Is anyone able to run TWRP on P580 running Oreo?
Im having problems with my Tab stuck on a black screen instead of recovery mode.
Please help.
Thanks!!
I found a solution if you don't need TWRP, only Magisk or Root. (Using sm-p580 german version P580KXU1CRJ7)
Short Version:
Install Magisk without TWRP with odin in AP section(google it)
Problem is: Once booted up it will tell you that you have to reset your device because the system recognizes that you modified something.
Solution: Just click on the reset button( Magisk will still be there afterwards).
Long Version
Flash the Oreo firmware onto your device.
Set it up (turn on USB debugging) (or dont, I believe you dont need it for download mode ?)
Unzip the AP part of the firmware you have flashed. You may need a modified version of 7-zip, I needed it, because it couldn't unzip lz4.
Google mcmilk 7 zip and download the github release (I hope I'm allowed to reference it, CREDIT goes to MILKY)
You need the boot.img.
Now install Magisk Manager apk.
Under its settings check " .img.tar" under "return of patched boot-images" (Something like that, mine is german)
Click on install in Magisk Manager apk.
Select make thing with boot img, use the boot.img you have extracted and copied onto your phone.
Magisk will create new patched boot img automatically, copy the finished one u find under your main storage in downloads to your pc.
Go into download mode and flash new boot.img with odin using the AP tab.
Now do the things I described in the Short Version
Afterwards install Magisk Manager Apk.
You need internet connection, because it will prompt you to allow installing additional stuff.
A message from some Security App will appear, that something is wrong.
And your device will get laggy and restart.
After that the lag will disapear
I like to use Bk disabler to remove bloatware/ other stuff to flash or back up your device
(Please dont remove any of the 3 phone apks, on Nougat it worked to remove two of them, but oreo will continuously give an error message <- I found out that you can uninstall two of them, but dont uninstall the storagedial-programm thats what gives the errormessage.)
Hope it will help you!
Worked !!!
Thank you dear. Its worked for mine in p585 oreo android....
Anyone can search mcmilk 7zip in google and download program to extract boot.img.lz4 and get boot.img :good:
use the last TWRP for Oreo.
old version makes black screen or red stripes.
go in download-mode (power+home+vol-) and install the last TWRP over with Odin.
for Oreo use the last Odin 3.13
it tested, i had the same problem :fingers-crossed:
Latest twrp dose not worked on my device but this solution work fine
I can confirm that this method does work. I used it on my SM-P580 yesterday. I would suggest that you first backup your all of your apps, contacts, photos, etc using SmartSwitch. You will need to restore everything after the tablet tells you that it needs to be reset because it wipes everything. After the restore, you will need to enter all of your accounts and passwords again but at least all of the data will be back.
amosdinh said:
I found a solution if you don't need TWRP, only Magisk or Root. (Using sm-p580 german version P580KXU1CRJ7)
Short Version:
Install Magisk without TWRP with odin in AP section(google it)
Problem is: Once booted up it will tell you that you have to reset your device because the system recognizes that you modified something.
Solution: Just click on the reset button( Magisk will still be there afterwards).
Long Version
Flash the Oreo firmware onto your device.
Set it up (turn on USB debugging) (or dont, I believe you dont need it for download mode ?)
Unzip the AP part of the firmware you have flashed. You may need a modified version of 7-zip, I needed it, because it couldn't unzip lz4.
Google mcmilk 7 zip and download the github release (I hope I'm allowed to reference it, CREDIT goes to MILKY)
You need the boot.img.
Now install Magisk Manager apk.
Under its settings check " .img.tar" under "return of patched boot-images" (Something like that, mine is german)
Click on install in Magisk Manager apk.
Select make thing with boot img, use the boot.img you have extracted and copied onto your phone.
Magisk will create new patched boot img automatically, copy the finished one u find under your main storage in downloads to your pc.
Go into download mode and flash new boot.img with odin using the AP tab.
Now do the things I described in the Short Version
Afterwards install Magisk Manager Apk.
You need internet connection, because it will prompt you to allow installing additional stuff.
A message from some Security App will appear, that something is wrong.
And your device will get laggy and restart.
After that the lag will disapear
I like to use Bk disabler to remove bloatware/ other stuff to flash or back up your device
(Please dont remove any of the 3 phone apks, on Nougat it worked to remove two of them, but oreo will continuously give an error message <- I found out that you can uninstall two of them, but dont uninstall the storagedial-programm thats what gives the errormessage.)
Hope it will help you!
Click to expand...
Click to collapse
Im not sure if this post belongs here, you link to the T580 TWRP, not the P580.
Is that one compatible with P580?
nill3bor said:
use the last TWRP for Oreo.
old version makes black screen or red stripes.
go in download-mode (power+home+vol-) and install the last TWRP over with Odin.
for Oreo use the last Odin 3.13
it tested, i had the same problem :fingers-crossed:
Click to expand...
Click to collapse
If I do this, will I be able to mount my SD Card as internal storage? 16gb just isnt enough on this tablet.
Do you have to be on oreo already for this to work I'm still on 7.0 and with my system modified I can't upgrade normally
This method root my P585 device but the sim card not working anymore until I odin official rom
also twrp-3.2.3-4-gtaxllte-OMNI6 not work and freeze on Samsung logo
there is no method to root android Oreo P585 Realllllly????
khatkhatik said:
This method root my P585 device but the sim card not working anymore until I odin official rom
also twrp-3.2.3-4-gtaxllte-OMNI6 not work and freeze on Samsung logo
there is no method to root android Oreo P585 Realllllly????
Click to expand...
Click to collapse
This one worked for me on a P585Y. You just have to skip the steps below.
A message from some Security App will appear, that something is wrong.
And your device will get laggy and restart.
After that the lag will disapear
Click to expand...
Click to collapse
It will also show on the Device Maintenance, just ignore the warning.
You can freeze some of the system apps to prevent it from showing on the notification again.
amosdinh said:
I found a solution if you don't need TWRP, only Magisk or Root. (Using sm-p580 german version P580KXU1CRJ7)
Short Version:
Install Magisk without TWRP with odin in AP section(google it)
Problem is: Once booted up it will tell you that you have to reset your device because the system recognizes that you modified something.
Solution: Just click on the reset button( Magisk will still be there afterwards).
Long Version
Flash the Oreo firmware onto your device.
Set it up (turn on USB debugging) (or dont, I believe you dont need it for download mode ?)
Unzip the AP part of the firmware you have flashed. You may need a modified version of 7-zip, I needed it, because it couldn't unzip lz4.
Google mcmilk 7 zip and download the github release (I hope I'm allowed to reference it, CREDIT goes to MILKY)
You need the boot.img.
Now install Magisk Manager apk.
Under its settings check " .img.tar" under "return of patched boot-images" (Something like that, mine is german)
Click on install in Magisk Manager apk.
Select make thing with boot img, use the boot.img you have extracted and copied onto your phone.
Magisk will create new patched boot img automatically, copy the finished one u find under your main storage in downloads to your pc.
Go into download mode and flash new boot.img with odin using the AP tab.
Now do the things I described in the Short Version
Afterwards install Magisk Manager Apk.
You need internet connection, because it will prompt you to allow installing additional stuff.
A message from some Security App will appear, that something is wrong.
And your device will get laggy and restart.
After that the lag will disapear
I like to use Bk disabler to remove bloatware/ other stuff to flash or back up your device
(Please dont remove any of the 3 phone apks, on Nougat it worked to remove two of them, but oreo will continuously give an error message <- I found out that you can uninstall two of them, but dont uninstall the storagedial-programm thats what gives the errormessage.)
Hope it will help you!
Click to expand...
Click to collapse
this works great! thanks!
2 side notes on the process:
1. Magisk no longer provides " .img.tar" patched files, so a tool like "Tar-tool" is required to convert the file from the ".img" type. The patched file should be renamed "boot.img" before conversion in order to be succesfully flashed by Odin.
2. like f4vr said, freeze the apps that give the error notification or just disable the specific notification. Hiding them in Magisk Hider does not seem to work
Cheers, and thanks again for the guide!
Hello Gyus,
I managed to root the device with the method posted by @amosdinh (Thank you so much). Now I'm trying to configure adoptable storage. So far I didn't achieve this goal. ADB commands doesn't work and I can't install the ASPlugin.zip needed by Root Essentials to set adoptable storage by the app.
TWRP for P585 is corrupted, gives blue/red lines screen. The dev that maintains the code is absent since march. I'm out of luck on this. If anyone have a idea to get adoptable storage on this device while using Oreo, please comment.
Thanks!
---------- Post added at 11:17 AM ---------- Previous post was at 11:11 AM ----------
artaeun said:
this works great! thanks!
2 side notes on the process:
1. Magisk no longer provides " .img.tar" patched files, so a tool like "Tar-tool" is required to convert the file from the ".img" type. The patched file should be renamed "boot.img" before conversion in order to be succesfully flashed by Odin.
2. like f4vr said, freeze the apps that give the error notification or just disable the specific notification. Hiding them in Magisk Hider does not seem to work
Cheers, and thanks again for the guide!
Click to expand...
Click to collapse
Just renaming magisk_patched.img to boot.img and adding to .tar file by 7zip worked for me.
We should ask a dev to update twrp for android 8.1
khatkhatik said:
This method root my P585 device but the sim card not working anymore until I odin official rom
also twrp-3.2.3-4-gtaxllte-OMNI6 not work and freeze on Samsung logo
there is no method to root android Oreo P585 Realllllly????
Click to expand...
Click to collapse
Same freeze for me with the Omni - can't do anything outside of access download mode
Same Problem
cmzizi said:
Is anyone able to run TWRP on P580 running Oreo?
Im having problems with my Tab stuck on a black screen instead of recovery mode.
Please help.
Thanks!!
Click to expand...
Click to collapse
I have the same problem. It just keep getting to the bad TWRP, it seems that it does not work with the SM-P580. I had to flash stock firmware to get it back to work.
luinkazofeifa said:
I have the same problem. It just keep getting to the bad TWRP, it seems that it does not work with the SM-P580. I had to flash stock firmware to get it back to work.
Click to expand...
Click to collapse
Really wish this wasn't the case. I'd actually keep this thing if it had a working TWRP.
On my SM-P580 I used Odin and TWRP I don't get the black screen but when I reboot to get into TWRP recovery mode it shows the padlock and says swipe to unlock. Tried many times bit cannot swipe and cannot get past this. All I want is to be able to use the SD card as internal storage. HELP???? Thanks!!
luinkazofeifa said:
I have the same problem. It just keep getting to the bad TWRP, it seems that it does not work with the SM-P580. I had to flash stock firmware to get it back to work.
Click to expand...
Click to collapse
thanks in advanced
where can i find stock firmware?
I've just installed magisk using TWRP via command line. P580
I've just installed magisk using TWRP via command line.
Read the entire post before trying this yourself.
I installed the latest TWRP, the one that bugs and doesn't display anything, this allows to root without wiping data. I'm running the latest korean firmware for P580.
Just do this:
1. Launch TWRP and INMEDIATELY LOCK YOUR SCREEN. (I got ghost stripes that disappeared after 2 days when testing this, work with low light so you can notice your screen whenever it tuens on) Please don't forget this point, don't [temporarily] damage your screen as I did.
2. adb push Magisk-v[Current version].zip external_sd
3. adb shell
4. twrp install external_sd/Magisk-v[Current version].zip
After this you just need to install MagiskManager-v[Current version].apk and you will be all done.
But there is one thing...
If you ever get into recovery mode, there is no way out without using adb as far as I know. You can launch download mode and cancel it but you'll boot back to TWRP.
When in twrp touching your screen or any button will wake the device up and will start burning the ghost image to your screen.
So if you know of a method for rebooting to system without using adb, please let me know.
Also a solution for this would be to flash back the stock recovery, wich may or may not force to wipe system, that something that needs to be tested tho.
Update: Ok so, you can use a handy tool called MTKroot on recovery.img.lz4 to get recovery.img, then use 7z to pack it into a tar file and flash that tar file with odin (AP, same as TWRP)
This way you will not have a 0.001% chance of random boot into recovery mode and damage your screen
Related
How to root Lenovo TAB A7-40 A3500-FL?
[Solved] See the guide below!
Device info:
Model number: Lenovo A3500-FL
Android version: 4.4.2
Kernel version: 3.4.67
Build number: A3500FL_A442_01_25_140823_SE
BB Chip: MT6582
MS Board. A3500FL
Bar code: this was my device's serial number
SW Ver.: ALPS.KK1.MP1.V2.10
Custom Build Verno.: 1408775889
Managed to get cwm and root with this guide: http://forum.xda-developers.com/and...vo-a3500-h-t2879208/post55491817#post55491817
Modified the guide for Lenovo A3500-FL!
EDIT: Also some users have reported that this guide doesn't do the trick or is out-dated, so copypasted the guide from this post here.
Guide
1. Download attachment cwmRecovery.zip and download latest Flash_tool (version 5.1352.0) can be downloaded from here)
1.1. Enable USB-debugging. (How to do this)
2. Manually install the drivers from the attachment a7_40_drivers.zip for the LenovoTablet before plugin it to computer (win7 dirvers work for win8 too).
2.1. To install unsigned/uncertified drivers on Windows 7: http://en.kioskea.net/faq/3914-windows-7-how-to-install-unsigned-drivers
2.2. To install unsigned/uncertified drivers on Windows 8: http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/
2.3. After you have disabled the driver signature verification, you can install the drivers like this: Right click My computer, Manage, Device Manager, right click your computer at the top, Add Legacy hardware, next, Install plapla manually, next, Show all Devices, Have a Disk.., Browse to the driver folder where you unzip them, choose example windows7 and the 64 version (win7 drivers work for win8.x too), install every device. Then follow the guide.
(Note: Otherwise Windows only installs the normal automatic drivers and its more difficult to install the other drivers.)
2.4. Plug your device to PC.
3. Download the latest supersu zip file (version 2.46) from attachments or from https://download.chainfire.eu/696/SuperSU/
3.1. Move the zip.-file to the Sdcard.
4. Turn off your device.
5. Unpack cwmRecovery.zip
6. Run Flash_tool.exe with Admin Rights.
7. Chose Scatter-Loading and choose MT6582_Android_scatter.txt (in Recovery folder).
7.1. Now you will see checekd only one checkbox - recovery, if not click on it and choose recovery.img
7.2. Press Download.
7.3. Connect your device.
7.4. Wait few seconds.
8. Have CWM on your device .
9. Unplug your device.
10. . Boot to cmw recovery by turning off your device. Then press and hold VOL DOWN + VOL UP and then also press and hold POWER for about 7 seconds.
10.1. Choose " Install zip from sdcard." (To confrim always use the Power Button)
10.2. Choose "zip from sdcard".
10.3. Select SuperSU-v2.46.zip from sdcard and apply.
10.4. Have a rooted tablet.
It might be necessary to always flash the CWM with the Flashtool directly before you startup the device. Otherwise it will start the original AndroidRecovery again.
It might also be necessary to use different drivers from here.
If the supersu zip doesn't install, try toggling the signature verification to disabled from cwm->install zip from sdcard->toggle signature verification.
Tested and working on Levono A7-40 3500-FL with kitkat update, build number A3500FL_A442_01_25_140823_SE, from ota. Attached screenshot for proof. Also other people have reported that this works for later updates too, for example A3500FL_A442_01_27_141127_SE.
You can update to the latest OTA firmware by first going back to stock recovery. See the second post for the guide.
Thanks and credits go to: @Koli96 and @bobais
How to go back to stock rom/recovery and update to latest Lenovo OTA firmware update
So, it's pretty simple, you take the stock_recovery.zip from the first post, extract it, and replace recovery.img in the recovery folder with the stock one.
Then :
Quote:
4. Turn off your device.
6. Run Flash_tool.exe with Admin Rights
7. Chose Scatter-Loading and choose MT6582_Android_scatter.txt (in Recovery folder)
7.1. Now you will see checekd only one checkbox - recovery, if not click on it and choose recovery.img
7.2.. Press Download
7.3. Connect your device
7.4. Wait few seconds.
And that's it !
On a side note, if it seems stuck on a black screen with a loading circle after factory reset, you have to put the tablet in landscape mode and restart (the shutdown menu appears without any problem) - this issue doesn't seem related to recovery, but a bug within lenovo firmware and the first configuration screen.
Side note 2: The first boot after flashing new update might take 15mins.
Side note 3: After updating to the latest OTA you can go back to cwm recovery with the guide from the first post.
Credits @tenuis
I got the same tablet and I also am looking for a root. :/
Another waiting for rooting lenovo owner.
Same here, i was looking for a root guide and i couldn't find anything.
Does anyone else has a problem with long charging times?
Well it charges long and the charge stays long, so no issue here.
Seems that not that many lenovos root easily, but of course this is a pretty new device(?).
leripe said:
Well it charges long and the charge stays long, so no issue here.
Seems that not that many lenovos root easily, but of course this is a pretty new device(?).
Click to expand...
Click to collapse
OK let's try this
Install mtk drivers
Install USB and adb drivers
Install v root 1.7.8
Now tick adb debugging and connect your device to PC run v root and click root button after device get connected to v root
Let me know if you have any issues
All the best ?
Sent from my x604 using Tapatalk
The-Immortal said:
OK let's try this
Install mtk drivers
Install USB and adb drivers
Install v root 1.7.8
Now tick adb debugging and connect your device to PC run v root and click root button after device get connected to v root
Let me know if you have any issues
All the best ?
Sent from my x604 using Tapatalk
Click to expand...
Click to collapse
Can you link all the drivers?
Edit: Vroot link here: http://vrootdownload.info/vroot1.7.8/
leripe said:
Can you link all the drivers?
Edit: Vroot link here: http://vrootdownload.info/vroot1.7.8/
Click to expand...
Click to collapse
If you have win7 or win8/8.1 USB drivers will automatically installed when you connect device
Adb driver I hope this will work
http://adbdriver.com/downloads/
If it fails make a google search am sure you will find it
Sent from my x604 using Tapatalk
The-Immortal said:
If you have win7 or win8/8.1 USB drivers will automatically installed when you connect device
Adb driver I hope this will work
http://adbdriver.com/downloads/
If it fails make a google search am sure you will find it
Sent from my x604 using Tapatalk
Click to expand...
Click to collapse
Installed everything and tried vroot once again (I have tried it before).
Still not rooted. And btw that vroot at least tries to install bunch of bloatware crap on the pc.
Edit:
I would suggest for anyone who installed Vroot to your pc to scan the whole pc after you uninstall the vroot.
Here are the scanning tools:
Malwarebytes
adwcleaner
superantispyware
hitmanpro
leripe said:
Installed everything and tried vroot once again (I have tried it before).
Still not rooted. And btw that vroot at least tries to install bunch of bloatware crap on the pc.
Edit:
I would suggest for anyone who installed Vroot to your pc to scan the whole pc after you uninstall the vroot.
Here are the scanning tools:
Malwarebytes
adwcleaner
superantispyware
hitmanpro
Click to expand...
Click to collapse
I got a successful root by flashing Recovery.rar from lenovo-forums.ru, (it's easy to google, I'm not allowed to post links) with the included SPFlash Tool and afterwards flashing the needed SU binaryies and apk. However, this will mess up the OTA updates, and I can't find the stock recovery again.
Therefore, I really beg anyone having the stock recovery to post it, enabling us to switch between them, whenever we want to apply any OTAs.
Thanks a lot!
nkr said:
I got a successful root by flashing Recovery.rar from lenovo-forums.ru, (it's easy to google, I'm not allowed to post links) with the included SPFlash Tool and afterwards flashing the needed SU binaryies and apk. However, this will mess up the OTA updates, and I can't find the stock recovery again.
Therefore, I really beg anyone having the stock recovery to post it, enabling us to switch between them, whenever we want to apply any OTAs.
Thanks a lot!
Click to expand...
Click to collapse
Well I very highly doubt that there will be any more updates for a device with this price range. And since the next android version is the L version, which requires more work than before.
Edit2: http://forum.xda-developers.com/android/development/guide-lenovo-a3500-h-t2879208 found this. Tested and it works. Will edit it to the first post.
The same as me
i cant flash update.zip from cwm recovery and need to restore the stock recovery ...
I think flashing the stock rom can solve the problem..
.by using the sp flash tool we can select to flash recovery only ....unticking the others except recovery.img ....you just try to download the stock rom and flash the recovery
Same problem
Heya guys!
I have the same problem here.. I can't run the .zip file from the SD card, it get interrupted every time. Any ideas?
drabuaiad said:
The same as me
i cant flash update.zip from cwm recovery and need to restore the stock recovery ...
I think flashing the stock rom can solve the problem..
.by using the sp flash tool we can select to flash recovery only ....unticking the others except recovery.img ....you just try to download the stock rom and flash the recovery
Click to expand...
Click to collapse
I dont know what you two are trying to do but this thread is about rooting the lenovo A3500-FL not about lenovo stock rom.
Rooting..
Yes indeed, that's what I'm trying to do. Rooting the A3500-FL. According to the instructions you need to install the SuperSU from a zip on your SD card. When I try do that it gets interrupted every time. Installing recovery went well. So I'm not getting what I do wrong? Any ideas?
leripe said:
I dont know what you two are trying to do but this thread is about rooting the lenovo A3500-FL not about lenovo stock rom.
Click to expand...
Click to collapse
Mrosenho said:
Yes indeed, that's what I'm trying to do. Rooting the A3500-FL. According to the instructions you need to install the SuperSU from a zip on your SD card. When I try do that it gets interrupted every time. Installing recovery went well. So I'm not getting what I do wrong? Any ideas?
Click to expand...
Click to collapse
http://download.chainfire.eu/452/SuperSU/UPDATE-SuperSU-v2.02.zip and y ou mean this when you talk about update.zip?
And I hope you are using the install zip from sdcard option and the choose zip from sdcard option?
Boot to cmw.
Install zip from sdcard.
Choose zip from sdcard.
browse to your supersu zip and apply.
Now I also update the first post's guide, so you can check that out too.
Thanks for the help so far. But now I'm starting to doubt that the CWM install went successfully. Let me show you a picture of my screen after a failed install of the UPDATE-SuperSU-v2.02.zip -file. (ht_tps://ww_w.dropb_ox.com/s/1wrnatzjk2gn42h/2014-10-09%2008.50.40.png?dl=0) (slightly modified link because of forum rules, just take out the _) I'm using the "apply update from sdcard" option, then I browse to the SuperSU.zip -file and apply it. Then it starts installation, but aborts it in a few seconds. So am I booting to just a normal recovery mode and not CWM? (Sorry if all this seems totally ignorant, I have only flashed roms before, never rooted a new device)
leripe said:
UPDATE-SuperSU-v2.02.zip and you mean this when you talk about update.zip?
And I hope you are using the install zip from sdcard option and the choose zip from sdcard option?
Boot to cmw.
Install zip from sdcard.
Choose zip from sdcard.
browse to your supersu zip and apply.
Now I also update the first post's guide, so you can check that out too.
Click to expand...
Click to collapse
Yup.. This is the problem. The recovery runs fine from Flash Tool and claims it installs it. (Download ok) But I still don't seem to have CWM on the device. It's just normal recovery mode. So any ideas about the CWM-installation? What could possibly go wrong? I get no error messages. Cheers.
//Mike
Mrosenho said:
Thanks for the help so far. But now I'm starting to doubt that the CWM install went successfully. Let me show you a picture of my screen after a failed install of the UPDATE-SuperSU-v2.02.zip -file. (ht_tps://ww_w.dropb_ox.com/s/1wrnatzjk2gn42h/2014-10-09%2008.50.40.png?dl=0) (slightly modified link because of forum rules, just take out the _) I'm using the "apply update from sdcard" option, then I browse to the SuperSU.zip -file and apply it. Then it starts installation, but aborts it in a few seconds. So am I booting to just a normal recovery mode and not CWM? (Sorry if all this seems totally ignorant, I have only flashed roms before, never rooted a new device)
Click to expand...
Click to collapse
thanks ...
It is work fine for me on a3500 fl with 4.4.2 ver a442_01_26_140911_se
Mrosenho said:
Yup.. This is the problem. The recovery runs fine from Flash Tool and claims it installs it. (Download ok) But I still don't seem to have CWM on the device. It's just normal recovery mode. So any ideas about the CWM-installation? What could possibly go wrong? I get no error messages. Cheers.
//Mike
Click to expand...
Click to collapse
Same for me, what about this @leripe ?
EDIT// Oh, It's working now, tried to flash it one more time, then I held a power button until Lenovo logo appeared and then I pressed Vol UP and Vol DOWN and the CWM came in, thank you! Now my tablet is finally rooted
Hello guys.
I have successfully ported TWRP 3.0.0-0 for our Smart Prime 6.
It's 100% working !!
There are NO BUGS !! :good:
DOWNLOAD
NEW LINK: DOWNLOAD
________________________________________
How to install
Via app:
1) Download TWRP 3.0.0-0 from the link above and place it on internal storage of your phone.
2) Download Flashify app from Google Play Store.
3) Open Flashify app.
4) Grant root permissions.
5) Click "Recovery image" and then click "Choose a file"
6) Navigate to the folder where you placed TWRP 3.0.0-0 and choose the .IMG file.
7) Press "Yup!" button and wait.
8) After a while the phone will require reboot. So click "reboot" button.
9) Phone will reboot and automatically boot into TWRP, so you can press reboot to system.
10) Enjoy!
Special thanks to Oneb1t for modded .fstab file! :highfive:
edit: you can use Flashfire app too instead of Flashify, but it's not recommended, because the latest version of the Flashfire app is not flashing properly.
Brilliant! Thank you so much! Do you know any custom ROM what is better than the factory ROM?
There is no custom ROM for this phone yet.
But I'm trying to make LITE ROM.
Adreno306™ said:
There is no custom ROM for this phone yet.
But I'm trying to make LITE ROM.
Click to expand...
Click to collapse
Do you think it's easier/possible to adapt a ROM from a similar device like say, the Alcatel
Pop 2 (5) Premium ? I don't know if there's any ROM for that phone tho, but since it's branded as Alcatel you might get more support from the community here than by using Vodafone's name.
Hello, Demonlord6.
I have tried to make a stock flashable ROM via dumping the system folder and the boot.img file, but without success.
It does not boot properly.. when I tried to flash it without dalvik/system wipe everything was as before.
When I tried to wipe /system and dalvik first and then flash the ROM, it causes bootloop.
So now I'm trying to fix this issue..
I don't know where the problem is.
So when this issue will be solved I will try to build a ROM from Alcatel phones with same specs.
Adreno306™ said:
Hello, Demonlord6.
I have tried to make a stock flashable ROM via dumping the system folder and the boot.img file, but without success.
It does not boot properly.. when I tried to flash it without dalvik/system wipe everything was as before.
When I tried to wipe /system and dalvik first and then flash the ROM, it causes bootloop.
So now I'm trying to fix this issue..
I don't know where the problem is.
So when this issue will be solved I will try to build a ROM from Alcatel phones with same specs.
Click to expand...
Click to collapse
Hey, Andreno306
I don't know much about Rom's in that level of expertise I'm afraid :/ but I did some digging and came across this simple tutorial on XDA:
http://forum.xda-developers.com/showthread.php?t=2387941
I imagine it does not work for every single device out there, at least not with modifying stuff after, but it might be a good starting point I think, in fact I would try to actually make one myself had I a working PC currently at home. But even if I did I had no way of testing it because this is currently my daily driver phone.
Just wanted to say that I'm also very interested in getting a slim ROM for this device. I can't offer any expertise I'm afraid! Just wanted to show that there are people interested in your project.
:highfive:
Stock Kernel
Thanks, it works great.
This is little off-topic but does anyone has the stock kernel, i flashed NeoKernel but it is not that good and i forgot to make a backup do can anyone please link me to the stock kernel?
vojta_horanek said:
Thanks, it works great.
This is little off-topic but does anyone has the stock kernel, i flashed NeoKernel but it is not that good and i forgot to make a backup do can anyone please link me to the stock kernel?
Click to expand...
Click to collapse
I have one
https://mega.nz/#!tMJD3B4T!f6m2ELYCVupqGCcN2aGbkrNzEqijLu7au-7usEfeVL0
But I recommend to restore it with the flashify app, because that's how the backup was made.
If, for some reason, you don't/can't restore it, then you can always try Sugar on the PC which basically restores everything to factory settings (recovery, kernel, etc, it all gets reset)
Demonlord6 said:
I have one
But I recommend to restore it with the flashify app, because that's how the backup was made.
If, for some reason, you don't/can't restore it, then you can always try Sugar on the PC which basically restores everything to factory settings (recovery, kernel, etc, it all gets reset)
Click to expand...
Click to collapse
Restored and my phone keeps turning off after boot(once i saw the turn off screen, other times it just vibrates at boot screen), isnt it the wrong file? (flashed wia flashify)
I was able to restore the boot from TWRP (lucky i made a backup this time)
vojta_horanek said:
Restored and my phone keeps turning off after boot(once i saw the turn off screen, other times it just vibrates at boot screen), isnt it the wrong file? (flashed wia flashify)
I was able to restore the boot from TWRP (lucky i made a backup this time)
Click to expand...
Click to collapse
Sorry there about the bootloop but glad u could restore it from TWRP, maybe it was because we have different ROM versions ?
Demonlord6 said:
Sorry there about the bootloop but glad u could restore it from TWRP, maybe it was because we have different ROM versions ?
Click to expand...
Click to collapse
I got this one: http://www.needrom.com/download/vodafone-smart-prime-6-vf-895n-debloatedclean-stock/#
vojta_horanek said:
I got this one: http://www.needrom.com/download/vodafone-smart-prime-6-vf-895n-debloatedclean-stock/#
Click to expand...
Click to collapse
Yeap, that's not the same version as my ROM, mine is not 130FNN etc. Maybe that's why it didn't work
Enviado do meu GT-S5280 através de Tapatalk
Sorry for the stupid question but... does it works on Smart Prime 7 too?
Has anyone installed that linked ROM? It seems to be what we are looking for... a slim debloated rom.
I presume we need to be rooted, install this TWRP, then flash that ROM?
It mentions unlocking the bootloader, I dont think I've seen any info anywhere about unlocking the bootloader.
Can anyone give a quick lowdown on all the steps required to install that ROM please?
Hi everyone, I discovered that Elephone Trunk and Smart Prime 6 have (almost) identical specs: https://www.devicespecifications.com...ison/c584481c6
So it would be great to "port" (or build ?) the official Nougat-OmniROM for Trunk to VF-895N: http://dl.omnirom.org/trunk/
Last but not least, here's official Vodafone Smart Prime 6 sources: Vodafone_Smart_prime_6_20150413.tar.xz
TWRP for vodafone smart max 4 990N (coolpad 8890u).
I tried this recovery image for vodafone smart max 4 990N (coolpad 8890u).
The phone is in a bootloop state. I think i have usb debugging enabled already.
So, in fastboot mode i can see the device in my pc in adb fastboot cmd.
Im trying to ''fastboot boot recovery.img" but it stops in ''booting..''.
Dont know whats the problem but for sure i can not find a specific twrp image for this device.
If i enter fastboot oem device-info it says ''(bootloader) Device unlocked: true''.
Any ideas ?
hi i was wondering if you could share how you did this or if you can make one for the Vodafone smart n9 (VFD720) it would help a lot of people out looking for this
Needed to root a Vodafone Smart Prime 6 (VF 895N) (got it from a friend because it became unresponsive from all the updated google play stuff ) to get linux-deploy running. Just wanted to leave a big thank you here for Adreno306 for his TRWP 3.0.0-0. it did the job very well!
Only the procedure to get it installed differed quite a bit for me, since Flashify is no longer available.
I wanted to preserve boot and just flash trwp to recover, what worked quite well.
The first thing I did was to boot the phone manually in recovery mode (Power+Vol up) and reset it to factory settings from there. It takes a little while. Then follow the setup, go to phone settings, enable developer mode and set usb debugging. If "unlock oem" is not available there, reboot into recovery again, set unlock there and reboot into bootloader.
The prerequisites are adb and fastboot, both must work. Means adb devices and fastboot devices must show the phone. What can make problems under win10 as it sometimes does not detect the phone in bootloader mode. An actual google usb driver is needed, as provided by google.
For me adb worked well, but when rebooted into bootloader with adb reboot bootloader, fastboot didnt detect the phone. With the phone still connected, the windows device manager showed an unknown device with and exclamation mark (!). Right click, install driver, select driver manually, select driver from device list, mark all devices (first entry) and click "disk", then point to the usb driver director and select "ADB fastboot driver". ( A more comprehensive description is available here )
Once adb and fastboot detect the device, it is time to prepare it. Boot to system (normal operation) first. Make sure that the TRWP 3.0.0-0.img is renamed to trwp.img and then
adb reboot bootloader
fastboot devices
fastboot oem unlock
fastboot boot trwp.img
Now the phone should show the trwp menu, set it up to root the phone and install SuperSU. Reboot into bootloader and
fastboot flash recovery trwp.img
fastboot reboot
Verify with adb reboot recovery, you should see trwp now. Reboot to system.
Now finally go into the app selector, start SuperSU, and root the phone. SuperSu uses trwp recovery mode to install its image and root is done.
Again, big thanks for providing the TRWP image!
Adreno306™ said:
Hello guys.
I have successfully ported TWRP 3.0.0-0 for our Smart Prime 6.
It's 100% working !!
There are NO BUGS !! :good:
DOWNLOAD
NEW LINK: DOWNLOAD
________________________________________
How to install
Via app:
1) Download TWRP 3.0.0-0 from the link above and place it on internal storage of your phone.
2) Download Flashify app from Google Play Store.
3) Open Flashify app.
4) Grant root permissions.
5) Click "Recovery image" and then click "Choose a file"
6) Navigate to the folder where you placed TWRP 3.0.0-0 and choose the .IMG file.
7) Press "Yup!" button and wait.
8) After a while the phone will require reboot. So click "reboot" button.
9) Phone will reboot and automatically boot into TWRP, so you can press reboot to system.
10) Enjoy!
Special thanks to Oneb1t for modded .fstab file! :highfive:
edit: you can use Flashfire app too instead of Flashify, but it's not recommended, because the latest version of the Flashfire app is not flashing properly.
Click to expand...
Click to collapse
Hi, I would like to try your tutorial but I can't root this phone (which is an important step in the tutorial), is there any way someone could help me??
Thanks
If so, how? Thanks!
magicmanfk said:
If so, how? Thanks!
Click to expand...
Click to collapse
This was totally bugging me too but after a whole day of trying I've finally managed it.
1) Go to this thread here
2) Boot into fastboot and flash the boot.img and system.img as suggested in the thread
3) Also flash the original recovery using "fastboot flash recovery recovery.img"
4) Go to the official asus support site here and download the update files you need, the last two
5) Download Version V11.41.87.2 and place the file in the internal storage of your sd card, once you pull the cable out your phone the phone should detect a update file and ask if you want to install it. Click OK.
6) The phone will unpack the update and reboot and install it
7) Delete this update file and then add the latest Nougat update file (Version V20.31.49.2)
8) Do the same again and install it and there you have it... the key is that you have to install each incremental update rather than go straight to the latest.
Oh and I don't know if it makes any difference, but I decided to turn off adb debugging once I'd flashed the various boot, system and recovery images before I started to update using the Asus method.
Also I have successfully re-flashed TWRP through fastboot on Nougat.
Hope this helps.
worked for me perfectly
pjcarrmole said:
This was totally bugging me too but after a whole day of trying I've finally managed it.
1) Go to this thread here
2) Boot into fastboot and flash the boot.img and system.img as suggested in the thread
3) Also flash the original recovery using "fastboot flash recovery recovery.img"
4) Go to the official asus support site here and download the update files you need, the last two
5) Download Version V11.41.87.2 and place the file in the internal storage of your sd card, once you pull the cable out your phone the phone should detect a update file and ask if you want to install it. Click OK.
6) The phone will unpack the update and reboot and install it
7) Delete this update file and then add the latest Nougat update file (Version V20.31.49.2)
8) Do the same again and install it and there you have it... the key is that you have to install each incremental update rather than go straight to the latest.
Oh and I don't know if it makes any difference, but I decided to turn off adb debugging once I'd flashed the various boot, system and recovery images before I started to update using the Asus method.
Also I have successfully re-flashed TWRP through fastboot on Nougat.
Hope this helps.
Click to expand...
Click to collapse
Thanks for the instructions; worked for me. Were you able to re-root? I tried to by following this guide: https://www.reddit.com/r/zenfone/comments/6gqha5/zenfone_3_ze553kl_z01hd_root/
But on step 8 of the supersu website, my phone gets stuck on "starting adb sideload feature." I had already tried installing supersu via twrp, but still no root.
Devalorize said:
Thanks for the instructions; worked for me. Were you able to re-root? I tried to by following this guide: https://www.reddit.com/r/zenfone/comments/6gqha5/zenfone_3_ze553kl_z01hd_root/
But on step 8 of the supersu website, my phone gets stuck on "starting adb sideload feature." I had already tried installing supersu via twrp, but still no root.
Click to expand...
Click to collapse
I flashed TWRP from one of the other threads on here filename twrp-3.1.0-0-Z01H-20170408.img to be precise.
I then flashed the latest version of magisk the zip found here
Then selecting core files only and magisk hide options I have root that passes the latest safetynet checks. No problem.
pjcarrmole said:
I flashed TWRP from one of the other threads on here filename twrp-3.1.0-0-Z01H-20170408.img to be precise.
I then flashed the latest version of magisk the zip found here
Then selecting core files only and magisk hide options I have root that passes the latest safetynet checks. No problem.
Click to expand...
Click to collapse
This worked for me, thanks. It's too bad Xposed doesn't support Nougat yet. Missing my Xposed modules.
Devalorize said:
This worked for me, thanks. It's too bad Xposed doesn't support Nougat yet. Missing my Xposed modules.
Click to expand...
Click to collapse
Magisk has a few modules for it but nothing like Xposed.
I'm going to do a full back up and then see how well ZenUI plays with Substratum as most of the ZenUI Themes are pretty poor and I want an all black theme. I'll let people know how it goes if anyone is interested in using substratum.
---------- Post added at 10:28 AM ---------- Previous post was at 09:32 AM ----------
pjcarrmole said:
I flashed TWRP from one of the other threads on here filename twrp-3.1.0-0-Z01H-20170408.img to be precise.
I then flashed the latest version of magisk the zip found here
Then selecting core files only and magisk hide options I have root that passes the latest safetynet checks. No problem.
Click to expand...
Click to collapse
Oh, if you're having trouble getting TWRP to stick don't reboot the system but reboot back into Recovery, by holding the Vol - & Power together and using the Volume buttons to select Recovery.
After this you can then reboot normally.
Disclaimer: If you go through with this and encounter issues, I (or the others here) will try to help you, but the risk is all yours.
I see a few posts mentioning TWRP for the AFTV3, so here it is for the pendant (needle): link. Extract twrp.img from the archive, copy it to /sdcard, and flash as follows:
Code:
adb shell
su
dd if=/sdcard/twrp.img of=/dev/block/recovery
Note: You will need a Y (OTG) cable to connect a mouse and/or a keyboard.
I have tested this on the pendant (needle), but it should also work for the cube (stark).
You can also boot or flash this from fastboot (reboot bootloader or run from aml_reboot in the root thread) if you so desire.
To enter recovery from a terminal running on the AFTV3:
Code:
reboot recovery
To enter recovery from ADB:
Code:
adb reboot recovery
For those interested, here's what I did:
-- Rather than build from scratch, I used an existing TWRP for Amlogic's S905X as the base. Quite a few of them are here.
-- You can't just use a random TWRP and expect it to work on the AFTV3 (due to hardware and partition mismatch). I first replaced (and repacked) the ramdisk with that from needle's boot image (using magiskboot).
-- While TWRP booted up, USB OTG was absent. Without OTG, TWRP is not of much use (w/o OTG, I used openrecoveryscript as a workaround). Turns out the random TWRP images lack the correct USB modules. I extracted the correct modules from the AFTV3, copied them to the TWRP image, and everything works.
If something doesn't work, please post here.
Great job, i flashed it from fastboot.
adb reboot bootloader (or install a app that will reboot into bootloader)
fastboot flash recovery C:\(this TWRP version)
Seems to be functional.
the old Firestick 1's you could control the mouse from a adb shell. I dont know how to make that functional for those without a OTG.
Confirmed, it works on the cube (stark) as well...
That's really a great job. As stated here: https://forum.xda-developers.com/showpost.php?p=78958467&postcount=165 I (hopefully soft) bricked my pendant trying to install Google services. Now it just reboot at the white amazon logo. Ordered a OTG cable to test TWRP but was trying random versions. Now this confirmed woirking version is a life saver to me. Now I just have to find a way to remove the offending google service apk.
Thanks again.
Sorry to bother again.
I still have my pendant in bootloop (bad google service installation).
Tried OTG cable but using it doesnt let me go in fastboot mode and I dont know how to navigate in recovery without it.
Since now the pendant is rooted and can recover OTA files maybe my next attempt could be to try to find a .bin rom file and flash it using fastboot?
If so does anyone know if there is such a file yet (pre rooted version should be great)?
Thanks.
Does anyone know where to get the updated firetv3 roms? with TWRP now i would like to attempt updates.
Michajin said:
Does anyone know where to get the updated firetv3 roms? with TWRP now i would like to attempt updates.
Click to expand...
Click to collapse
None available yet, but there are a couple of methods by which we may obtain them.
The first one has some risk involved. you would have to re-enable OTA updates and allow the device the check for and download the current version
and then again disable the OTA update apps. Then pull a copy of the update from the device before clearing the cache.
I have noticed that as long as the device is busy, say running a sideloaded app, it will not initiate a downloaded update.
The second is dependent upon if the individual will help us. There is a member on this forum who has modified the DeviceSoftwareOTA.apk for OS 5
that allowed update check and download to stay enabled because the installation procedure was removed from the APK. So you could simply pull the
update from the cache at any time. I will pull a copy from OS 6 and post it today and see if he would be willing to assist.
I'm with you, I'd like to update mine as well after seeing some of the changes that have been posted.
2WhlWzrd said:
None available yet, but there are a couple of methods by which we may obtain them.
The first one has some risk involved. you would have to re-enable OTA updates and allow the device the check for and download the current version
and then again disable the OTA update apps. Then pull a copy of the update from the device before clearing the cache.
I have noticed that as long as the device is busy, say running a sideloaded app, it will not initiate a downloaded update.
The second is dependent upon if the individual will help us. There is a member on this forum who has modified the DeviceSoftwareOTA.apk for OS 5
that allowed update check and download to stay enabled because the installation procedure was removed from the APK. So you could simply pull the
update from the cache at any time. I will pull a copy from OS 6 and post it today and see if he would be willing to assist.
I'm with you, I'd like to update mine as well after seeing some of the changes that have been posted.
Click to expand...
Click to collapse
Would the update fail anyway if I replaced Amazon recovery with TWRP?
Michajin said:
Would the update fail anyway if I replaced Amazon recovery with TWRP?
Click to expand...
Click to collapse
No, TWRP would be over written by an OTA update.
2WhlWzrd said:
No, TWRP would be over written by an OTA update.
Click to expand...
Click to collapse
you sure about that? i just screwed up and was rooting my "tanks" and forgot to update one. Then i took the update, it ran the amazon update though open recovery TWRP and updated. Booted without issues, i know its a firestick2, but almost thinking i should test on a pendant...
Michajin said:
you sure about that? i just screwed up and was rooting my "tanks" and forgot to update one. Then i took the update, it ran the amazon update though open recovery TWRP and updated. Booted without issues, i know its a firestick2, but almost thinking i should test on a pendant...
Click to expand...
Click to collapse
There is a difference between writing outside of TWRP and with TWRP, it's hard to overwrite something that's doing the writing.
If you read in the first post of the tank rooting thread, the author explicitly states: "Only ever flash boot/recovery images using TWRP",
anything outside of that will not be root aware. Better to be safe, than sorry.
How may I get the "su". It said, I don't have permision.
eSephiroth said:
How may I get the "su". It said, I don't have permision.
Click to expand...
Click to collapse
Open Magisk Manager, Select the Menu in the top left corner.
In the sidebar navigate to "Superuser", you should see "com.android.shell".
Toggle the switch to right to enable it.
2WhlWzrd said:
Open Magisk Manager, Select the Menu in the top left corner.
In the sidebar navigate to "Superuser", you should see "com.android.shell".
Toggle the switch to right to enable it.
Click to expand...
Click to collapse
If you didn't root the device, how can you have superuser?
eSephiroth said:
If you didn't root the device, how can you have superuser?
Click to expand...
Click to collapse
I assumed you were already rooted. Since you are not, start here:
[ROOT] Rooting the FireTV Cube and Pendant with FireFU
Anything from firmware 6.2.5.8 and up, the exploit has been patched.
This is the most complicated root method I have ever seen. Mine is 6.2.8. too bad.
eSephiroth said:
This is the most complicated root method I have ever seen. Mine is 6.2.8. too bad.
Click to expand...
Click to collapse
This isn't the root thread. But yeah, it's the only thing we've got for these devices, so we make it work
Hi,
I was able to recover my Pendant using a finally working OTG cable and using mouse with your TWRP and finally delete the offending google.gsm app so thanks a lot for that.
The only thing I noticed is that adb doesn't work for me once booted into TWRP (I wanted to use adb backup to backup bigger partitions directly to my PC). Is that just my issue or it's happening for everyone?
Thanks.
Pino.
moving it to the right place.
anyone have interest in the update files? If i turn on my update, download the update, but before rebooting copy the .bin file to a different folder, delete from the cache folder then disable updates again. I can share the file if anyone wants it to see if we can modify to keep root and update? I am thinking i might download it, move it and change it to a .zip, then reboot into TWRP. Flash the update and flash magisk before a reboot. Anyone have thoughts about risk of a BRICK?
Hey guys, this is my first post. I just bought a Samsung SM-T510 and would like to unlock all the features. I'm currently trying to follow multiple guides on how to do so. To my understanding, my best bet is lineageOs 16. I've been following https://forum.xda-developers.com/gal...-16-0-t3987317 alongside with https://forum.xda-developers.com/gal...howto-t3989361 and I'm pretty confused on the method order i need to follow. What I mean is do I install rom first, TWRP, Magisk etc.?
More guides ive been following:
https://forum.xda-developers.com/gal...-10-1-t3934805
https://forum.xda-developers.com/app...mless-t3473445
https://topjohnwu.github.io/Magisk/i...system-as-root
I see posts saying I need and don't need Multidisabler so I'm confused on what I actually need: https://forum.xda-developers.com/gal...ption-t3963020
Another one: https://forum.xda-developers.com/gal...ption-t3919714
https://forum.xda-developers.com/gal...eries-t3918699
I have so many tabs open currently; I know I'm missing a few important ones.
So given all that info, i think i have all the software to do this between kernels, rom, twrp, odin, magisk, multi disabler? and i think thats all.
My sm-t510 build number is T510XXU2ASK5, looking through the lineage rom guide, I click the link https://samfrew.com/model/SM-T510/ and i see different versions. I'm honestly completely confused about this file and how I'm going to use it. I understand it to be the stock rom? as in factory software? With TWRP too, the numbers don't match my current build number leaving me very confused.
Do I need to downgrade my build number (i don't know if it's even a thing just asking)?
I think i can do everything relatively easy once I have an understanding of what to do first (order of things) and the specific files for the specific steps. When I'm reading these guides, I honestly have no idea which download goes for what. For ex. going back to https://forum.xda-developers.com/gal...-16-0-t3987317 like what do I need to download, the build number listed in notes regarding kernel or go to the download section right below and use that? Or both and if both, how do I use them separately for there a specific purpose? I cannot find anything that makes me feel comfortable rooting/custom rom on my device. Not comfortable in terms of I don't know what I'm doing exactly. I have put days of reading into this and still, I cannot figure out how to do this. I would really appreciate it if someone could help me. This is stressing me out and I would like to get this done before Monday due to me having some serious surgery. The reason being; I won't be as fresh on everything I've read recently.
I'm sorry if this post is choppy and all over the place. I'm just exhausted and clueless at this point. If I left any info out in order for someone to help me please let me know so I can provide it.
EDIT: The TWRP file ends in build number SK1, the file lineage-16.0-20191019-UNOFFICIAL-T510XXU2ASI4.tar.md5 doesn't match the TWRP file as well as my current build number; which ends in SK5. So nothing is matching the 3 last characters in my build number across all guides besides the samfrew link.
Also, I keep seeing i need a .tar TWRP file for recovery (?) but when I unzip both files are .img (named boot/recovery)
You don’t unzip the .tar files. Keep them as is.
secretwolf98 said:
You don’t unzip the .tar files. Keep them as is.
Click to expand...
Click to collapse
I don't get a .tar file until I unzip the folder; I get a filed with .tar.md5
My recommendation would be to first upgrade to T510XXS2ASK1 of the OEM firmware, since that's the latest version for which Samsung has published kernel source. Use the latest release of Odin and install BL, AP and HOME_CSC. After this, unlock the bootloader and prevent VaultKeeper from relocking it by always enabling Debugger Options while connected to the Internet after a factory wipe.
From there, you could just install TWRP, install the latest MultiDisabler, and live with the Samsung firmware. You could even install Magisk to root. However, I prefer a clean Google OS without all the OEM bloatware, so I'd recommend installing the latest Nexus Stock (which includes TWRP and the custom kernel that disables Knox boot security features). Again, use Odin and install it to AP and do a factory wipe in TWRP because file-based encryption is still unsupported on these custom ROMs.
You could install LineageOS instead, but I haven't yet updated that for T510XXS2ASK1. I've just been busy and Andy hasn't been releasing any new LineageOS 16 GSIs. We're also pretty close to releasing a LineageOS 17 build.
fountainb234 said:
I don't get a .tar file until I unzip the folder; I get a filed with .tar.md5
Click to expand...
Click to collapse
Just rename the file cutting off the .md5.
is it possible to downgrade from sk5 to sk1? you cannot upgrade to a later version, and I know downgrading can have reverse effects on the tablet. I have same tablet I would like to know. if I flash sk1 is there a way to fix it if it bricks?
Magendanz said:
My recommendation would be to first upgrade to T510XXS2ASK1 of the OEM firmware, since that's the latest version for which Samsung has published kernel source. Use the latest release of Odin and install BL, AP and HOME_CSC. After this, unlock the bootloader and prevent VaultKeeper from relocking it by always enabling Debugger Options while connected to the Internet after a factory wipe.
From there, you could just install TWRP, install the latest MultiDisabler, and live with the Samsung firmware. You could even install Magisk to root. However, I prefer a clean Google OS without all the OEM bloatware, so I'd recommend installing the latest Nexus Stock (which includes TWRP and the custom kernel that disables Knox boot security features). Again, use Odin and install it to AP and do a factory wipe in TWRP because file-based encryption is still unsupported on these custom ROMs.
You could install LineageOS instead, but I haven't yet updated that for T510XXS2ASK1. I've just been busy and Andy hasn't been releasing any new LineageOS 16 GSIs. We're also pretty close to releasing a LineageOS 17 build.
Click to expand...
Click to collapse
fountainb234 said:
Hey guys, this is my first post. I just bought a Samsung SM-T510 and would like to unlock all the features. I'm currently trying to follow multiple guides on how to do so. To my understanding, my best bet is lineageOs 16. I've been following https://forum.xda-developers.com/gal...-16-0-t3987317 alongside with https://forum.xda-developers.com/gal...howto-t3989361 and I'm pretty confused on the method order i need to follow. What I mean is do I install rom first, TWRP, Magisk etc.?
More guides ive been following:
https://forum.xda-developers.com/gal...-10-1-t3934805
https://forum.xda-developers.com/app...mless-t3473445
https://topjohnwu.github.io/Magisk/i...system-as-root
I see posts saying I need and don't need Multidisabler so I'm confused on what I actually need: https://forum.xda-developers.com/gal...ption-t3963020
Another one: https://forum.xda-developers.com/gal...ption-t3919714
https://forum.xda-developers.com/gal...eries-t3918699
I have so many tabs open currently; I know I'm missing a few important ones.
So given all that info, i think i have all the software to do this between kernels, rom, twrp, odin, magisk, multi disabler? and i think thats all.
My sm-t510 build number is T510XXU2ASK5, looking through the lineage rom guide, I click the link https://samfrew.com/model/SM-T510/ and i see different versions. I'm honestly completely confused about this file and how I'm going to use it. I understand it to be the stock rom? as in factory software? With TWRP too, the numbers don't match my current build number leaving me very confused.
Do I need to downgrade my build number (i don't know if it's even a thing just asking)?
I think i can do everything relatively easy once I have an understanding of what to do first (order of things) and the specific files for the specific steps. When I'm reading these guides, I honestly have no idea which download goes for what. For ex. going back to https://forum.xda-developers.com/gal...-16-0-t3987317 like what do I need to download, the build number listed in notes regarding kernel or go to the download section right below and use that? Or both and if both, how do I use them separately for there a specific purpose? I cannot find anything that makes me feel comfortable rooting/custom rom on my device. Not comfortable in terms of I don't know what I'm doing exactly. I have put days of reading into this and still, I cannot figure out how to do this. I would really appreciate it if someone could help me. This is stressing me out and I would like to get this done before Monday due to me having some serious surgery. The reason being; I won't be as fresh on everything I've read recently.
I'm sorry if this post is choppy and all over the place. I'm just exhausted and clueless at this point. If I left any info out in order for someone to help me please let me know so I can provide it.
EDIT: The TWRP file ends in build number SK1, the file lineage-16.0-20191019-UNOFFICIAL-T510XXU2ASI4.tar.md5 doesn't match the TWRP file as well as my current build number; which ends in SK5. So nothing is matching the 3 last characters in my build number across all guides besides the samfrew link.
Also, I keep seeing i need a .tar TWRP file for recovery (?) but when I unzip both files are .img (named boot/recovery)
Click to expand...
Click to collapse
without reading answers i can say that im with YOU! Im almost 3 days to root my T510! We must RAMDISK YES in Magisk but to do that we need to extract recovery.img (https://www.droidwin.com/install-magisk-in-recovery-root-android/) from stock original ROM T510OXM5CUJ1 and Im stucked at the part NORAMDISK trying to patch recovery.img with Magisk Manager (with recovery mode checked) but i only get the "waiting for device in ADB" and I conect disconect USB C and nothing...Still NO RAMDISK...
I used 3 different ROMS but no lucky and tried with firmware CUJ1 but no lucky again. Without "NORAMDISK: YES" no root...stucked. But i saw a T510 with OrangeFOX!
framC0 said:
without reading answers i can say that im with YOU! Im almost 3 days to root my T510! We must RAMDISK YES in Magisk but to do that we need to extract recovery.img (https://www.droidwin.com/install-magisk-in-recovery-root-android/) from stock original ROM T510OXM5CUJ1 and Im stucked at the part NORAMDISK trying to patch recovery.img with Magisk Manager (with recovery mode checked) but i only get the "waiting for device in ADB" and I conect disconect USB C and nothing...Still NO RAMDISK...
I used 3 different ROMS but no lucky and tried with firmware CUJ1 but no lucky again. Without "NORAMDISK: YES" no root...stucked. But i saw a T510 with OrangeFOX!
Click to expand...
Click to collapse
I just finished flashing the latest Nexus ROM and rooted it with Magisk merely by flashing the Magisk zip file. You can flash the Nexus ROM without first flashing anything else but the latest CUL1 (not CUJ1) stock ROM. Nexus includes both TWRP and gapps. The only time you have to patch things to get Magisk installed is when you are trying to root a stock ROM instead of a custom ROM. Custom ROMs always to the patching for you.
lewmur said:
I just finished flashing the latest Nexus ROM and rooted it with Magisk merely by flashing the Magisk zip file. You can flash the Nexus ROM without first flashing anything else but the latest CUL1 (not CUJ1) stock ROM. Nexus includes both TWRP and gapps. The only time you have to patch things to get Magisk installed is when you are trying to root a stock ROM instead of a custom ROM. Custom ROMs always to the patching for you.
Click to expand...
Click to collapse
Wow i will try this today and will post feedback. Are you on Android 11? Thank You!
UPDATE: So...flashed with T510XXU5CUL1...
From OEM stock firmware:
Unlock bootloader -> done
Hold Vol Up & Vol Down buttons during restart to enter Download mode
Install TWRP to AP with Odin --> twrp-3.6.0_11-2-T510XXU5CUL1-20220218.tar ---> this put the tablet into emergency mode... had to do again "Hold Vol Up & Vol Down buttons during restart to enter Download mode" and reflash it again. stucked at this point. cant flash TWRP with that! Maybe this TWRP file its for Android 11.2 and im on 11?
framC0 said:
Wow i will try this today and will post feedback. Are you on Android 11? Thank You!
UPDATE: So...flashed with T510XXU5CUL1...
From OEM stock firmware:
Unlock bootloader -> done
Hold Vol Up & Vol Down buttons during restart to enter Download mode
Install TWRP to AP with Odin --> twrp-3.6.0_11-2-T510XXU5CUL1-20220218.tar ---> this put the tablet into emergency mode... had to do again "Hold Vol Up & Vol Down buttons during restart to enter Download mode" and reflash it again. stucked at this point. cant flash TWRP with that! Maybe this TWRP file its for Android 11.2 and im on 11?
Click to expand...
Click to collapse
You don't need to flash TWRP if you flash https://forum.xda-developers.com/t/...k-for-2019-galaxy-tab-a-10-1-sm-t510.4234889/ TWRP is built into this ROM. After installing stock CUL1, did you boot it, connect to wifi, skip the rest of setup and then enable Dev mode before rebooting to download and flashing from Odin?
edit: Don't attempt to download from the regular download link. Use the link under Build archives that says Android File Host and scroll down till you find the CUL1 md5 file.
lewmur said:
You don't need to flash TWRP if you flash https://forum.xda-developers.com/t/...k-for-2019-galaxy-tab-a-10-1-sm-t510.4234889/ TWRP is built into this ROM. After installing stock CUL1, did you boot it, connect to wifi, skip the rest of setup and then enable Dev mode before rebooting to download and flashing from Odin?
edit: Don't attempt to download from the regular download link. Use the link under Build archives that says Android File Host and scroll down till you find the CUL1 md5 file.
Click to expand...
Click to collapse
AH! So donwloaded Nexus_Stock_CR_T510XXU5CUL1-20220219.tar and put into AP in Odin... and FAIL. Error: "Only official released binaries are allowed". Before i flashed with T510XXU5CUL1 didnt conect wifi and enabled usb debug.
EDIT: i dont have OEM unlock option in DEV but its unlocked, i checked when in downloaded mode it says "lock device and..." so its unlocked.
framC0 said:
AH! So donwloaded Nexus_Stock_CR_T510XXU5CUL1-20220219.tar and put into AP in Odin... and FAIL. Error: "Only official released binaries are allowed". Before i flashed with T510XXU5CUL1 didnt conect wifi and enabled usb debug.
Click to expand...
Click to collapse
You must connect wifi and enable Dev mode before flashing. If, after flashing CUL1, you went through the regular setup routine and put in a Google Account, you must also enable OEM in Dev options.
lewmur said:
You must connect wifi and enable Dev mode before flashing. If, after flashing CUL1, you went through the regular setup routine and put in a Google Account, you must also enable OEM in Dev options.
Click to expand...
Click to collapse
YES!!!!!! YOU ARE THE BEST!!!! Done! It booted directly to TWRP!!! THANK YOU!!!! So now will flash Magisk with twrp right? Alawys rooted my devices but this 510 wow...never saw a thing like this
Edit: The fight continues - So i did wipe and format data in TWRP and reboot system and im IN. Installed Magisk 23.0.apk and noticed that im still with "RAMDISK: no"... Searching how to do next to root! Im very near of the goal!!!! Finally! Big thanks to lewmur!
lewmur said:
I just finished flashing the latest Nexus ROM and rooted it with Magisk merely by flashing the Magisk zip file. You can flash the Nexus ROM without first flashing anything else but the latest CUL1 (not CUJ1) stock ROM. Nexus includes both TWRP and gapps. The only time you have to patch things to get Magisk installed is when you are trying to root a stock ROM instead of a custom ROM. Custom ROMs always to the patching for you.
Click to expand...
Click to collapse
I just finished flashing the latest Nexus ROM and rooted it with Magisk merely by flashing the Magisk zip file.
Click to expand...
Click to collapse
Sorry just one more question im very near. I will flash this Magisk (magisk_patched-24300_tkk90.img) in TWRP or Odin? And is this file from https://forum.xda-developers.com/t/...019-galaxy-tab-a-10-1-sm-t510.4234889/page-18 ?
My brain will explode few days in a row to get it rooted
EDIT: Since an older version dont know witch, Magisk Manager and Magisk are joined in apk so i just flashed Magisk 23.0.apk in TWRP...rooted!!! DONE!!!! FINALLY
framC0 said:
Sorry just one more question im very near. I will flash this Magisk (magisk_patched-24300_tkk90.img) in TWRP or Odin? And is this file from https://forum.xda-developers.com/t/...019-galaxy-tab-a-10-1-sm-t510.4234889/page-18 ?
My brain will explode few days in a row to get it rooted
Click to expand...
Click to collapse
Download latest Magisk from https://magiskapp.com/zip/ and flash with TWRP.
lewmur said:
Download latest Magisk from https://magiskapp.com/zip/ and flash with TWRP.
Click to expand...
Click to collapse
Thank you!! Im facing a problem when connect USB to PC...sometime tablet restarts and sometimes dont appear on PC even in device manager. Did you got this also? Not very important because i will access via FTP. Just to learn...thanks!
framC0 said:
Thank you!! Im facing a problem when connect USB to PC...sometime tablet restarts and sometimes dont appear on PC even in device manager. Did you got this also? Not very important because i will access via FTP. Just to learn...thanks!
Click to expand...
Click to collapse
USB cables are notorious for being flaky. Sometimes it helps to just turn the cable over and plug it back in. I always keep several on hand so that if I have connection problems I can try another cable.