Database Users

[Ref][Guide] Galaxy Note N7000 Factory Firmware Restore

This is just like any other guide that tells you how to restore your phone to factory...
Please Note All User Data Will Be Lost
Recommended Battery is Fully Charged..
Requirement:
Odin3 1.85 (Download links Attached)
Window Drivers [32bit] or [64bit]
MicroUSB data cable for phone
Firmware files for mobile phone
Phone Obviously....
GB Firmwares: (if password required its "samfirmware.com")
-N7000DXKK1; N7000DXKJ3; N7000OLBKJ6
-N7000JPKJ4; N7000XXKJ4; N7000OJPKJ3
-N7000JPKK2; N7000XXKK5; N7000OJPKK2
-N7000XXKJ4; N7000XXKJ4; N7000PLSKJ3
-N7000XXKJ1; N7000XXKJ1; N7000OXAKJ1
-N7000XXKJ4; N7000XXKJ4; N7000OXAKJ4
-N7000XXKJ4; N7000XXKJ4; N7000XEOKJ1
-N7000XXKJA; N7000XXKJ4; N7000OXXKJ8
-N7000XXKK9; N7000XXKK5; N7000OXAKK9
-N7000XXKKA; N7000XXKK5; N7000OXXKK5
-N7000ZSKK1; N7000XXKJ6; N7000OZSKK1
ICS Firmware (Official)
N7000XXLPY (Single File Load in PDA)
N7000ZSLPF Build: 15.05.2012
FIRMWARE NAME DECODE
Warning: Don't Do This For Fun... could make your phone a nice paper weight..... use only if NEEDED.... I'm not responsible for any mistakes.... The Risk is YOURS!!!
PIT Info:
Changing PIT file (repartitioning ROM) will not affect mobile phone's speed.
PIT files will repartition the mobile phone's ROM (Read-Only Memory). Changing (repartitioning the ROM area) will modify only the space trade between the /system and /dbdata.
What is CSC?
CSC = Country Sale Code
CSC code depends on the region where the phone was sold.
CSC contains the phone settings (internet, wap, mms...), specific applications which available in certain regions, and operator customizations.
CSC code could be changed by flashing a new firmware (including CSC file) on phone. That will change phone language and settings.
Use *#272*IMEI# code on phone to view the list of the available CSCs, or change CSC. (Changing CSC will erase the phone!)
Lets Get Started..
1. Install Samsung USB drivers (in most cases already installed)..
2. Enter Download mode by pressing Volume down, OK and power buttons at the same time. Phone will start in Download mode.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. Press Volume Up..
4. Connect phone to USB cable. (Windows will install if needed).
5. Run Odin Software
6.If repartition is needed, Press PIT button to select .pit file. (Choose The Correct one for your phone internal memory size 16 or 32 GB)
7. Flash Bootloader If Needed, Enable Phone Bootloader Update then press Bootloader button to select bootloader file (filename: KERNEL_... .md5). (Important: Changing / flashing wrong bootloader could damage the phone!)
8.Press PDA, then select PDA file (filename: CODE_... .md5).
9. Press PHONE, then select PHONE file (filename: MODEM_... .md5)
10.Press CSC, then select CSC file (filename: ...-CSC-... .md5).
11. Verify Odin software recognize phone. When the phone is recognized, ID:COM is highlighted in yellow Note: the number can vary(if not repeat steps 2.)
12.Press Start button to begin flashing procedure.
13. Wait a few minutes flashing procedure to complete, This Can Take Some Time.... Plz Be Patience.....
Once Completed PASS! will appear on the upper left corner, and it will be highlighted in green.
---------------------------------------------------------------------------------------------------
Note: if only one file is in firmware download load in into PDA Section leave the rest empty and off as default

hello cannot download one of your roms

brockyneo said:
hello cannot download one of your roms
Click to expand...
Click to collapse
sorry try again links fixed

antiguangenius said:
sorry try again links fixed
Click to expand...
Click to collapse
thank you why do you think this will work for our bricked devices
also are all the files like bootloader and kernel all with the rom download i really hope this works thank you

brockyneo said:
thank you why do you think this will work for our bricked devices
also are all the files like bootloader and kernel all with the rom download i really hope this works thank you
Click to expand...
Click to collapse
read whole post carefully....

Thanks a lot mate, I've finally recovered my phone

Last resort actions always...pit & bootloader flashing. does the ics update require these?

Avlrln said:
Last resort actions always...pit & bootloader flashing. does the ics update require these?
Click to expand...
Click to collapse
dude this guide is all about factory state... in other words GB

Thank You!!!

not work in my case do same as he mantion
brockyneo said:
thank you why do you think this will work for our bricked devices
also are all the files like bootloader and kernel all with the rom download i really hope this works thank you
Click to expand...
Click to collapse
not work in my case do same as he mantion

.pit file
.PIT file is used for full flashing method, this is only advisable and useful for reverting back to original firmware when previously installed unofficial ROM or to fix softbricked devices like unable to boot normally.

I hope not to be OT in this thread and sorry for my bad english.
I would like to ask a question about the recovery / download mode.
It is necessary that the device is turned off before using the specific combo? (vol. up/down + home + power)
Can I go into recovery mode even when the terminal is already on?
If not, why?
Thanks in advance

posalaquaglia said:
I hope not to be OT in this thread and sorry for my bad english.
I would like to ask a question about the recovery / download mode.
It is necessary that the device is turned off before using the specific combo? (vol. up/down + home + power)
Can I go into recovery mode even when the terminal is already on?
If not, why?
Thanks in advance
Click to expand...
Click to collapse
You need to switch off first, otherwise it will just bootloop rather starting in recovery.

posalaquaglia said:
I hope not to be OT in this thread and sorry for my bad english.
I would like to ask a question about the recovery / download mode.
It is necessary that the device is turned off before using the specific combo? (vol. up/down + home + power)
Can I go into recovery mode even when the terminal is already on?
If not, why?
Thanks in advance
Click to expand...
Click to collapse
Are you asking if you can go into Recovery or Download mode when your phone is on,ie,w/o switching it off?
Yes you can.For recovery mode press up volume+home+power(strangely enough any combo works.power+home+volume but keep them pressed till the phone reboots and you see the Samsung GT-N7000 logo then u can let go.
For Download mode press down volume+home+power(again in any combo)
Hope i answered your question

dr.ketan said:
You need to switch off first, otherwise it will just bootloop rather starting in recovery.
Click to expand...
Click to collapse
I already tried going into recovery mode with the phone turned on without bootloop problem!
I'd like to know if this is a correct procedure or not, because there are people who say they can usually do.
---------- Post added at 08:01 PM ---------- Previous post was at 07:33 PM ----------
zeeshanonlyme said:
Are you asking if you can go into Recovery or Download mode when your phone is on,ie,w/o switching it off?
Yes you can.For recovery mode press up volume+home+power(strangely enough any combo works.power+home+volume but keep them pressed till the phone reboots and you see the Samsung GT-N7000 logo then u can let go.
For Download mode press down volume+home+power(again in any combo)
Hope i answered your question
Click to expand...
Click to collapse
Yes!
Thanks a lot.

Lots of people have bricked their phone while repartitioning and using PIT.
I would say read carefully when you try it.
If I ever get superbricked I'd just kill it with Angelom test kernel or if I want to return to clean state - I'd flash any safe kernel - perform factory reset, format system partition and sd card then flash latest stock firmware available for my region.

doesn't work
it stops by "Hidden"
<ID:0/005> factoryfs.img
<ID:0/005> hidden.img
I let it for 1 hour, but it's not working... Can someone tell me what I'm doing wrong

Galaxy Note GT-N7000 Modem locked
My Galaxy Note GT-N7000 I purchased this Cell phone in europe it was not working as 3 G on Tmobile I flashed modem, after that I was not able use as cell when I try to call getting insert the SIM card. My SIM is there please Help

Hey i managed to use the odin software to load the gb firmware onto my phone but now when i tr to boot up the phone just hangs at the smasung logo. did i do something wrong or do i need to load something else onto the phone using odin?

lolgical said:
Hey i managed to use the odin software to load the gb firmware onto my phone but now when i tr to boot up the phone just hangs at the smasung logo. did i do something wrong or do i need to load something else onto the phone using odin?
Click to expand...
Click to collapse
Reboot into recovery and wipe cache and data.

Flashing Stock Rom Via SP Flash Tool[Lenovo A7000]

PART-A
1.Download Stock Rom
-------------------------For Marshmallow:-click here
-------------------------For Lolipop:-click here
2.Installing driver (included in ROM package).
3.Then copy and extract Stock Rom package in pc.
4.ENABLE USB DEBUGGING
Go to Settings>> About>> Build number and tap it 7 times to unlock Developer options. Then return to Settings>> Developer options and tick the USB Debugging option.
PART-B
INSTALL STOCK ROM ON LENOVO A7000 ROW VERSION
NOTE: Before doing this process make sure you have backup of contacts, SMS, call log or files in internal memory. As it will format your whole phone.
1. Charge your phone up to 80% and disable all those firewalls or antivirus on your PC.
2. Run as Administrator the flash_tool.exe, that you will find in the stock rom package.
3. Click on “Scatter-loading” and browse the scatter fileMT6752_Android_scatter.txt,you will find this in target_bin folder inside the A7000-a_S223_160000_ROW folder.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4.In the menu “Option” tab, go to “Download”, and put a “tick” in the “DA DL All with Checksum.
5. Now choose the "Download only" option like this
6. Now hit the Green Download button
7. Now turn off the phone and remove the battery for at least 5 seconds, then put the battery back.
8. Connect your Phone to PC via USB, this will start the flashing process.( if the flashing not started then you are having some driver or connectivity problem)
9. Once the process has completed, we will see a huge green check box.
10. Now we can disconnect the phone from the cable.
Now switch on your phone, it will take 6-10 minutes for first boot.
11. You have successfully installed the stock ROM or Official ROM on Lenovo A7000 ROW version.

PrashantRana said:
PART-A
1.Download latest stock rom.click here
2.Downloading and installing driver click here
3.Downloading SP flash tool click here
Then copy and extract Stock Rom and SP flash tool in your PC.
4.ENABLE USB DEBUGGING
Go to Settings>> About>> Build number and tap it 7 times to unlock Developer options. Then return to Settings>> Developer options and tick the USB Debugging option.
PART-B
INSTALL STOCK ROM ON LENOVO A7000 ROW VERSION
NOTE: Before doing this process make sure you have backup of contacts, SMS, call log or files in internal memory. As it will format your whole phone.
1. Charge your phone up to 80% and disable all those firewalls or antivirus on your PC.
2. Run as Administrator the flash_tool.exe, that you will find by extracting SP_Flash_Tool_v5.1604.zip.
3. Click on “Scatter-loading” and browse the scatter fileMT6752_Android_scatter.txt,you will find this in target_bin folder inside the A7000-a_S223_160000_ROW folder.
4.In the menu “Option” tab, go to “Download”, and put a “tick” in the “DA DL All with Checksum.
5. Now choose the "Download only" option like this
6. Now hit the Green Download button
7. Now turn off the phone and remove the battery for at least 5 seconds, then put the battery back.
8. Connect your Phone to PC via USB, this will start the flashing process.( if the flashing not started then you are having some driver or connectivity problem)
9. Once the process has completed, we will see a huge green check box.
10. Now we can disconnect the phone from the cable.
Now switch on your phone, it will take 6-10 minutes for first boot.
11. You have successfully installed the stock ROM or Official ROM on Lenovo A7000 ROW version.
Click to expand...
Click to collapse
Thanks a lot man!!
For this.

Thanks For Sharing Your Hard Work:good::good::good:

currently flashing MM from Lollipop Stock,25% over
If I do not like stock MM, can I simply flash back the stock Lollipop ?
I have a backup of the Lollipop Rom from TWRP which is rooted and has all my apps. how do I recover from that if needed?
need to send my phone to service center so flashing this stock rom.

karthikx10 said:
currently flashing MM from Lollipop Stock,25% over
If I do not like stock MM, can I simply flash back the stock Lollipop ?
I have a backup of the Lollipop Rom from TWRP which is rooted and has all my apps. how do I recover from that if needed?
need to send my phone to service center so flashing this stock rom.
Click to expand...
Click to collapse
Yes you can also flash stock lolipop by this spflash tool method.
http://forum.xda-developers.com/lenovo-a7000/development/stock-firmware-lenovo-a7000-t3205521

PrashantRana said:
Yes you can also flash stock lolipop by this spflash tool method.
http://forum.xda-developers.com/lenovo-a7000/development/stock-firmware-lenovo-a7000-t3205521
Click to expand...
Click to collapse
flashed it..thanks MM too battery hog and unnecessary sd card issues.

PrashantRana said:
PART-A
1.Download Stock Rom
-------------------------For Marshmallow:-click here
-------------------------For Lolipop:-click here
2.Downloading and installing driver click here
3.Downloading SP flash tool click here
Then copy and extract Stock Rom and SP flash tool in your PC.
4.ENABLE USB DEBUGGING
Go to Settings>> About>> Build number and tap it 7 times to unlock Developer options. Then return to Settings>> Developer options and tick the USB Debugging option.
PART-B
INSTALL STOCK ROM ON LENOVO A7000 ROW VERSION
NOTE: Before doing this process make sure you have backup of contacts, SMS, call log or files in internal memory. As it will format your whole phone.
1. Charge your phone up to 80% and disable all those firewalls or antivirus on your PC.
2. Run as Administrator the flash_tool.exe, that you will find by extracting SP_Flash_Tool_v5.1604.zip.
3. Click on “Scatter-loading” and browse the scatter fileMT6752_Android_scatter.txt,you will find this in target_bin folder inside the A7000-a_S223_160000_ROW folder.
4.In the menu “Option” tab, go to “Download”, and put a “tick” in the “DA DL All with Checksum.
5. Now choose the "Download only" option like this
6. Now hit the Green Download button
7. Now turn off the phone and remove the battery for at least 5 seconds, then put the battery back.
8. Connect your Phone to PC via USB, this will start the flashing process.( if the flashing not started then you are having some driver or connectivity problem)
9. Once the process has completed, we will see a huge green check box.
10. Now we can disconnect the phone from the cable.
Now switch on your phone, it will take 6-10 minutes for first boot.
11. You have successfully installed the stock ROM or Official ROM on Lenovo A7000 ROW version.
Click to expand...
Click to collapse
sir...the download link u provided was not working.....please update that link

Thanks a lot very helpful

Works. But unable to connect to internet and remains in boot loop!

Please fix the links, I'd like to try the stock rom again.

heavencanwait said:
Please fix the links, I'd like to try the stock rom again.
Click to expand...
Click to collapse
Bro I find driver link not working so I have removed link as driver are included in ROM package.
If u find any problem the reply

Hi i flash the stock rom, everything okey but when i boot my phone it shows gray/white screen ... What happened? How to fix it
Im on a7000a 5.0 try to update with this 6.0 on the link of this thread...
Any help is appreciated

seferismo said:
Hi i flash the stock rom, everything okey but when i boot my phone it shows gray/white screen ... What happened? How to fix it
Im on a7000a 5.0 try to update with this 6.0 on the link of this thread...
Any help is appreciated
Click to expand...
Click to collapse
This problem occur when you do not tick the usb checksum and storage checksum in spflash tool settings.
So tick these in settings

PrashantRana said:
This problem occur when you do not tick the usb checksum and storage checksum in spflash tool settings.
So tick these in settings
Click to expand...
Click to collapse
i already tick those... thanks
whats suppose to be the problem

Hi there, i am trying to help a friend re-flash his Lenovo A7000-A phone back to stock firmware but it after reading about it, i've come to know that the phone has two types of firmware ROW-rest of the world version and one other which is probably chinese. i was wondering if that is true and where i could get the non-ROW version. your help would be much appreciated. thanks

Is there any option to update from S133 to S136 (for example) via SP Flash Tool without wipe any userdata - like OTA update?

NOT GOOD. I have downloaded the Lollipop package from the link in the first post.
1. After applying it as described, the Home and Back button stopped working! Tried eMMC factory reset and did not help.
2. The OS occupied space still reported to be 3.13 GB, exactly the same as in Marshmallow!
Now I am trying to perform OTA update back to Marshmallow to see if the buttons would work again, even though I doubt they would...
BTW, in the Flash Tool >> Options >> Download >> there was just a single checkbox available: "DA DL All with Checksum" (version v5.1436.0, DA_v7.1436.00.000, libflashtool.so vBROM_DLL_v7.1436.01).

PrashantRana
Click to expand...
Click to collapse
Hi friend, thanks for this tutorial.
I did all steps successfully, first as you said tick both options in download and done. But when I turned on phone see a Gary and white screen for a few second and then black, noting happened.
As you reply on another question like me I tried all steps but this time not tick the check box's in option. This time after turned on phone, just black screen. So again I do all steps as you said with tick in option. But again I face gray and white screen and noting loaded.
Can you help me on this ?
Tip: first time try this tutorial a face an error so I searched it and the answer was: first flash the device. So I flashed phone from flash tab in so flash tool then I tried this tutorial.
Thanks a lot for your time.

Thanks.
God Job.
No Problem.

Hi! I succesfully downgraded my phone to android 5.0 lollipop. Everything works fine except my sd card -it says my sd is corrupted but that's not true because on android 6.0 marshmallow that sd worked. I also tried different sd card but nothing changed. I even tried to format sd card but it still doesn't work. Is there some way how to fix it ?

Yoga Tab 2 8" 830f failed update led to soft lock

So I downloaded a 16mb OTA update and let the tablet do its thing without touching it. I waited for the tablet to boot up, but it was stuck in a black screen for about 12 minutes until I decided to turn it off and on. It didn't work, so I went to the recovery to do a factory reset and clear the cache, but it still didn't work. I later went to this Russian forum here from this thread. I downloaded a lollipop rom and proceeded to flash it using Phone Flash Tool Ver. 5.2. It went well until 16% in where it failed. Unfortunately, I don't have a screenshot of this.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(image of the files in the rom I downloaded)
After all this happened, I tried to start it up but I got the message "Boot Failed. EFI Hard Drive. Boot Successful - Enter Setup"
And now it won't go into recovery mode, but it does go into fastboot and bios setup.
Since it does go into fastboot, I tried to use a tool from this thread (Temp recovery) to use a temporary cwm recovery to hopefully be able to at least boot into that, but that didn't end up working.
I got another rom from the same Russian site that had differently packaged files but still the same stock lollipop rom.
I tried to just use the recovery from there to manually flash it using fastboot, but it still failed.
I later found this thread with these instructions for this problem.
1. download and extract this file someplace on your pc
2. uninstall your existing Phone Flash Tool and from the drivers folder install both files (Intel Phone Flash Tool and Android Driver accepting defaults) reboot pc when finished
3. place your tab in DNX mode (from power off press and hold both volume keys then press pwr to start, in a few you screen will show "Fastboot starting..." message and hang on that. you must get that message on your tab screen, restart from power off until you have it)
4. start the installed Phone Flash Tool and load flash.xml from the extracted YT2-830L... folder then Start Flashing, it will reboot when done
Click to expand...
Click to collapse
The file he linked in his post (ionioni ) was gone but I still tried to do this with the roms I had. And guess what? It still didn't work. The instructions said to place the tablet in DNX mode (meaning fastboot), which I did do...only when I put it into fastboot, it was set to DNX_OS which came to say "Wrong device state" in Phone Flash Tool.
I've tried what I could, but failed. Anyone have any suggestions?

AgentXGhost said:
So I downloaded a 16mb OTA update and let the tablet do its thing without touching it. I waited for the tablet to boot up, but it was stuck in a black screen for about 12 minutes until I decided to turn it off and on. It didn't work, so I went to the recovery to do a factory reset and clear the cache, but it still didn't work. I later went to this Russian forum here from this thread. I downloaded a lollipop rom and proceeded to flash it using Phone Flash Tool Ver. 5.2. It went well until 16% in where it failed. Unfortunately, I don't have a screenshot of this.
(image of the files in the rom I downloaded)
After all this happened, I tried to start it up but I got the message "Boot Failed. EFI Hard Drive. Boot Successful - Enter Setup"
And now it won't go into recovery mode, but it does go into fastboot and bios setup.
Since it does go into fastboot, I tried to use a tool from this thread (Temp recovery) to use a temporary cwm recovery to hopefully be able to at least boot into that, but that didn't end up working.
I got another rom from the same Russian site that had differently packaged files but still the same stock lollipop rom.
I tried to just use the recovery from there to manually flash it using fastboot, but it still failed.
I later found this thread with these instructions for this problem.
The file he linked in his post (ionioni ) was gone but I still tried to do this with the roms I had. And guess what? It still didn't work. The instructions said to place the tablet in DNX mode (meaning fastboot), which I did do...only when I put it into fastboot, it was set to DNX_OS which came to say "Wrong device state" in Phone Flash Tool.
I've tried what I could, but failed. Anyone have any suggestions?
Click to expand...
Click to collapse
This is the file you need https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view
And this https://01.org/android-ia/downloads/intel-platform-flash-tool-lite
Ignore the oops error warning, it's something to do with what G drive can scan.

Holy Sh!t. this just absolutely worked!! I didn't think I could bring this thing back to life, but the files you linked just did it! Really, I don't know how to thank you enough for this.

corasman said:
This is the file you need https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view
And this https://01.org/android-ia/downloads/intel-platform-flash-tool-lite
Ignore the oops error warning, it's something to do with what G drive can scan.
Click to expand...
Click to collapse
Hi folks,
had the exact same issue and indeed the 1st link offered (https://drive.google.com/file/d/0B1LaMEhefCBgYzNTOUxJZmtWQ0E/view) worked like a charm.
The second link is to download the "Intel platform flash tool lite", but I used my existing version of the Intel Phone Flash Tool (5.2.1-0) which worked fine with the image.
In other words, Corasman, it appears you have saved 2 people's life (or at least tablets) with your solution, so Thanks ! :good:
Regards.

Make that 3 people! Thank you so much corasman - your post has finally fixed my yoga 2 tablet, which I was sure would be going in the bin. Can't overstate how grateful I am - Cheers!

update 830f with 1050f rom?
updating 830f with 1050 rom? does it work?

hello. I have the same problem. I update OTA to lolipop. Since the table is slow, i tried flashing some ROM (which i cannot recall) and the tablet stopped working. Now, I am trying to flash the link you provided and it succeed. However after that i get blank Screen. what Could be wrong. My table is YT2 830LC. Please help

I am typing this all over again after my full report vanished. Do not have the patience of typing all that again. Suffice to say I had a similar situation with the boot failed EFI Hard Drive. Boot Successful - Enter Setup" message on my 830LC.
I had even found the bios restore tool for moving back from lollipop to kitkat but it too would hang. And attempts to flash lollipop would fail immediately with the same message as the OP, wrong device state.
So, in spite of it seeming completely counter-intuitive, I flashed the 1050F rom in the link shared by Corasman. Strange as it may seem, my tablet is now alive and working. No calling function, but it is working and calling itself a 1050F.
Now my research has to shift to whether the 830 LC rom can be flashed now.

i have a same problem with yoga 2 pro 1380f mr corasmancan help me

prabuddhadg said:
I am typing this all over again after my full report vanished. Do not have the patience of typing all that again. Suffice to say I had a similar situation with the boot failed EFI Hard Drive. Boot Successful - Enter Setup" message on my 830LC.
I had even found the bios restore tool for moving back from lollipop to kitkat but it too would hang. And attempts to flash lollipop would fail immediately with the same message as the OP, wrong device state.
So, in spite of it seeming completely counter-intuitive, I flashed the 1050F rom in the link shared by Corasman. Strange as it may seem, my tablet is now alive and working. No calling function, but it is working and calling itself a 1050F.
Now my research has to shift to whether the 830 LC rom can be flashed now.
Click to expand...
Click to collapse
i have same problem with my yoga 830lc this rom not work help me to run my tab agian
---------- Post added at 10:55 AM ---------- Previous post was at 10:47 AM ----------
corasman said:
This is the file you need
And this
Ignore the oops error warning, it's something to do with what G drive can scan.
Click to expand...
Click to collapse
hy sir downlod the rom from google drive but unable to download 2nd link (link not working)
i use latest intel flas tool light but the rom no flash to my device its show errors. plese sir help me to run my tab again

Help resting P8 back to complete stock, recovery, system etc.

A few months ago i tried to install busy box and a few other things but busy box broke and I couldn't reinstall or uninstall it. So i tried a custom rom but that ended up in no NAV bars or status bar. Now i downloaded the stock firmware for android 5.0 from Huawei's Australian website, extracted boot.img system.img recovery.img and flashed them. (I used to have TWRP) Now the recovery is nothing, it just auto reboots, and the system has no sound and does not charge or is detected by a computer (How ever the phone charges when its off/in fast boot etc, it only doesn't work when in android.) Im not sure what region of firmware the phone had originaly as I bought it from a site called Android Enjoyed and it came with a British charger, so yeah, not sure if it had UK firmware or not. I am in Australia. The model on the back and in the OS is the GRA-UL00 and it is dual sim. I just need help to reset the phone completely back to stock and what I need to download. Any help is massively appreciated !

Bump. I really need some help here, I'm at a loss on what to do after hours of googling and searching the forums.

Well, as far as I know, the GRA-UL00 dual-sim version was never officially sold in the UK, so it couldn't have been from here originally (I'm in the UK).
Can you ask Android Enjoyed where it was from originally?
What does it display in ProjectMenu [to access: dial *#*# 2846579#*#*] > Network Information Query > Vendor Country Info:
Vendor: ??
Country: ??

GaT7 said:
Well, as far as I know, the GRA-UL00 dual-sim version was never officially sold in the UK, so it couldn't have been from here originally (I'm in the UK).
Can you ask Android Enjoyed where it was from originally?
What does it display in ProjectMenu [to access: dial *#*# 2846579#*#*] > Network Information Query > Vendor Country Info:
Vendor: ??
Country: ??
Click to expand...
Click to collapse
Ill give that a go once it charges up again, how ever if that is something affected by the software it might be wrong if I have installed the wrong region of android. I googled the British charger and It looks the same, maybe you can confirm for me? Thanks.
Ok apparently I lost the charger but it looked just like this one.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
EDIT: Dialed in that number and went to country vendor info to get
Vendor: Vendor Country file does not exist
Country: Vendor Country file does not exist
welp.

Bump. Pls. I dont know where to look next. Any thing someone can contribute.

Reading your initial post again, I can see you were on the right track in trying to rescue it.
Also, I'm assuming this is the stock Android 5.0 firmware you downloaded from Huawei Australia & extracted+flashed the files from:
HUAWEI P8 Firmware (GRA-UL00, Android 5.0, EMUI 3.1, C470B200, Southern Pacific Region)
After installing the above, did you try a factory reset & cache wipe in Recovery mode, then rebooting? If not, during the bootloop, just as it's going to bootup again, hold down the Power & Volume up buttons simultaneously until you get to Recovery mode (view 1st thumbnail pic). You may need to try a few times to get the timing right. Once in Recovery mode, do a 'Wipe data/factory reset' & 'Wipe cache partition', then reboot. Any different after rebooting?
If that doesn't work either, have you tried flashing the boot, recovery & system image files from any other firmware that you've not mentioned? If you've not tried one firmware previous, then do it. I believe B180 is one previous to B200 & can be downloaded from here:
HUAWEI P8 Firmware (GRA-UL00, Android 5.0, EMUI 3.1, C470B180, English, Southern Pacific Region)
If you cannot flash the extracted files from B180 as the phone is still bootlooping, plug in the USB cable from your switched-on computer. Then just after it reboots (during its bootloop sequence), hold down Power & Volume down buttons simultaneously until you get to the Fastboot&Rescue mode screen (view 2nd thumbnail pic). Like before, you may need to try a few times to get the timing right. Once there, type 'fastboot devices' via your computer's ADB command prompt to see if the phone is being recognised properly. Then issue the commands to flash the extracted files. Finally, as above, try a factory reset & cache wipe in Recovery mode as well.
If it still doesn't work, try the same steps as above with B150 (the earliest firmware for your model I could find):
HUAWEI P8 Firmware (GRA-UL00, Android 5.0, EMUI 3.1, C470B150, Southern Pacific Region)

Yes that first link is the one I ended up installing. The phone doesn't bootloop, it just has no sound and doesn't charge while in android. Also the boot animation is different from what it was originally which is also convincing me i don't have the right one. (The animation is now just the android logo instad of the huawei logo it used to be ) I think recovery isn't working anymore but I will try once it charges up. I'll give what you said a go and report back.
GaT7 said:
Reading your initial post again, I can see you were on the right track in trying to rescue it.
Also, I'm assuming this is the stock Android 5.0 firmware you downloaded from Huawei Australia & extracted+flashed the files from:
HUAWEI P8 Firmware (GRA-UL00, Android 5.0, EMUI 3.1, C470B200, Southern Pacific Region)
After installing the above, did you try a factory reset & cache wipe in Recovery mode, then rebooting? If not, during the bootloop, just as it's going to bootup again, hold down the Power & Volume up buttons simultaneously until you get to Recovery mode (view 1st thumbnail pic). You may need to try a few times to get the timing right. Once in Recovery mode, do a 'Wipe data/factory reset' & 'Wipe cache partition', then reboot. Any different after rebooting?
If that doesn't work either, have you tried flashing the boot, recovery & system image files from any other firmware that you've not mentioned? If you've not tried one firmware previous, then do it. I believe B180 is one previous to B200 & can be downloaded from here:
HUAWEI P8 Firmware (GRA-UL00, Android 5.0, EMUI 3.1, C470B180, English, Southern Pacific Region)
If you cannot flash the extracted files from B180 as the phone is still bootlooping, plug in the USB cable from your switched-on computer. Then just after it reboots (during its bootloop sequence), hold down Power & Volume down buttons simultaneously until you get to the Fastboot&Rescue mode screen (view 2nd thumbnail pic). Like before, you may need to try a few times to get the timing right. Once there, type 'fastboot devices' via your computer's ADB command prompt to see if the phone is being recognised properly. Then issue the commands to flash the extracted files. Finally, as above, try a factory reset & cache wipe in Recovery mode as well.
If it still doesn't work, try the same steps as above with B150 (the earliest firmware for your model I could find):
HUAWEI P8 Firmware (GRA-UL00, Android 5.0, EMUI 3.1, C470B150, Southern Pacific Region)
Click to expand...
Click to collapse

Singularity_iOS said:
Yes that first link is the one I ended up installing. The phone doesn't bootloop, it just has no sound and doesn't charge while in android. Also the boot animation is different from what it was originally which is also convincing me i don't have the right one. (The animation is now just the android logo instad of the huawei logo it used to be ) I think recovery isn't working anymore but I will try once it charges up. I'll give what you said a go and report back.
Click to expand...
Click to collapse
Hi, how did it go?

GaT7 said:
Hi, how did it go?
Click to expand...
Click to collapse
Hey I know its been a month but I still haven't gotten around to trying it yet lol. I'll give it ago tomorrow if I remember. I'll let you know how it goes

[GUIDE] Samsung Galaxy S7 Active (G891A) FRP Bypass Method Using Odin

This is the entire process needed to remove FRP protection from your AT&T Samsung Galaxy S7 Active (G891A). Tested and working on Android 7.0 (2/26/18)​
Summary​ This process involves using a modified version of Odin to flash an unlocked bootloader. With the unlocked bootloader you can gain adb permissions and use adb commands to wipe the files that store the FRP credentials. After wiping the credentials, you will flash your device back to the original stock 7.0 firmware. This does not root your device. This does not trip knox.
Process​The Download is 2GB. It will take a few minutes to download. This is necessary because it contains all the original firmware to return your phone to stock.
Download: S7 FRP Bypass Kit
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 1: Download the files and open the modified Odin.exe
Step 2: Hold the Power, Home, and Volume Down buttons until your phone shows a green screen. Then release those buttons and press the volume up button to place your device in download mode. Once your phone is in download mode, connect it via usb to your computer running Odin. The COM port box in Odin should turn blue indicating a successful connection.
Step 3: In Odin click the AP button and open the file AP_G891A_7.0_eng_boot.tar. Ensure that the checkbox beside the AP button is checked and then click start. Give the program a few minutes to execute. Your phone will reboot when flashing is complete.
Step 4: Once your phone is rebooted, you should now be able to connect to it via ADB. I have created a simple .bat file to automatically do this for you. With your phone running, double click on Step4.bat and allow it to run for a minute or so. Pay attention to the window and ensure that it is making a connection. If the window continues to show "No Devices Found" then you need to repeat steps 2 and 3. If you were successful in running the .bat program then reboot your phone like normal and now you should be able to enter a new email account on the setup screen as if the phone is new. ***DO NOT STOP HERE***
Step 5: Hold the Power, Home, and Volume Down buttons until your phone shows a green screen. Then release those buttons and press the volume up button one to place your device in download mode. Once you are in download mode again, connect your device to the computer if you unplugged it previously. Ensure that Odin detects your device.
Step 6: Now you need to reflash the stock 7.0 firmware. With Odin open and your phone connected, click the BL button in Odin and navigate to the S7 Active Stock Firmware folder in the package you downloaded. In this folder are the stock files that correspond to the buttons in Odin. Put the BL, AP, CP, and CSC files in their respective places and click start. Don't be alarmed if Odin stops responding for a minute or two while loading the files. The AP file is rather large.
Once this finishes and your phone reboots you will have a stock FRP unlocked S7 Active just like it was brand new.
Disclaimer: Do this at your own risk. I broke down the instructions as basic as I could, but you should have general Rom flashing knowledge / experience prior to doing this.

Removed

could really really use some help if you have time
MY PHONE KEEPS FREEZING**GETTING STUCK BOOTING NO.MATTER WHAT I DO I HAVE TO ATLEAST ONCE A DAY EITHER FACTORY RESET MY PHONE OR CLEAR CATCH AND HARD RESET MY PHONE OVER AND OVER AGAIN...I LOVE MY PHONE BUT AT THIS POINT WITH NO PRIOR TECH KNOLEDGE IM DESPERATE FOR HELP! OR I WILL HAVE TO GET RID OF IT.
********** I am sure your busy. I could seriously use your help ...so I have ZERO flashing experience.. And to be honest I was a sheep as far knowing anything about custom Roms, flashing etc. I own a Galaxy s7 active with the up to date newest build number.. however I am a T-Mobile customer and had to receive the OTA updates by buying AT&T SIM...i had no CLUE how much trouble I was going to have with this phone running on TM network...And you will certainly be more aware with what my problem is then I am i have talked to 20+tech's from T-mobile and at&t to fix my problems to ONLY END UP BEGAN! I've done everything short of smashing this thing to get it to work....please if you can find the timein your busy life to help me I PROMISE YOU it will look good in front of the big man in the sky as a GOOD DEED lol...listen I'll even give you my phone number to call me if you want...i just want my phone to work...btw not a ram problem I only have 3 apps but would love to get rid of at&t bloatware...anything you can do to help is appropriate more then you'll ever know E mail* [email protected]

Worked perfectly! Thank you so much.

Phone gets stuck at boot after step 3
Edit : Fixed by flashing stock rom first then flashing the modified bootloader. Working great now with frp removed thanks again

so wait... something like this opens the bootloader to flash custom roms and twrp?
that'll brake knox for sure... but it is possible now? can we take S7/s7 edge roms and teak em to use active button?

S7activehelpme said:
MY PHONE KEEPS FREEZING**GETTING STUCK BOOTING NO.MATTER WHAT I DO
Click to expand...
Click to collapse
Flash stock rom first in step 4 then begin at step 1 again because the modified bootloader isn't compatible with the version of android that's currently on your device

i have a Verizon (well straight talk) smg930vl which im told is factory sim unlocked, planning to use att sim.
you think your process will work for my phone? ( att software on Verizon phone?)and for that matter s7 vs s7 active. or should i use the modded bootloader to get passed frp then flash stock Verizon?

dkiller10002 said:
i have a Verizon (well straight talk) smg930vl which im told is factory sim unlocked, planning to use att sim.
you think your process will work for my phone? ( att software on Verizon phone?)and for that matter s7 vs s7 active. or should i use the modded bootloader to get passed frp then flash stock Verizon?
Click to expand...
Click to collapse
No that is not what this is. You will have to get the unlock code from verizon, even then it will be limited on what it can use on the att network. like no wifi calling or RCS

binary error
Never mind I fixed the binary error. However when I load up all the bl ap cp csc etc, odin gets stuck at file analysis

Hey mate , which stock did You use , and what does the second part meant ?

So, if this unlocks the bootloader, could I flash a custom rom to it now?

This worked like a charm. Thank you so much.
brs

Anyone have any info on how to bypass the FRP on SM-G930T variant, running G930TUVS4BRC1 (latest patch)?
will this work for my particular model and patch?

Work perfectly. Big Thank you!!!!!

Watching the screen for step 4, I keep seeing a message that says no space left on this device and the program keeps running over and over. Ideas?

password
its asking me for a password....

how long should the bat4 take to run?

I got the first 4 steps but when I try to actually flash the rom I get FAIL!(Auth) and on the phone it says "SW REV check fail: [aboot]Fused 3 > binary 2" Is there anyway to fix this? TIA

hi will this work with my s7 active being on oreo or is this only for nougat? G891AUCU3CRD6