Hi
When I adjust the screen light to half or lower it affect the time it takes to unlock the phone.
If I set it to about 20% it can take up to 3 sec. to unlock.
At 100% it unlocks immediately.
When set to auto adjust light according to surroundings the phone unlocks quickly below a lamp and extreme slowly in darkness.
During slow unlock the animation showing the icons in the dock area are shown in verical lines.
https://youtu.be/68l7sNC7uP4
Looks like a hardware issue to me. Probably it's a sign to upgrade..
Related
Hi,
i have a problem with my three days old HD. Besides the fact it seems to be much slower than it should be, the problem is the screen goes dim after a while. I'm not talking about it going black after a while, like it's supposed to, but in normal working mode it just kinda becomes darker, kinda like notebook screen goes a little dim when you unplug it from power. When i turn it on, it looks ok, but after a while, mostly after it first time goes black due to inactivity, the screen looks dimmed, no matter what i do, and after a few minutes it returns to normal, without any apparent reason, kinda random. At first i thought it might be something in HDTweak, so i did the factory reset, but it's happening again. Any ideas?
Try disabling the light sensor. It is supposed to adjust the screen brightness automatically, depending on the external light conditions. You can disable it in 'Energy', under Start -> Settings.
Well, it sort of works. When i disable the light sensor, i get the screen for adjusting the light on battery and AC. When i adjust the slider for battery, the screen lights up and it's ok. But, the moment the device locks itself (via HDTweak setting, the only thing i adjusted in HDTweak, it dims, and when i unlock it, it's still dimmed. Then when i again go into light sensor setting and press on the slider, it lights up. I don't understand what's going on. Faulty device maybe?
Also try changing the settings in the advanced tab.
Adding a minute or reducing a minute here seems to kickstart the device - and the annoying screen dimming goes away.
r
Andrew
just wondering what people think about this - im finding whenever I open my email the screen flashes bright for half a second and then dims down. anyone know why this is? is it design? a glitch? power surge? is the brightness limited to save power? (if so where is the diagnostic setting to change it ?)
it does it even on full brightness.
just seems a little weird is all!
That's because of the Amoled-screen.
When displaying a bright white background, the power consumption of the AMOLED-screen goes through the roof. Therefore, whenever a large white area is detected, the screen brightness is automatically decreased.
It's not just in the EMail-application but always when the background is white.
I am currently running JPA/JPB Hybrid firmware and I was wondering if there even is a sensor for the auto-brightness.
Normaly I have set my brightness to the lowest level, which is enough for indoor usage. But as soon as I am outdoors in the sunlight I can't even tell if the display is on or off with this brightness level.
Now the strange thing about this is that it does not seem to make a difference whether you check the "Power saving mode" in the Display settings or not - the Display brightness always stays the same:
- with the highest level it does not get darker in very dark rooms to save battery
- with the lowest level it does not get brighter even in direct sunlight, which makes the display unusable
On the left of the Samsung-logo there are 2 "holes", I guess one must be the proximity sensor and the other one the brightness sensor?
Is there any way to have the brightness on a very low level in dark rooms and on a high level in bright rooms / outdoor WITHOUT switching manually? Even switching with a widget sucks, because outdoors the display is so dark that I can't even draw the pattern to unlock the screen first (at least not without covering the display from the sunlight)
If there is I think the driver is missing so it's useless.
There is a brigness sensor, not for auto adjusting the screen brighness, for example try *#0*# and press sensor, now if you put you finger on the sensor, you phone vibrates, it means it is dark, if your finger is not on the sensor, it says, its brighten outside, that is for example to telephone, the screen goes dark, when you put the phone to your ears
"that is for example to telephone, the screen goes dark, when you put the phone to your ears"
No, that's the proximity sensor, and I think there is no light sensor in SG3, because that test app shows only proximity, accelerometer and magnetic sensor.
rueolps said:
Now the strange thing about this is that it does not seem to make a difference whether you check the "Power saving mode" in the Display settings or not - the Display brightness always stays the same:
- with the highest level it does not get darker in very dark rooms to save battery
- with the lowest level it does not get brighter even in direct sunlight, which makes the display unusable
Click to expand...
Click to collapse
Power Saving is not for dynamically change the strenght of backlight. It's just turning to lowest level when your battery is 15% and less.
And there is 2 holes, for proximity sensor. Try to cover one hole, and it doesn't work. Why? Because 1 hole sending an infrared (I think...) wave, and second is receiving that back, from eg., your hand.
JoHnNy08PL said:
Power Saving is not for dynamically change the strenght of backlight. It's just turning to lowest level when your battery is 15% and less.
And there is 2 holes, for proximity sensor. Try to cover one hole, and it doesn't work. Why? Because 1 hole sending an infrared (I think...) wave, and second is receiving that back, from eg., your hand.
Click to expand...
Click to collapse
totaly makes sense - thank you very much!
Hi everyone
I want to share a workaround to all of us who owns a defective S5
Symptom: You unlock your phone and it doesn't show anything. Actually, the phone is working. Capacitive buttons light up and you may heard some activity in the phone
Your phone has a defective screen. There are a lot S5 which have this problem, according to several forums. After several tries, unlock and lock over and over, the screen light up and you are able to use your phone. The problem is when you receive a call and you want to know who is calling you, the screen doesn't illuminate and you won’t be able to know who is.
Here's a workaround which makes your powerful S5 usable and take out from your drawer.
Solution:
The more effective way to fix it is: change defective screen! But sometimes it could cost as much as a new phone, or simply you can't afford it, and it's better to change your phone instead, and you put your S5 in a drawer.
The technical explanation of this problem is: Screen doesn't receive enough electrical current at low brightness levels (maybe the flex is defective, get old, etc)
Most probably the wake up problem exist together with screen flicker at low brightness levels
The wake up problem rises up more in dark environment, when light sensor make low bright screen
The lock screen light up screen, with a dim effect: when you lock the phone, it slowly turn screen off, and when you unlock, it make and effect of dim screen.
When you are is in dark environment, the effect is very slow, preventing the screen illuminate because the technical problem explained before.
When you are in very light environment, you lock screen and sensor light make the screen very brilliant and chances are you defective phone wakes up correctly.
We can use an app which give us complete control over brightness subsystem. I use an app called Velis AutoBrightness:
Once installed from Play Store, it shows a Setting Wizard. Follow the instructions. Below are some notes
• 1/7: Welcome Screen
• 2/7: How bright... Most probably is your phone always have flicker in low brightness. Choose "AMOLED" or "AMOLED bright". By the way choosing any one of those cure always minimum brightness failure!
• 3/7: Choose High sensitivity
• 4/7: On, if you want additional brightness when charging. Irrelevant for this thead. Choose your favorite setting
• 5/7: Same of 4/7
• 6/7: Choose enable: That enable the app
• 7/7: Some additional notes: Press Done
Now important settings: go to Menu > Settings > General: Settings Mode > Advanced
Service Activation settings:
• Disable system handler > ON: When you use Power saving mode, you surely noted screen flicker, which is very annoying, and make unusable power saving mode. By set this ON: Android doesn't set screen too dim; instead Velis have a minimum of brightness set by Wizard 2/7. (Surely you find out that you avoid screen flicker, by setting autobrightness off and slider in 8-10%)
Sensors settings:
• Screen-on sensor value override: Set this value to 30000. Read below this post if you want technical explanation of this setting
After you establish these settings, you'll be able to unlock your phone all the time!
This is the trick: When you unlock your phone, you'll note that the screen is very bright (because Screen-on to 30000) and quickly adjust to the environment light. The failure is that electrical current to screen is defective, and when exterior light is dark, the screen make a dim effect and doesn't light up.
Note to Marshmallow users:
• This app make use of Screen overlay permisions: And marshmallow is very restrict with this kind of app. This is specially true when you are installing an app. All you have to do is deactivate the app in notification screen: press "OFF" button, adjust system brightness upper enough to not flicker the screen, install your app, and activate Velis Autobrightness again
• Because of Doze mode, wake up from this mode may avoid your screen light up, the first time you use your phone. Let 10-15 seconds your phone wake up, lock again, and unlock again, and velis will make its work!
I hope this post make your smartphone usable. I barely apply this trick to two phones, but I think this is a good workaround!
I used this app & the flickering is still available
What worked for me is downgrading the firmware on my g900f all the way back to Android 4.0. My phone came with version 5.0 and I noticed the problem only after I kept installing samsung's system updates. Will report if the problem starts up again but I'm running rooted and running nougat just fine so I don't see a reason to keep upgrading the firmware.
Edit: nevermind, this didn't work
Reyse said:
The technical explanation of this problem is: Screen doesn't receive enough electrical current at low brightness levels (maybe the flex is defective, get old, etc)
Click to expand...
Click to collapse
Does anyone know for sure if it's the flex cable or some capacitors? I notice only the lower half of my screen flickers.. I bet there's a simple electrical fix for it instead of replacing the whoooole display
fbs said:
Does anyone know for sure if it's the flex cable or some capacitors? I notice only the lower half of my screen flickers.. I bet there's a simple electrical fix for it instead of replacing the whoooole display
Click to expand...
Click to collapse
Hello,
Have you change jour battery? If it s old it could cause some issues...
But try to buy a genuine one, I think that your battery must be old now.
Bye
cedouic said:
Hello,
Have you change jour battery? If it s old it could cause some issues...
But try to buy a genuine one, I think that your battery must be old now.
Bye
Click to expand...
Click to collapse
it doesn't make any sense. the lower half of the screen flickers in green even on charger
fbs said:
it doesn't make any sense. the lower half of the screen flickers in green even on charger
Click to expand...
Click to collapse
I noticed that screen only flickers at low brightness when using Boeffla kernel for LOS14 and others based on it.
No issue for the same device with LOS or Stock based kernels.
zlazaar said:
I noticed that screen only flickers at low brightness when using Boeffla kernel for LOS14 and others based on it.
No issue for the same device with LOS or Stock based kernels.
Click to expand...
Click to collapse
you're wrong
I was using los16 with stock kernel for months with flicker everyday
fbs said:
you're wrong
I was using los16 with stock kernel for months with flicker everyday
Click to expand...
Click to collapse
+1 to that , i even went back to stock and the screen flicker appeared and such issues are well known already with samsung amoled panels back in 2014-even some panels from 2018 . So def not kernel related.
I was using los 15.1 and this problem got worse. The phone was barely usable as mentioned by the op. In my case, the screen would start flickering below 60%. Then I switched back to stock marshmallow. I noticed that 100% brightness in los 15.1 is actually only about 70% in the stock rom.
I have been using the phone at 80% brightness for some weeks now and the problem has significantly reduced. But not completely gone, it's much much better. Also, you might want to avoid using dark wallpapers.
i recently bought a used s7 edge. the cellphone's display is damaged buf overall it works fine. except for a few issues mainly related to light sensor according to my understanding.
1: the display flickers when auto brightness turned off or when brightness is set to anything less than maximum
workaround: i installed screen filter app to control the brightness
2: the screen goes to green screen of death when device is put to sleep
workaround : turn AOD to always on and never Turn it off
3: the display goes to green death screen during call and wont get normal unless call is ended and screen is locked and turned on..
4 : at AOD ,the screen flickers at night time or in a dark place but gets back normal in bright light..
info i need : i thought what if it was possible to change the android framework values for the light sensor so that no matter whatever the light of the surrounding may be.. the device will always think it's in bright light.
for example if the settings for current values are
high 5000 medium 2000 low 600
then i change it to
high 1000 medium 500 low 25
so that the device will always think its in full bright area..
can anyone help me in achieving this goal? thanks