If anyone needs this, here is BND-L24 Board Firmware, IDT Flash Tool, Drivers, and Instructions to enter EDL Mode and Flash the board software
**Flashing Board Software should be a final option. If you are still able to flash/boot into TWRP, HuRu or HWOTA would be a better option**
Download :https://drive.google.com/file/d/108uEQyCBMQSywCTOB2c7p9cz35dv_UP9/view?usp=sharing
Image I forgot to add to archive: https://drive.google.com/file/d/1bp_pqu-1HGLyxzsO5c7OEEfCmGjahz-O/view?usp=sharing
1.) Take Back Cover Off Phone (Watch a disassembly video from youtube for the Honor 7X if you do not know how)
Basically you use a guitar pick or pry tool around the edges
2.) Unscrew the plate above the battery and take it off
3.) Under the plate you took off, there should be a black connector for the battery, use tweezers or something to take that off
4.) Plug USB into either computer or phone, but not both
5.) place the tips of the tweezers to the 2 Short Points ( See Image )
6.) reattach battery connector
7.) While holding the 2 short points with tweezers, plug the phone into your computer
8.) Check Device Manager that your Phone is detected as COM Port
9.) Open IDT
10.) Add the Board Firmware .xml
11.) Press Start
12.) Put the dload folder on a SD Card and insert it into your phone
13.) Once your phone starts, in one of the manufacturer apps, there is an option for SD Card Update
14.) Once that's installed, you can now use HuRu, FunkyHuawei, DCPhoneix or whatever you prefer to go to stock firmware
THANK YOU! This helped a ton, I was in quite the situation! Black screen and only fastboot. But now I have neither so i have to do it again. Is there any chance you have the firmware for Nougat? That would be nice, as the current one is Ice Cream Sandwich.
Awesome!
---------- Post added at 08:07 AM ---------- Previous post was at 08:06 AM ----------
THANK YOU! This helped a ton, I was in quite the situation! Black screen and only fastboot. But now I have neither so i have to do it again. Is there any chance you have the firmware for Nougat? That would be nice, as the current one is Ice Cream Sandwich.
Awesome!
---------- Post added at 08:18 AM ---------- Previous post was at 08:07 AM ----------
Nevermind, I just realized the dload file you included is what i was looking for xD. And here I was trying to manually root with adb shell to somehow flash nougat from the OS. A very roundabout way to go about it i know, but there was that image verify thing...heh.
Thanks! This really helped.
Quick question, how did you get the crc files for each partition? Also can they be edited?
IMAGE Download Software - IDTML01Ver1001
Hi, I'm trying to flash board firmware for my hard bricked Huawei Mate 9 (MHA-L29C636) using IMAGE Download Software - IDTML01Ver1001.
I can't seem to flash the firmware. I got this error message by using either "HLMHAAL00AM00A073.xml" or "update_nv_rback.xml"
"Log begin 2020.08.15 03:55:23
Usb com download begin.
Download bootloader[1] begin
The address is: 20000
Download error: 4, 0
Download error: 4, 0
Download error: 4, 0
Download end with cause: 0
Download switch to fastboot.
Download error: 1, 259"
FAIL (4s). Error (4)
Am I doing something wrong here? Please let me know I need to have my phone fix asap for my online class. Thank you very much in advance.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
kylle.tagle14 said:
Hi, I'm trying to flash board firmware for my hard bricked Huawei Mate 9 (MHA-L29C636) using IMAGE Download Software - IDTML01Ver1001.
I can't seem to flash the firmware. I got this error message by using either "HLMHAAL00AM00A073.xml" or "update_nv_rback.xml"
"Log begin 2020.08.15 03:55:23
Usb com download begin.
Download bootloader[1] begin
The address is: 20000
Download error: 4, 0
Download error: 4, 0
Download error: 4, 0
Download end with cause: 0
Download switch to fastboot.
Download error: 1, 259"
FAIL (4s). Error (4)
Am I doing something wrong here? Please let me know I need to have my phone fix asap for my online class. Thank you very much in advance.
Click to expand...
Click to collapse
This tutorial is for the Honor 7x and the Huawei Mate SE. I'm guessing the errors you're getting are because your device isn't compatible with this firmware. Sorry about that.
Kr1msonReaper said:
This tutorial is for the Honor 7x and the Huawei Mate SE. I'm guessing the errors you're getting are because your device isn't compatible with this firmware. Sorry about that.
Click to expand...
Click to collapse
Yes sir, I'm aware that this tutorial is for Honor 7x, as a matter of fact, I've downloaded the board firmware files compatible with my device which is "HLMHAAL00AM00A073 Board Software general 7.0.0 r1 EMUI5.0 05021YVS".
What I did was I extract the .ef file using easy firmware extractor then I run IDT v.2.0.0. I have no idea what's the problem here.
This is the new error I got after using update_nv_rback.xml
"usb1:Start downloading with VCom!
usb1pening COM4 Success
usb1:download mode enter:37
usb1ownloading xloader begin.
usb1:SendFrameRcvAck: Send Fail.
usb1:SendFrameRcvAck: Send Fail.
usb1:SendFrameRcvAck: Send Fail.
usb1:SendFrameRcvAck: Send Fail.
usb1:SendFrameRcvAck: Send Fail.
usb1ownloading xloader : send frame fail.
usb1:[DETAIL_ERROR_CODE] :4
usb1:Midway download fail
FAIL (47 s). Error (4)".
Hoping for your recommendation. I'm so hopeless. </3
I'm sorry I can't be very helpful. I'm 17 and I've never had your device. Some things I would try would be to make sure that the phone is directly connected to the PC ( No multi-usb bus extensions ). Other than that I'm not sure what to say to help you.
Kr1msonReaper said:
I'm sorry I can't be very helpful. I'm 17 and I've never had your device. Some things I would try would be to make sure that the phone is directly connected to the PC ( No multi-usb bus extensions ). Other than that I'm not sure what to say to help you.
Click to expand...
Click to collapse
Did you guys have an ADB device detected in your device manager together with HUAWEI USB COM 1.0 (COM X), or it should detect only the HUAWEI USB COM 1.0 (COM X) when the device is plugged-in using USB?
Because in my case, my laptop can't detect any ADB device, it only detects HUAWEI USB COM 1.0 (COM X).
Do I need to have both drivers detected first, to prevent any error in using the IDT Software tool?
kylle.tagle14 said:
Did you guys have an ADB device detected in your device manager together with HUAWEI USB COM 1.0 (COM X), or it should detect only the HUAWEI USB COM 1.0 (COM X) when the device is plugged-in using USB?
Because in my case, my laptop can't detect any ADB device, it only detects HUAWEI USB COM 1.0 (COM X).
Do I need to have both drivers detected first, to prevent any error in using the IDT Software tool?
Click to expand...
Click to collapse
I'm not sure. I know my PC detected both though so maybe it's worth a try.
I have used this method in my hardbricked honor 7x BND-L22. But i have lost my imei.......
I'm guessing either the flasher is incompatible with your phone, the firmware is incompatible with your phone, or maybe you're just flashing it incorrectly. I'm no expert though, can't help you there, sorry.
May i ask for firmware file reupload ?
(I'm looking for board firmware package with .xml file inside and i"m unable to find it by Google)
mrmotaba said:
May i ask for firmware file reupload ?
(I'm looking for board firmware package with .xml file inside and i"m unable to find it by Google)
Click to expand...
Click to collapse
I will upload a copy shortly, I'm ultra compressing it right now. Mine includes the XML. I wish you luck!
I have hope i will be able to revive this phone.
In worst case scenario i will have to buy some credits from CDU and flash it by their app
mrmotaba said:
I have hope i will be able to revive this phone.
In worst case scenario i will have to buy some credits from CDU and flash it by their app
Click to expand...
Click to collapse
Nice. Lol, I ultra compressed the folder which took about an hour, and now I'm uploading it to mega.nz where it's going REALLY slowly. It's literally 8% uploaded been at it a while.
Kr1msonReaper said:
Nice. Lol, I ultra compressed the folder which took about an hour, and now I'm uploading it to mega.nz where it's going REALLY slowly. It's literally 8% uploaded been at it a while.
Click to expand...
Click to collapse
I bet i will download this file in less than 10 minutes with my super speed 30Mbps LTE
How's the upload going?
mrmotaba said:
I bet i will download this file in less than 10 minutes with my super speed 30Mbps LTE
How's the upload going?
Click to expand...
Click to collapse
Alright, I literally had to leave it overnight, sorry for the wait. Here's the link:
2.44 GB file on MEGA
mega.nz
Thank You very very much...
Im downloading the file and i will try to revive this phone.
mrmotaba said:
Thank You very very much...
Im downloading the file and i will try to revive this phone.
Click to expand...
Click to collapse
Yep, no problem! Good luck!
Hi guys. After flashing board software, my phone boots to a strange Android 5 version with kinds of developper apps. I was running Android 8 before my phone bricks.
How can I go back to Android 8 or to a custom firmware ? When I try to flash the stock rom for my phone, the phone get stuck on boot loop.
Another problem is that recovery mode is in chinese, any idea of how to change back to english?
Related
I will support this method. Please note that the following are UNOFFICIAL steps and these will not be supported officially...So don't mention about this to Customer Care
xdafirmware.com posted two CPBs for Yureka & Yureka Plus & claimed that it is possible to flash them using YGDP. I don't have any bricked one near by, so can you please check?
Flashed a Yureka Plus via fastboot & it looks ok: http://pastebin.com/RtCSQCB7
Click to expand...
Click to collapse
Thanks to @Titokhan for reporting and Testing.
Here is the link for Yureka: http://xdafirmware.com/yu-yureka-ao5510
This method has been shared by DoomLord. Please note that the following are UNOFFICIAL steps and these will not be supported officially...So don't mention about this to Customer Care
Setting up
Step 1] Install QPST (2.7.422) tool - We will be using the QFIL tool which is part of QPST package
Step 2] Install the Qualcomm Download Mode Driver 9008 on Windows PC
The required drivers are in the folder QualcommDownloadModeDriver_9008
For 32-bit Windows OS open Allx86 & double click on dpinst32.exe to start the driver installer (accept all prompts)
For 64-bit Windows OS open Allx64 & double click on dpinst32.exe to start the driver installer (accept all prompts)
Boot YUREKA to Qualcomm HS-USB QDLoader 9008 mode
Note: This is a forced Download mode which is different from normal mode, so this is a must step !
Step 1] Power off the device/remove the battery and the re-insert after few seconds.
Step 2] Open the back cover, unscrew all the screws for the inner cover. Pry open the inner cover to expose the 6 tap points next to the headset plug.
Step 3] With the battery connected, short the top two tap points on the right side, This is illustrated in the attached image.
Step 4] With the two tap points shorted, plugin the USB cable. The device will enter (9008) QDL mode. If the Qualcomm driver is installed correctly, the device will show up as a serial device.
Flashing YUREKA Hard-brick Recovery files in Qualcomm HS-USB QDLoader 9008 mode
Note: The files needed for low level device recovery are in the YUREKA_Bootloader_Recovery folder, keep the folder in root of any drive (because: there shouldn't be any space in folder location).
Step 1] Open the QFIL tool, if you complete previous steps correctly, it will detect the device as: Qualcomm HS-USB QDLoader 9008 (COMx)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 2] In Select Programmer path browser to the folder with those files and select: prog_emmc_firehose_8936.mbn
Step 3] The Select Build section will automatically select the base folder with those files
Step 4] Now click on Load XML
Step 4a] First you will be asked to select the RawProgram file, browse to the folder with those files and select rawprogram0.xml
Step 4b] Next you will be asked to select the Patch file, browse to the folder with those files and select patch0.xml
Step 5] Finally click on “Download” to start the flashing process.
Keep watching the Status log, After flashing is over the following status log will be shown:
PATCH: Partition 0, Sector: 1, Offset 16 Bytes, Size: 4 Bytes, Value: CRC32(1,92)
PATCH: Partition 0, Sector: 0, Offset 16 Bytes, Size: 4 Bytes, Value: 0
PATCH: Partition 0, Sector: 0, Offset 16 Bytes, Size: 4 Bytes, Value: CRC32(NUM_DISK_SECTORS-1.,92)
Total download file size: 52.9502MB
Throughput: 10.59004M/s
Reset Phone
Waiting for reset done...Step 6] The device will now boot and get stuck at the YU boot logo! The device will be continuously vibrating
Congratulations the device is now revived!
Step 7] Close the QFIL program, Disconnect the device and remove the battery for few seconds
Step 8] Reinsert the battery and now keeping the VOLUME UP button pressed connect device to PC – this will trigger FASTBOOT mode
Step 9] Now flash Lollipop (64-bit) factory images via fastboot!
Thanks to:
DooMLoRD for the Actual process.
tirta.agung and
XDAReserved
You may want give an idea how to do this
short the top two tap points on the right side not everyone is a knows about electrical stuff
I would recommend a copper wire for this two to work
Zenns said:
You may want give an idea how to do this
short the top two tap points on the right side not everyone is a knows about electrical stuff
I would recommend a copper wire for this two to work
Click to expand...
Click to collapse
Yes, addon advises are welcome to make it easy, but in the first place it is not for noob !
Noob users can get the replacement, instead wondering in unknown plane.
That is why @DooMLoRD have not given files, and only hinted how to .
Not working.
Sahara failSahara fail everytime.
shekhawat2 said:
Sahara failSahara fail everytime.
Click to expand...
Click to collapse
Just recently joint and want to try the hard process, Please call CC and get the replacement.
quakze said:
Just recently joint and want to try the hard process, Please call CC and get the replacement.
Click to expand...
Click to collapse
I am trying this process from last 4 days from here: http://forum.xda-developers.com/yureka/help/question-qualcomm-download-mode-k-t3068040 but getting the same error every time. :crying:
I have called CC, ill get replacement after few days, till then i want to try with it bricked, so that i can unbrick it myself next time as it was my 2nd time i hardbricked it. If you can, please help me.
shekhawat2 said:
I am try this process from last 4 days from here: http://forum.xda-developers.com/yureka/help/question-qualcomm-download-mode-k-t3068040 but getting the same error every time. :crying:
I have called CC, ill get replacement after few days, till then i want to try with it bricked, so that i can unbrick it myself next time as it was my 2nd time i hardbricked it. If you can, please help me.
Click to expand...
Click to collapse
I am busy with porting tonight, will work with you tomorrow.
BTW, send a private massage about ur contact details, so that we can have a chat while debricking.
@quakze Just one question Yureka has MSM 8939 and these files are for MSM 8936. So this means that both these means snapdragon 610 and 615 share same firehose files.
quakze said:
I am busy with porting tonight, will work with you tomorrow.
BTW, send a private massage about ur contact details, so that we can have a chat while debricking.
Click to expand...
Click to collapse
This is the error i am getting:
Sahara Version:2
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(String sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
Need help. I juat only need qfil thats all i have everything except that qfil please gv me a link.
sahara error
Sahara error.
This is the error i am getting:
Sahara Version:2
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(S tring sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownload ArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
ud3240 said:
Sahara error.
This is the error i am getting:
Sahara Version:2
Start Sending Programmer
Download Fail:System.Exception: Unable to download Flash Programmer using Sahara Protocol
at QC.QMSLPhone.Phone.QPHONEMS_SaharaArmPrgDownload(S tring sFileName)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownload ArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailSahara Fail
Finish Download
Click to expand...
Click to collapse
Don't skip this step !
Boot YUREKA to Qualcomm HS-USB QDLoader 9008 mode
Note: This is a forced Download mode which is different from normal mode, so this is a must step !
Step 1] Power off the device/remove the battery and the re-insert after few seconds.
Step 2] Open the back cover, unscrew all the screws for the inner cover. Pry open the inner cover to expose the 6 tap points next to the headset plug.
Step 3] With the battery connected, short the top two tap points on the right side, This is illustrated in the attached image.
Step 4] With the two tap points shorted, plugin the USB cable. The device will enter (9008) QDL mode. If the Qualcomm driver is installed correctly, the device will show up as a serial device.
quakze said:
Don't skip this step !
Boot YUREKA to Qualcomm HS-USB QDLoader 9008 mode
Note: This is a forced Download mode which is different from normal mode, so this is a must step !
Step 1] Power off the device/remove the battery and the re-insert after few seconds.
Step 2] Open the back cover, unscrew all the screws for the inner cover. Pry open the inner cover to expose the 6 tap points next to the headset plug.
Step 3] With the battery connected, short the top two tap points on the right side, This is illustrated in the attached image.
Step 4] With the two tap points shorted, plugin the USB cable. The device will enter (9008) QDL mode. If the Qualcomm driver is installed correctly, the device will show up as a serial device.
Click to expand...
Click to collapse
Bro i done all the steps including that shorting 2 Points. As i said my YU was detected as qual 9008 But final reaults is fail. Sahara error
ud3240 said:
As i said my YU was detected as qual 9008 But final reaults is fail. Sahara error
Click to expand...
Click to collapse
It will be detected as qual 9008, without shorting the two points also !
How??
quakze said:
It will be detected as qual 9008, without shorting the two points also !
Click to expand...
Click to collapse
Oh Really?? How?? Tell me procedure I will definitely try. Help me and have you unbrick your phone using this method? Help
Thank you for this guide but I'm unsure if i go throgh with this or not because theres A Yu sticker on one of the screws and i believe they will not consider the warranty if i take it out.
I hardbricked the phone today while updating from CM11 to CM12 via flash tool fastboot windows method. Now nothing happens. The led light doesnt light up when charging,no screen shows and nothing is detected on pc.
Still waiting for the callback from Yu. Lets see
zeeshanonlyme said:
Thank you for this guide but I'm unsure if i go throgh with this or not because theres A Yu sticker on one of the screws and i believe they will not consider the warranty if i take it out.
I hardbricked the phone today while updating from CM11 to CM12 via flash tool fastboot windows method. Now nothing happens. The led light doesnt light up when charging,no screen shows and nothing is detected on pc.
Still waiting for the callback from Yu. Lets see
Click to expand...
Click to collapse
Take a sharp knife or compass remove the whole sticker without damaging it.
And its a home pickup, so no technician will be there to check, but carrier guy !
Try this in the mean time, UR phone is getting replaced by YU.
quakze said:
Take a sharp knife or compass remove the whole sticker without damaging it.
And its a home pickup, so no technician will be there to check, but carrier guy !
Try this in the mean time, UR phone is getting replaced by YU.
Click to expand...
Click to collapse
Ya but say while taking out the sticker i damaged it, will my warranty be void?
And how long did it take for yours to get replaced?
zeeshanonlyme said:
Ya but say while taking out the sticker i damaged it, will my warranty be void?
And how long did it take for yours to get replaced?
Click to expand...
Click to collapse
No technician will come to check the phone while replacing at UR door step, so be cool and go ahead and try.
If U get the waybill no. in first three days, it will take total 10 - 12 days !
What is the starting situation?
You bricked your phone. It can't be started anymore. No charging, no recovery, no fastboot. Your phone is not recognized by your computer.
What to do now?
1. Drain the battery!
Therefore you just have to be patient. Press the power button every now and then. It takes approximately 2 days until the battery is drained.
How do you know if your battery is drained?
When connecting to a charging station or a computer the led-light will pop up red and turn off after a few seconds again.
2. Download the rom for your device!
HTML:
http://androidmtk.com/download-gionee-stock-rom-models
HTML:
http://www.android.gs/download-gionee-stock-rom/
The drivers and the flash tool you will need are also contained in the download.
3. Install the driver.
Your phone should be disconnected while you are installing them. When you connect your phone now it should be recognized under COM port as 'Qualcomm HS-USB QDLoader'.
4. Start the tool and set the settings like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
On almost every website it is stated that you should set "Platform" to "8x26". Do not do it! ( This was the cause my phone bricked)
"Platform" hast to be set to "8974" for our phone.
5. Click on download and wait until it is finished.
Enjoy your unbricked Gionee!
FAQ:
Q) GNQC download doesn't work. It gives the error "application failed to start".
A) Install VC++ 2005 redistributeble SP1 ATL security upgrade.
Q) I receive an "incorrect parameter error".
A) You are using a Chinese flash tool so make sure your copy of windows supports Chinese. Change local settings in the control panel.
Q) I receive an "in gnqc bp_image file doesnt exist" error.
A) Remove Chinese characters from the name of the image folder.
Q) My phone is not detected.
A) Let it sit and drain the battery in 1-2 days. Now plug it in via usb cable.
The biggest problem:
Q) My phone is detected as usb hid device instead of com port.
A) There are problems with different versions of Windows.
For me, this problem occured with Windows 8 64-bit.
It is recommended to follow the procedure on a computer with Windows XP 32-bit. Windows 7 32-bit might work also.
Alternatively:
Use a virtual machine. (I used Virtual Box by Oracle.)
1. Create a virtual image of windows xp 32bit in the virtual machine.
2. Install windows xp 32bit on it. (You need a windows xp installation ISO or CD)
3. Put the downloaded rom, flash tool and drivers into the virtual machine. (e.g. with an usb flash drive)
4. Install the drivers while your phone is disconnected. Now connect your phone to the virtual machine.
Now your phone should be recognized. Follow the rest of the procedure.
There are some threads on xda which try to help with bricked E7 devices. I just wanted to put all together and add some information. So make sure you check the credits!
Credits:
dhirajranger
HTML:
http://forum.xda-developers.com/showthread.php?t=2735079
StarLord21
HTML:
http://forum.xda-developers.com/elife-e7/general/unbricking-gionee-elife-e7-total-hard-t3186697
psghari
HTML:
http://forum.xda-developers.com/elife-e7/help/hardbricked-e7-fix-t3136602
[/QUOTE]The biggest problem:
Q) My phone is detected as usb hid device instead of com port.[/QUOTE]
My phone after drain the battery don't detected de device and don't light any red led. Nothing. Please can you help me? I am very disgust.
Thanks for your attention and hope your answer ASAP.
thesmartphonero said:
My phone after drain the battery don't detected de device and don't light any red led. Nothing. Please can you help me? I am very disgust.
Thanks for your attention and hope your answer ASAP.
Click to expand...
Click to collapse
First of all open your device manager. Then connect your phone. Check if any device was added (like unknown USB-device or something). That is the case if battery is not drained.
USB Input Device IN HID Menu
My phone is detected as USB Input Device in the HID Section
whats next?
Always shows this error..
Please help me out..
shivam2702 said:
My phone is detected as USB Input Device in the HID Section
whats next?
Click to expand...
Click to collapse
The biggest problem:
Q) My phone is detected as usb hid device instead of com port.
A) There are problems with different versions of Windows.
For me, this problem occured with Windows 8 64-bit.
It is recommended to follow the procedure on a computer with Windows XP 32-bit. Windows 7 32-bit might work also.
Alternatively:
Use a virtual machine. (I used Virtual Box by Oracle.)
1. Create a virtual image of windows xp 32bit in the virtual machine.
2. Install windows xp 32bit on it. (You need a windows xp installation ISO or CD)
3. Put the downloaded rom, flash tool and drivers into the virtual machine. (e.g. with an usb flash drive)
4. Install the drivers while your phone is disconnected. Now connect your phone to the virtual machine.
Now your phone should be recognized. Follow the rest of the procedure.
shivam2702 said:
Always shows this error..
Please help me out..
Click to expand...
Click to collapse
Make sure you have the right firmware.
4ndaKava said:
The biggest problem:
Q) My phone is detected as usb hid device instead of com port.
A) There are problems with different versions of Windows.
For me, this problem occured with Windows 8 64-bit.
It is recommended to follow the procedure on a computer with Windows XP 32-bit. Windows 7 32-bit might work also.
Alternatively:
Use a virtual machine. (I used Virtual Box by Oracle.)
1. Create a virtual image of windows xp 32bit in the virtual machine.
2. Install windows xp 32bit on it. (You need a windows xp installation ISO or CD)
3. Put the downloaded rom, flash tool and drivers into the virtual machine. (e.g. with an usb flash drive)
4. Install the drivers while your phone is disconnected. Now connect your phone to the virtual machine.
Now your phone should be recognized. Follow the rest of the procedure.
Make sure you have the right firmware.
Click to expand...
Click to collapse
Yes i'm having the correct firmware.... Please help
shivam2702 said:
Yes i'm having the correct firmware.... Please help
Click to expand...
Click to collapse
I think I have found your problem. Uncheck "Chenck Phone" and try again.
Otherwise just try to download the correct firmware again and try again.
Now Its showing a different Error....
It Shows this error after 1% in the Checking of GNQC files..
Can you please zip you GNQC folder and mail to me please.
I have also checked after unchecking the chunk phone but the result is same ...
1652.48 MB is shown at my section and your's showing 1652.50 MB...
Is it the issue?
Firmware Check
4ndaKava said:
I think I have found your problem. Uncheck "Chenck Phone" and try again.
Otherwise just try to download the correct firmware again and try again.
Click to expand...
Click to collapse
Are are using the "Gionee_E7_32G_0301_T8143.ZIP" ?
2,630,999 KB or 2,694,142,825 bytes or 2.50 GB....
is it the same?
And the link that you provided is having the V 4.2.2...
shivam2702 said:
Are are using the "Gionee_E7_32G_0301_T8143.ZIP" ?
2,630,999 KB or 2,694,142,825 bytes or 2.50 GB....
is it the same?
And the link that you provided is having the V 4.2.2...
Click to expand...
Click to collapse
http://www.android.gs/download-gionee-stock-rom/
You might also try this page for a rom.
Is it still recognized as hid?
If so, you should make it recognize as qualcomm 9008 or 9006 before trying..
shivam2702 said:
It Shows this error after 1% in the Checking of GNQC files..
Click to expand...
Click to collapse
I had the same problem, I solved in this way:
Open the downloader
Connect the phone
Wait until it's recognised
Try to flash
If it stops, unplug and then plug the phone again keeping the downloader opened.
I know it could seem stupid but in windows the most of the things works in this way...
:crying: Not Working for me
:crying:
Not Working for me
I restored but now no network please help
shivam2702 said:
It Shows this error after 1% in the Checking of GNQC files..
Can you please zip you GNQC folder and mail to me please.
I have also checked after unchecking the chunk phone but the result is same ...
1652.48 MB is shown at my section and your's showing 1652.50 MB...
Is it the issue?
Click to expand...
Click to collapse
I am also getting same error...
any solution...?
Awesome it made my Gionee unbricked
My device is soft bricked but the volume up key is broken so will this method work ?
and also that my device is not recognised
vedant.sharma68 said:
My device is soft bricked but the volume up key is broken so will this method work ?
and also that my device is not recognised
Click to expand...
Click to collapse
My xp 32 bits doesn't recognize the phone, it apperars like USB not Qualcomm... any idea?
ALCTEL HS Usb QDloder 9008 Driver Needed
All time i connect device to pc my pc detect hid/usb divice ...than 21/1/2016 my device connected pc and restart my pc. After restart i saw one iobit driver booster app wich notify me i have 3 new drive update one is my nvdia display one is my internet adapter ..but last one is unknown device detected ...than i click update now phone atomatic connect port ALCATEL HS Usb QDloder 9008 (port20)..now i open flash tool select firmware and select 8974 instead of 8x26 ..start download withing 5 minutes my phone downloaded 100% successfull now after 2 minutes i remove phone to pc connect charger red light start continue and 10 minutes later i pressed power button 15 second and my phone start like new unroot ..i al to happy that night ..thanks to all who give me right direction..thanks all ..sorry for bad English..
my phone dead
Hi friend,
My phone dead while updating on (GN_Qcom_Download_Tools_V2.1.0.1). Now cant connect Phone with PC even i installed all drivers for gionee elife e7 32GB. now in DEVICE MANAGER showing UNKNOWN DEVICE. kindly brothers someone guide me how to install again firmware.
---------- Post added at 08:18 AM ---------- Previous post was at 08:00 AM ----------
brother i have same problem with my gionee elife e7 32gb and i try same firmware Gionee_E7_32G_0301_T8180_(by_xdafirmware.com). ON GN_Qcom_Download_Tools_V2.1.0.1.
Kindly help me bro, my whatsapp 00971503294484.
shivam2702 said:
It Shows this error after 1% in the Checking of GNQC files..
Can you please zip you GNQC folder and mail to me please.
I have also checked after unchecking the chunk phone but the result is same ...
1652.48 MB is shown at my section and your's showing 1652.50 MB...
Is it the issue?
Click to expand...
Click to collapse
Link to the latest readback extractor thread
It is applying for mtk6260A watch phones as GT08, DZ09, GV08, T7, Iradish Y6, Q8, F8 and all variations
In short - if you intend to install in your smartwatch new firmwares, mods etc, before to initiate any flashing with the Flash Tool app (pushing that goddamn < Download > button) think twice, 'bove all better DO a backup for the original firmware, why so? because it's containing all original drivers hence you'll be able to recover 100% your watch in case of bricking.
How to:
First you have need of a full dump of your ROM. Assuming that you already got a Flash Tool 5.1308 and drivers, and you were at the point of flashing something (already chose the download agent and scatter file)
for instance let's say you have a DZ09 smartwatch:
1 - press < Readback > in upper menu and so < Add > in the middle menu
2 - click twice on the item appears in the main window, set name as ROM_DZ choose in browser the path and save
3 - set as Physical start address 0x00000000 and as Length 0x01000000 then ok
4 - press < Readback > in the middle menu wait 2 seconds and connect through USB your watch
5 - wait until the upload is complete (big green ring)
Now second stage:
1 - download the app I've built attached here (Readback Extractor mtk6260A 1.0.rar) and unzip it
2 - create a folder where you intend to keep in safe the original firmware and name it for instance DZ09-Orig
3 - do a copy of Readback Extractor mtk6260A 1.0.exe and place it inside the DZ09-Orig folder then click twice on it
4 - press <Load Readback file> and browse after the ROM_DZ file created before with the Flash Tool then open
5 - Wait about two minutes while the app will check bit by bit the integrity of your file
6 - If everything went ok and your file is healthy app will show " health 100% " so you can proceed to next step
7 - Press <Rebuild Firmware> and wait about 5 to 10 minutes (it has a progress counter there)
8 - When will appear the message " - ALL DONE!!!" close app and go back in the DZ09-Orig folder, now you'll find there 5 new files which are the original firmware kit ready to be flashed back in your phone anytime you want
AFTERWARDS READ ME story - Anywhere you search, there is no one to tell you explicitly how to extract from your mtk smartwatch the firmware kit
All says a halfmouth: Do a full < Readback > in Flash Tool, you'll do it being confident that from now on you say goodbye to any risk because you have A BACKUP hence you start flashing new firmwares. And the Big Brick is coming , you smile and get back to your < Readback > backup discovering that, sadly, you have a binary bulk at first sight good for nothing. It cannot be so useless, isn't it? after all it contains full dump of your ROM! I was in exactly the same situation, so 'cause I didn't find any answer I've started reverse engineering . . . and it worked, first I did it manually for guys being in the same situation, 've noticed that is a common issue so I had to choose how to help, simpler but dangerous (for you) way, to create a tutorial <how to> or the hard way (hard for me), to develop an app which will do all "cooking" automatically and I choose the second because in manually way there is a quite big "chance" to mess up with your primary bootloader which could get to a real tragedy - no modem - brickest brick you saw in your entire life
thanks
thank you very much!!! I was searching how to backup my firmware and I found this forum!! Thank you! Thank you! Thank you!
make video pls!!
hello, please make video how you backup dz09 smartwatch original firmware!! PLEASE!! Thank You!!!
flagerchika said:
thank you very much!!! I was searching how to backup my firmware and I found this forum!! Thank you! Thank you! Thank you!
Click to expand...
Click to collapse
Very wise decision to backUP your firmware! Let me know how things goes
gugesha said:
hello, please make video how you backup dz09 smartwatch original firmware!! PLEASE!! Thank You!!!
Click to expand...
Click to collapse
Unfortunately, my time is quite limited,follow the steps in tutorial, if anything is unclear ask here
Thank you Golem_ for this nice tut.
Unfortunately with my GT08 the FlashTool doesn't seem to start the Read Back process. I see the watch in device manager (COM4), installed the MTK VCOM drivers. I can even access the AT interface of the watch (when the watch is powered on).
The steps i tried to perform are..
1) power off the watch
2) start flash tool, start the Read Back
3) connect the watch via usb --> COM4 appears in device manager
4) flash tool detects watch on COM4 port
5) nothing further happens - Read Back won't start (not even after 1 hour of waiting)..
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I've tried with FlashTool v5.1308.00.00 and even the latest v5.1524.00 from spflashtool.com. Same result..
any clues?
dominic1134 said:
Thank you Golem_ for this nice tut.
Unfortunately with my GT08 the FlashTool doesn't seem to start the Read Back process. I see the watch in device manager (COM4), installed the MTK VCOM drivers. I can even access the AT interface of the watch (when the watch is powered on).
The steps i tried to perform are..
1) power off the watch
2) start flash tool, start the Read Back
3) connect the watch via usb --> COM4 appears in device manager
4) flash tool detects watch on COM4 port
5) nothing further happens - Read Back won't start (not even after 1 hour of waiting)..
I've tried with FlashTool v5.1308.00.00 and even the latest v5.1524.00 from spflashtool.com. Same result..
any clues?
Click to expand...
Click to collapse
you have to load a scatter file from a compatible firmware (just for initialization, not for flashing)
Golem_ said:
you have to load a scatter file from a compatible firmware (just for initialization, not for flashing)
Click to expand...
Click to collapse
yep, loaded the scatter from the firmware over here http://www.needrom.com/download/gt08-mt6260a-2/
dominic1134 said:
yep, loaded the scatter from the firmware over here http://www.needrom.com/download/gt08-mt6260a-2/
Click to expand...
Click to collapse
still not working? that's weird!
Golem_ said:
still not working? that's weird!
Click to expand...
Click to collapse
yep it is kinda weird...
dominic1134 said:
yep it is kinda weird...
Click to expand...
Click to collapse
Try a RAM test (be aware, only RAM!), who knows, maybe your watch is on 64Mb
Golem_ said:
Try a RAM test (be aware, only RAM!), who knows, maybe your watch is on 64Mb
Click to expand...
Click to collapse
RAM test doesn't start either...
In the developer menu with #993646633# it says [MEM SIZE] 1299684 btw.
I can also set the UART settings, BAUD, etc.
dominic1134 said:
RAM test doesn't start either...
In the developer menu with #993646633# it says [MEM SIZE] 1299684 btw.
I can also set the UART settings, BAUD, etc.
Click to expand...
Click to collapse
Flash tool has to be set on Options / USB Download/Readback and BackUP and Restore on no action
Please does anyone have the stock ROM file for apro q18 smart watch
Unable to carry read back or memory test
Hi Golem,
Firstly please accept my appreciation for your indepth analysis and details that you have been sharing on forum..
I have been scratching since yesterday evening to do readback and install drivers , but am unable to do it succesfully. It I add drivers from device manager and then run the run back I get following error:
FLASHTOOL ERROR : S_BROM_CMD_STARTCMD_FAIL (2005)
[BROM] Can not pass bootrom start commabd! POssibly target power up too earlu.
[HINT]
Can you please help? I am scratching and trying various things - but I guess am missing something on the installation side... Tried installing with different versions including WIN XP Service pack2,3 etc. but no success... Same error when I run Memory test to check if indeed the drivers have installed..
vir25 said:
Hi Golem,
Firstly please accept my appreciation for your indepth analysis and details that you have been sharing on forum..
I have been scratching since yesterday evening to do readback and install drivers , but am unable to do it succesfully. It I add drivers from device manager and then run the run back I get following error:
FLASHTOOL ERROR : S_BROM_CMD_STARTCMD_FAIL (2005)
[BROM] Can not pass bootrom start commabd! POssibly target power up too earlu.
[HINT]
Can you please help? I am scratching and trying various things - but I guess am missing something on the installation side... Tried installing with different versions including WIN XP Service pack2,3 etc. but no success... Same error when I run Memory test to check if indeed the drivers have installed..
Click to expand...
Click to collapse
Most common mistakes are not turning off the watch before connect to usb and connecting at usb before to start a command in flash tool. If these are not the issue then go in options/backup and restore and set on no action
Use your money wisely, DO NOT WASTE IT buying from GEARBEST
Issue not resolved yet...
QUOTE=Golem_;67280709]Most common mistakes are not turning off the watch before connect to usb and connecting at usb before to start a command in flash tool. If these are not the issue then go in options/backup and restore and set on no action
Use your money wisely, DO NOT WASTE IT buying from GEARBEST[/QUOTE]
Thanks buddy.
Removed battery, tried again - changed USB cord - tried in different port - but still gives same error - Also changed setting to no action in Option-> Backup and Restore.... Few observations - on attaching cable the device manager shows device as Mediatek USB Port (Other drivers present being MTK USB PORT, MTK USB Modem Port, MTK USB debug port, USB Modem Driver. All with a COM port assigned. Then it tries to connect and gives this error.
When tried using download with scatter files and Download agent it again gives error - META ERROR - ERROR in BOOTROM COMMUNICATION.
Can you please help - I am thinking some issue with set-up or drivers... Your suggestion? Thanks!
---------- Post added at 09:54 AM ---------- Previous post was at 09:34 AM ----------
vir25 said:
QUOTE=Golem_;67280709]Most common mistakes are not turning off the watch before connect to usb and connecting at usb before to start a command in flash tool. If these are not the issue then go in options/backup and restore and set on no action
Use your money wisely, DO NOT WASTE IT buying from GEARBEST
Click to expand...
Click to collapse
Thanks buddy.
Removed battery, tried again - changed USB cord - tried in different port - but still gives same error - Also changed setting to no action in Option-> Backup and Restore.... Few observations - on attaching cable the device manager shows device as Mediatek USB Port (Other drivers present being MTK USB PORT, MTK USB Modem Port, MTK USB debug port, USB Modem Driver. All with a COM port assigned. Then it tries to connect and gives this error.
When tried using download with scatter files and Download agent it again gives error - META ERROR - ERROR in BOOTROM COMMUNICATION.
Can you please help - I am thinking some issue with set-up or drivers... Your suggestion? Thanks!
[/QUOTE]
Dear Golem - My Skype id is: viral.gosalia, can we skype chat?
vir25 said:
QUOTE=Golem_;67280709]Most common mistakes are not turning off the watch before connect to usb and connecting at usb before to start a command in flash tool. If these are not the issue then go in options/backup and restore and set on no action
Use your money wisely, DO NOT WASTE IT buying from GEARBEST
Click to expand...
Click to collapse
Thanks buddy.
Removed battery, tried again - changed USB cord - tried in different port - but still gives same error - Also changed setting to no action in Option-> Backup and Restore.... Few observations - on attaching cable the device manager shows device as Mediatek USB Port (Other drivers present being MTK USB PORT, MTK USB Modem Port, MTK USB debug port, USB Modem Driver. All with a COM port assigned. Then it tries to connect and gives this error.
When tried using download with scatter files and Download agent it again gives error - META ERROR - ERROR in BOOTROM COMMUNICATION.
Can you please help - I am thinking some issue with set-up or drivers... Your suggestion? Thanks!
---------- Post added at 09:54 AM ---------- Previous post was at 09:34 AM ----------
Thanks buddy.
Removed battery, tried again - changed USB cord - tried in different port - but still gives same error - Also changed setting to no action in Option-> Backup and Restore.... Few observations - on attaching cable the device manager shows device as Mediatek USB Port (Other drivers present being MTK USB PORT, MTK USB Modem Port, MTK USB debug port, USB Modem Driver. All with a COM port assigned. Then it tries to connect and gives this error.
When tried using download with scatter files and Download agent it again gives error - META ERROR - ERROR in BOOTROM COMMUNICATION.
Can you please help - I am thinking some issue with set-up or drivers... Your suggestion? Thanks!
[/QUOTE]
Dear Golem - My Skype id is: can we skype chat?[/QUOTE]
sent you a message in skype
Use your money wisely, DO NOT WASTE IT buying from GEARBEST
flashtool error
i get the same erro annyone pls help
looks like same problem as Dominic, flashtool just sits waiting. Any solutions
Any solutions not already tried, multiple ports, computers, baud rates cables mem test etc.
dominic1134 said:
RAM test doesn't start either...
In the developer menu with #993646633# it says [MEM SIZE] 1299684 btw.
I can also set the UART settings, BAUD, etc.
Click to expand...
Click to collapse
Hello people ...
Here it's official ... since two days ago the official update for our LG MAGNA for version 6.0 of Android.
We had to wait a long time .. but ... essentially it's there.
Contrary to what I expected ... it is very well done ... I mean the LG interface with this version of MM. The least I can say is that it is purified ... LG overlay is married to that of pure Android ... finished the coarseness of the characters and the colors too dull (for my taste) of LG interface .
Frankly I like it a lot.
It remains to wait for an opportunity to ... ROOT and a custom recovery (why not ... I'm always up for a custom ROM).
To come to this update ... it is only available for the CIS countries yet .. but .KDZ is available for download .. and it is this version that I installed CIS.
So for those who have received the update OTA .. it can install ... for those in a hurry (like me) .. or have ROOT their phone and install TWRP .. they can install this update via OTA ... so must follow this method.
I want to thank my friend Berong the XDA forum which was the precursor to try it and I was a big help to do it.
I put the method to the next post.
So ... to install this version of Marshmallow ... we will need the following.
Euuuh .. you are solely responsible for anything that may happen to your phone by following this method ... neither me nor xda forums are responsible .. blah .. you are warned .
So .. we will need:
- The .KDZ (V20A for CIS) of course available here : http://lg-phone-firmware.com/index.php?id_mod=237
- The LG Flashtool 1.8.6.527 utility from here : https://www.sendspace.com/file/df0h5a
- The extraction utility KDZ from here : https://www.sendspace.com/file/cqq0kk
- The LG drivers here : https://www.sendspace.com/file/6jtwob
First stage :
1- Download and install the drivers for LG
2. Extract the .KDZ
The purpose of this operation is to extract the .KDZ to use it in the flash utility.
To do this ..
- Download and Install KDZ Extractor ..
- Launch the application and select the file .KDZ
- Check all files (3) ... and click Extract KDZ
- When finished, we will have 3 new files (.DLL + .DZ + LIB).
Of these three the only files .DZ and .DLL will be used later.
3- INSTALL LG Flashtool:
- Download LG FLASTOOL RAR
- Unzip the archive
- Install it.
- Copy and paste the MegaLock.dll file in the installation folder (default c:\LG ).
4- Change Port communication :
- Connect the phone to the USB
- Go to Device Manager
- Find "Ports (COM & LPT)", click on the tab on the left to expand it. You should see "LGE Mobile USB Serial Port (COM)".
- Double click on "LGE Mobile USB Serial Port (COM)"> Port Settings> Advanced> next to "COM Port Number" choose "COM41".
- Click on "OK" and then "OK" again.
Here .. now everything is ready .. move to flash the firmware.
Second step :
- Switch off the phone.
- Go DOWNLOAD mode : off phone ... press and hold volume UP plug the usb cable (you are in Download mode).
- Launch LG Flashtool
- Select the manual mode
- Click on "..." and choose the .DLL file (the one extracted earlier from the KDZ).
- Click on "Add" and the choose .DZ file (the one extracted earlier from the KDZ).
- Uncheck upgrade dl and check board dl (very important).
- OK
- In the new window .. just click on yellow arrow (Top left)
- The flash process starts and takes about 4-5 minutes.
- Once finished .. it should display PASS
- The phone will restart
That's it ... you just have to configure your phone and enjoy.
PS: it may be that first start you come across a kind thing: FACTORY RESET STATUS .. then just do (thanks for BERONG) :
1. Remove Battery
2. Power on
3. Do not touch the screen when you see MINI OS
4. Hold power button while MINI OS visible in screen
5. A menu will pop out... Find NORMAL BOOT (+POWER) .
6. Tap that while holding the power button (by clicking simultaneously on several occasions on NORMAL BOOT and the POWER).
Enjoy.
I forgot what site I read about MINI OS workaround anyways credit to them It was not me who originally got that idea... anyways ...
I will just provide some screenies ...
1.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2.
3.
4.
Thank you BERONG ... good job
I added step 4 on the port change.
I'll be flashing back to 5.0.1 again, I can't live without root
I'll be checking this thread from time to time... Hoping for some development like
1. ROOT
2. BOOTLOADER unlock
3. RECOVERY TWRP
I will try it tonight, thanks for the guide! I'm sure our russian friends will get us root and twrp, they are very enthusiastic
Works on H500f.
Tnks
Works fine for me, tanks
Root and install TWRP on LG MAGNA with MARSHMALLOW .... from here : http://forum.xda-developers.com/andr...magna-t3396704
Thanks
Sent from my LG-H502 using XDA-Developers mobile app
I have just recently installed it. Had no problems whatsoever
Why do my phone wont display its data indicator... It is connected though, I just wonder why help meeeee... Is it connected with my region...? Im flasing/using/ same file with same method.
Sent from my LG-H502 using XDA-Developers mobile app
Hello people.
For those who have updated their MAGNA to android 6.0 official ... and want to use the SD card as internal storage .. and do not find this option when formatting the SD card here .. taking method LG forum in SPIRIT on XDA. This method has been tested by me and successfully.
- Backup your data on SD because all data will be lost after formatting and encryption SD card (you can copy the latest since the backup on PC.
- Enable USB debugging mode in developer settings.
- Open ADB SHELL command (from the ADB folder .. shift + right mouse button ... OPEN A WINDOW COMMAND)
- List avaliable disks to get disk ID. It can be done with following command:
sm list-disks
You will get your SD Card ID (ex.: disk:179,64, which will be used in next step.
In our example the id is 179.64 for you ... you-remember number that is yours.
After that .. we have the choice of using any SD card or internal memory or half If you want to use only part of SD as Internal Storage and rest as standard Removable Disk, for example 50:50, ...
So it recapitulates the command line:
For all of the SD card :
adb shell
sm list-disks
sm partition disk:179,64 private
For 50/50 of the SD card:
adb shell
sm list-disks
sm partition disk:179,64 mixed 50
Remember that 179.64 is an example .. ID with you to put yours
Here is a screenshot of the command 50/50
Good luck.
Failed PreviousLoad()
After selected the yellow arrow into LG flash tool a receive the error message that says "Failed PreviousLoad()"
ikki82 said:
After selected the yellow arrow into LG flash tool a receive the error message that says "Failed PreviousLoad()"
Click to expand...
Click to collapse
have you installed all necessary driver?
Sent from my LG-H502 using XDA-Developers mobile app
yes I have installed the correct driver
yes I have installed the correct driver (LGMobileDriver_WHQL_Ver_4.0.4), tested with 2 different laptops and different operative system, and I receive the same error. also using different usb ports and different usb cables.
can you provide some screenshots?
Sent from my LG-H502 using XDA-Developers mobile app
I dont have the option to upload screenshots
I dont have the option to upload screenshots
@ikki82.. I think you selected the wrong dll...
There is a v20a for kazakh...
Sent from my LG-H502 using XDA-Developers mobile app
This is a Method to update Firmware of Sony MW1 , Sony SBH52 and SBH54. I extract the firmware from the headset apk.
BIG UPDATE
Instructions for Sony MW1:
1. Download the Attachment "Sony MW1 Firmware Tool"
2. Reset your Device via Settings/Systeminfo/Reset
3. Power off your Sony MW1, press "back-button" and connect in the same moment your device to the usb port of your computer.
Now you should see this screen:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. Now open the program "zadig.exe" in the Attachment and press Options/List all Devices.
4.1 Now you choose your device which is connected in DFU-Mode and which should be named "LANCE", Choose "WinUSB (v6.1.7600.16385)" and" press "Replace Driver"
5. Now open "Firmware-TOOL.bat" Batch File, choose your Firmware and wait until the Flash Process finished.
if Flash Process was successful you get a green screen(If i didnt make something wrong error interpretation).
PS: Dont get scared if you get a red screen. This only means that you didnt follow all steps in this Instruction.
6. Remove USB-Cable and Press Power button.
7. Reset your Device again and have fun with your "stable" Firmware.
Instructions for Sony SBH52:
1. Download the Attachment "Sony SBH52 Firmware Tool"
2. Reset your Device via Settings/Reset
3. Power off your Sony SBH52, press "back-button" and connect in the same moment your device to the usb port of your computer.
Now you should see this screen:
4. Now open the program "zadig.exe" in the Attachment and press Options/List all Devices.
4.1 Now you choose your device which is connected in DFU-Mode and which should be named "SBH52", Choose "WinUSB (v6.1.7600.16385)" and" press "(Re)install Driver"
5. Now open "Firmware-TOOL.bat" Batch File, choose your Firmware and wait until the Flash Process finished.
if Flash Process was successful you get a green screen.
PS: Dont get scared if you get a red screen. This only means that you didnt follow all steps in this Instruction.
6. Remove USB-Cable and Press Power button.
7. Reset your Device again and have fun with your "stable" Firmware.
Instructions for Sony SBH54:
1. Download the Attachment "Sony SBH54 Firmware Tool"
2. Reset Your Device
3. Power off your device, then hold down call button and at the same time connect with the usb to pc [Thanks to pelopis]
4-7. Same like SBH52 Instructions
Warning: I take no responsibility for bricked devices or angry Sony staff.
Changelog
Latest Updates:
V.1.0 for Sony SBH 54 Firmware Tool
-added 7 different Firmware Files, which are extracted from the offical Sony App
-Option for Custom Firmware update
-Backup and Restore your Firmware
V.1.0 for Sony SBH 52 Firmware Tool
- added Sony SBH 52 Firmware Update and Downgrade Tool with 2 Firmwares: 2.3.A.0.9 and 2.4.A.0.2 [Tool Tested by myself and Tool is stable]
V.2.1 for Sony MW1 Firmware Tool
- added Option for Custom Firmware Update and Restore of backup Firmware on Sony MW1 tool with marked as BETA
----------------------------------------------------------------------------------------------------------------------------
V.2.0 for Sony MW1 Firmware Tool
- update zadig.exe
- new Batch File with MENU
- Included many other firmware updates for example: firmware 0.1.C.0.3, 0.1.E.1.4 and 0.1.E.1.6
- Add Backup feature which creates a backup of your current firmware (PS: you can send me your firmware files if they er not included in the batch File)
- Add Font.bin File to the Download files at the bottom (Font.bin fixes issues with special mp3 tags for example with Chinese or Japanese characters)
- minor bug fixes
V.1.1 for Sony MW1 Firmware Tool
- update zadig.exe
- update dfu-util.exe ( should fix error with multiple DFU devices)
V.1.0 for Sony MW1 Firmware Tool
-initial version
Troubleshooting:
If you followed all steps but dfutil cant find any dfu device then try another usb Port which is not Usb 3.0.
Please provide me older Firmware Files or older Sony MW1 and Sony SBH 52/54 Applications, for expanding the choice of Firmware.
Don´t forget to press Thanks and spread this Solution on other forums with referring on this Thread.
Feedback
Any Feedback or Thanks if you downloaded and tested this method??
USB Device Does Not Show Up
burak5 said:
Any Feedback or Thanks if you downloaded and tested this method??
Click to expand...
Click to collapse
So, when I get my MW1 into the file transfer mode. The same display as you sent. I do not get any recognition of the OS that a USB device is connected.
Mac OS 10.9.2, Windows 8.1 64bit, Windows 7 64bit.
The device is not detected in zadig. Am I missing a step? The device does not show up in device manager, or System Profiler (OSX).
Am I missing a step?
1. It´s not file transfer mode. It´s Firmware update mode (you need to press back button while connecting your device)
2. It should show up (I have a win 7 64bit)
I think you maybe missed the back button or your computer cant download the drivers (?)...
My USB Cable was shot.
So zadig.exe has "Install Driver" not "Replace". DFU-Util is saying that I have more than one device in DFU Mode. Is there a way to modify the install.bat to specify a specific device?
zadig.exe detects 5 devices on my Macbook Pro running Windows.
burak5 said:
1. It´s not file transfer mode. It´s Firmware update mode (you need to press back button while connecting your device)
2. It should show up (I have a win 7 64bit)
I think you maybe missed the back button or your computer cant download the drivers (?)...
Click to expand...
Click to collapse
Opening DFU capable USB device... Cannot open device
Hi ,
I have tried to downgrade it by given steps, While opening install.bat it says "Opening DFU capable USB device... Cannot open device"
Please do the needful
---------- Post added at 06:05 PM ---------- Previous post was at 05:57 PM ----------
paisakya said:
Hi ,
I have tried to downgrade it by given steps, While opening install.bat it says "Opening DFU capable USB device... Cannot open device"
Please do the needful
Click to expand...
Click to collapse
Appreciate your help
VirginiaVn900 said:
My USB Cable was shot.
So zadig.exe has "Install Driver" not "Replace". DFU-Util is saying that I have more than one device in DFU Mode. Is there a way to modify the install.bat to specify a specific device?
zadig.exe detects 5 devices on my Macbook Pro running Windows.
Click to expand...
Click to collapse
I updated the dfu-util. Now this error shouldnt happen anymore.
Pls give Feedback
paisakya said:
Hi ,
I have tried to downgrade it by given steps, While opening install.bat it says "Opening DFU capable USB device... Cannot open device"
Please do the needful
---------- Post added at 06:05 PM ---------- Previous post was at 05:57 PM ----------
Appreciate your help
Click to expand...
Click to collapse
Then you missed the steps with zadig.exe.
I updated the instructions.
Please look on Step 4 and 4.1 with the picture.
Thanks!
Great job man!
I wrote several times to complain about sony for this update but I have never heard.
With the downgrade is risen!
Verified Safe
burak5 said:
I updated the dfu-util. Now this error shouldnt happen anymore.
Pls give Feedback
Then you missed the steps with zadig.exe.
I updated the instructions.
Please look on Step 4 and 4.1 with the picture.
Click to expand...
Click to collapse
Verified Working.
Now running 0.1.D.0.6
Thanks a million!
Thanks
Please use Thanks button for telling thank you
Thank you so much!! finally found a way to downgrade! you saved my mw1 from the trash can lol. can't believe sony just dropped the support entirely without fixing the firmware...
pressed "back button" and connected usb port but didn't display firmware download mode just charging icon. OS is win8.1 usb3.0. i'm sure the button i pressed is "back button" not volume back button. please help me. Thanks
joyqing said:
pressed "back button" and connected usb port but didn't display firmware download mode just charging icon. OS is win8.1 usb3.0. i'm sure the button i pressed is "back button" not volume back button. please help me. Thanks
Click to expand...
Click to collapse
1. If it didn't switch to firmware update mode you pressed the false button ( or the Usb 3.0 port create problems)
2. Usb 3.0 port is not supported by the dfu-util ( I tested myself), but Windows 8.1 is supported
>>> Switch to Usb 2.0 port and test all buttons, if the back button didn't work (but should work).
PS: Dont forget to give feedback, which thing created a problem
burak5 said:
1. If it didn't switch to firmware update mode you pressed the false button ( or the Usb 3.0 port create problems)
2. Usb 3.0 port is not supported by the dfu-util ( I tested myself), but Windows 8.1 is supported
>>> Switch to Usb 2.0 port and test all buttons, if the back button didn't work (but should work).
PS: Dont forget to give feedback, which thing created a problem
Click to expand...
Click to collapse
finally I got it. no problem with usb3.0+win8.1 64bit.
at first I pressed the wrong button.
Thanks man.:laugh:
I can confirm it is working, hope my MW1 is stable now...
Does anyone know what the benefits are of this FW instead of the latest?
Is there any way to increase the Max volume?
request pls
hi..G8 job...Just saw ur post and trying to revive the MW1...iam using ur steps right now...just don't know if the flashing is over.....any msg will come??
In meantime any recent update to this post..since i am seeing this post from 2014..
Thanks a lot in advance
How is your MW1 ? Please give some feedback!
joyqing said:
finally I got it. no problem with usb3.0+win8.1 64bit.
at first I pressed the wrong button.
Thanks man.:laugh:
Click to expand...
Click to collapse
TheTeek said:
I can confirm it is working, hope my MW1 is stable now...
Does anyone know what the benefits are of this FW instead of the latest?
Is there any way to increase the Max volume?
Click to expand...
Click to collapse
surchit said:
hi..G8 job...Just saw ur post and trying to revive the MW1...iam using ur steps right now...just don't know if the flashing is over.....any msg will come??
In meantime any recent update to this post..since i am seeing this post from 2014..
Thanks a lot in advance
Click to expand...
Click to collapse
Hello guys! How is your MW1 doing nowadays? I am about to buy two units for my brother and me, and would not want a fiasco.
Please, tell me, with this firmware version 0.1.D.0.6 the device is working perfectly? Do you recommend this headset?
For me this is the most complete and feature packed Bluetooth headset today, I am about to buy it.
Are all its features working in Android 5.1.1?
Please help me! Thank you!
---------- Post added at 12:18 PM ---------- Previous post was at 11:56 AM ----------
burak5 said:
Like the Title says, I found a Solution for downgrading your devices after one Day I got my Sony MW1 . I'm Using the, method of Flashing
Sony Smartwatch 2 optimized on the Sony MW1 which is using a similar (same?) Hardware. I extract the firmware from the headset apk.
Instructions:
1. Download the Attachment "Sony MW1 Downgrade 0.1.D.0.6"
2. Reset your Device via Settings/Systeminfo/Reset
3. Power off your Sony MW1, press "back-button" and connect in the same moment your device to the usb port of your computer.
Now you should see this screen:
4. Now open the program "one m.exe" in the Attachment and press Options/List all Devices.
4.1 Now you choose your device which is connected in DFU-Mode and which should be named "LANCE", Choose "WinUSB (v6.1.7600.16385)" and" press "Replace Driver"
5. Now open the "Install.bat" script and wait until the Flash Process finished.
6. Remove USB-Cable and Press Power button.
7. Reset your Device again and have fun with your "stable" Firmware.
Warning: I take no responsibility for bricked devices or angry Sony staff.
Changelog
V.1.1
- update zadig.exe
- update dfu-util.exe ( should fix error with multiple DFU devices)
V.1.0 by
-initial version
Please provide me older Firmware Files or older Sony MW1 Applications, for expanding the choice of Firmware.
Don´t forget to press Thanks and spread this Solution on other forums with referring on this Thread.
Click to expand...
Click to collapse
Hey, man! Thank you for this tutorial and update! Seems like this is the only one Would you tell me how is your MW1 doing? Is it working fine with Android 4 and 5?
Have you got any other older firmware? Like C version 0.1.C.0.3? Is this version 0.1.D.0.6 is working fine with all the features?
I would very much appreciate your comments on the device as I'm about to buy it!
Thank you!
yes my mw1 is working fine with android 4.1 and it should work fine with android 5 because bluetooth headset protocol ist standarized.
MW1 is now awesome!!!
After getting these bulk, with no instructions, I finally got it to pair with my Nexus 6. After pairing it did not play over the headset, just out of the N6 speakers. After a power cycle it started working. The sound sucked the big one. It was like hearing it over an answering machine from the 80's. So after a google search on firmware, I saw this thread.:victory:
It only took 3 minutes to downgrade and it sounds GREAT!!!!!:good:
I am on windows 10 with a USB 3.0 and let the Zadig update to 2.1.2.677. All the other files were fine.
The install.bat file only took about a minute to finish.
Many Thanks and Happy Holidays!!!!
I made a big update and included other firmware updates which you can test. I couldn't test al of it because i don't have a Sony MW1 any more (I tried to change the battery and broke it ) . It would be nice if you could test All firmware updates which I extract from the official Sony MW 1 Application and the new batch File Menu. I hope I don't get into trouble because of some angry Sony staff