can not go back to 5.0.x bootloader. i tried and got a motorola error saying mismatch. so if you flash the 5.1 bootloader that's what you're stuck on. what i want to know is, can you still flash a 5.0.x system/boot image even though you're on 5.1 bootloader?
Click to expand...
Click to collapse
Yes, you can go back to the 5.0.x system after updating to 5.1
I just flashed the ENTIRE 5.0.1 factory image, minus the bootloader.
You must obviously already be bootloader unlocked to do so.
No ill-effects whatsoever.
If you do go back to 5.0.x, make sure you flash the radio for it as well. There's a chance you'll not be able to receive calls if on LTE with 5.1's radio, as was the case for me. Only on 3g/4g did calls go through (I'm on TMO, btw)
I had the same calls issue on T-Mobile, I was on a 5.0.2 ROM and had flashed the 5.1 bootloader and radio and a friend said she called me but I didn't get a call. When she came over I had her call me again but got nothing, I could call her though. I booted to a 5.1 rom and had her call me and my phone rang.
Hey I have a fully working N6 running stock 5.1, what can I do to help?
opssemnik said:
can you show me the output of:
ls /dev/block
cat /proc/partitions
ls /dev/block/platform
Click to expand...
Click to collapse
swimdude1120 said:
Hey I have a fully working N6 running stock 5.1, what can I do to help?
Click to expand...
Click to collapse
Run those commands if you are rooted and quote opssemnik, the one with the commands, so he can see them.
If you do, put the word SPOILER in brackets [] and then the output, the /SPOILER in the brackets []
Sent from my Nexus 6

*DEV* D6603 Stock Partition Table

Here is the stock partition table from the Xperia Z3 D6603
Code:
major minor #blocks name
253 0 524288 zram0
179 0 15388672 mmcblk0
179 1 2048 mmcblk0p1 TA
179 2 512 mmcblk0p2 sbl1
179 3 256 mmcblk0p3 s1sbl
179 4 64 mmcblk0p4 dbi
179 5 512 mmcblk0p5 aboot
179 6 512 mmcblk0p6 rpm
179 7 512 mmcblk0p7 tz
179 8 512 mmcblk0p8 alt_sbl1
179 9 512 mmcblk0p9 alt_s1sbl
179 10 64 mmcblk0p10 alt_dbi
179 11 512 mmcblk0p11 alt_aboot
179 12 512 mmcblk0p12 alt_rpm
179 13 512 mmcblk0p13 alt_tz
179 14 20480 mmcblk0p14 boot
179 15 10240 mmcblk0p15 ramdump
179 16 16384 mmcblk0p16 FOTAKernel
179 17 32 mmcblk0p17 DDR
179 18 16384 mmcblk0p18 LTALabel
179 19 1536 mmcblk0p19 modemst1
179 20 1536 mmcblk0p20 modemst2
179 21 1536 mmcblk0p21 fsg
179 22 8192 mmcblk0p22 apps_log
179 23 2609152 mmcblk0p23 system
179 24 204800 mmcblk0p24 cache
179 25 12359663 mmcblk0p25 userdata
179 32 4096 mmcblk0rpmb ?
179 64 31260672 mmcblk1 ?
179 65 31256576 mmcblk1p1 ?
This partition table may also work for the D6633, D6653, and D6616. But not having these devices I do not know.
I think mmcblk1 is SD card. Mine has two partitions and I have mmcblk1p2 too.

Elephone P9000 Partition Layout

Partition Layout for Elephone P9000
Code:
major minor #blocks name fsname
7 0 1254 loop0
7 1 32768 loop1 su
254 0 1988256 zram0
179 0 30535680 mmcblk0
179 1 16384 mmcblk0p1 recovery
179 2 512 mmcblk0p2 para
179 3 10240 mmcblk0p3 expdb
179 4 1024 mmcblk0p4 frp
179 5 256 mmcblk0p5 ppl
179 6 32768 mmcblk0p6 nvdata
179 7 32768 mmcblk0p7 metadata
179 8 8192 mmcblk0p8 protect1
179 9 12512 mmcblk0p9 protect2
179 10 8192 mmcblk0p10 seccfg
179 11 8192 mmcblk0p11 oemkeystore
179 12 3072 mmcblk0p12 proinfo
179 13 24576 mmcblk0p13 md1img
179 14 4096 mmcblk0p14 md1dsp
179 15 3072 mmcblk0p15 md1arm7
179 16 5120 mmcblk0p16 md3img
179 17 5120 mmcblk0p17 nvram
179 18 1024 mmcblk0p18 lk
179 19 1024 mmcblk0p19 lk2
179 20 16384 mmcblk0p20 boot
179 21 8192 mmcblk0p21 logo
179 22 5120 mmcblk0p22 tee1
179 23 5120 mmcblk0p23 tee2
179 24 6144 mmcblk0p24 secro
179 25 10240 mmcblk0p25 keystore
179 26 2621440 mmcblk0p26 system
179 27 442368 mmcblk0p27 cache
179 28 27226095 mmcblk0p28 userdata
179 29 16384 mmcblk0p29 flashinfo
179 96 4096 mmcblk0rpmb
179 64 4096 mmcblk0boot1
179 32 4096 mmcblk0boot0
179 128 31166976 mmcblk1
179 129 31162004 mmcblk1p1
Code:
Model: MMC RX14MB (sd/mmc)
Disk /dev/block/mmcblk0: 31.3GB
Sector size (logical/physical): 512B/512B
Partition Table: gpt
Number Start End Size File system Name Flags
1 32.8kB 16.8MB 16.8MB recovery
2 16.8MB 17.3MB 524kB para
3 17.3MB 27.8MB 10.5MB expdb
4 27.8MB 28.9MB 1049kB frp
5 28.9MB 29.1MB 262kB ppl
6 29.1MB 62.7MB 33.6MB ext4 nvdata
7 62.7MB 96.2MB 33.6MB metadata
8 96.2MB 105MB 8389kB ext4 protect1
9 105MB 117MB 12.8MB ext4 protect2
10 117MB 126MB 8389kB seccfg
11 126MB 134MB 8389kB oemkeystore
12 134MB 137MB 3146kB proinfo
13 137MB 163MB 25.2MB md1img
14 163MB 167MB 4194kB md1dsp
15 167MB 170MB 3146kB md1arm7
16 170MB 175MB 5243kB md3img
17 175MB 180MB 5243kB nvram
18 180MB 181MB 1049kB lk
19 181MB 182MB 1049kB lk2
20 182MB 199MB 16.8MB boot
21 199MB 208MB 8389kB logo
22 208MB 213MB 5243kB tee1
23 213MB 218MB 5243kB tee2
24 218MB 224MB 6291kB secro
25 224MB 235MB 10.5MB keystore
26 235MB 2919MB 2684MB ext4 system
27 2919MB 3372MB 453MB ext4 cache
28 3372MB 31.3GB 27.9GB ext4 userdata
29 31.3GB 31.3GB 16.8MB flashinfo

Categories

Resources