I wanted to factory reset my phone and I was on marshmallow. I had the update.zip file which I used while upgrading fronm lollipop to marshmallow. I thought that "apply update from sd card" in stock recovery and using that same update.zip would be a better way of doing the Factory Reset. The update's installation was aborted because of Status 7 Error Code and since then my phone is stuck in bootloop. The Moto Logo shows up and an android with the "Erasing" written below it follows and then it goes back and follows the same routine. So how can I restore my phone to stock official firmware on Locked Bootloader? I have never rooted my phone or unlocked the bootloader.
Please Help. I'm dying without my phone.
Since you messed up your phone, at this point you might as well try to flash stock firmware in fastboot. Can't get any worse.
Will he need an unlocked bootloader to be able to fastboot stock? I'm new to Motorolas. But I agree, that you need to follow a typical protocol - applying an update.zip when you are already on the update and you are stock, is not typical. Probably causing the issue. I think you can salvage it, I don't think you cannot recover from it. But I could be wrong. Set up Android SDK and go through the processes you'd need to unlock the bootloader and root. Once you have those set up, you can try to fastboot the lollipop return to stock tool.
Read through the mm release thread. In the beginning there are some posts from locked users who successfully flashed stock firmware to recover from issues.
Trying to update the 4.5.1 and it seemed to have gone fine until it automatically reboots into TWRP recovery. Upon rebooting into system, it states the update failed. With TWRP having all those jumbled folder names right now (has this been fixed yet?) it's hard to see if the update downloaded somewhere to internal storage, and further if it could be flashed even if I found it. Is updating with an OTA like this possible? I know on basically all other phone it is not. Has anyone gotten the update to work while being unlocked, rooted, with TWRP? Thanks.
xgerryx said:
Trying to update the 4.5.1 and it seemed to have gone fine until it automatically reboots into TWRP recovery. Upon rebooting into system, it states the update failed. With TWRP having all those jumbled folder names right now (has this been fixed yet?) it's hard to see if the update downloaded somewhere to internal storage, and further if it could be flashed even if I found it. Is updating with an OTA like this possible? I know on basically all other phone it is not. Has anyone gotten the update to work while being unlocked, rooted, with TWRP? Thanks.
Click to expand...
Click to collapse
Generally you need to reflash the previous Full ROM with TWRP and then flash the OTA on top for it to work as the system must be unmodified. Alternatively, you can just flash the latest Full ROM. Currently those are not available, but that's generally how it works.
If u have installed twrp before updating the stock rom, I guess we have to wait for full rom of latest update 4.5.1 which can be flashed via twrp.
P.s. FLASHING the dwnloaded update via twrp will gives u error.. So have to wait for full rom. ?
I am not responsible for your bricked phone or pigeon poo on your toupe. Do at your own risk.
Many thanks to @SupahCookie for idea and motivation!
INTENTIONALLY DOES --NOT-- LOCK BOOTLOADER!!!
Get factory images here:
https://forum.xda-developers.com/mo...ock-images-t3736767/post75236696#post75236696
THIS GUIDE IS FOR FACTORY/STOCK ROMs - NOT YOUR AVERAGE CUSTOM ROM which may not have bootloaders!!! (thanks!!!!! @echo92 )
FIX:
IF YOU ARE ABLE TO GET TO FASTBOOT THIS SHOULD WORK.
IF YOU HAVE 8.x bootloaders AND ARE DOWNGRADING TO 7, use "Alternative to RSDlite" below.
1 boot to win - 7 or 10 works fine.
2 boot phone to fastboot, and connect phone to computer.
3 start RSDlite
pick a ROM. I believe I used a 7.1.1 rom
3Nov9-ADDISON_NPNS26.118-22-2-8_cid50_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
RSDlite installed it and fixed the problem.
- -
I was then able to use RSDlite to install @rafikowy 's signed 8.0 . - going up from 7 to 8.
- -
- -
If you are on 8.x bootloaders and want to go to 7.x bootloaders, use this (RSDlite throws an error and stops):
ALTERNATIVE TO RSDlite:
1 I used 7zip to extract that 7.1.1 zip (or any ROM zip) into a folder x,
2 add all the adb and fastboot junk to folder x,
3 add the attached file (rename it to flash.bat) to folder x.
4 boot phone to fastboot and connect to computer.
5 click on flash.bat - it throws a lot of "slot" errors but works just fine.
6 reboot your phone if it hasn't already and go through the 7.x install stuffs.
7 you will not show an IMEI if you are coming from an 8.x bootloader. However, it IS there.
NOTE: you may need to add a line to the flash.bat if there are more/less sparsechunk's in your FACTORY/STOCK ROM...
THIS IS NOT FOR CUSTOM ROMs!!!!!!!
EDIT: 3-8-19: I just did this myself to go back very briefly to 7.1 - be sure you don't flash TWRP to it if your going to take OTAs - it will brick it. boot to TWRP if you need TWRP briefly: fastboot boot twrpimg.img
----------
If you can boot to fastboot screen, you can do anything.
Never OTA a ROM if you have modified recovery (TWRP, etc) or if magisk is present.
https://forum.xda-developers.com/mo...p-flashing-t3813498/post77011495#post77011495
I changed the attached file to add pause and reboot and exit to make it slightly more automated.
I have successfully used this many times going back and forth. If you can boot to fastboot screen, you can save your phone and flash anything you want.
You may wish to advise users that if they downgrade to Nougat not to use Nougat OTA updates. The reason being that a downgraded stock Oreo device may still have the Oreo bootloader on it. Thus, attempting to use Nougat OTA updates may hard brick their device (as the bootloader is likely corrupted, meaning no fastboot).
Users could either use the Feb 2018 NPN26.118-22-2-17 firmware from your link https://mirrors.lolinet.com/firmware/moto/addison/official/RETAIL/ as that was the last Nougat firmware (and thus no Nougat OTA updates) or avoid using OTA updates whilst downgraded.
echo92 said:
You may wish to advise users that if they downgrade to Nougat not to use Nougat OTA updates. The reason being that a downgraded stock Oreo device may still have the Oreo bootloader on it. Thus, attempting to use Nougat OTA updates may hard brick their device (as the bootloader is likely corrupted, meaning no fastboot).
Users could either use the Feb 2018 NPN26.118-22-2-17 firmware from your link https://mirrors.lolinet.com/firmware/moto/addison/official/RETAIL/ as that was the last Nougat firmware (and thus no Nougat OTA updates) or avoid using OTA updates whilst downgraded.
Click to expand...
Click to collapse
Interesting. I used the above GUIDE to go up and down a number of times on my phone (about 20 total) , installing and running on both 7 and 8, and then went down to a Nov 7.1.1 and let it ota all the way up to 8.0 and that is what I am using now. I found that when i used a factory zip, and the above procedure, it corrected the bootloaders to the appropriate version that i was flashing - either RSDlite or the more manual path which ignores the errors worked for me.
Using the above procedure , you get the correct bootloaders, which are in the zip.
Please correct me if i am wrong!
KrisM22 said:
Interesting. I used the above GUIDE to go up and down a number of times on my phone (about 20 total) , installing and running on both 7 and 8, and then went down to a Nov 7.1.1 and let it ota all the way up to 8.0 and that is what I am using now. I found that when i used a factory zip, and the above procedure, it corrected the bootloaders to the appropriate version that i was flashing - either RSDlite or the more manual path which ignores the errors worked for me.
Using the above procedure , you get the correct bootloaders, which are in the zip.
Please correct me if i am wrong!
Click to expand...
Click to collapse
That's intriguing - we saw previously on Z Play that users downgrading their stock firmware (e.g. https://forum.xda-developers.com/moto-z-play/help/hard-brick-moto-z-play-patch-abril-t3782927 )and then using OTA updates hard bricked their device (hence the number of users asking for a blankflash, as fastboot no longer works). I don't know if these users hard bricked by downgrading their firmware too far and then flashed an OTA radically different to their previous firmware, or whether it's a risk that's taken by any downgrading of firmware.
When you used fastboot, did you see any 'security downgrade errors' when you flashed the bootloader, and is your bootloader version now C180, as you've flashed the Oreo OTA?
echo92 said:
That's intriguing - we saw previously on Z Play that users downgrading their stock firmware (e.g. https://forum.xda-developers.com/moto-z-play/help/hard-brick-moto-z-play-patch-abril-t3782927 )and then using OTA updates hard bricked their device (hence the number of users asking for a blankflash, as fastboot no longer works). I don't know if these users hard bricked by downgrading their firmware too far and then flashed an OTA radically different to their previous firmware, or whether it's a risk that's taken by any downgrading of firmware.
When you used fastboot, did you see any 'security downgrade errors' when you flashed the bootloader, and is your bootloader version now C180, as you've flashed the Oreo OTA?
Click to expand...
Click to collapse
YES - that's why I wrote these 3 guides - before, it was quite possible to wind up with a bootloader mix - esp depending on the zip you use! - factory/stock only!!!
I added a line to the guide saying that it is only intended to be used for the factory/stock zips as these have (I believe) the bootloaders appropriate to the ROM.
Many thanks for pursuing this! - I wonder if we'll have to exclude certain ROMs that are in the factory lists?????
echo92 said:
That's intriguing - we saw previously on Z Play that users downgrading their stock firmware (e.g. https://forum.xda-developers.com/moto-z-play/help/hard-brick-moto-z-play-patch-abril-t3782927 )and then using OTA updates hard bricked their device
Click to expand...
Click to collapse
If you have TWRP (or I assume any custom recovery) present when you try to ota, it can download just fine and then reboot to the update. I had TWRP and wound up in a situation where my phone would only boot to twrp no matter what I flashed or restored. I booted phone to fastboot, RSDlite'ed that 11-09-17 factory zip and all was well. In that particular case I did not fully install 7.x but immediately RSDlite'ed rafikowy's 8.0 signed stock and went on with my testing. Since then I always boot to TWRP rather than intalling it and do my thing. (thanks @jceballos )
When you used fastboot, did you see any 'security downgrade errors' when you flashed the bootloader, and is your bootloader version now C180, as you've flashed the Oreo OTA?
Click to expand...
Click to collapse
Sorry - since it throws a million errors I never look at it if it works.
The particular build I am on at the moment - is BL: C1.82
This one started from that Nov '17 build and ota'ed all the way to 8.0 Apr.
I root and unroot as needed per rafikowy's method but using a boot to TWRP - never an install TWRP.
I'll put up a new guide ref ota and recovery and brick.
KrisM22 said:
If you have TWRP (or I assume any custom recovery) present when you try to ota, it can download just fine and then reboot to the update. I had TWRP and wound up in a situation where my phone would only boot to twrp no matter what I flashed or restored. I booted phone to fastboot, RSDlite'ed that 11-09-17 factory zip and all was well. In that particular case I did not fully install 7.x but immediately RSDlite'ed rafikowy's 8.0 signed stock and went on with my testing. Since then I always boot to TWRP rather than intalling it and do my thing. (thanks @jceballos )
Sorry - since it throws a million errors I never look at it if it works.
The particular build I am on at the moment - is BL: C1.82
This one started from that Nov '17 build and ota'ed all the way to 8.0 Apr.
I root and unroot as needed per rafikowy's method but using a boot to TWRP - never an install TWRP.
I'll put up a new guide ref ota and recovery and brick.
Click to expand...
Click to collapse
1) If you have TWRP, then using an OTA will fail - as you've not got stock recovery (and likely other modifications, including possibly a system partition set to read-write status). As you noted, having TWRP seems to cause a bootloop when rebooting - I'm not sure if the OTA sets a boot flag to stay in recovery until the update is completed. For the G4/Plus, there's a possible solution by wiping the misc partition but I don't know if there's a similar partition for Z Play devices: https://forum.xda-developers.com/moto-g4/help/troubleshooting-twrp-boot-loop-ota-t3714325
The only other solution I've seen is a clean flash of the stock ROM to get your device booting properly.
Booting to TWRP rather than flashing would mean your stock recovery is still present on your device. The only downside is if you need to make modifications, you'd need your computer to boot to TWRP.
2)BL C1.82 seems to be the bootloader provided by the Oreo April 2018 security patch update, so your device looks to be on the right bootloader. It's still curious that the Nov 2017 firmware worked whereas countless other 'factory' stock ROMs caused hard bricks when downgraded to and then OTA updates were installed.
As you mentioned, custom ROMs don't have bootloaders and thus don't care about your bootloader version usually (though I've seen some ROMs require a certain bootloader). However, stock ROMs and stock OTA updates do have bootloaders, which is why downgrading can be risky.
echo92 said:
1) If you have TWRP, then using an OTA will fail - as you've not got stock recovery (and likely other modifications, including possibly a system partition set to read-write status). As you noted, having TWRP seems to cause a bootloop when rebooting - I'm not sure if the OTA sets a boot flag to stay in recovery until the update is completed. For the G4/Plus, there's a possible solution by wiping the misc partition but I don't know if there's a similar partition for Z Play devices: https://forum.xda-developers.com/moto-g4/help/troubleshooting-twrp-boot-loop-ota-t3714325
The only other solution I've seen is a clean flash of the stock ROM to get your device booting properly.
Booting to TWRP rather than flashing would mean your stock recovery is still present on your device. The only downside is if you need to make modifications, you'd need your computer to boot to TWRP.
2)BL C1.82 seems to be the bootloader provided by the Oreo April 2018 security patch update, so your device looks to be on the right bootloader. It's still curious that the Nov 2017 firmware worked whereas countless other 'factory' stock ROMs caused hard bricks when downgraded to and then OTA updates were installed.
As you mentioned, custom ROMs don't have bootloaders and thus don't care about your bootloader version usually (though I've seen some ROMs require a certain bootloader). However, stock ROMs and stock OTA updates do have bootloaders, which is why downgrading can be risky.
Click to expand...
Click to collapse
Downgrading is a piece of cake if you don't use RSDlite - it throws an error and stops. Using the bat file it can happily throw all the errors it wants and all I care is at the end I have what I want.
It does indeed change the entire environment when you bat file the zip contents. You can bat file to get from 8 to 7 and then use RSDlite to flash a different 7 OR 8 zip file. There is no resulting difference in whether you RSDlite it or bat file it - the bat file simply comes from the .xml file that is within the zip. There is very little or no difference between that among addison factory/stock zips. Other zips are different (custom ROMs.)
Grab any factory/stock zip for addison and expand it and you will see modems, bootloaders, indeed absolutely everything you would find on that phone if you went to a store and bought it. SupahCookie simply added a couple lock command lines because it was intended for folks who somehow thought that if phone was locked they could take it back to the store and get their money back. Or some such. I found that ATT folk didn't care if you were on CM or whatever if you just needed to swap SIMs or whatever.
I DON'T want to lock the phone as it prevents me from modifying forever. Oh yeah that reminds me I was going to post the obligatory guide (again) about how to flash a white boot logo so you don't get that message - it's still there LOL but since the font is in white, you can't see it.
I have a Moto Z2 Play and used this to get out of a rather sticky situation.. My IEMI shows 0 now and I'm curious if there's a way to fix this? Also, You say you've done OTA updates? My phone is telling my I have some, is it safe to try?
Necrowr said:
I have a Moto Z2 Play and used this to get out of a rather sticky situation.. My IEMI shows 0 now and I'm curious if there's a way to fix this? Also, You say you've done OTA updates? My phone is telling my I have some, is it safe to try?
Click to expand...
Click to collapse
Thanks for feedback and great on success.
IMEI will show zero if using oreo, It will show again if using N. Remember that if you go from O to N you need to use the "Alternative to RSD" as RSD will simply throw an error and stop.
If you have TWRP and/or Magisk you must get rid of them before ota - if twrp present you will soft brick and have to do alternative again - flash a stock recovery. Simply uninstalling/flash magisk will probably not be enough - it will likely d/l but error part way through update. If you are sitting on rafikowy's stock oreo, and haven't modified it, you should be fine. I know Apr and June are out there. I flashed his stock 8.0 and took June fine. Z2 should be no different though of course I can't guarantee it
If you have success, let us know what you have done so others looking in will know. Thanks!
KrisM22 said:
Thanks for feedback and great on success.
IMEI will show zero if using oreo, It will show again if using N. Remember that if you go from O to N you need to use the "Alternative to RSD" as RSD will simply throw an error and stop.
If you have TWRP and/or Magisk you must get rid of them before ota - if twrp present you will soft brick and have to do alternative again - flash a stock recovery. Simply uninstalling/flash magisk will probably not be enough - it will likely d/l but error part way through update. If you are sitting on rafikowy's stock oreo, and haven't modified it, you should be fine. I know Apr and June are out there. I flashed his stock 8.0 and took June fine. Z2 should be no different though of course I can't guarantee it
If you have success, let us know what you have done so others looking in will know. Thanks!
Click to expand...
Click to collapse
I actually flashed to this: ALBUS_C_7.1.1_NPS26.118-24_cid50_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip Which is a 7.1.1 variant and it is showing 0 when I check settings and when I dial *#06#. However upon connecting to the computer and running mfastboot getvar imei it returned a value. I only did the steps above which would mean I don't have TWRP or Magisk (when I fastboot and click recovery I get "no command")
****** Additional information *********
XT1710-01 Duel Sim Variant
I started your steps, only being able to access fastboot. The device would throw an error (I don't recall exactly but it ended up showing me them in the bootloader logs) whenever I tried to start it, or go to recovery. #DefinitelyThoughtItWasDead
Necrowr said:
I actually flashed to this: ALBUS_C_7.1.1_NPS26.118-24_cid50_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip Which is a 7.1.1 variant and it is showing 0 when I check settings and when I dial *#06#. However upon connecting to the computer and running mfastboot getvar imei it returned a value. I only did the steps above which would mean I don't have TWRP or Magisk (when I fastboot and click recovery I get "no command")
****** Additional information *********
XT1710-01 Duel Sim Variant
I started your steps, only being able to access fastboot. The device would throw an error (I don't recall exactly but it ended up showing me them in the bootloader logs) whenever I tried to start it, or go to recovery. #DefinitelyThoughtItWasDead
Click to expand...
Click to collapse
What rom was on phone when you got it and what have you done to it? Has it ever run 8.x?
original country of phone?
The bat file will always throw a lot of slot errors.
https://mirrors.lolinet.com/firmware/moto/albus/official/RETUS/
or
https://mirrors.lolinet.com/firmware/moto/albus/official/RETAIL/
might have some stock ROMs of interest...
KrisM22 said:
What rom was on phone when you got it and what have you done to it? Has it ever run 8.x?
original country of phone?
The bat file will always throw a lot of slot errors.
might have some stock ROMs of interest...
Click to expand...
Click to collapse
It had 7.1.1 stock. I rooted it, and then flashed Resurrection Remix (which was yes 8.1 I believe) and the upgraded bootloader. I then found out my service wouldn't work with that.. so I attempted to flash back to stock which gave me a flurry of issues.. eventually getting to nothing but fastboot working. Flashed back to working with your guide to 7.1.1
If it helps in in fastboot it tells me BL: C0.CD
Necrowr said:
It had 7.1.1 stock. I rooted it, and then flashed Resurrection Remix (which was yes 8.1 I believe) and the upgraded bootloader. I then found out my service wouldn't work with that.. so I attempted to flash back to stock which gave me a flurry of issues.. eventually getting to nothing but fastboot working. Flashed back to working with your guide to 7.1.1
If it helps in in fastboot it tells me BL: C0.CD
Click to expand...
Click to collapse
Custom ROMs won't usually update the bootloader (even if they are newer) as stock ROMs typically only have the bootloader firmware.
You could look into flashing the stock Oreo albus 8.0 ROM https://forum.xda-developers.com/z2-play/how-to/fastboot-rom-oreo-retail-via-fastboot-t3786153 or the 8.0 June 2018 firmware https://forum.xda-developers.com/z2-play/how-to/fastboot-rom-albusretail8-0-0opss27-76-t3822195 but please check that firmware has been released for your device variant.
I don't know if updating your baseband to stock Oreo formally may fix your IMEI issue.
Necrowr said:
It had 7.1.1 stock. I rooted it, and then flashed Resurrection Remix (which was yes 8.1 I believe) and the upgraded bootloader. I then found out my service wouldn't work with that.. so I attempted to flash back to stock which gave me a flurry of issues.. eventually getting to nothing but fastboot working. Flashed back to working with your guide to 7.1.1
If it helps in in fastboot it tells me BL: C0.CD
Click to expand...
Click to collapse
"BL: C0.CD" even right after flashing that albus 7.1.1 using "alternative" above?
What happens if you flash one of the oreo roms from the links I gave you above?
Yeah, RR wouldn't change bootloaders... so you upgraded bootloaders independendently?- that could easily lead to a soft brick... -
I read RR on Z2 and it says nothing about bootloaders even though it says 8.1 based, so i wonder if it needs 7.x bootloaders? I did not read entire thread...
In a reverse, I would wonder if you put an 8 on there if you wouldn't see your IMEI. (On the Z if you flash 8 You won't see the IMEI until you return to 7.)(wondering if z2 is reversed)
KrisM22 said:
"BL: C0.CD" even right after flashing that albus 7.1.1 using "alternative" above?
What happens if you flash one of the oreo roms from the links I gave you above?
Yeah, RR wouldn't change bootloaders... so you upgraded bootloaders independendently?- that could easily lead to a soft brick... -
I read RR on Z2 and it says nothing about bootloaders even though it says 8.1 based, so i wonder if it needs 7.x bootloaders? I did not read entire thread...
In a reverse, I would wonder if you put an 8 on there if you wouldn't see your IMEI. (On the Z if you flash 8 You won't see the IMEI until you return to 7.)(wondering if z2 is reversed)
Click to expand...
Click to collapse
Yes, right after flashing that is the BL that fastboot is showing me. I don't recall updating the bootloader so to speak, however RR did require an updated variant of twrp which I flashed 3.2.2 I believe to get (unsure if that would have changed the bootloader or not). I also tried flashing a stock Oreo (which you've stated stock Roms usually only have the bootloaders so maybe somewhere during this process I updated it?). I wish I had all the notes for what I did to give more precise information, but I'm in a position where I really need my phone so I kinda just panicked and started flashing things when my service wouldn't work.
I'm highly considering trying to run an OTA (though very afraid of bricking). - On a side note though, it wouldn't even tell me I had OTA's until I did the steps in the original post here (doing the different 7.1.1. and 8.0 flashes, it wouldn't ever tell me I had updates, and now it does).
*** Edit ***
Looks like I'm able to enter stock recovery, which makes me believe everything is stock at the moment.
Necrowr said:
Yes, right after flashing that is the BL that fastboot is showing me. I don't recall updating the bootloader so to speak, however RR did require an updated variant of twrp which I flashed 3.2.2 I believe to get (unsure if that would have changed the bootloader or not). I also tried flashing a stock Oreo (which you've stated stock Roms usually only have the bootloaders so maybe somewhere during this process I updated it?). I wish I had all the notes for what I did to give more precise information, but I'm in a position where I really need my phone so I kinda just panicked and started flashing things when my service wouldn't work.
I'm highly considering trying to run an OTA (though very afraid of bricking). - On a side note though, it wouldn't even tell me I had OTA's until I did the steps in the original post here (doing the different 7.1.1. and 8.0 flashes, it wouldn't ever tell me I had updates, and now it does).
*** Edit ***
Looks like I'm able to enter stock recovery, which makes me believe everything is stock at the moment.
Click to expand...
Click to collapse
If you flashed a stock O that would have changed bl to O, but doing the above with the stock 7.1.1 would have changed them back to N. No matter (other than academic) that you don't remember the path - flashing a stock anything reverts it to that point in time. However, IMEI may have been moved - don't know. It will likely show on EITHER 7.x or 8.x stock - just don't know which.
If you flash a stock 8.x from those links I gave you above, it should offer you ota, ASSUMING there are any at this point in time(Z has 2). Adding Magisk at any point seems to hose you for receiving any more ota's - don't understand why, even with magisk uninstall, so that would mean going back to the latest stock and losing what you have (which is why I try to take a TBPro and copy that backup to PC (because re-flashing 8.x stock will likely reset internal storage.).
yes, if you enter stock recovery, you are likely at stock, though you could reflash the latest 7 or 8 stock to be sure, depending on which you want to use as base. Since 8 is having security fixes released, I choose 8 and will likely have no more interest (no time!) in 7.
So, ran the OTA and it was fine running the update and staying on N. I also downloaded the OTA for Oreo, when trying to update the recovery error'd out. It looked like the error said "Error in modem unexpected results" or something similar.
Necrowr said:
So, ran the OTA and it was fine running the update and staying on N. I also downloaded the OTA for Oreo, when trying to update the recovery error'd out. It looked like the error said "Error in modem unexpected results" or something similar.
Click to expand...
Click to collapse
did it offer to let you d/l it again? you could try that.
However, there exist O stock zips in those links I gave you so you could just flash the latest...
I had a Media Pad M3 with unlocked bootloader, rooted and TWRP as recovery. As I wanted to update my ROM to BTV-DL09C100B311 I had some problems in TWRP an thought updating step by step would be a good idea. So I downloaded all missing ROMs throught FrimwareFinder and startet with BTV-DL09C100B307_fullOTA.
The installation in TWRP with ADP sideload worked and when I restartet my device a was a bit suprised that the yellow "Bootloader is unlocked - your device is unsecure" message was missing. I restarted again and the message is still missing. I thought OK perhaps I can now install all updates through the EMUI build in process without FirmwareFinder or TWRP.
EMUI downloaded the update and asked me to restart and install. After the restart the install process went to 20% and told me then there was a verification error. When I restarted the tablet again I got a screen similar to the yellow "Bootloader is unlocked - your device is unsecure". The screen is red an told me "Your device has failed verification an may not work properly".
Now I'm stuck. No updates work and TWRP could not be started or installed again.
I tried reinstall TWRP with fasboot (https://forum.xda-developers.com/mediapad-m3/development/twrp-greatslon-mod-t3489232) but I get the error FAILED (remote: "command not allowed"). I tried the newest TWRP mod from https://androidfilehost.com/?w=files&flid=125388 but same error.
Phone and FRP are still unlocked, as shown in FASTBOOT&RESCUE MODE so this is not the cause of the above mentioned fastboot error.
I installed the Android SDK completly and downloaded the newest toolkit (https://developer.android.com/studio/releases/platform-tools) but still get the above error. So I dont think its a driver problem either.
I did not try to unlock the bootloader again. I don't think this makes sense even if I still have the original codes.
I would like to get TWRP back and update the tablet to the newest ROM version. And it would also be nice to know what happened here
Thanks in advance for everyone helping me back on track. I think the first step should be get over the FAILED (remote: "command not allowed") error and install TWRP again.
I got it
Needed to unlock the bootloader again. Even so it throws an error the red starting screen disappeared an I got the usual yellow one back and i could install TWRP.
//Edit
Managed to get to newest Version with this updater: https://forum.xda-developers.com/honor-9/development/tool-flash-official-firmware-recovery-t3769279
sebbo2015 said:
I got it
Needed to unlock the bootloader again. Even so it throws an error the red starting screen disappeared an I got the usual yellow one back and i could install TWRP.
//Edit
Managed to get to newest Version with this updater: https://forum.xda-developers.com/honor-9/development/tool-flash-official-firmware-recovery-t3769279
Click to expand...
Click to collapse
I am also looking for a way to update my rooted M3 (WiFi edition) to the latest available version with security patch line of November.
Now I wonder whether with this updater in your post above this works immediately or if I also have to go through all the difficulties you faced?
Is it possible to install updates with a rooted device with this updater or do you always need to unlock the bootloader again?
Thanks for your help!
Just tried it out now and it worked! Data is still there, homescreen icons are a little bit messed up and root is gone (no problem).
This is great because I was looking now for a long time to find a way to update a rooted M3 with new OTA updats (all the usual way fails).
I used to do it with going back to stock and a factory reset being involved.
Funny that you presented me the solution with your problem.
Glad that you shared it.
Now the only thing I am missing is to install the Xposed Framework on the M3. If you know how to do this let me know (I am using Super SU).
Borkse said:
Funny that you presented me the solution with your problem.
Glad that you shared it.
Now the only thing I am missing is to install the Xposed Framework on the M3. If you know how to do this let me know (I am using Super SU).
Click to expand...
Click to collapse
Im happy I could help. I dont use Xposed.
Hi, can you, please, describe this in steps? What I have to do before standard OTA update should work? And when (and how) to open bootloader once more? Thank you very much.
Standard ota updates will not work. If you already have an unlocked bootloader you have to use this method https://forum.xda-developers.com/honor-9/development/tool-flash-official-firmware-recovery-t3769279 to manual update your M3 to the newest version.
If you have no unlocked bootloader please check this first https://forum.xda-developers.com/mediapad-m3/development/twrp-greatslon-mod-t3489232
Hello,
I'm having big problems flashing any ROM on my Oneplus 5 atm.
At the beginning of this month, I wanted to unroot my rooted Android 8.0 or 8.1 (One of them, it was OxygenOS, but not the newest version)+ Xposed Oneplus 5.
I got a couple of errors, most of the time error 7.
After hours, old and new recoverys (TWRP) from blu_spark, codeworkx and some xda user recoverys and diffrent OxygenOS versions i finally managed it to install a Oxygen version with Android 7.1.1 on the phone. The Problem was: I always got errors (Installation failed) when I wanted to intall Software Updates no matter if I tryed it by myself or with the official system update in android.
So and today the official beta build of OxygenOS for 9.0 released and I was so stupid and thought I can make this an easy one.
Now I'm sitting here since 9:30am and try to flash Android 9, or any Android except 7.1.1 (only Oxygen Versions). Most of the Time i'm getting ERROR:7, it doesnt matter with which Recovery or Build.
When I got this problem at the first Time, my Phone was shown as "" (The error was something like: This Package is for a "Oneplus 5" this is a "").
When I get this scentence now (not every Recovery is showing it) it says my Phone is a "OnePlus5T", but i have a Oneplus 5.
Also (maybe partly) important things are:
- I tryed to edit the updater-script and delete the assets lines but there were no asset lines. Tryed it anyways and it didnt work. (and i really dont want to try this again)
I tryed to google this error for hours and many people meant that this is the way to go but I dont belive it. Isn't there any way to rename my phone, if yes: what do I have to do? I have TWRP and access to the command prompt aswell. If anyone can successfully create the 9.0 beta without the assets I would be happy but i dont think that is the solution for my problem, just a workaround.
- I think the problem is just something about my devices name. The strange part is that it accepted 7.1.1. And this was 100% a Oneplus 5 ROM.
- 7.1.1 isnt the way to go for me anymore. I dont like android 7 and it has so old security patches..
- Fingerprint sensor and screen got replaced
thank you for reading this and maybe helping me. I dont have the best language skills, if you need more Information about my Phone, please ask
EDIT1: As I said, 7.1.1 is still successfull, i tryed it a couple of mins ago. no error 7 or sth
maybe you can try revert to fully stock setup{without TWRP) and update to pie?
I have problem with error 7 when i tried to flash latest open beta (pie). I didn't find any solution.... :crying:
petryrety said:
I have problem with error 7 when i tried to flash latest open beta (pie). I didn't find any solution.... :crying:
Click to expand...
Click to collapse
Make sure the download isn't corrupt or if you extract the compatibility.zip use a recommended tool.
I had this problem couple of months ago. I solved it by flashing an old os version then flashing stock recovery(I don't remember if I locked the bootloader). boot in to the phone and download and update through ota( I did 3 updates this way). Then install twrp and root. Now I can flash any oos update without error 7.
May work
This is a post I wrote for another thread. I have found that this method fixes the error 7 issue, and allows you to update all the way to Pie without issues. When updating to Pie, use 7-Zip, not winrar or any other non-recommended programs to remove compatibility.zip from the firmware archive before flashing. I found that winrar causes treble errors or error 7.
https://forum.xda-developers.com/showpost.php?p=78523940&postcount=13
iwantademo123 said:
This is a post I wrote for another thread. I have found that this method fixes the error 7 issue, and allows you to update all the way to Pie without issues. When updating to Pie, use 7-Zip, not winrar or any other non-recommended programs to remove compatibility.zip from the firmware archive before flashing. I found that winrar causes treble errors or error 7.
https://forum.xda-developers.com/showpost.php?p=78523940&postcount=13
Click to expand...
Click to collapse
Yeah, that's what I wrote here https://forum.xda-developers.com/oneplus-5/help/massive-problems-error7-t3878372/post78503983 and in flashing instructions for open beta and stable builds in their first posts.
strongst said:
Yeah, that's what I wrote here https://forum.xda-developers.com/oneplus-5/help/massive-problems-error7-t3878372/post78503983 and in flashing instructions for open beta and stable builds in their first posts.
Click to expand...
Click to collapse
That's good, It's good advice. I am just stressing to everyone in this thread, how important it is to follow that and use a recommended tool to remove compatibility.zip because removing compatibility.zip sounds very trivial thing, but it's actually really important to use a tool like 7-Zip that doesn't break the firmware in the process.
Also, the link to my other post ( https://forum.xda-developers.com/showpost.php?p=78523940&postcount=13 ) should be detailed and comprehensive enough to help people with error 7 in other scenarios or that are trying to update to oreo or other stock firmwares too. This method restores the phone back to factory condition, including all the partitioning. Updating with a locked bootloader can fix a lot of update errors. I've found that after 5.1.5 it is safe to unlock the bootloader and take updates. But as you mentioned, for an unlocked bootloader, compatibility.zip needs to be removed from the firmware archive, and a tool such as 7-Zip must be used to do so as other archive managers break the update entirely (with error 7).
Good luck everyone trying to update, hope our advice helps :good:
So I flashed OOS 5.0.1 then went back to stock recovery. I then locked my bootloader. After which I booted into OxygenOS and updated it all the way to pie(took 3 OTAs). Now I've got a locked bootloader and pie but I'm wondering if the process to unlock the bootloader is the same or different now that there is a vendor drive?
TurtleSandals said:
So I flashed OOS 5.0.1 then went back to stock recovery. I then locked my bootloader. After which I booted into OxygenOS and updated it all the way to pie(took 3 OTAs). Now I've got a locked bootloader and pie but I'm wondering if the process to unlock the bootloader is the same or different now that there is a vendor drive?
Click to expand...
Click to collapse
The unlocking process of the bootloader is the same!
I am having the exact same problem, tried everything from above. Can get anything more recent than 7.1.1 on my oneplus 5. evrything else is error 7. Any update
mathgerm said:
I am having the exact same problem, tried everything from above. Can get anything more recent than 7.1.1 on my oneplus 5. evrything else is error 7. Any update
Click to expand...
Click to collapse
Please see here https://forum.xda-developers.com/on...xygenos-4-5-2-7-1-1-ota-t3627003/post79938097