Related
Hi all,
This is my first post here, I'll try to include everything but please let me know if I am missing any info. I'm using Windows 10, my phone is using Stock ROM 6.0.1, carrier unlocked from Telus to Rogers but bootloader shows device is Locked.
TLDR: I'm trying to recover the photos from my soft-bricked phone before doing a factory reset. I've tried to manually flash the firmware with fastboot by following the steps in service.xml, but the commands all appear to return OKAY without errors but there's no change in the phone's behaviour.
More Info: I've spent the last 2 days reading up on here and elsewhere online to learn as much as I can. I am honestly not sure what caused it the soft-brick. I was using my phone normally yesterday morning when it froze while browsing Facebook, so I tried to power it down, but I got caught in a bootloop and it wouldn't go past the logo screen. It's part of my morning routine to run updates, and I often (though not yesterday) transfer files to/from the phone through a USB cable, so could it be an internal memory problem? Other possibilities, while I was careful ultimately I did download an apk for Pokemon Go before it was released in my country, and I did also download a battery saving app, so there's risks from both of those but the timing seems wrong...
I can get into bootloader and recovery mode, but not factory mode. Wiping the cache partition did not help. The only way to power the phone down is from bootloader, otherwise the phone goes straight to the logo screen.
I've installed ADB/Fastboot using the 15 Second ADB Installer here, and believe I have all of the correct drivers from the WinDroid install. However I did not enable USB Debugging before this happened, so the only way I can get ADB to see the devices is to go to "Apply update from ADB" in recovery mode, but running "adb devices" brings the phone up as sideload. If I'm in bootloader, "fastboot devices" sees it, "adb devices" comes back empty.
I used the file XT1563_LUX_RETCA-ROGERS_6.0.1_MPD24.107-52_cid14_subsidy-RGRCA_CFC.xml.zip from the File Factory folder, and it looks right according to the software version in the .xml files, but I'm still new to this and I'm not sure if my best guess is educated enough.
In general I'm not too squeamish about voiding the warranty and don't care about losing my apps, it's the photos that I really do not want to lose (shame on me for not backing those up!). I'm wondering if there's a way to get my photos back before unlocking or doing a factory reset, but if there's a reliable recovery software I can use after the fact I may have to bite the bullet.
TIA for any help.
An update. I chose to wipe user data (NOT including personalized content), the phone rebooted but is looking different from before. Which in and of itself is alright, but makes me wonder if I flashed the correct firmware...?
During the setup process, I was given the option to restore data from 3 days ago, which was when the soft-brick occurred. I chose to recover most of my apps, however I can't see any photos. I tried Recuva but it could not see anything, I'll be trying trying the Wondershare Dr. Fone Android Recovery program and hope it finds the photos.
Hello,
i have a problem with my 1 week old yotaphone and hope you guys can help me to solve.
Let me say, this is my first android device. After a long time using iphones i saw this 2-displays concept and wanted to give it a try.
But now my problem and the way to:
The phone was brand new and first of all i charged it for a wohle night.
After that i put in the sim-card and started the phone and walked through the start-procedure with WLAN, Googleaccount etc.
Then the phone told me about an update and i started it over WLAN.
The phone was downloading, rebooting and shows me a white window "updating x of 127(?) Apps".
Somewhere in the middel the phone rebooted again and now its in a bootloop.
What is possible with the phone right now.
I can start the phone wit the bootloop (powerred byAndroid, then restart)
I can use "Power + Vol-" to bring it into downloading mode
When i use "Power + Vol+" nothing happend.
When i use "Vol+ + Vol-" nothing happend.
The akku of the phone is empty now and it only works with usb or power unit connected.
In bootloop or downloading mode it is not charging.
What i tried.
What i try:
I read many topics with bricked / bootlooped yotphones and how to flash or cache whipping.
i connected the phone to my pc and used yotoflasher with many different firmwares.
I used fastboot:
- flashed the system.ing with differnet sizes.
- tried different custom recovery.img from different threads here and from other sites.
Even a complete new image, moddified RU img doesn`t help.
The phone stays in bootloop.
Yes, it`s a warranty case, but before i start to strech my nerves by handling with the dealer and shipping
this phone back to china i will try everything else and hope you can help me out of this situation.
Thanks a lot
easyxx said:
Hello,
i have a problem with my 1 week old yotaphone and hope you guys can help me to solve.
Let me say, this is my first android device. After a long time using iphones i saw this 2-displays concept and wanted to give it a try.
But now my problem and the way to:
The phone was brand new and first of all i charged it for a wohle night.
After that i put in the sim-card and started the phone and walked through the start-procedure with WLAN, Googleaccount etc.
Then the phone told me about an update and i started it over WLAN.
The phone was downloading, rebooting and shows me a white window "updating x of 127(?) Apps".
Somewhere in the middel the phone rebooted again and now its in a bootloop.
What is possible with the phone right now.
I can start the phone wit the bootloop (powerred byAndroid, then restart)
I can use "Power + Vol-" to bring it into downloading mode
When i use "Power + Vol+" nothing happend.
When i use "Vol+ + Vol-" nothing happend.
The akku of the phone is empty now and it only works with usb or power unit connected.
In bootloop or downloading mode it is not charging.
What i tried.
What i try:
I read many topics with bricked / bootlooped yotphones and how to flash or cache whipping.
i connected the phone to my pc and used yotoflasher with many different firmwares.
I used fastboot:
- flashed the system.ing with differnet sizes.
- tried different custom recovery.img from different threads here and from other sites.
Even a complete new image, moddified RU img doesn`t help.
The phone stays in bootloop.
Yes, it`s a warranty case, but before i start to strech my nerves by handling with the dealer and shipping
this phone back to china i will try everything else and hope you can help me out of this situation.
Thanks a lot
Click to expand...
Click to collapse
Mine too,stuck in bootloop. I also tried the fastboot and it said waiting device.
kophyo07 said:
Mine too,stuck in bootloop. I also tried the fastboot and it said waiting device.
Click to expand...
Click to collapse
If your phone displays Downloading... and fastboot keeps saying waiting for device then there is something wrong with the installed ADB driver. Check some of the posts in this forum like this one on how to fix this. http://forum.xda-developers.com/yotaphone-one/help/yotaphone-2-yd-206-china-flash-firmware-t3306797/post69311402#post69311402
Strange that you had an OTA (Over The Air update). You didn't do anything between the SIM/Google registration and OTA ?
Normally there are no OTAs allowed on yd206 phones bought from China/HK , where did you buy it ? Chinese retailers have their own firmware that they put on phones , for me , maybe you had bad firmware installed.
The warranty of your phone is voided if you flash yotaphones bought from China and HK .
When you use yotaflasher do you get error message or "waiting for device" ?
To flash the Yotaphone , it should be in developer mode , but you couldn't put it in this mode because it first did the OTA that started your bootloop. Android apps are updated like that ("installing x of 127") when it gets updated to lollipop. Normally the OTA should have worked OK. Did you allow enough time at the Yotaphone logo after the first reboot ? It stays on this logo for 5 minutes before starting. I made this mistake.
The OTA started just after you set up Google etc ?
If so, normal yotaflashing will never work, but at least you havent broken the warranty . The thing we need to know is what exactly happened when you tried to flash , what errors messages appeared ?
If you did not put the phone in developer mode, then you cannot easily flash the phone, so your best possibility is to return the phone. Normally you can contact the seller by chat or email . Some are very good in exchanging.
It IS possible to flash your phone using fastboot, but I would not personally attempt it and you would lose your warranty . You need rootkits, SDK toolkits, universal drivers and images. Google "bootloop without USB debugging".
When I flashed my yd206 , (after many attempts) I flashed my yd206 to yd201 Russian KitKat ROM first and then did an OTA to lollipop.
Hi folks,
So, after little usage due to instability caused by the Lollipop upgrade I hadn't used the TN7 in a while. Yesterday I thought I'd have a go at reconditioning it.
Background: The bootloader has been unlocked, recovery was TWRP, I'd flashed and reflashed stock ROMs of KitKat and Lollipop several times previously. The main problem in Lollipop was that whilst the SD card files were showing up fine in FS Explorer, I couldn't see any of my files or folders when looking at local storage. Also, Google Play Services refused to update (or install using an APK).
Yesterday I grabbed the factory ROM from the nVidia site to do a full factory install and reset. I followed the instructions, flashing the recovery, boot, system, userdata, staging blob and dtb in that order. I then rebooted and...nothing. No power (or so it appears), no boot screen, no ability to get back into the bootloader, nada, zilch. When I read back through the flash commands I noticed that the final part of flashing the system image failed, which could well be the cause - I should have paid more attention.
I've searched all over and tried multiple options to get the TN7 to boot or show some signs of life. I don't even get an LED showing when plugged into a wall socket to charge.
The device doesn't show in fastboot or adb on the Mac. I did however get a small sign of life from Windows. If I hold down the power button for around 10 secs and let go, I can hear the Windows chime of a device connecting, immediately followed by a disconnect sound, the Device Manager updates but shows nothing new.
So my question is: have I completely screwed the pooch, or is there something that can be done to resurrect it?
Cheers for reading,
Gray
Evil Penguin said:
Hi folks,
So, after little usage due to instability caused by the Lollipop upgrade I hadn't used the TN7 in a while. Yesterday I thought I'd have a go at reconditioning it.
Background: The bootloader has been unlocked, recovery was TWRP, I'd flashed and reflashed stock ROMs of KitKat and Lollipop several times previously. The main problem in Lollipop was that whilst the SD card files were showing up fine in FS Explorer, I couldn't see any of my files or folders when looking at local storage. Also, Google Play Services refused to update (or install using an APK).
Yesterday I grabbed the factory ROM from the nVidia site to do a full factory install and reset. I followed the instructions, flashing the recovery, boot, system, userdata, staging blob and dtb in that order. I then rebooted and...nothing. No power (or so it appears), no boot screen, no ability to get back into the bootloader, nada, zilch. When I read back through the flash commands I noticed that the final part of flashing the system image failed, which could well be the cause - I should have paid more attention.
I've searched all over and tried multiple options to get the TN7 to boot or show some signs of life. I don't even get an LED showing when plugged into a wall socket to charge.
The device doesn't show in fastboot or adb on the Mac. I did however get a small sign of life from Windows. If I hold down the power button for around 10 secs and let go, I can hear the Windows chime of a device connecting, immediately followed by a disconnect sound, the Device Manager updates but shows nothing new.
So my question is: have I completely screwed the pooch, or is there something that can be done to resurrect it?
Cheers for reading,
Gray
Click to expand...
Click to collapse
Hi,
It can be fixed via apx mode.
Download drivers and switch to apx mode.
Follow instructions http://mobileviandroid.blogspot.in/2015/07/nvidia-tegra-note-7-apx-images.html?m=1
Remember to change your device serial number as mentioned in instructions.
I also faced the same problem as you are facing now. It fixed. If you need any help further just post. God bless. Hope it helps
DJDON1302 said:
Hi,
It can be fixed via apx mode.
Download drivers and switch to apx mode.
Follow instructions http://mobileviandroid.blogspot.in/2015/07/nvidia-tegra-note-7-apx-images.html?m=1
Remember to change your device serial number as mentioned in instructions.
I also faced the same problem as you are facing now. It fixed. If you need any help further just post. God bless. Hope it helps
Click to expand...
Click to collapse
Lol that site ripped my Tutorial! how nice of them, You should of linked the person to https://forum.xda-developers.com/nvidia-tegra-note-7/general/nvidia-tegra-note-7-apx-images-t3149839
Hi all !
I have a Samsung A8 (model SM-A800F) which was working great. I ran Kingo Root to try to install Youtube ad free. The next time I restarted it, it didn't load, and restarted in an endless loop to where "Samsung" logo appears (then restarted again). I booted into System Recovery and chose to reset to factory, but it didn't help. Then I tried flash it using Odin in Download mode. I installed the Windows drivers, downloaded the 6.0.1 firmware for Vietnam (where it was purchased), loaded the file into the AP field, and once verified clicked Start. The progress was frozen when reaching mid-way every time I tried, until it said "an error occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"...
I downloaded Smart Switch and installed in Windows, but the drivers were not able to install correctly, and failed on the component referring to the ID or something... while Modem driver was installed correctly and the phone appeared in Device Manager. Smart Switch didn't recognize my phone and said "unsupported device".
Now I cannot get the phone stay constantly ON, and the screen shuts down and loads in an endless loop, to the "Error occured" screen... When trying to boot to the ODIN Download page, it loads, I press UP for Continue, and then it again shuts down and loads to "Error Occured".
I tried to charge over night but it didn't help. It does the same thing when the phone is connected to the charger...
However it seems that by IMEI it is sill under warranty. I'm not sure if I voided it :/
Here's what the Download mode page says:
ODIN MODE
PRODUCT NAME: SM-A800F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
FAP LOCK: ON
Secure Download: Enabled
KNOX WARRANTY VOID: 0
AP_SWREV: 1
Would appreciate any help, this phone is almost new but now it's dead :/
Your warranty is not voided. Your Knox E-Fuse still intact.
Also this is for S8 not A8 forums.
Paradoxxx said:
Your warranty is not voided. Your Knox E-Fuse still intact.
Also this is for S8 not A8 forums.
Click to expand...
Click to collapse
Thanks,
I just couldn't find any A8 forum, and thought there would be more people here who can help.
Would appreciate any help on this... thanks in advance
wurlitzer99 said:
Thanks,
I just couldn't find any A8 forum, and thought there would be more people here who can help.
Would appreciate any help on this... thanks in advance
Click to expand...
Click to collapse
No worries, your phone is not dead.
Try to find a firmware that correspond to the one you got :
http://updato.com/firmware-archive-select-model?exact=1&q=SM-A800F
and use ODIN : http://dl.sammobile.com/Odin3-v3.12.7.zip
You should be good to go.
EDIT : Also for that error occurred thing, try to be faster than it by starting odin flash before it appears.
Thanks,
The problem is that neither the error nor the Odin page would stay on for more than a few seconds. Once they appear, the screen would go dark after 5-10 seconds and then the "error" page would load again (after being darks for another 10 seconds or so). So I can never have ODIN or Smart Switch connecting to the device (the drivers won't connect in Windows)... making it impossible to upload any firmware.
wurlitzer99 said:
Thanks,
The problem is that neither the error nor the Odin page would stay on for more than a few seconds. Once they appear, the screen would go dark after 5-10 seconds and then the "error" page would load again (after being darks for another 10 seconds or so). So I can never have ODIN or Smart Switch connecting to the device (the drivers won't connect in Windows)... making it impossible to upload any firmware.
Click to expand...
Click to collapse
Could you take a picture of that error ? I've never heard/seen such thing
Hi, thanks for the help !
The error is this:
http://statics1.grupoandroid.com/up...1850.jpg.d2bb2a8b77e4fba5fc6467f3d1547886.jpg
I *think* I have some direction... here's what I did/found:
- I installed Smart Switch on my Mac, and chose "Reinstall Device Driver" from the menu. Then restarted the MAC
- I loaded Smart Switch, and Chose "Emergency Software Recovery and Initialization". Then chose the "Device Initialization" tab
- Added the model number "SM-A800F" and the device's serial number (which are physically written on my device).
Smart Switch determined the firmware version to be used for initialization, as:
PDA:QC3 / PHONEG3 / CSCH4(XXV)
- Smart Switch asked to:
1. Power the device down
2. Load recovery mode by pushing Power+Vol Down+Home, then connect the device to the MAC and choose "Continue" to start the initialization...
The problem/s:
My device won't turn on at all, if I do not connect it to either the charger or the MAC (which acts as a supply source?) - which makes me think the battery is fully drained ? i.e when not connected at all, it won't power on.
But when connected to either the charger or MAC, it would bootloop endlessly. i.e it will load the "error" page mentioned above, shut down itself, reload again, shut down and so on.
(I have to mention, that when I first noticed the bootloop, I reset everything to factory settings, cleared cache etc, and it still bootlooped on the Samsung logo).
If when it shuts down during the loop, I push Power+Vol Down+Home, it would boot to ODIN recovery page, where I can push UP for the Download page, but it will still reboot and will again load into the "error" page, which will again reboot endlessly. If I take the charger off the device, it powers off and won't load with any combination of button push.
I also cannot just make it shut down when the charger is connected, using any of the possible button combinations...
I wonder:
- Is there there's a problem which prevents the battery from being charged at all ?
What's strange is that the original problem which made me get into this whole issue, was that is was endlessly booting to the "samsung" logo - but when I booted to System Recovery or Download/ODIN modes, it stopped rebooting endlessly and stayed on... it was also showing the charging indication when powered off... the battery was charging well ever since.
- Why would it bootloop when connected to the charger ? is it possible that the bootloader went bad during my attept to install firmware using ODIN ? I know it always went through the boot.img and recovery.img successfully and only got stuck at about 50% when installing system.img...
I think the current bootloop problem began only once the battery ran out of power. But why wouldn't it charge at all now ??? It's supposed to still charge in this state, isn't it ?
wurlitzer99 said:
Hi, thanks for the help !
The error is this:
http://statics1.grupoandroid.com/up...1850.jpg.d2bb2a8b77e4fba5fc6467f3d1547886.jpg
I *think* I have some direction... here's what I did/found:
- I installed Smart Switch on my Mac, and chose "Reinstall Device Driver" from the menu. Then restarted the MAC
- I loaded Smart Switch, and Chose "Emergency Software Recovery and Initialization". Then chose the "Device Initialization" tab
- Added the model number "SM-A800F" and the device's serial number (which are physically written on my device).
Smart Switch determined the firmware version to be used for initialization, as:
PDA:QC3 / PHONEG3 / CSCH4(XXV)
- Smart Switch asked to:
1. Power the device down
2. Load recovery mode by pushing Power+Vol Down+Home, then connect the device to the MAC and choose "Continue" to start the initialization...
The problem/s:
My device won't turn on at all, if I do not connect it to either the charger or the MAC (which acts as a supply source?) - which makes me think the battery is fully drained ? i.e when not connected at all, it won't power on.
But when connected to either the charger or MAC, it would bootloop endlessly. i.e it will load the "error" page mentioned above, shut down itself, reload again, shut down and so on.
(I have to mention, that when I first noticed the bootloop, I reset everything to factory settings, cleared cache etc, and it still bootlooped on the Samsung logo).
If when it shuts down during the loop, I push Power+Vol Down+Home, it would boot to ODIN recovery page, where I can push UP for the Download page, but it will still reboot and will again load into the "error" page, which will again reboot endlessly. If I take the charger off the device, it powers off and won't load with any combination of button push.
I also cannot just make it shut down when the charger is connected, using any of the possible button combinations...
I wonder:
- Is there there's a problem which prevents the battery from being charged at all ?
What's strange is that the original problem which made me get into this whole issue, was that is was endlessly booting to the "samsung" logo - but when I booted to System Recovery or Download/ODIN modes, it stopped rebooting endlessly and stayed on... it was also showing the charging indication when powered off... the battery was charging well ever since.
- Why would it bootloop when connected to the charger ? is it possible that the bootloader went bad during my attept to install firmware using ODIN ? I know it always went through the boot.img and recovery.img successfully and only got stuck at about 50% when installing system.img...
I think the current bootloop problem began only once the battery ran out of power. But why wouldn't it charge at all now ??? It's supposed to still charge in this state, isn't it ?
Click to expand...
Click to collapse
Hmmm, the thing is, the battery charging process is actually held on some kind of "mini-boot" OS on Samsung I believe, where the phone boots into a certain state, with that said mini-os to display the battery charging info and this kind of things.
My guess is that you *might* have, or more likely your phone did corrupt the flash at some point for x or y reason.
What I'd do is :
Let the phone on a charger a whole night doing its bootlooping thing. And see from there if the battery would charge.
I'd try another computer with Odin just to be sure something is not triggering the reboot process at some point.
And if all the above fails, you still have the warranty, so beside time, you would not be losing any money..
I'm going to write a long post. But I believe it will help a lot of people having a similar problem.
Long story short - problem solved! but it took much of my nerves (and time).
I'll start with the "warranty". The so-called Samsung "warranty" which basically worths nothing!
Calling Samsung international service center, they "informed" me that I must contact Samsung Vietnam, where I bought the device, although I am not there anymore... Needless to say the local dealer in my country refused to take care of this situation, saying Samsung's warranty is regional based, rather than international... which means, only Samsung in the original country where the device was sold in, are responsible for the warranty (and therefore repair!). I had a chat with a Samsung Vietnam representative, who just kept saying "I'm sorry", and refused to let me sent the device out to them for repair! asking me to "bring it to them", although I noted him a few times that I bought it as a tourist and I am not in Vietnam anymore.... Thank you Samsung !! From now on every traveler in the world will know they basically have NO WARRANTY if they buy any Samsung device in a "foreign" country while traveling abroad!
Now for the solution:
I started by letting the device staying connected to the charger overnight, which didn't help. With the OS now installed, I realize that the battery was NOT CHARGED ! it was completely drained, although connected to a charger for long hours... So, know from now on that if your boot data is corrupted, it may cause the device NOT TO CHARGE THE BATTERY at all. Luckily, my desktop PC could use the device while connected to it although the battery was empty, until the problem was sorted out. I did get a crash on my MAC tough (Log said it was USB related), while using Smart Switch, so one option is that it could not supply enough power to the device to keep it keep working at all, or working correctly... So my suggestion is to use a desktop Windows PC in this case, which can potentially provide more power to a device with 0% battery power.
After scratching my head, and considering removing the front panel for replacing the battery (a very risky procedure) I decided to keep on investigating....
I followed a youtube video who suggests that you should install Smart Switch on a PC, choose "reinstall driver" from the menu, restart the PC, then use Emergency Recovery and Initialization, enter the phone model number in the search box (as appearing on the back of the device) , and once it recognizes the model, also to enter its serial number. Here's the video:
https://www.youtube.com/watch?v=1yXQUFrEWg4
This basically brings up a popup message saying Smart Switch detects a compatible firmware for this device, and is about to download and install it. It then asks the user to do the Power+Vol Up+Home push combination trick + pushing UP once the page is loaded in order to "Continue" and bring up the ODIN Download screen, which worked for me if did that as soon as the device shuts down (in the middle of the bootloop). As I couldn't make it load at all with no charger connected, I had it connected to the charger, and once I saw the Smart Switch message asking to do the push combination, I quickly connected it to the computer using another cable which was already connected to the PC USB port on its other end.
Somehow, I could at last make Smart Switch finally start downloading the firmware from the web, and the device again disconnected (bootlooped), but luckily Smart Switch didn't care about it disconnecting, and kept on downloading the firmware. At about 85% of the progress bar state, I could find the downloaded firmware on the temp folders, which are described in this thread:
http://forum.gsmhosting.com/vbb/f777/samsung-firmware-download-belongs-his-serial-number-2038404/
I had to make sure it wasn't still downloading, and watched the "last modified" state of the file to make sure they are not being downloaded anymore. CAUTION: although the AP was not downloading anymore, I know it was probably not good as ODIN couldn't verify it when I tested it. USE ONLY SMART SWITCH !
I quickly copied the folder to which the app extracted the BL and AP files it downloaded, and finally had an officialy bootloader (BL) image, which I could use in ODIN in order to reupload a correct, "official" bootloader to the device....
I hoped the device won't bootloop in the middle, but luckily ODIN was fast enough to send the image successfully, with a "PASSED" status, and the device booted with a nice "Samsung" logo directly to a System Recovery page!
What I exactly did, was loading ODIN, then loading ONLY the BL file into the BL field in ODIN, having it verifying it, and once verified I connected the device, and as soon as ODIN recognized it, pushed START. It managed to upload the image into the device in a few seconds! It seems then, that the bootloop was not caused by a bad battery, but as a result of a corrupt upload of an AP image through ODIN - or because I possibly was using an incorrect version when I tried to upload an AP files to the device on my first attempt to flash it.
Note that I did search for the correct, compatible AP file, by country and model (on Sammobile) but it didn't' work (stuck at 50% in ODIN) ! so I really suggest everyone TO ONLY USE SMART SWITCH if they want to be sure that the correct firmware is being used, and avoid similar situations...
I then deleted the temp files from the PC (the actual ones which were in the temp folder), reinstalled the drivers from inside Smart Switch (just in case), booted the device to Download mode (WHICH DIDN'T BOOTLOOP this time), let Windows installing the drivers (checked in Device Manager), then restarted the PC, and ran Smart Switch again. I repeated the procedure of loading Emergency and Initialization, entering the model and serial number, having it fully downloading the firmware (again) from the web, and installing the firmware into the device. This time it completed the process, and I finally had the device installing and booting into a fresh version 6.0.1 of Android!
Hope it helps!
Alright. just to get this out of the way, I used to do tech support for HTC many moons ago. like back when they were *the* name in originating new tech to smart phones. I worked my ass off to get into the R&D team that handled all the new products that got released and to our product recovery team(the idiots that try to put a good light on a bad decision made by corporate). I have rooted and installed custom ROMS and recovery software on several phones from them as well as since then with the latest being my old galaxy S7 loaded up with TWRP and lineagoe OS(although i do not remember which version now)
But i did not do literally *ANY* of that with my Xiaomi MiA1. the phone functioned how i wanted it to out of the box and with the stock ROM, i had no need or desire to do anything with the ROM.
I have all but completely given up on doing this on my own now. I have gone over every guide on the MI forums for xiaomi and i think i may have even exhausted the ones that are available here now too. I am not sure WTH the problem at this point even is but here is the lowdown:
:fingers-crossed:
got the update near the end of December/beginning of January to update my MI A1 to the new android pie version that just came out OTA(i actually have two of these phones, one i have not updated since the first update to oreo, and this one that is hardbricked from after the PIE update)
At first when i got the OTA update, my phone started to act sluggish. simple apps like messenger, or google drive that had always worked flawlessly suddenly were taking ages to load. So like any sensible person, i pulled my info to my SD card, took it out, and then did a system recovery to restore factory defaults and start with a fresh OS again, just like when windows starts behaving poorly.
only this did not fix the problem. It persisted with poor performance after the factory data reset and upon my next reboot, my phone just stopped loading when it got to the MI logo on the screen. i literally let the phone sit on this screen overnight thinking just maybe it was being slow to boot after the reset. No luck and in the morning it remained at this screen.
just to make a note:
-phone was purchased off of amazon, i have reached out to the seller(it was a business)
-phone is in CANADA, so there are no service centers
-i CANNOT enter recovery mode(pwr + volup + voldn), it just freezes at the mi screen
-i CAN enter fastboot, but cannot flash room
-bootloader is locked and i have not yet found a method that will successfully unlock it
-the miflash tool does not work(on any version what-so-ever)
-the mi unlock tool gets to 50% and then fails, cannot unlock
-i have installed minimal adb for fastboot, none of the related commands succeed(yes system sees the phone:
c:\adb>fastboot devices
91c0963c0804 fastboot)
-i cannot unlock bootloader here and cannot install twrp or any other recovery image and it will not allow it even temporarily
I've gotten desperate enough to have even gone to the extreme and tried EDL mode by using test point to enter, computer recognizes the device even as the qualcom 9008, still no luck with any of the tools or ROMs provided on Xiaomi's website.
So be real with me here ladies and gents.... should i take this thing on my next trip up a telecomm tower and biff it as hard as i can at the ground(obviously in a snowless area for the most satisfaction) or can you saintly people actually offer me some support on this to turn my brick paperweight back into a phone again?
it is also worth mentioning that this is my first post here because i have never before had a problem with following any of he guides on here to accomplish any task i've ever set out to do with an android device, but this beastly lil mother is seriously making me consider becoming an iphone person(not really but do you get the frustration here?)
I'm writing this at 5:30 in the morning after being up all night working on this task so if my info is missing somewhere along the line just poke me with stick and i will fill in the blanks as needed.
I couldn't be bothered to get and load screenshots tonight but i will get some up tomorrow after sleep, for now i am going to the graveyard to rest.
Thanks for any responses in advance here.
What error show miflash when you try to flash in edl mode?
balannaer said:
Alright. just to get this out of the way, I used to do tech support for HTC many moons ago. like back when they were *the* name in originating new tech to smart phones. I worked my ass off to get into the R&D team that handled all the new products that got released and to our product recovery team(the idiots that try to put a good light on a bad decision made by corporate). I have rooted and installed custom ROMS and recovery software on several phones from them as well as since then with the latest being my old galaxy S7 loaded up with TWRP and lineagoe OS(although i do not remember which version now)
But i did not do literally *ANY* of that with my Xiaomi MiA1. the phone functioned how i wanted it to out of the box and with the stock ROM, i had no need or desire to do anything with the ROM.
I have all but completely given up on doing this on my own now. I have gone over every guide on the MI forums for xiaomi and i think i may have even exhausted the ones that are available here now too. I am not sure WTH the problem at this point even is but here is the lowdown:
:fingers-crossed:
got the update near the end of December/beginning of January to update my MI A1 to the new android pie version that just came out OTA(i actually have two of these phones, one i have not updated since the first update to oreo, and this one that is hardbricked from after the PIE update)
At first when i got the OTA update, my phone started to act sluggish. simple apps like messenger, or google drive that had always worked flawlessly suddenly were taking ages to load. So like any sensible person, i pulled my info to my SD card, took it out, and then did a system recovery to restore factory defaults and start with a fresh OS again, just like when windows starts behaving poorly.
only this did not fix the problem. It persisted with poor performance after the factory data reset and upon my next reboot, my phone just stopped loading when it got to the MI logo on the screen. i literally let the phone sit on this screen overnight thinking just maybe it was being slow to boot after the reset. No luck and in the morning it remained at this screen.
just to make a note:
-phone was purchased off of amazon, i have reached out to the seller(it was a business)
-phone is in CANADA, so there are no service centers
-i CANNOT enter recovery mode(pwr + volup + voldn), it just freezes at the mi screen
-i CAN enter fastboot, but cannot flash room
-bootloader is locked and i have not yet found a method that will successfully unlock it
-the miflash tool does not work(on any version what-so-ever)
-the mi unlock tool gets to 50% and then fails, cannot unlock
-i have installed minimal adb for fastboot, none of the related commands succeed(yes system sees the phone:
c:\adb>fastboot devices
91c0963c0804 fastboot)
-i cannot unlock bootloader here and cannot install twrp or any other recovery image and it will not allow it even temporarily
I've gotten desperate enough to have even gone to the extreme and tried EDL mode by using test point to enter, computer recognizes the device even as the qualcom 9008, still no luck with any of the tools or ROMs provided on Xiaomi's website.
So be real with me here ladies and gents.... should i take this thing on my next trip up a telecomm tower and biff it as hard as i can at the ground(obviously in a snowless area for the most satisfaction) or can you saintly people actually offer me some support on this to turn my brick paperweight back into a phone again?
it is also worth mentioning that this is my first post here because i have never before had a problem with following any of he guides on here to accomplish any task i've ever set out to do with an android device, but this beastly lil mother is seriously making me consider becoming an iphone person(not really but do you get the frustration here?)
I'm writing this at 5:30 in the morning after being up all night working on this task so if my info is missing somewhere along the line just poke me with stick and i will fill in the blanks as needed.
I couldn't be bothered to get and load screenshots tonight but i will get some up tomorrow after sleep, for now i am going to the graveyard to rest.
Thanks for any responses in advance here.
Click to expand...
Click to collapse
take your sd card off your phone i had similar issues and fixed them that way
ccalixtro said:
What error show miflash when you try to flash in edl mode?
Click to expand...
Click to collapse
it depends on which version of the flash tool is used. the beta version of the flash tool claims that it is successful, but the phone will not load to the Android OS after that is completed and it still will not load into the recovery mode to attempt to factory reset or anything else.
other versions have given errors:
miflash 2017.7.20.0 gives the response after attempting for about 10 seconds of "ACK count don't match!"
miflash 2018.11.15.0 gives the error response of "cannot receive hello packet"
and as stated before the miflash beta goes through the complete flash process with the result stating a "success" response, but the phone will not load to OS, just remains stuck on the MI logo screen when the phone is booting up
i have some screen grabs of all this but i am not yet worthy through XDA to be permitted to share them
thanks for the reply
kuartito said:
take your sd card off your phone i had similar issues and fixed them that way
Click to expand...
Click to collapse
i dismantled the phone manually bro, when you use EDL mode this way the SIM/SD tray is removed you then remove the entire backplate and then disconnect the battery cable from the circuit board and you use the test point method to short two pins that force the system to start in EDL mode when you connect the usb-C cable, so unfortunately that is not the issue :crying:
it never seems to be the simple solutions
Thanks for the reply!
Still dead in the water on this one.
Going to look into getting a replacement, that is a disappointing end to the Xiaomi experience
Facing similar issue. Am able to flash however still stuck when device is rebooted with this message;
Supported API: 3
E: Failed to clear BCB message: failed to FSync/dev/block/bootdevice/by-name/miscperation not permitted.