Related
This ROM is based on Nightly version AICP but its Stable for daily use.
FEATURES:
All AICP features
Lollipop features (customized by AICP)
BUGS:
Unresized BootAnimation [on the center] (I did this on purpose, if you want you can change.)
Sees there is a sim card in tablet but there isn't. [Says "NO SERVICE"] (You can disable with " Permanent GSM solution down below)
Little bugs [does not affects daily use]
Can't install GAAPS because system partition is small (FIXED IN VERSION 2 ! - FIXED IN V2 !)
_-----------------------------------------------_
Permanent GSM solution:
1) not avaliable instructions
2) when way to disable cellular its entered ti here
INSTALLATION:
1. Install TWRP Recovery [if you haven't]
2. Boot into recovery mode
3. Wipe "System,Data,Cache,Dalvik Cache"
4. Flash ROM file from install zip section
Note: If you will flash GAAPS don't reboot after flashing system, flash GAAPS before rebooting.
Note2: Download v2 if you need flashing GAAPS.
XDA:DevDB Information
AICP SM-T800, ROM for the Samsung Galaxy Tab S
Contributors
romngenie
ROM OS Version: 5.1.x Lollipop
ROM Firmware Required: TWRP
Based On: AICP
Version Information
Status: Stable
Created 2016-06-25
Last Updated 2016-06-25
hello, after searching I've found out that AICP stand for Android Ice Cold Project. May I ask if it look like Cyanogenmod or the AOSP ? first time I hear about it...
and just to know, why isn't it on the list of : http://dwnld.aicp-rom.com/?device=all&type=all ? for the chagallwifi T-800 ?
zigonneux said:
hello, after searching I've found out that AICP stand for Android Ice Cold Project. May I ask if it look like Cyanogenmod or the AOSP ? first time I hear about it...
and just to know, why isn't it on the list of : http://dwnld.aicp-rom.com/?device=all&type=all ? for the chagallwifi T-800 ?
Click to expand...
Click to collapse
Because i just created a XDA project. I cant contacted to AICP
Sent from my Asus ZenFone 2 Laser (ZE550KL) using XDA Labs
nice rom but some errors: can't check for update. Can't install any gapps because lack of space in the system file. Very fast rom , but can't test anything else.
zigonneux said:
nice rom but some errors: can't check for update. Can't install any gapps because lack of space in the system file. Very fast rom , but can't test anything else.
Click to expand...
Click to collapse
System partition is 300-450 MB i dont know why you can't install GAAPS (Fixed in V2 of ROM)
Can't check for update because its unofficial and no more updated . (except bug fixes)
Thanks for installing.
zigonneux said:
nice rom but some errors: can't check for update. Can't install any gapps because lack of space in the system file. Very fast rom , but can't test anything else.
Click to expand...
Click to collapse
YOU CAN INSTALL GAAPS LIKE THIS: (GAAPS FIXED IN V2 - TRY V2 WITHOUT ANY "occupation")
1. Download and install V2 of the ROM.
2. Install Gaaps.zip (install pico)
download says: Uploaded: 2016-Jul-19 , so I guess that the Fixed file is not there yet. I'll wait for the Fix and test for the fun of it... post the link when the fixed file is ready. I'm too lazy to deal with the Solution : decompress and recompress etc.
zigonneux said:
download says: Uploaded: 2016-Jul-19 , so I guess that the Fixed file is not there yet. I'll wait for the Fix and test for the fun of it... post the link when the fixed file is ready. I'm too lazy to deal with the Solution : decompress and recompress etc.
Click to expand...
Click to collapse
GAAPS is fixed in V2 version.
http://forum.xda-developers.com/devdb/project/dl/?id=19411
there is V2 Link.
You dont need uncompress and other techniques for this. Just download V2 and your GAAPS will fixed.
And i know i dont update this ROM except bug fixes.
SM-T800 cihazımdan Tapatalk kullanılarak gönderildi
Updated on 17th March 2019
I am not responsible for brick your devices, Please flash at your own risk, but i tested, i can help you save brick devices also, can contact me anytime at hangouts.
Note:
I developed this ROM and tested as well,
Change log: 17/03/2019
1: Synced latest Source
2: Embedded March 05 Security patch
3: Minor fixes with Mokee device Trees
4: NFC (please Check and confirm)
What's not working:
Please tell.
Hey Folks:
Always bring something new and different for Victara device,
Lineage MOS. 8.1.0 Unofficial (STABLE VERSION) for Victara Moto x2 2014 Developed by weibo.com/diyroms
Lineage Unofficial 8.1.0, developed by Montana team. link: https://github.com/montanadevelopment
Credits: All Montana Development Team
Credits: Micheal Chen and team for MOS (Moonlight OS, Lineage 8.1.0)
Dated: 03rd June 2018
Battery life is very very good in this stable version
What's not working
1: Pattern lock late response first time.
2: HDR (waiting for Fix)
Other you can tell
What's Working:
1:Almost everything you need for daily use
2: Video recording working
Other you can check and report bugs for improvement
What you need:
MOTO X2 2014 Victara device
( Unlocked boot loader having TWRP 3.2.1.0 old versions won't work for 8.1)
[GUIDE] (Please Read after point 5 with concentration)
1: Download ROM and Unofficial 8.1 Gapps nano or as your taste from below links
2: Open TWRP and prepare all internal storage backup and your NANDROID backup.
3: Open Wipe, Advance Wipe and Change file system and Format Data, system, Cache with ext4
This will erase all your data (If you are already at ext4 then no need to wipe with ext4)
4: Now in TWRP connect device with PC or have a OTG USB with files and copy files in internal storage i.e. ROM zip and gapps zip
5: Now flash ROM zip and reboot system and setup everything in Lineage setup
6: You will see some Chinese apps, You can remove them by Root uninstaller, this ROM is rooted by default.
7: Go to setting, developer options and click advance reboot.
8: Now reboot to Recovery and go to gapps and flash then reboot. (You must have latest gapps from opengapps.org or you will need to update play services manually)
Here you done.
Source: https://github.com/LineageOS/android/tree/lineage-15.1
Kernel: https://github.com/zahidmgsk/android_kernel_motorola_msm8974
Device Trees: https://github.com/zahidmgsk/android_device_motorola_victara/tree/mko-mr1
Vendor: https://github.com/TheMuppets/proprietary_vendor_motorola/tree/lineage-15.1
If any issue please ask me at G+ anytime
Download Link Lineage 15.1 Unofficial Gdrive 11.04.2019
https://drive.google.com/file/d/1Ql5xw9I_UlGUC6gfOKI9it-N-e7hVmqV/view?usp=drivesdk
Download Link for MOS. Stable Version 5.0 Dated 12.11.2018
https://mega.nz/#!5j4iyQzT!21w7uH3OoldpEB68Sh7jLTWFLKDQdyg9JEZxZhC2i84
Version 5.0 updated on 12.11.2018
GAPPS Official 8.1.0: LINK
https://opengapps.org/
ALL DONE HERE
i have already tested this ROM Very good battery and smooth ROM... as far as will get next Update then share according...
SEE YA...
Reserved and SS @Archangel try this
Did the NFC work?
ColorfulNight said:
Did the NFC work?
Click to expand...
Click to collapse
I don't think so, because still there js no fix for victara 8.1,
zahidm said:
I don't think so, because still there js no fix for victara 8.1,
Click to expand...
Click to collapse
Nice to see an actual LOS build! thank you. Did you included patches for Camera HAL1? Will test on weekend when i find some time.
bejunk said:
Nice to see an actual LOS build! thank you. Did you included patches for Camera HAL1? Will test on weekend when i find some time.
Click to expand...
Click to collapse
I sent all data to Chen you can check and verify if not than i can ask him to add in next build.
what does MOS stand for? I know Lineage "OS" is Operating System
renzs said:
what does MOS stand for? I know Lineage "OS" is Operating System
Click to expand...
Click to collapse
After L there is M so we made it MOS ?
Always on display
Does it support Always on display, I mean is there any setting to set ambient display to always on?
What about pixel style navigation bars?
Nirmal Rai said:
Does it support Always on display, I mean is there any setting to set ambient display to always on?
What about pixel style navigation bars?
Click to expand...
Click to collapse
Yes there is always on setting, and this is actual lineage source so no pixel style navigation bar.
Battery
Battery life if always on display enabled?
Nirmal Rai said:
Battery life if always on display enabled?
Click to expand...
Click to collapse
Yes i am using user awake display and i got about 3 hours 25 min of screen on time.
Hello, could you please provide the link for the source code?
Won't support multilanguage...
jeferson1979 said:
Won't support multilanguage...
Click to expand...
Click to collapse
Yes it is, please follow procedure property
zahidm said:
Yes it is, please follow procedure property
Click to expand...
Click to collapse
Im using pico gapps, and done all the recommended, will try with nano or mini
jeferson1979 said:
Im using pico gapps, and done all the recommended, will try with nano or mini
Click to expand...
Click to collapse
So you have no multi language support? You flashed ROM and Gapps together?
InnerSanctum said:
Hello, could you please provide the link for the source code?
Click to expand...
Click to collapse
Hey it's really easy to download build sources, but huge files you tried a Git hub?
zahidm said:
So you have no multi language support? You flashed ROM and Gapps together?
Click to expand...
Click to collapse
Do it step by step. with stock gapps, same result, the rom only shows english and chinese, gapps are on pt-br, but system still as reported.
Sorry for my bad english
jeferson1979 said:
Do it step by step. with stock gapps, same result, the rom only shows english and chinese, gapps are on pt-br, but system still as reported.
Sorry for my bad english
Click to expand...
Click to collapse
After flashing go to system, language and add a language and tell me how many languages are there..
And also try these gapps in link below..
https://mega.nz/#!BuJx0CQT!dt5SKKnWT5aFkvYPUkcn5vPI2AW0zK47r479pkqmtWk
Most anticipated news. At last Treble Support for our Redmi 3 (Ido) devices.
Ariafan and WinKarbik made this project for us. What they did - he shared the HALs (Hardware Abstraction Layers simpler - vendor) from the Android Framework, used the cust section (which is useless on custom), moved HALs (vendor) into it. Now we can use this project, there are assemblies from official teams.
Xposed and Substratum work fine, magisk modules are not everything, usual modules and patches look rebuilt under treble, the ways of mounting have changed.
This is from Ariafan
crDroid Treble
On top of it (with standard wipes) you can put GSI firmware (I tested AOSP 8.1 from phhuson). I (Redmi 3 2/16) from the "iron" did not work only taking photos in the stock camera (the video shoots, and they say in Cameringo there is a photo shoot, but I did not check it). Installation through any Recovery with Project Treble support
Download rom: https://yadi.sk/d/EKRUczm33aD7VU
Rom description: CrDroid v4.5, Oreo 8.1
Build date: 2018-08-13.
Our Device is A only. Flash A only gsi.
Credit: Ariafan, Winkarbik from 4pda
Enjoy and hit Thanks below.
Use this thread for Treble discussion for Our Ido.
Reserved
thanks for the great work. i prefer to wait for solved camera issue. because i'm too handsome without camera and i like waiting :laugh:
regards.
iwingmusic said:
thanks for the great work. i prefer to wait for solved camera issue. because i'm too handsome without camera and i like waiting :laugh:
regards.
Click to expand...
Click to collapse
just use cameringo
mesandman said:
just use cameringo
Click to expand...
Click to collapse
i always use cameringo for long time. it is already said problem with camera and only photo shoot and haven't tested either for cameringo so i'm not going to test it. i'm currently enjoying RR without any matter. i've tested RR with treble one and it didn't boot.
iwingmusic said:
i always use cameringo for long time. it is already said problem with camera and only photo shoot and haven't tested either for cameringo so i'm not going to test it. i'm currently enjoying RR without any matter. i've tested RR with treble one and it didn't boot.
Click to expand...
Click to collapse
but i've downloaded though :laugh:
Hi,
Great news and good job. I have twrp.3.2.3.0 for ido, is it compatible with this rom/treble? Can you put here a tutorial to flash treble? I'm a noob on this but I would like to give my ido a new live. Thks and good job.
aftrindade said:
Hi,
Great news and good job. I have twrp.3.2.3.0 for ido, is it compatible with this rom/treble? Can you put here a tutorial to flash treble? I'm a noob on this but I would like to give my ido a new live. Thks and good job.
Click to expand...
Click to collapse
https://forum.xda-developers.com/redmi-3/development/unofficial-orangefox-recovery-project-t3804923
Now that I have orange fox, how do I flash this treble cr Droid rom? Thks
aftrindade said:
Now that I have orange fox, how do I flash this treble cr Droid rom? Thks
Click to expand...
Click to collapse
Don't know about OrangeWolf because I'm using RedWolf cust version
-Wipe everything
-Install ROM +Gapp +magisk 16.7
-reboot
aftrindade said:
Now that I have orange fox, how do I flash this treble cr Droid rom? Thks
Click to expand...
Click to collapse
-install your rom treble (cr Droid-8.1-v4.5 20180813 or RR-O-v6.1.0-20180811) reboot system
-back to twrp orangewolf
-wipe : system, data, cache
-mount : data, vendor, cache, microsd
-install image : choose arm64 A - I tested : RR (pphusson), RR (official), Pixel Experience (official) from 4pda
-reboot system
good luck
aftrindade said:
Now that I have orange fox, how do I flash this treble cr Droid rom? Thks
Click to expand...
Click to collapse
i haven't used orange fox either but i always do clean install in every flashing to make sure everything goes well by wiping dalvik, system, data, internal storage & cache then getting rom + gapps into install queue then wiping dalvik again. don't forget to backup internal storage first.
ghue2311 said:
-install your rom treble (cr Droid-8.1-v4.5 20180813 or RR-O-v6.1.0-20180811) reboot system
-back to twrp orangewolf
-wipe : system, data, cache
-mount : data, vendor, cache, microsd
-install image : choose arm64 A - I tested : RR (pphusson), RR (official), Pixel Experience (official) from 4pda
-reboot system
good luck
Click to expand...
Click to collapse
Thank you for the info!
Are the treble roms you tried good for daily usage?
Which one would you recommend?
SciG said:
Thank you for the info!
Are the treble roms you tried good for daily usage?
Which one would you recommend?
Click to expand...
Click to collapse
yes, i have tried both... i think cd droid 20180813 better than rr 20180811
ghue2311 said:
yes, i have tried both... i think cd droid 20180813 better than rr 20180811
Click to expand...
Click to collapse
how did you get rr 20180811 working? failed to finish pixel setup on me.
any working screenshots?
Last crdroid rom boots on my Redmi 3, but Camera app not working. RR still buggy, stuck in boot after installation.
Rdeniro67 said:
Last crdroid rom boots on my Redmi 3, but Camera app not working. RR still buggy, stuck in boot after installation.
Click to expand...
Click to collapse
i don't know much about treble, but if you have flashed treble system image, maybe included when you flashed crdroid that has unworking camera, it means that you could flash/change to rom from any official GSIs from crdroid or rr after, doesn't it?
iwingmusic said:
i don't know much about treble, but if you have flashed treble system image, maybe included when you flashed crdroid that has unworking camera, it means that you could flash/change to rom from any official GSIs from crdroid or rr after, doesn't it?
Click to expand...
Click to collapse
Only Crdroid rom boots, even after I installed it any ohter 8.1 rom (rr , pixel exp.) not booting. I went back to Lineage, it is still 7.1.2 but working without problems for me.
Hello everyone. Today or tomorrow I will push rr treble after fixing some bugs
Team Win Recovery Project 3.x, or twrp3 for short, is a custom recovery built with ease of use and customization in mind. Its a fully touch driven user interface no more volume rocker or power buttons to mash. The GUI is also fully XML driven and completely theme-able. You can change just about every aspect of the look and feel.
Code:
#include <std_disclaimer.h>
/*
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, we will laugh at you.
*
*/
Features:
- Decryption Works
- Backup works
- Wipes Work
- Vibration have some problems
Tips:
Seems that the TWRP can work only on the chinese bootloader, so you have to flash the chinese rom before flash the TWRP
Download:
TWRP 3.3.1-3 Unofficial by mauronofrio
TWRP 3.3.1-0 Unofficial by mauronofrio
Source code:
https://github.com/omnirom/android_bootable_recovery
https://github.com/mauronofrio/android_device_nubia_NX629J
Precompiled Stock Kernel in Use
Donations:
Credits:
Created 2019-08-28
Thanks for making twrp real to global version ?
Diabl0z said:
Thanks for making twrp real to global version
Click to expand...
Click to collapse
As i wrote in the Tips section, this TWRP can work only with chinese bootloader, so you have to flash the chinese rom before flash this TWRP
TWRP 3.3.1-3 NX629J by mauronofrio:
- Removed the black bar on the top of the screen (I missed to remove that from the base source i used)
- Fixed Adb and Mtp, now they both works
- Fixed error about mounting /cust
TWRP 3.3.1-3 Unofficial by mauronofrio
mauronofrio said:
As i wrote in the Tips section, this TWRP can work only with chinese bootloader, so you have to flash the chinese rom before flash this TWRP
TWRP 3.3.1-3 NX629J by mauronofrio:
- Removed the black bar on the top of the screen (I missed to remove that from the base source i used)
- Fixed Adb and Mtp, now they both works
- Fixed error about mounting /cust
TWRP 3.3.1-3 Unofficial by mauronofrio
Click to expand...
Click to collapse
I don't know you know about this thread. but i guess he can help you if you want. Slack testing thread. . just saying captain throwback is a good guy and TWRP developer. Maybe you know him. Just saying. But at last it all depends on him.
methuselah said:
I don't know you know about this thread. but i guess he can help you if you want. Slack testing thread. . just saying captain throwback is a good guy and TWRP developer. Maybe you know him. Just saying. But at last it all depends on him.
Click to expand...
Click to collapse
I'm already in it
mauronofrio said:
I'm already in it
Click to expand...
Click to collapse
Good then ?
any date on when can we expect one for global rom?
Does anyone tried this to flash gsi images?
tillicollide said:
any date on when can we expect one for global rom?
Click to expand...
Click to collapse
Can't make it work for Global roms, they have locked the bootloader.
it says unlocked
Not working in rom global
hoichemgio9x said:
Not working in rom global
Click to expand...
Click to collapse
You need to install the chinese rom to flash the twrp, unfortunately there is a block in the global bootloader
How to root if installed twrp not successful in ROM Global. Help me:laugh:
hoichemgio9x said:
How to root if installed twrp not successful in ROM Global. Help me:laugh:
Click to expand...
Click to collapse
Download Magisk manager app and click on install and select patch file, you need boot.img from the version you have installed, and then flash the img obtained from fastboot with fastboot flash boot magisk_patched.img
Thanks and will this work on the latest 3s variant?
rickylcp said:
Thanks and will this work on the latest 3s variant?
Click to expand...
Click to collapse
Yes
Dose this Twrp support flashing of GSI rom.
I tried atleast 2 gsi rom but never booted.
So rises the question in my mind.
Please reply
rajnathr said:
Dose this Twrp support flashing of GSI rom.
I tried atleast 2 gsi rom but never booted.
So rises the question in my mind.
Please reply
Click to expand...
Click to collapse
I think yes but i used the other twrp and gsi must be ab
Enviado desde mi NX629J mediante Tapatalk
Is there any twrp for global version?
is there any chance this guide can work on redmagic 3s since both devices have exactly same specs and model number
Original thread on :
https://4pda.ru/forum/index.php?showtopic=962408&st=800
Code:
*
Your warranty is now void. We are not responsible for bricked devices, dead SD cards, thermonuclear war or you getting fired because the alarm app failed. Please do some research if you have any concerns about features included in this ROM before flashing it! YOU are choosing to make these modifications and if you point the finger at us for messing up your device, we will laugh at you. Hard & a lot.
*
✪ Pitch Black Recovery 2.9 (Unofficial) by @vladimirs
1. Boot into recovery
Code:
fastboot flash boot twrp.img
2. Flash rom.zip/boot.img and PBRP.zip
3. Reboot to Recovery
NOTE: Always bootloader should be Unlocked
Screenshots please
soliman.sohan said:
Xiaomi Mi A3 (laurel_sprout)
OrangeFox Recovery Stable
Version: R10.0
Maintainer: trkzmn
Initial build for laurel_sprout
https://bit.ly/2MRo1rH
Support chat :
t.me/OrangeFoxChat
There is two way to install it:
- Flash ofrp.zip using twrp
Or
- Extract recovery.img from ofrp.zip
- Flash it using fastboot (fastboot flash boot recovery.img)
- Open recovery
- Flash ofrp.zip
Note: You need to flash orangefox zip after flashing rom
Click to expand...
Click to collapse
You can flash .zip files with this recovery?
Spardantex said:
You can flash .zip files with this recovery?
Click to expand...
Click to collapse
Yes you can
Rajendran Rasa said:
Screenshots please
Click to expand...
Click to collapse
totally changed the post!! :cyclops:
Does anyone have a working link for LineageOS?
Ryakna said:
Does anyone have a working link for LineageOS?
Click to expand...
Click to collapse
no .. not now
Never had a Xiaomi device and i want to buy one. I like mi a3 because AMOLED panel and hardware but want to try MIUI as well.
So, about this:
http://c.mi.com/oc/miuidownload/detail?device=1900372
This is official MIUI for mi a3? There's no major bugs in this one then? Can I expect official MIUI 11?
Thanks in advance guys. I'm new with Xiaomi and want to know what you think.
gborfitz said:
Never had a Xiaomi device and i want to buy one. I like mi a3 because AMOLED panel and hardware but want to try MIUI as well.
So, about this:
http://c.mi.com/oc/miuidownload/detail?device=1900372
This is official MIUI for mi a3? There's no major bugs in this one then? Can I expect official MIUI 11?
Thanks in advance guys. I'm new with Xiaomi and want to know what you think.
Click to expand...
Click to collapse
Are you blind
Crllearly written android one
gborfitz said:
Never had a Xiaomi device and i want to buy one. I like mi a3 because AMOLED panel and hardware but want to try MIUI as well.
So, about this:
http://c.mi.com/oc/miuidownload/detail?device=1900372
This is official MIUI for mi a3? There's no major bugs in this one then? Can I expect official MIUI 11?
Thanks in advance guys. I'm new with Xiaomi and want to know what you think.
Click to expand...
Click to collapse
If you want to use miui then go for miui 10 port.. cz this link is official Android one (9_pie)
soliman.sohan said:
• MIUI 11 (Port) by @bitnet
tiny.cc/mia3miui11
• Pitch Black Recovery (Unofficial) by @vladimirs77
cloud.mail.ru/public/53vZ/45bcqkTPc
• Beast Roms 2.0 (Unofficial) by @mdeejay
bit.ly/2MyIBOx
• Syberia OS 3.0 (Unofficial) by @Борис
bit.ly/32zqqqq
• Generic System Image (GSI)
cutt.us/GSIgithub
• Official Stock Rom (Laurel_sprout)
c.mi.com/oc/miuidownload/detail?device=1900372
• Coming.. .
✓Note : Flashing method doesn't provide here.
Click to expand...
Click to collapse
Anyone can explain miui 11 flashing method and bugs
pattanirijukvk said:
Anyone can explain miui 11 flashing method and bugs
Click to expand...
Click to collapse
method: flashing guide is given to .7z file..just extract it
bug : no fod & brightness issue
bug sound for me,sound is choppy.
How do I flash this please? I'm new to this phone.
MIUI 11 is Q??
Rajendran Rasa said:
MIUI 11 is Q??[/QUOTE
it's Pie, without many features
Click to expand...
Click to collapse
Barbiox Dogg said:
How do I flash this please? I'm new to this phone.
Click to expand...
Click to collapse
download file there you find instructions.. or go to YouTube. you will find tutorial about it ?
MIUI installing video tutorial (Hindi) :
https://youtu.be/pwvNTYApX2M
gborfitz said:
Never had a Xiaomi device and i want to buy one. I like mi a3 because AMOLED panel and hardware but want to try MIUI as well.
So, about this:
http://c.mi.com/oc/miuidownload/detail?device=1900372
This is official MIUI for mi a3? There's no major bugs in this one then? Can I expect official MIUI 11?
Thanks in advance guys. I'm new with Xiaomi and want to know what you think.
Click to expand...
Click to collapse
The link you commented is redirecting to Mi Community Downloads site but it doesnt mean that the ROM is MIUI. As you see, it says Android One - so definitely the ROM is stock Android.
Xiaomi never released MIUI for its AndroidOne phones.
Can i flash miui 11 with twrp?