XZ Premium Dead - Sony Xperia XZ Premium Guides, News, & Discussion

Hey guys,
My XZ Premium updated to 9.0. Since then I started to have many problems.
Yesterday a messagage appeared: Your phone is corrupt, it may not work properly. It can't be trusted.
Hours later it frozed and turned off. Now it's not responding to anything. The led isn't working and the device manager shows it as SOMC Flash Device.
The comands pressing volume buttons while I connect the USB cable are not working either.
Can I save it? I bought it three months ago :crying:

First, try to repair it with Sony Companion and Newflasher. if those not work return it to your dealer or ask for a repair under warranty.

Styler911 said:
First, try to repair it with Sony Companion and Newflasher. if those not work return it to your dealer or ask for a repair under warranty.
Click to expand...
Click to collapse
I alredy tried. It's not working. I bought in a different country that I live now. I can't use the local warranty.

first of all try a factory reset if the phone not modified.
If you have TWRP installed, wipe the phone out of TWRP.

Probably water in usb port then charging caused it

it cant hurt to try have you tried pressing volume up and power together until you get 3 vibrations?

mad0701 said:
first of all try a factory reset if the phone not modified.
If you have TWRP installed, wipe the phone out of TWRP.
Click to expand...
Click to collapse
I don't have the TWRP installed. The device is not responing via PC.:crying:

stipi69 said:
it cant hurt to try have you tried pressing volume up and power together until you get 3 vibrations?
Click to expand...
Click to collapse
The device is not responding to any command that I try...

amakuramio said:
Probably water in usb port then charging caused it
Click to expand...
Click to collapse
It never get wet, and when it does I make sure that no water remains....

Can you see your phone in the Systemcontrol? If yes: does the device is valid or does the device has an Akklamation Mark "!" beside? Maybe you must install the fastboot driver?
---------- Post added at 08:42 AM ---------- Previous post was at 08:37 AM ----------
on other hand:
try the Flash tool (Version 0.9.2.5.0) with a ftf file.
With this you can also change the version of country, remove a branding or viversa....
You will find links to the tool and ftf here in the forum

mad0701 said:
Can you see your phone in the Systemcontrol? If yes: does the device is valid or does the device has an Akklamation Mark "!" beside? Maybe you must install the fastboot driver?
---------- Post added at 08:42 AM ---------- Previous post was at 08:37 AM ----------
on other hand:
try the Flash tool (Version 0.9.2.5.0) with a ftf file.
With this you can also change the version of country, remove a branding or viversa....
You will find links to the tool and ftf here in the forum
Click to expand...
Click to collapse
It only appears as SOMC Flash Device. The ADB or Flash Tools can't get access to the internal memory. I know there's a way to access the internal memory. Just don't know which one yet.

It looks like a coincidence. Hardware not be working may be the real issue.
If you find a knowledgeable repair shop, they can clear your flash and install the original Sony shipped OS for a little money. Most of the time this is done from the USB after a factory reset explained by others here. However, if the USB port is not working then accessing the flash needs opening the unit which will cost you.
And then if the hardware has failed, none of this would help anyway.

What's happen, if you press for 6 Sec or longer Power and Volume up together?

Related

how to fix a bricked phone.

How do i rescue my bricked phone!
Click to expand...
Click to collapse
well the answer lies within this thread.
how do you brick a phone
well, there are many ways you can brick a phone.​1. you install the wrong software
2.you install a 'broken' rom
3. you install a recovery that isnt supported for our phone
4.or you were messing with your bootloader
etc etc... you get the point
how to rescue a bricked x8​1st: If you have done a soft brick then you can boot into xrecovery and restore your latest backup. easy
2:if restoring doesn'twork or you have a hard brick then you should either launch:SEUS (sony ericsson update service) or pc companion. click update and follow the steps.
3:if none of that works then you will have to send it off to se. if you dont get some kind of phone company to fix it then its as useless as a real brick lol or a replica of a phone.
3:you can use a flashtool to fix it as well. if you open flashtool you usally get a number of options such as unlock bootloader etc. there should be an option where you can restore it. (lol i think)
Cheers​i hope it helped. if it did then please do press the thanks button.
-wilbso​
Soft Brick is the common brick we get.
Hard Brick is a brick you can only get with messing with the bootloader. There's no complete brick.
Say something about flashtool too.
Chris95X8 said:
Soft Brick is the common brick we get.
Hard Brick is a brick you can only get with messing with the bootloader. There's no complete brick.
Say something about flashtool too.
Click to expand...
Click to collapse
ok. besides the complete brick is what i call doomsday. thats just my own little thing lol. and yes i will metion 'bout' the flashtool too
how about hard brick??
X8
I bricked my phone while a opened bootloader.Phone was not recognized SIM and i havent data connection too.SE PC repair does not helped me,backup file as well.Only helpful tool was S1Tool with "restore" button.It fixes my phone and i opened bootloader again with success!
Thanks for developers!!!
X8;OPENED BOOTLOADER;nAa kernel;DUAL TOUCH;GINGERXPERIA V17 2.3.7
montekristo said:
I bricked my phone while a opened bootloader.Phone was not recognized SIM and i havent data connection too.SE PC repair does not helped me,backup file as well.Only helpful tool was S1Tool with "restore" button.It fixes my phone and i opened bootloader again with success!
Thanks for developers!!!
X8;OPENED BOOTLOADER;nAa kernel;DUAL TOUCH;GINGERXPERIA V17 2.3.7
Click to expand...
Click to collapse
Quite a few people repaired their phones with s1 tool. Iv never actually hard bricked my phone. IV done soft brick> bootloop but I fixed that be restoring a backed in xrecovery so these replies I
Getting are quite helpful. As long as your phone is repaired everything is alright.
sent from my x8 running gingerdx
Hello, can you please help me! I bricked my xperia neo, while trying to update se tweaked rom v 8.5. Now i'm facing the "sony ericsson" screen, totaly blocked. I've tried many times to flash it, whith wotan client, flash tool, but it's imposible to enter flash mode again, no green led, only bocked se screen, please help!!! how did you manage o get into flash mode?
benga_mircea said:
I bricked my xperia neo, while trying to update se tweaked rom v 8.5. Now i'm facing the "sony ericsson" screen, totaly blocked. I've tried many times to flash it, whith wotan client, flash tool, but it's imposible to enter flash mode again, no green led, only bocked se screen, please help!!! how did you manage o get into flash mode?
Click to expand...
Click to collapse
On the W/X8 and X10 mini/Pro you can get into FLASH MODE by keeping the back button pressed while connecting the TURNED OFF phone by USB.
That being said, you have a NEO which doesn't work that way.
Your phone has "fastboot" - to get there ... turn off the phone, keep the bottom right key pressed and connect the USB cable to the PC.
What you have to do from there on out is either best asked in the RIGHT subforum or through Google research.
B.Jay said:
On the W/X8 and X10 mini/Pro you can get into FLASH MODE by keeping the back button pressed while connecting the TURNED OFF phone by USB.
That being said, you have a NEO which doesn't work that way.
Your phone has "fastboot" - to get there ... turn off the phone, keep the bottom right key pressed and connect the USB cable to the PC.
What you have to do from there on out is either best asked in the RIGHT subforum or through Google research.
Click to expand...
Click to collapse
how did you get this thread back up?
Sent from my X8 using XDA App
wilbso said:
how did you get this thread back up?
Click to expand...
Click to collapse
Hummm...?
I only replied to benga_mircea's post from today.
Or ... did I miss something? *notsure*
Thank you for your help, but I can't acces flash mode or fastboot mode again, lika I use to, after I connect the batery, push the back button, insert the usb, a few seconds and the "sony ericsson" screen pops up again and stays blocked. I think I've killed my phone
Well, for as long as you see the SONY ERICSSON boot logo - and I'm assuming from the way the X8 works here - the boot loader and kernel are intact; there's just a problem boot-strapping the system ROM (shot system, bad flash).
The real problem is that Fastboot isn't comparable to the Flash Mode of our phones ... it's very different.
In your stead I would try to find out how you can perform a "disaster restore" (like we do with our W/X8 through Flash Mode and Flashtool) by flashing back to stock.
Anyway ... just to repeat it ...
1. You need to TURN OFF your phone and DISCONNECT it from the computer/charger.
2. You insert the USB connector into JUST your phone.
3. You press the bottom/right button (also "Back"?) and keep it pressed while you connect the USB to the computer.
Once the phone connected to the computer as a (wild guess!) "Flash Device" or "Fastboot Device" you need the apropriate tool(s) and Stock ROM image - in case PC Companion refuses to repair your phone.
---------- Post added at 12:21 PM ---------- Previous post was at 12:18 PM ----------
Any chance this thread (in the Xperia Neo General section) could be of any help to you?
B.Jay said:
Hummm...?
I only replied to benga_mircea's post from today.
Or ... did I miss something? *notsure*
Click to expand...
Click to collapse
Where did you find it? I mean where did boy find the thread? My Sig? Looking through old posts?
Sent from my X8 using XDA App
B.Jay said:
Well, for as long as you see the SONY ERICSSON boot logo - and I'm assuming from the way the X8 works here - the boot loader and kernel are intact; there's just a problem boot-strapping the system ROM (shot system, bad flash).
The real problem is that Fastboot isn't comparable to the Flash Mode of our phones ... it's very different.
In your stead I would try to find out how you can perform a "disaster restore" (like we do with our W/X8 through Flash Mode and Flashtool) by flashing back to stock.
Anyway ... just to repeat it ...
1. You need to TURN OFF your phone and DISCONNECT it from the computer/charger.
2. You insert the USB connector into JUST your phone.
3. You press the bottom/right button (also "Back"?) and keep it pressed while you connect the USB to the computer.
Once the phone connected to the computer as a (wild guess!) "Flash Device" or "Fastboot Device" you need the apropriate tool(s) and Stock ROM image - in case PC Companion refuses to repair your phone.
---------- Post added at 12:21 PM ---------- Previous post was at 12:18 PM ----------
Any chance this thread (in the Xperia Neo General section) could be of any help to you?
Click to expand...
Click to collapse
Thanks! I tried like 50 times, and nothing, the ennoing "sony ericsson" is booting (no sony ericsson logo as usualy, just the writing) I flashed 10 times in the past whith no problem. Now, even when I put it to charge ( wall charge) the phone is turning on showing that stupid "sony ericsson" writting, I cant shut it down from the on\off button. Before killling it, I've instales stock MT15i_4.0.A.2.368_GLOBAL ROM, then I upgraded to MT15i_4.0.2.A.0.42_Global, then rooted with DooMLoRD_v4_ROOT-zergRush-busybox-su, Installed CWM( wiped cache, updated SE tweaked v8.5 Rom) After the restart, the "se" writting started booting. I've pulled out the batery, and begined flashing it with flash tool(no green led).The flashing started and my little brother accidentaly pulled out the Usb cable; that's the whole story! I've tried like 100 times with wotan, flash tool and FlashTool_0.2.9.1_FOTAUnbrick, no result, even if pc companion tells me "phone conected" and gives me further instructions whith the phone being dead, and the flash tool showing me to connect de device... Thank you for all the help, hope there is a solution. sorry for the long post and my bad english...
---------- Post added at 11:43 PM ---------- Previous post was at 11:24 PM ----------
04/040/2012 23:40:02 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/040/2012 23:40:04 - INFO - Device disconnected
04/040/2012 23:40:06 - INFO - Device connected with USB debugging off
04/040/2012 23:40:06 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/040/2012 23:40:07 - INFO - Device disconnected
04/040/2012 23:40:10 - INFO - Device connected with USB debugging off
04/040/2012 23:40:10 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/040/2012 23:40:18 - INFO - Device disconnected
04/040/2012 23:40:35 - INFO - Device connected with USB debugging off
04/040/2012 23:40:35 - INFO - For 2011 devices line, be sure you are not in MTP mode
Flash tooll results when trying to connect (pulling batery-10 secs, back butoon, usb cable)
benga_mircea said:
The flashing started and my little brother accidentaly pulled out the Usb cable; that's the whole story!
Click to expand...
Click to collapse
Whoa... that's what I call a "security vulnerability".
If the flash process got interrupted because your lil bro pulled the USB cable I'm somewhat certain the NAND is messed up pretty good - no wonder you're stuck at the SE boot logo.
If there's no way by which you can get the device back to normal (read: even the guys over in the Neo sub-board are out of ideas/help) I think your best shot would be to send it in to SE for repair if you still got warranty. SE should have other means to resurrect the device and slap it back into shape.
I'm sorry I can't really help you here with this - the Neo is different from the X8 and also different from the way my tablets work.
Thank's for the advice! My waranty is lost, i've unlocked the bootloader. Only if I could enter in flash mode!
benga_mircea said:
Thank's for the advice! My waranty is lost, i've unlocked the bootloader. Only if I could enter in flash mode!
Click to expand...
Click to collapse
Well, on my Samsung, which has Fastboot, I first enter Fastboot and from there I put the device into download mode for flashing (in theory you can compare "Download mode" to the "Flash mode" - in Flash mode the W/X8 awaits a ROM image to be flashed into the NAND, pretty much the same as "Download mode" works).
Since your Neo isn't completely dead (you just have a shot system due to the flash interruption) you only need to find a way how you can re-write the system.
I lack the time to research how the Neo works, but I think there should be a way to get the device going as you can even "resurrect" a W/X8 where you formatted the system partition (by mistake in CWM, for example). However, that's not as bad as interrupting the USB connection but about the same "ooops" to blank the system.
Flash mode not working, fastboot not workingI Tried a lot of programs (wotan, flash tool, fota unbrick tool, octopus, omnius for se, pc companion, se update. Non of them manages to connect to my phone. If only I could connect for 1 sec. I have a backup of TA, but I can flash it. Thanks anyway!
is it safe to unlock BL, if we have x8 with manuf.code 11W28? pls help me
NarutoDroid said:
is it safe to unlock BL, if we have x8 with manuf.code 11W28? pls help me
Click to expand...
Click to collapse
yes 11W30 or below should unlock fine but for me 11W33 also no problem
Sent from my E15i using xda premium

Help i totally bricked my lg g2 :(

Phone fixed, please delete the thread.
3S0PHAGOOS said:
I changed my ROM from stock to 4.4.2 ROM but I got so many issues so changed back to stock ROM, but my LG G2 only has now only 10gb of internal memory.. [I got 32gb lg g2] Now, i tried the instruction from the guy here
http://forum.xda-developers.com/showthread.php?t=2470207&page=3
and also this
http://forum.cyanogenmod.com/topic/...s-on-internal-storage/page__st__20#entry67870
I tried to do the steps as instructed but the result is not the same as mine and then i just exit ADB... then i restart my phone and booomm...
my phone died can't on at all even on download mode... when i try download mode it's just USB Not recognize... please help me ((((
Click to expand...
Click to collapse
Try connecting the phone to a wall charger for 15 mins,and then power up the phone.
nimrodsv said:
Try connecting the phone to a wall charger for 15 mins,and then power up the phone.
Click to expand...
Click to collapse
didn't work, as expected
3S0PHAGOOS said:
didn't work, as expected
Click to expand...
Click to collapse
At the second thread its for HTC incredible, i hope you didnt flashed anything from there right?
Honestly i have no idea what you can do, but trying to eliminate some of the cases..
EDIT: you should try the first method ( http://forum.xda-developers.com/showthread.php?t=2470207&page=3 ) when using this files: https://www.dropbox.com/sh/3pqceuaqsji0dqn/nvR20mLqMF
if that what you did and it didn't worked im guessing that flashing the firmware wont help, but there are wiser people than me to help you, just wait for their input
nimrodsv said:
At the second thread its for HTC incredible, i hope you didnt flashed anything from there right?
Honestly i have no idea what you can do, but trying to eliminate some of the cases..
EDIT: you should try the first method ( http://forum.xda-developers.com/showthread.php?t=2470207&page=3 ) when using this files: https://www.dropbox.com/sh/3pqceuaqsji0dqn/nvR20mLqMF
if that what you did and it didn't worked im guessing that flashing the firmware wont help, but there are wiser people than me to help you, just wait for their input
Click to expand...
Click to collapse
I can't flash anymore, My LG G2 is completely dead, can't get into recovery and download mode, if I tried going to download my pc just say "USB NOT RECOGNIZED"
I've used the following to completely restore my phone and untrip the root checker...
Verizon: http://forum.xda-developers.com/showthread.php?t=2448960
Others: http://forum.xda-developers.com/showthread.php?t=2432476
Xyriin said:
I've used the following to completely restore my phone and untrip the root checker...
Verizon: http://forum.xda-developers.com/showthread.php?t=2448960
Others: http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
did your phone totally bricked when you did it? or you can still go to the download mode?
cause mine is totally can't on.
Do you have the LG bootlogo coming up, if so try this:
(Something similar happened to mine, and I hope this will help.)\
Turn off phone, then when off, hold down power and volume down button until it reaches the LG logo and then release and hold it down again, if that doesn't work, when just hold it down until you see a screen that says something like: Hard reset/ factory reset. For me it took me to my recovery screen, where I just flashed a older ROM onto it, and you should be fine. I then later flashed a recovery file. I hope this helps, and if you need it any clearer, just reply :fingers-crossed:
If it's saying usb not recongized I'd recommend installing the proper drivers for your specific model. Which model do you have since you didn't specifying? Also, dead or charged your phone should boot download mode with volume up being held and plugging the phone in via usb to your computer.
---------- Post added at 08:22 PM ---------- Previous post was at 08:21 PM ----------
If it's Verizon, follow that posted method above correctly. Check for correct com port numbers and make sure replacing the dll file your in the c: drive and not just in your download folder.
hiddenfive said:
Do you have the LG bootlogo coming up, if so try this:
(Something similar happened to mine, and I hope this will help.)\
Turn off phone, then when off, hold down power and volume down button until it reaches the LG logo and then release and hold it down again, if that doesn't work, when just hold it down until you see a screen that says something like: Hard reset/ factory reset. For me it took me to my recovery screen, where I just flashed a older ROM onto it, and you should be fine. I then later flashed a recovery file. I hope this helps, and if you need it any clearer, just reply :fingers-crossed:
Click to expand...
Click to collapse
My phone is completely off
ceredics said:
If it's saying usb not recongized I'd recommend installing the proper drivers for your specific model. Which model do you have since you didn't specifying? Also, dead or charged your phone should boot download mode with volume up being held and plugging the phone in via usb to your computer.
---------- Post added at 08:22 PM ---------- Previous post was at 08:21 PM ----------
If it's Verizon, follow that posted method above correctly. Check for correct com port numbers and make sure replacing the dll file your in the c: drive and not just in your download folder.
Click to expand...
Click to collapse
I have the D802, I already installed the drivers.
If I'm going to go to download mode, It says USB not Recognized and my phone is completely off.
I don't have too much experience with that model so hopefully someone else spying has more information. Sorry buddy.
There is no bootlogo at all? Not even when you turn it on? Try plugging it into a wall charger and if anything happens, also try changing your COM # to 41, if it isn't its Device Manager<Ports (COM & LPT), right click< properties< port settings< advanced..< COM 41, this was from this article I will link right here: http://forum.xda-developers.com/showthread.php?t=2582142
Hope this helps :good:
@3S0PHAGOOS how you did the fix?
cpaixao said:
@3S0PHAGOOS how you did the fix?
Click to expand...
Click to collapse
yes please enlighten us....I am going through the same process and I can not turn it on at all. NOthing comes on...
Send it to me, but if I fix it I get to keep the phone. Right?
Sent from my SM-T210R using XDA Premium 4 mobile app
3S0PHAGOOS said:
Phone fixed, please delete the thread.
Click to expand...
Click to collapse
How did you fix it?
Those experiencing this problem could try this
https://www.youtube.com/watch?v=E7zbs6of_4I
Btw, you should share the solution for those who are in the same situation.

Phone Doesn't turn on

Hi,
I was using CM13 based Nuclea OS. Tried to Lock the bootloader using the tool provided in this forum. But after that, the phone kep on starting on and off continuously and showing only Zuk Z1 logo after each boot. Then I pressed Vol UP + Vol Down + Power button for some time and the phone switched off. Now I am not able to switch it on. Tried by holding all 3 buttons and power button alone as well. Battery was 90% when I did this. Any clue?
Thanks,
Sarin
Somehow I turned the phone on (tried multiple key combinations and one of them worked). But now the Phone is in a boot loop again, ie. The Logo and 'Powered by Android' message appears after a vibration and then it switches off. This is being coontinued for the past 8 hours.
That is because u have wiped all of ur phones data and phone is bricked now
..Try connecting to pc and install Twrp recovery by going to fastboot
Harijayan994_ said:
That is because u have wiped all of ur phones data and phone is bricked now
..Try connecting to pc and install Twrp recovery by going to fastboot
Click to expand...
Click to collapse
Fastboot was not detecting the phone as it's restarting continuously. Some how I switched off the phone (I Guess I pressed and hold Power button for a very very long time and then released). Then installed ZUI Version using QFIL. Did lot of search to get the Diag Port drivers and after that it detected and installed software.
Now trying to install Original CM 12.1 OS.
Coming to the real problem why I tried to lock boot loader - Now a days all apps started checking whether phone is rooted or not I guess. It's not allowing me to install the SBI Pay App or the new IRCTC App in India. (Though Root is disabled in settings). So is there a way to install CM13/CM14 without rooting the phone.
You can go to developmee option and there is an optiom for enabling root
.. enable it and enjoy apps
I guess you got me wrong. Apps gives error that 'Your phone is rooted, Please un-root to continue'. This shows up irrespective of Root is enabled or disabled in Developer options.
sarincv said:
Fastboot was not detecting the phone as it's restarting continuously. Some how I switched off the phone (I Guess I pressed and hold Power button for a very very long time and then released). Then installed ZUI Version using QFIL. Did lot of search to get the Diag Port drivers and after that it detected and installed software.
Now trying to install Original CM 12.1 OS.
Coming to the real problem why I tried to lock boot loader - Now a days all apps started checking whether phone is rooted or not I guess. It's not allowing me to install the SBI Pay App or the new IRCTC App in India. (Though Root is disabled in settings). So is there a way to install CM13/CM14 without rooting the phone.
Click to expand...
Click to collapse
Brother! There are a lot of Noobs here! (Myself one of them!). Now somehow you got saved! You took the time and toil to find a method. So I request you to kindly specify how you did that coz if anyone else get the same problem your post will be a life saver!
Hope you'll take the trouble to explain, type and provide links! But definitely if you do, one or the other guy will thank you with all this heart!
---------- Post added at 05:13 PM ---------- Previous post was at 05:10 PM ----------
sarincv said:
I guess you got me wrong. Apps gives error that 'Your phone is rooted, Please un-root to continue'. This shows up irrespective of Root is enabled or disabled in Developer options.
Click to expand...
Click to collapse
And yes... There is a way for that... Install Xposed. And try RootCloak... It's a root hider app. If it works then great. If not, let me know. There is another workaround.
Followed this tutorial to Flash ZUI Version. But for the Drivers I forgot which link I used. I can upload it to Google Drive and post it here.
http://www.androidbrick.com/lenovo-zuk-phones-qfil-roms-unbrick-guide/
sarincv said:
Followed this tutorial to Flash ZUI Version. But for the Drivers I forgot which link I used. I can upload it to Google Drive and post it here.
http://www.androidbrick.com/lenovo-zuk-phones-qfil-roms-unbrick-guide/
Click to expand...
Click to collapse
Alright bro... Then upload it and share the link please...

a2017, restore,relock,w/o touchscreen for warranty

Hello I have a "a2017u" model, without a working touchscreen. I need to sent it in for a warranty repair. can anyone explain to me how to restore the device, currently it has twrp+lineage os. I CAN'T use the touchscreen, however you can see everything, only touch doesn't work. I really need help since this is my only phone and I'm borrowing one.
So where are you getting stuck?
I don't think you need to use the screen for anything.
lafester said:
So where are you getting stuck?
I don't think you need to use the screen for anything.
Click to expand...
Click to collapse
I tried to use axon 7 toolkit, I run the check under option one and get this message.
So I don't know what's happening
cato1986 said:
I tried to use axon 7 toolkit, I run the check under option one and get this message.
So I don't know what's happening
Click to expand...
Click to collapse
EDIT: Some guy gave me an awesome idea: Use an OTG adapter and a USB mouse on TWRP. From there you can install some zips, I don't know anything about A2017s but you can look for guides on how to get to stock (not mine though)
Right. If you have an SD card I think you can:
- find a stock recovery.img, use fastboot to install it to recovery (fastboot flash recovery yourfile.img)
- then wipe data/factory reset with the stock recovery
- install an official system zip with your sdcard
You have a Chinese version phone so I don't have any recovery zips for that, sorry. If you can, look for the recovery img and send the link of where you got it here.
Axon7toolkit is a little bit too hardcoded, it needs adb first, then from ADB it boots to fastboot, then from there it boots a twrp img...
Well that's a no go. Besides the fact it refuses to show the mouse. It just doesn't work. I did manage to get to the desktop. But parts of the digitizer work and then it goes crazy clicking things on its own.
Chinese version? Mines the American. Zte a2017u
cato1986 said:
Chinese version? Mines the American. Zte a2017u
Click to expand...
Click to collapse
Then why did you write A2017 in the title and the OP?? Change that
---------- Post added at 05:16 AM ---------- Previous post was at 05:13 AM ----------
Okay there may be an easier way. Try putting your phone in FTM mode (while off, hold Vol down + power) and a message that says FTM mode should appear. Now try axon7toolkit.
Or, if you have an USB mouse and an OTG adapter, enable USB debugging and connect your phone to the PC. Then use axon7toolkit

Mi9T bricked / no OS / no adb / no fastboot /twrp working

Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
I'm really appreciate your hardwork ?
Only one solution you have left, open back panel of your phone and find two golden point of EDL mode and then hold two points with joint pin and remember your phone battery should be removed and then connect to pc with hold two golden points now your phone is in EDL MODE then flash with stock rom through mi flash tool and remember inside your pc Modem driver is installed which is required in EDL MODE then that's easier to roll back at initial state of phone ? now your phone work smoothly.
---------- Post added at 01:12 PM ---------- Previous post was at 01:11 PM ----------
I'm really appreciate your hardwork ?
Only one solution you have left, open back panel of your phone and find two golden point of EDL mode and then hold two points with joint pin and remember your phone battery should be removed and then connect to pc with hold two golden points now your phone is in EDL MODE then flash with stock rom through mi flash tool and remember inside your pc Modem driver is installed which is required in EDL MODE then that's easier to roll back at initial state of phone ? now your phone work smoothly.
Check
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
Thus is edl mode test pin points.
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
Edl mode via shorting out the tester point is the only way for you , I beleive your presist or crust partition might have been totally messed up that's why you phone is like this or maybe you didn't enable usb debugging by default luckily your bootloader isn't locked it it was locked then your might have become something like a paperblock of 200grams.
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
Have you tried flashing a rom using miflash https://www.xiaomiflash.com/?
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
i had the same problem years ago with another device ... try to go in twrp press the power botton for 15 sec rebot on twrp format data (not with advanced wipe) and after that a full wipe in advanced wipe.... And look if you solved the encrypt problem.... (Sorry for my bad english)...
---------- Post added at 06:40 PM ---------- Previous post was at 06:17 PM ----------
Yakusha90 said:
i had the same problem years ago with another device ... try to go in twrp press the power botton for 15 sec rebot on twrp format data (not with advanced wipe) and after that a full wipe in advanced wipe.... And look if you solved the encrypt problem.... (Sorry for my bad english)...
Click to expand...
Click to collapse
A lot of time an hard rebot can help... try you can't lose anything ...
I'm curious... let me know if it worked ...
---------- Post added at 08:00 PM ---------- Previous post was at 07:58 PM ----------
Yakusha90 said:
i had the same problem years ago with another device ... try to go in twrp press the power botton for 15 sec rebot on twrp format data (not with advanced wipe) and after that a full wipe in advanced wipe.... And look if you solved the encrypt problem.... (Sorry for my bad english)...
---------- Post added at 06:40 PM ---------- Previous post was at 06:17 PM ----------
A lot of time an hard rebot can help... try you can't lose anything ...
Click to expand...
Click to collapse
I mean with this method...
Yakusha said:
I'm curious... let me know if it worked ...
---------- Post added at 08:00 PM ---------- Previous post was at 07:58 PM ----------
I mean with this method...
Click to expand...
Click to collapse
This method didn't work, I will try the esl option next. I tried it before tho with no success, maybe because I didn't install the qualcomm driver. What could be the problem if my phone still doesn't get recognized?
It's so weird that a software issue causes my phone to not be able to connect to my computer on the recover layer
Try this:. Go in twrp - advanced - terminal - and write reboot edl in the terminal and after that flash the official MIUI rom.... try and let me know...
---------- Post added at 09:00 PM ---------- Previous post was at 08:44 PM ----------
bCid_diCb said:
This method didn't work, I will try the esl option next. I tried it before tho with no success, maybe because I didn't install the qualcomm driver. What could be the problem if my phone still doesn't get recognized?
It's so weird that a software issue causes my phone to not be able to connect to my computer on the recover layer
Click to expand...
Click to collapse
Don't open the phone...
Yakusha said:
Try this:. Go in twrp - advanced - terminal - and write reboot edl in the terminal and after that flash the official MIUI rom.... try and let me know...
---------- Post added at 09:00 PM ---------- Previous post was at 08:44 PM ----------
Don't open the phone...
Click to expand...
Click to collapse
if i type reboot edl in the terminal of twrp, my phone goes into a bootloop, showing the mi.com logo, my computer doesnt recognize anything sadly
Did you try to decrypt in twrp with your account's password?
Yakusha said:
Did you try to decrypt in twrp with your account's password?
Click to expand...
Click to collapse
How to do it?
Yakusha said:
Did you try to decrypt in twrp with your account's password?
Click to expand...
Click to collapse
There is nothing left to decrypt I think. How to do it though(for the next time things go wrong)?
bCid_diCb said:
There is nothing left to decrypt I think. How to do it though(for the next time things go wrong)?
Click to expand...
Click to collapse
With the official rom encrypted when you boot in twrp it ask your password for decrypt... But if you bot in twrp and it don't ask anything then you don't have anything to decrypt...
Try to check the others threads...
I'm pretty sure that you can fix it without open it...
Mouths ago I solved a hard brick on my pixel 2xl that was without fastboot, twrp and pc didn't recognize it... I used a tool for reinstall usb drivers and official rom... I will try to find the guide and send it to you as information...
---------- Post added at 04:24 PM ---------- Previous post was at 03:53 PM ----------
How Windows see you device?... Try to go in device manager and check... if your phone appears in device manager as "QHSUSB_BULK" or unknow device, you have to install the proper driver....
And try this tool https://forum.xda-developers.com/android/software/tool-tool-one-driversunlocktwrpfactory-t3358711
So I tried a lot of things, reboot edl didn't work, Testpoint short-circuit didn't work either.
It's hard to say, but I don't know what happened and I have to say goodbye to my beloved phone. It drives me crazy that I didn't found what happened. I don't even know, if I will flash my next phone.
Thanks for your support, if you want to try your luck, or need a display (2weeks old) or any other part, just pm me.
:crying:
bCid_diCb said:
So I tried a lot of things, reboot edl didn't work, Testpoint short-circuit didn't work either.
It's hard to say, but I don't know what happened and I have to say goodbye to my beloved phone. It drives me crazy that I didn't found what happened. I don't even know, if I will flash my next phone.
Thanks for your support, if you want to try your luck, or need a display (2weeks old) or any other part, just pm me.
:crying:
Click to expand...
Click to collapse
Did you try XiaoMiToolV2 ? When you have all drivers, type in program "my phone is bricked", the program should recognize the phone (turning on in twrp) running in recovery and forcing to fastboot mode.
crt-shadow said:
Did you try XiaoMiToolV2 ? When you have all drivers, type in program "my phone is bricked", the program should recognize the phone (turning on in twrp) running in recovery and forcing to fastboot mode.
Click to expand...
Click to collapse
"No devices found[...]"

Categories

Resources