Hi
I have a Qtek 9000 and recently I broked the display. As I had the service manual I thought I coud replace the display by myself. I bought a new LCD + touch screen on ebay and the replacing of the LCD was easy and went quite well. The lcd works fine but the touch screen don't. I cheked and clean all the contacts but couldn't make the touch screen work.
So I wrote de seller and we agree to send back de display and receive a new one that he will test bofore posting.
I placed this new display and the problem remais the same. The lcd works fine but the touch screen don't, so I think the problem could not be here.
I made a hard reset and even downgraded to the original ROM but the touch screen still not working.
Can anyone help me with this
Thanks
Have you tried the touchscreen side of things before re-asembling the casing?
I have had problems with the seal on the casing around the screen activating the touch screen permanently - so that it runs really slow (if at all) when using the keypad.
damn, did you get the touch screen to work at all?
which LCD + touch did you buy from ebay? hopefully we can avoid this seller and get something that works.
ever thought of buying the touch screen separately and putting that on?
Let us know how it goes.
whitemoo.
after disasembling/asembling device had the same ussie with touch,after a cup of hours using it.
armandoramos try to open,when UNI works,only a part of UNI with LCD(look page 21 in service manual-bottom picture,page 22 & page 23-middle picture),then try how works your touch.If it works-you just had pinch the LCD coaxial cable module.
i had a problem with my touch screen, i was lucky enough to find a second hand uni in a local market with a busted lcd but working TS.
i swopped over the TS and re-assembled my uni, one thing i did have to add was a tiny piece of foam between the ribbon cable assembly and the case, this was to push the two ribbon cable sections (TS and LCD) together, for a better connection, relying on the sticky bits alone was not enough.
hope this helps.
Hi there I have problem with my vario II one it was working fine next day i woke up took my phone off the charging and guess what? touch screen stop responding and its been a month my phone working fine except touch screen I opened the phone up thought it might be loose connection and i read on the forum some where that it might a rust on the edges of chip or something but thats not the case. And I am double minded now do change the screen or ribbon cable? i Have seen screen on ebay for 40GBP and ribbon cable for about 55GBP. any help would be apreciated thanks in advance
same issue,follow here:
http://forum.xda-developers.com/showthread.php?t=285062
Hello, I have a Motorola Defy, that I dropped a few times, so the LCD screen got damaged with blue dots on it, I made a mistake and thought that the problem was on the touch Screen, so I purchased a replacement, installed but, it was damaged, the touch did not respond correctly, I wasn't able to type correctly among other problems.
I got a refund, then ordered a LCD screen replacement, now that I have it here, I install it, and it's broken:crying: I know, bad luck and being a rookie while trying to fix my phone, ok, I put back my old (damaged) LCD screen to use it in the meantime, and the old touch screen, but now, the old touch screen that was supposed to being working fine, it doesn't, it has the same problem as the touch screen that I bought.
Question is: the problem with the touch screen, could be related to the damaged LCD screen? or the motherboard of the phone is damaged? the phone works great, the apps, the games, everything but the touch screen and the LCD screen, but, as I said, I went back to the default touch screen after using the damaged one that I received, and it works worse I don't know what's wrong, please help me out, sorry for the long post
Please post questions in the Q&A section. Moved there.
Put it in the freezer for 1-2 hours
Sent from my MB525 using xda app-developers app
ppero196 said:
Put it in the freezer for 1-2 hours
Sent from my MB525 using xda app-developers app
Click to expand...
Click to collapse
Is this true?
true. fix some minor dead pixel if you put in freezer for one day. but your case... im dont hope much.
Try changing LCD + Capacitive Digitizer. (after trying the freezer trick ofcourse)
Well i will tell my story, which is related to your's as well,
i had a phone with resistive touch screen and it got screwed up, that is it does not respond correctly. So, i took it to the service center and they replaced the digitizer (touch screen) saying that previous one is broken. But, luckily the new one didn't responded to any touches they make.So, they replaced it again with the old one quoting that "your phone can't be repaired". So, i took it home with me.
Later i thought to calibrate the screen but the old one is not responding any more, no matter where i press
Later i calibrate it with the help of a software for windows mobile with the help of a PC. It took me to the calibration screen, from where i calibrated it, and voila, it worked... as good as a new one :victory:
long story short,
i think when you disconnected your digitizer, phones default values/drivers got messed up and are unable to find the new or the old digitizer you connect. I suggest you to go to the service center as these screens can not be calibrated.
Is there NO WAY at all to recalibrate the screen from the phone itself? or using an application? the delicalibration might be the problem....I'd like to fix it myself :/ thanks for the tip, never heard about it before!!
saman0suke1 said:
Is there NO WAY at all to recalibrate the screen from the phone itself? or using an application? the delicalibration might be the problem....I'd like to fix it myself :/ thanks for the tip, never heard about it before!!
Click to expand...
Click to collapse
Did you change the LCD and the Digitizer (both of em) again ?
dark_prince said:
Did you change the LCD and the Digitizer (both of em) again ?
Click to expand...
Click to collapse
I replaced my original digitizer screen for the one I ordered it, it gave me problems, so I went back to the original one, which was working fine, and now it's not fully responding, that's why I'm assuming is something calibration related, thanks!
help
my search button back light is not glowing ..i saw it is also not glowing in recovery...any help
Hello to all my guys HD2 after some months of inactivity, yesterday I turned back and I found the surprise ugliest in the world, the touch does not go, can you tell me what can I do? to make it work again?
EDIT: if I hold the touch screen floor of 1 inch from the shell of the phone the touch and that it works beautifully.
EDIT 2: I tried it with the tester, and if I measure the frequency of current flowing from the motherboard to the screen with DCV 200 and 0.29 so it's not a motherboard problem (or rather, it seems to me that it is not)
check digitizer connections & lcd ribbon to mainboard & if all look ok & reseating them makes no difference to digitizer function then expect new digitizer is needed.
Not expensive & also very very common for digitizer fault on HD2 ...
So I bought a HD2 with bad touch screen. The issue was the very common one that every one knows, red button that was poking into the touch screen flex cable. I opened up the phone and fixed the issue and touch screen was working perfectly fine. In the process, unfortunately, I chipped a little edge of the front glass/digitizer. It was not a big deal as phone was still working fine. But I decided to buy a new front glass.
When my new front glass arrived, I separated the digitizer/front glass from LCD, but then half of my LCD got corrupted. So I ended up buying an LCD too!!!
Now comes the issue: when I put the phone together, touch screen doesn't work at all. I have tried all combinations of NEW / OLD digitizer and NEW / OLD lcd. Nothing works. I wonder if anyone can help me figure out why?
P.S. When testing, I happened to connect the phone to my 5w wall charger directly connecting it to power pins (without battery installed). Would that be why I lost touch? Is the touch issue now because of motherboard that was directly connected to adapter, not getting power from its designated battery?
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
b3rvirus said:
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
Click to expand...
Click to collapse
Yes I had tried the old LCD, and that didn't work either.
I installed a WiFi Keyboard on it.
Did you resolve this issue?