Database Users

[Q] bootloader issues

So a while ago I rooted my phone but messed it up because I uninstalled a few too many system apps. I just dealt with it for a few months since I could still make calls (but not much else). I finally bit the bullet to look into flashing the stock rom again, but to do so it looked like I had to install a custom recovery, but to do that, unlock the bootloader. So I first unlocked the bootloader using motopocalypse (batch file didn't work but apk did), and got the expected BOOTLOADER UNLOCKED message at bootup, with fastboot saying unlocked, code 3. I then tried flashing CWM recovery via Rom Manager, and it seemed successful, but I was unable to boot to it either from the UI of ROM manager or from holding the buttons during bootup, it would just hang for a few more minutes than normal at the BOOTLOADER UNLOCKED screen, then boot up like normal. So I kept reading, found RSDlite, and was able to flash the stock rom, which I downloaded from the internet and the phone boots up fine, but now fastboot says locked, status code 2, and motopocalypse does not unlock it again (either the batch file or the apk), but I still get the BOOTLOADER UNLOCKED message at bootup. So I'm not sure if my bootloader is unlocked or not and if I can proceed with installing CWM recovery again, so i can make a full backup in case I mess something up again.
So how do I reunlock the bootloader, or verify if it's locked or not?

First, CWM and TWRP aren't official for this phone, so you can't use their apps to flash. You'll need to use fastboot, Flashify, or Rashr. Second, you're still unlocked, we've seen this error come from bad flashes. What is the complete text on your FB screen. You should be able to clear this by re-flashing with RSD. What firmware did you attempt to flash?
Sent from my HTC6525LVW using Tapatalk

RikRong said:
First, CWM and TWRP aren't official for this phone, so you can't use their apps to flash. You'll need to use fastboot, Flashify, or Rashr. Second, you're still unlocked, we've seen this error come from bad flashes. What is the complete text on your FB screen. You should be able to clear this by re-flashing with RSD. What firmware did you attempt to flash?
Sent from my HTC6525LVW using Tapatalk
Click to expand...
Click to collapse
FB screen:
Code:
AP Fastboot Flash Mode (S)
10.9B(*) (sha-61146a2, 2014-05-02 00:54:39)
eMMC Info: Size 8GB
Device is LOCKED. Status code: 2
Battery OK
Transfer Mode:
USB connected
Fastboot reason: Reboot to bootloader
usb connected
I've tried reflashing with RSD previously but no change. I could try it once more if you want.
Not entirely sure what you're asking for with the firmware version, but the image I used was for android 4.4.2, version 183.46.10.XT907Verizon.en.US.

modemman11 said:
Device is LOCKED. Status code: 2
Click to expand...
Click to collapse
I think your boot loader is still LOCKED. Mine is showing UNLOCKED. Status code: 3. You cannot flash a custom recovery on a phone with a locked BL. You need to motocalypse again!

To trace the issue from the ground up, if you're just trying to reinstall stock ROM, you should be relying on RSD instead of trying to mess with custom recoveries and BL unlocking. Just flash .10 (not .15) via RSD, root via Towelroot and you can start fresh.
Unlocking your BL is still highly recommended, though, 'cuz it's now or never.
Sent from Google Nexus 4 @ CM11
[WARNING: XDA Premium 4.0.13 lacks Signature function - do not update]

Code 3 as well.
Sent from my XT907 using XDA Free mobile app

rahimali said:
I think your boot loader is still LOCKED. Mine is showing UNLOCKED. Status code: 3. You cannot flash a custom recovery on a phone with a locked BL. You need to motocalypse again!
Click to expand...
Click to collapse
Yes, that's why I'm asking. So I've got one vote for unlocked, one for locked. As I said though, motopocalypse isn't working a 2nd time.
AndyYan said:
To trace the issue from the ground up, if you're just trying to reinstall stock ROM, you should be relying on RSD instead of trying to mess with custom recoveries and BL unlocking. Just flash .10 (not .15) via RSD, root via Towelroot and you can start fresh.
Unlocking your BL is still highly recommended, though, 'cuz it's now or never.
Click to expand...
Click to collapse
I would like to flash custom ROMs later down the road, but for now I just want to get the stock stuff going.
On a side note, the version of the image I downloaded was 183.x.x, but my mother, who has the same phone, purchased at the same time, and has never rooted it or anything, has version 182.something, and that is also the version I had before I started messing with the bootloader/recovery stuff. The two versions were released at the same time, but I don't know what determines which version you got if you just did OTA updates, or if it even matters. Speaking of OTA updates, the version I downloaded is prompting me to do an OTA update now to another 183.x.x version. I wonder if I'd be able to grab the 182.x.x ROM from my mom's phone without rooting it via fastboot or something.

The 182/183 does not matter regarding root/boot loader unlock its the .10/.15 that matters do not take the .15 without unlocking your boot loader....
We cannot teach people anything; we can only help them discover it within themselves.

So no other thoughts? What would happen if I flashed a custom rom/recovery with a locked bootloader? I tried flashing the ROM again and fb still says locked, code 2, and motopocalypse still doesn't do anything like it did the first time.

modemman11 said:
What would happen if I flashed a custom rom/recovery with a locked bootloader?
Click to expand...
Click to collapse
It won't let you flash a custom recovery. This is the difference between locked and unlocked.
modemman11 said:
So how do I reunlock the bootloader, or verify if it's locked or not?
Click to expand...
Click to collapse
If your bootloader is relocked for some reasons, try unlocking it again with
Code:
fastboot oem unlock

lem22 said:
It won't let you flash a custom recovery. This is the difference between locked and unlocked.
Click to expand...
Click to collapse
I guess what I'm asking is, will it let me flash it but then the phone won't work or will give an error on boot, or perhaps brick my phone? Or will it just not flash in the first place? Because if it's the latter, then I can just try to flash a custom ROM/recovery and if it works then I know it's unlocked.
If your bootloader is relocked for some reasons, try unlocking it again with
Code:
fastboot oem unlock
Click to expand...
Click to collapse
Code:
D:\adt-bundle-windows-x86-20140702\sdk\platform-tools>fastboot oem unlock
...
(bootloader) fastboot oem unlock [ unlock code ]
OKAY [ 0.031s]
finished. total time: 0.031s
Still locked code 2 though. Looks like it wants an unlock code from Motorola's website, I tried following the steps to get the code but it says I'm not eligible for bootloader unlock. So unless there's another way to get the unlock code...

modemman11 said:
I guess what I'm asking is, will it let me flash it but then the phone won't work or will give an error on boot, or perhaps brick my phone? Or will it just not flash in the first place? Because if it's the latter, then I can just try to flash a custom ROM/recovery and if it works then I know it's unlocked.
Click to expand...
Click to collapse
A "Code 0" locked device would refuse flashing an unofficial or older recovery. I have no idea about Code 2 though.

From what I was able to locate status code 2 indicates that the bootloader has been unlocked and relocked like by doing the whole "fastboot oem unlock unlock code" then the "fastboot oem lock" ... I'll look more into it but from what little I read it looks like it can not be unlocked again with out the Motorola unlock code...
We cannot teach people anything; we can only help them discover it within themselves.

ezknives said:
From what I was able to locate status code 2 indicates that the bootloader has been unlocked and relocked like by doing the whole "fastboot oem unlock unlock code" then the "fastboot oem lock" ... I'll look more into it but from what little I read it looks like it can not be unlocked again with out the Motorola unlock code...
We cannot teach people anything; we can only help them discover it within themselves.
Click to expand...
Click to collapse
Same here, I can see what it means but cannot find any way to get back to code 3 other than using the unlock code from Motorola, which I am unable to obtain because it says I am not eligible. Surprising that someone hasn't cracked the unlock code yet or made a keygen, people are so eager to do it with pirated computer software before the software is even released.

I've read of someone getting locked status code 2 b4 from flashing an older gpt with rsd (if I remember correctly) I think all that was required to fix it and get unlocked again was to flash the latest gpt. Very important..... Are you sure when you were unlocked you didn't ota update to .15? Because flashing .10 gpt while on .15 may be what caused your false relock

Nope, no OTA update to .15. The ZIP I have of the rom does include the gpt.bin file with the same timestamp as all the other files. I suppose I could try reflashing the whole rom once again later...

Hmm strange, I went to find the old thread I read about the gpt relock issue but it's not exactly the same as your situation.
http://forum.xda-developers.com/showthread.php?p=51436123
Until now I didn't think relock was possible due to the way unlocking works. It's a physical change, a qfuse was blown when the motopocalypse apk was run the first time. It can't be unblown lol. Wish I knew what went wrong here.

Droid Turbo XT1254 Marshmallow->Lollipop downgrade (unlocking bootloader)COMING SOON?

Droid Turbo XT1254 Marshmallow->Lollipop downgrade (unlocking bootloader)COMING SOON?
*this is new thread because I started last as Q&A by mistake so first 2 pages may look off with posts and answers.
DOWNGRADING EXPERIMENT TOPIC
So as you may know , after upgrading to Marshmallow OTA, on locked bootloader there won't be any option to unlock bootloader (ever as some people say) , sunshine officially doens't support Marshmallow. The only option is to downgrade which again isn't possible on locked BL..
Or is it ?
Introduction - skip to DOWNGRADE
First of all I'm not an programmer , but have some experience with locked down motorola's bl's , firmware's ,downgrades and so on..
I'm sure when somebody says impossible, it doesn't really mean impossible, but rather not worthy to some. So in my case I bought the phone few days ago, wasn't fully up to date with infos on unlocking BL so didn't check FW version when buying , just after I checked and phone was updated on MM 1-2 days before buying it. On not unlockable BL phone will become useless to me very soon, while unlocked I would plan to have it for long period of time. It goes in Verzion's favour for me to ditch the phone and buy a new one except I'm not in USA , there are no Verzion services in my country and if there were I would never ever buy (again) anything from Verzion. Well I lived in Japan , and there is network Softbank which is well.. Imagine Verizon but on steroids when it comes to tying people down, locked bootloaders and software, insane fee's and so on.. Well that Softbank bough Verizon some time ago .. I was avoiding them at all cost, but on to the topic now.
DOWNGRADE - fastboot
I would like to invite everybody who is interested in this and who can help to participate in this. Every programmer that has time and can contribute would be greatly appreciated! In return I'm willing to sacrifice my phone and my time , even paying some reasonable donations.
While experimenting in the end I was able to flash all bootloader files from various different versions including all partitions related to it which gets upgraded. Even managed to flash XT1250 MM bootloader. Bootloader version DOES change in bootloader / fastboot ,But it doesn't mean ANYTHING. While downgrading , something else, possibly other parts of bootloader obviously search for match and there is more to it than simple bootloader , more experienced , chime on in here! SElinux enforcing? Verity?
(see attachments)
SU4TL-49 bootloader.img to motoboot flash - Successfully
SU4TL-49 manually flashing 1 by 1:
tz.mbn -[/B] Successfully
SBL1.mbn (bootloader) - [/B] Successfully
sdi.mbn - [/B] Successfully
fsg.mbn to mdm1m9kefs3 - [/B] Successfully
rpm.mbn - [/B] Successfully
emmc_appsboot.mbn to aboot - [/B] Successfully
gpt.bin to "partition" , it's the partitions info partition, people say it can't be downgraded or flashed cross versions. After some experimenting mfastboot failed but fastboot succeded, on some versions mfastboot worked - [/B] Successfully
What I can't get to downgrade / cross flash no mather which bootloader and combinations of firmware im on :
boot.img
recovery.img
system,img (sparse_chunk files)
I will go deeper, but hope that new full firmware SBF will be released soon in case of brick. Verzion is slow. I'm making my own full 6.0.1 xml.zip based on full flashable zip's , repacked system.img sparsechunks, rewrited the script but can't get to flash system files due to invalid signed image. Any help with that? It would also help already bricked guys because who knows when'll Verzion release it..
Downgrade OTA way , stock Android Recovery
While stock android recovery is pretty much useless, it can do software upgrades OTA on a fully stock system , which we on locked bootloaders and MM have.
In my opinion , the way is to trick stock recovery into thinking it's flashing ota, and that whole envieroment is like recovery is expecting it while it's actually flashing downgraded version full / close to full firmware in combination with you flashing some partitions manually through fastboot. OTA's contain only "patch" and just replaces files which get changed on new SW. Or even maybe reverse OTA downgrade?
I've made my own update.zip and signed it , but so far get footer size is wrong error so can't flash it .. Need more help here too..

That looks promising!
Marshmallow feels slower than lollipop for me and I wish I could downgrade but I just can't!
I am looking forward to see what you can do about this issue
Good luck bro!

sorry for my mistake, I do not intend to comment here
@EjđiSixo
How to remove the "signed" of system image or bypass it? Fastboot or RSD are stuck at flashing system image. Does this "sign" relate to boot, recovery, partition? Or it's simply the "sign" to prevent downgrade???
I've never succeeded with partition downgrade...
---------- Post added at 10:29 PM ---------- Previous post was at 10:19 PM ----------
when I was flashing the only system.img (3GB), it said that "wrong at header magi". But after a bit time, fastboot separated the file and began to flash. But still failed because of signed image.
I've tried to remove the code from updater-script but it could not write files to system

Not out yet!

Thanks! I think if we all try , we can do it ! For now main focus is downgrading anyhow, even to half working Lollipop just in the purpose of unlocking bootloader with sunshine.
@mr_5kool
Feel free to comment and ask / suggest, thats what this topic is for!
Unforutenately thats the part I haven't yet figured out myself. It is a " permissions" to prevent the downgrade , bootloader and possibly something else checks current version / keys / properly signed image and then flashes. With other bootloader I'm still not able to flash it because it's obviously locked. Motorola probably signs their images differently.
You can't flash 3GB image because when flashing, phone recieve's partition first to ram so max download size is set to 255mb per file. You have to repack system.img to sparse chunks. But you don't have to bother with it , I already repacked system.img which I found at fully stock flashable MCG24.251-5 . It again failed due to invalid signed image . If we could figure out what is exactly signed and how , that would open a lot more possibilities. Possibly even flashing prerooted roms on locked bootloader. There are more possibilities , who knows..
Currently the only thing notices downgrade when flashing is recovery. In bootloader log says I tried to downgrade. Even with downgraded bootloader (kind of, there is sbl2 and sbl3 but they don't get upgraded )

Anyway, I tried something just for the "gags" . Flashed all partitions of XT1250 bootloader. Got to Motorola's site, posted "unlock bootloader data". It returned it's not unlockable of course.. The first sequence of numbers in data is your imei , it starts with 99 and it's verzion's specific imei.
My theory is that motorola ties unlock bootloader data to every phone and imei and stores it in database ( please confirm) . So even with moto maxx bootloader I can't unlock because :
1 it reads my verzion imei
2 it doesn't find alltogether data in the database..
I don't know what are other numbers in the data you get from fastboot, possibly some serial numbers and so on, haven't really checked it .. That's why i think this method is not possible at all for now. Manipulating that data in your phone and running it through motorola's site knowing that exact same code works for some device might be possible, but I think there is really way too much impossible messing involved. If somebody can share more about this?

lol
http://forum.xda-developers.com/dro...ficial-marshmallow-build-mcg24-t3512813/page2
I've renamed it like suggested in the post #11
Download link is at 1st page. It's just a OTA.

Yes I just renamed it.
IT DOESN'T WORK WITH ADB AND YOU CAN'T FLASH IT AGAIN THROUGH RECOVERY. ITS OTA.

EDIT: The post that I was responding to has been removed.

The method to downgrade from Lollipop to Kitkat is the same with what I've done. It may be possible. Some said that "impossible to downgrade with locked bootloader on vrz". So the system image may be signed with bootloader (or imei, serial or something else, god know).
The unlock method of Sunshine takes place in Trustzone (sbl2). They cannot get unlock code.

You succesfully downgraded LL to KK on droid? There is partition for trust zone alone "tz.mbn" , downgradable without any problem. I only see sbl1 get's upgraded on droid turbo , never saw in any firmware sbl2 or 3 yet.. So I'm little confused.. I remember I saw some PDF regarding that..

Yes, successfully downgraded 5.1 to 4.4.4 on Droid Turbo but with unlocked bootloader. I helped this guy.
http://forum.xda-developers.com/droid-turbo/help/solved-problem-downgrade-install-ota-t3497791
http://forum.xda-developers.com/droid-turbo/help/how-to-downgrade-lollipop-5-1-to-kitkat-t3494459

Finally managed to *Brick my devices while trying to make latest sbf firmware (what an irony ) because used some of files from that stupid OTA . Tried flashing all possible firmware I have but it doesn't fix it so system got corrupted probably and for now didn't succed flashing any of the available systems. Flashing MM recovery doesn't help. It's a " recovery loop".
Basically phone starts , vibrates , goes into recovery, it says "erasing" , it does the factory reset then restarts and over and over again erasing restarting loop.
I'll continue exploring downgrade options but top priority now is making working marshmallow sbf or waiting for stupid Verzion to release it already. Just checked with SUA and it still doesn't show repair so firmware isn't available still.
Biggest problem is signed system images which are probably signed by RSA and I need help with that..

I have same problem erasing

Can't flash SU4TL gpt.bin anymore , so success was definitely connected to experiment and steps I did so I'll investigate more.

@EjđiSixo
I have never tried before. My Moto X2013 failed to downgrade from LL to KK, too. So, it's the common problem of Verizon Motorola Devices.
If you have problem with "erasing", just enter recovery by "hold power button for a while then fast press volume up button". Phone will enter recovery and do the factory reset. But when rebooting the system, "erasing" appear again.
If partition is dead, flash the higher version, commonly gpt and tz.
PS: still waiting for the official xml firmware

ChazzMatt said:
Yes, successfully downgraded 5.1 to 4.4.4 on Droid Turbo but with unlocked bootloader. I helped this guy.
http://forum.xda-developers.com/droid-turbo/help/solved-problem-downgrade-install-ota-t3497791
http://forum.xda-developers.com/droid-turbo/help/how-to-downgrade-lollipop-5-1-to-kitkat-t3494459
side note, I hate this Q&A format. Not sure why XDA even has it. You can't even format URL links correctly.
Click to expand...
Click to collapse
mr_5kool said:
@EjđiSixo
I have never tried before. My Moto X2013 failed to downgrade from LL to KK, too. So, it's the common problem of Verizon Motorola Devices.
If you have problem with "erasing", just enter recovery by "hold power button for a while then fast press volume up button". Phone will enter recovery and do the factory reset. But when rebooting the system, "erasing" appear again.
If partition is dead, flash the higher version, commonly gpt and tz.
PS: still waiting for the official xml firmware
Click to expand...
Click to collapse
I wonder if there is any way to force Verizon to release firmware. This is really low of the lowest, it says 1 week after OTA , now it's almost 1 month. Until somebody forces them , it can be months as far as they are considered. No help from developers / programmers either on any of 2 subjects so don't see my method of full MM SBF working.

god know
:v

ChazzMatt said:
Yes, successfully downgraded 5.1 to 4.4.4 on Droid Turbo but with unlocked bootloader. I helped this guy.
http://forum.xda-developers.com/droid-turbo/help/solved-problem-downgrade-install-ota-t3497791
http://forum.xda-developers.com/droid-turbo/help/how-to-downgrade-lollipop-5-1-to-kitkat-t3494459
Click to expand...
Click to collapse
Exactly brother .
I solved my problem .
I can downgrade from Marshmallow to lollipop is very easy for my ..
But first step is unlocked bootloader from lollipop..
Sent from my XT1254 using XDA Free mobile app

Yeah people , we all know everything can be done with unlocked bootloader. It's a GOD mode. Nothing strange about downgrading with unlocked BL. This topic is for people stuck on locked BL like myself to try to odowngrade on lollipop only in purpose of UNLOCKING BL. So let's for now focus on locked BL's.

Bricked Axon 7 after re-locking bootloader

Long story short. I had an Axon 7 A2017 B11 which I updated to B13. I was able to unlock the bootloader, root the phone then flash a custom rom Z.A.D.Mix7_v0.3. I was having fun with the phone but I did something very stupid when I realised I could not use Android pay due to unlocked boot loader. Without doing enough research, I went to fastboot and did a fastboot oem lock. The command was successful but I could no longer boot into the system or recovery or fastboot. I tried MiFlash with B07 which was posted in this forum, but it did not work, came back an error of bad format. Then I used axon7tool to flash TWRP 3.0.2 and the boot.img which I extracted from B13. I am now able to boot into TWRP and fastboot. But I still do not have a working system. I tried fastboot oem unlock, it does not let me do it. I flash ZAD Mix7 again but once I flash that it does not boot anymore. I am now really stuck. What should I do to go back to stock then start everything again. Thanks a lot for the help.

I understand your device doesn't boot into system anymore, but can adb on your pc detect it at all? If so, you can try following all steps after "B)" in my tutorial. I think your aboot img and fbop partition are messed up. If you can use adb to replace the files in aboot and fbop with files that allow the fastboot oem unlock command to be executed, it should be unlockable again. After that, custom ROMs should boot.

Stock bootloader
Controllerboy said:
If you can use adb to replace the files in aboot and fbop with files that allow the fastboot oem unlock command to be executed, it should be unlockable again. After that, custom ROMs should boot.
Click to expand...
Click to collapse
I'm having a similar issue. Although my phone boots to stock rom I seem to have messed up my bootloader. I had TWRP and unlocked bootloader. I, similarly, locked the bootloader and things seemed to be fine. After attempting to install Nougat received from OTA I realized my bootloader is corrupted. When I hold the power and volume up the phone seems to just turn off (or go to EDL mode? I'm not sure) I can always just hold power and it'll boot up normally. Is there a way to get the stock bootloader to work and keep it locked?

I also bricked my A7 after relocking my bootloader. I used tenfar's tool to make TWRP my boot.img, then flashed ZTE's stock B20 image. Here's the thread where I found the file links.
From there I updated all the way up to the OTA Nougat, but I suppose you can decide where you want to go after it's unbricked. Hope this helps.

Why are so many people relocking bl? Regardless, always take an ota before locking to ensure you are completely shock.

Stock bootloader
lafester said:
Why are so many people relocking bl? Regardless, always take an ota before locking to ensure you are completely shock.
Click to expand...
Click to collapse
Don't you have to be running a locked bootloader in order to be able to install OTAs?

aabnamak said:
Don't you have to be running a locked bootloader in order to be able to install OTAs?
Click to expand...
Click to collapse
Of course not.

aabnamak said:
Don't you have to be running a locked bootloader in order to be able to install OTAs?
Click to expand...
Click to collapse
No, you do not. I thought that was the case at first as well, but I was mistaken. You do, however, need the stock recovery and an untouched system partition.

My problem is that I don't seem to have a recovery at all. I realized once the ZTE logo pops up I can hold down both volume keys and get to the bootloader. The bootloader is locked but does not display a bootloader version or basedband version. I tried the tenfar tool (axon7root.exe) and now my phone doesn't boot into the system either. I really need help...

Just an update to everyone that helped.
I finally managed to fix it.
I used axon7tool to flash a signed TWRP, so that i can boot into TWRP. The signed TWRP is the only way to make it work. Then I downloaded the A2017 B11 from this thread
https://forum.xda-developers.com/axon-7/development/rom-guide-updates-to-stock-files-via-t3469484
There are two zip files. The boot stack and the rom. Because it is a stock rom, I can boot into the system. The next thing I did was to enable the developer option and turn back on the option to allow OEM unlock.
I went back to TWRP. boot into the fastboot screen. Then I simply typed in 'fastboot oem unlock'.
I went back to TWRP, which says can't read encrypted device. I formated everything. mount the USB then flash the custom rom again.
Hola, phone fixed. Made me sweat for the whole day.

deleted...forgot I had a micro sd card. Flashed stock update from the card and it worked. Phew!

Need to Re-Lock Bootloader on my friends XT1572

So the only thing that has been done with this phone, is that the bootloader has been unlocked, officially with a code from Motorola. No custom recovery, ROM, or anything were installed on it.
I need to re-lock the bootloader so he can return it to warranty as his screen sometimes goes crazy and starts clicking everywhere. So I just download the latest firmware for Vodafone Australia, which I believe is:
XT1572_CLARK_RETASIA_6.0_MPHS24.49-20-8_cid7_subsidy-DEFAULT_CFC.xml
from:
https://firmware.center/firmware/Motorola/Moto%20X%20Style/Stock/XT1572/
And then follow the commands from this thread in the OP for the XT1575 (*should be the same codes, right?*).
https://forum.xda-developers.com/moto-x-style/general/guide-return-to-stock-relock-bootloader-t3489110
Also one final note, is the firmware I posted above the latest one for vodafone Australia? Just for confirmation, I am not sure, but according to this guide, it belongs to vodafone Australia:
https://forum.xda-developers.com/moto-x-style/general/australian-xt1572-guide-to-restore-t3292794

Qustion is what firmware on phone do you have?
Relock is possible by flashing the same or upper version only. @Blackfyre

dzidexx said:
Qustion is what firmware on phone do you have?
Relock is possible by flashing the same or upper version only. @Blackfyre
Click to expand...
Click to collapse
In the Bootloader it says:
Baseband: M8992_1255331.29.01.88.07R CLARK_APAC_CUST
Product/Variant: clark XT1572 32GB PC3
In the Phone Settings:
Build Number: NPH25.200-15
Any way to find out exactly if that's the same firmware as in the OP?
EDIT: His phone is running Nougat, I can't find a Nougat ROM for Clark ASIA or APAC (at all) from the link of firmwares above.

Blackfyre said:
In the Bootloader it says:
Baseband: M8992_1255331.29.01.88.07R CLARK_APAC_CUST
Product/Variant: clark XT1572 32GB PC3
In the Phone Settings:
Build Number: NPH25.200-15
Any way to find out exactly if that's the same firmware as in the OP?
EDIT: His phone is running Nougat, I can't find a Nougat ROM for Clark ASIA or APAC (at all) from the link of firmwares above.
Click to expand...
Click to collapse
There is no Nougat factory firmware image available, or even the "latest" Marshmallow version. Sorry, but without those it is no possible to lock the booloader. In order to lock the bootloader, you must flash a complete, signed image that is the same or a newer version than what you have.
Remember that relocking the bootloader will NOT remove the Unlocked Bootloader boot splash screen, nor will it hide the device has ever been unlocked (it is still plainly visibile on the bootloader screen and in a getvar all).
TBH, I have doubts we will ever see more factory firmware images... relocking the bootloader will probably never be possible.

@Blackfyre
This is Nougat, no flashable firmware.
Flash modified logo.bin and try warranty repair.

@acejavelin and @dzidexx
Thank you for the replies. I have a few questions.
If I root the device, can I install an old ROM on it, then update to the latest firmware available that is above, then lock OEM?
Would doing that result in Software = Modified? Because currently it's still Unmodified.
Flashing the modified logo.bin you mentioned above I am guessing will remove that warning that shows up at boot stating that the bootloader has been unlocked. Would flashing this .bin file result in Software = Modified or not?
And if not, then where can I find this modified logo.bin?
Thank you guys again for your help and replies.

https://forum.xda-developers.com/mo...e-unlocked-bootloader-warning-t3201141/page22
fastboot flash logo NameOfFile.bin
If after flashing still will be unmodified you can try relock:
fastboot oem lock begin
fastboot erase userdata
fastboot erase cache
fastboot oem lock @Blackfyre

dzidexx said:
https://forum.xda-developers.com/mo...e-unlocked-bootloader-warning-t3201141/page22
fastboot flash logo NameOfFile.bin
If after flashing still will be unmodified you can try relock:
fastboot oem lock begin
fastboot erase userdata
fastboot erase cache
fastboot oem lock @Blackfyre
Click to expand...
Click to collapse
Does that work though without flashing full firmware images?

quakeaz said:
Does that work though without flashing full firmware images?
Click to expand...
Click to collapse
No, you must flash a full, signed image... In some newer Moto devices you can get by with flashing only the signed system sparce_chunks and wiping data, in 3rd gen and older devices flashing a full signed image, even if already stock, is required.

acejavelin said:
No, you must flash a full, signed image... In some newer Moto devices you can get by with flashing only the signed system sparce_chunks and wiping data, in 3rd gen and older devices flashing a full signed image, even if already stock, is required.
Click to expand...
Click to collapse
Previous post - It was only my hope.
In Europe, Moto/Lenovo can not refuse to repair the components for two years.

dzidexx said:
Previous post - It was only my hope.
In Europe, Moto/Lenovo can not refuse to repair the components for two years.
Click to expand...
Click to collapse
Eh... Yeah, they can and do, often saying that what was done while unlocked is the cause of the problem... And then you have to fight it, by the time it's all said and done many people just give up as the process can take many months.

Hard brick

next ... After unlocking the bootloader of my g4 plus bike, I made the installation of the rom and an update arrived via ota ... I placed to make the installation and after made the cell phone hung up and did not call any more ... then I did the blankflash and the mobile came back in fastboot mode with the boot blocked again, now I can not install any rom and nor unblock the boot by not having the option oem unlock checked ... my question is the following have some way to enable the option unlock boot without starting the system, by adb or something, or do the installation of some rom with the boot blocked? Thank you very much in advance

Which ROM did you flash onto your device?
As far as I understand, you cannot enable the OEM unlocking option without booting to system, and as your bootloader is set to OEM_locked by the blankflash, you need to flash the stock ROM firmware to get your system working.
I'd suggest looking into flashing the latest stock ROM firmware, follow this unbricking guide here: https://forum.xda-developers.com/moto-g4-plus/how-to/moto-g4-plus-hardbrick-solved-guide-t3657761
If that doesn't work, then you may have to wait for a newer firmware or submit your device for an expensive service repair.
For future reference, if you did flash an older stock ROM firmware, please delete that and only flash stock ROM firmware as new or newer than your bootloader. If you do want to flash older stock ROM firmware, do not use OTA updates please. Old OTA updates corrupt your bootloader and thus lead to a hard brick.