I found a combination ROM for my G950F with bootloader2 and have loaded it and bypassed FRP using adb all good.
I then tried to flash the stock ROM G950FXXU2CRF7 with Odin but it doesn't do it. I've tried different Odin versions:
v3.09 & v3.10 results in:
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin.lz4
<ID:0/004> NAND Write Start!!
but gets stuck there forever.
v3.12 results in:
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> sboot.bin.lz4
<ID:0/004> param.bin.lz4
<ID:0/004> up_param.bin.lz4
<ID:0/004> cm.bin.lz4
<ID:0/004> boot.img.lz4
<ID:0/004> recovery.img.lz4
<ID:0/004> system.img.lz4
<ID:0/004> userdata.img.lz4
<ID:0/004> cache.img.lz4
<ID:0/004> Home Binary Download
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> modem.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response from boot-loader
<ID:0/004> modem_debug.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response from boot-loader
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/006> Added!!
but the factory binary is still on there
Seem to be stuck on factory binary ROM now - any help appreciated!?
Beasty.Phingers said:
I found a combination ROM for my G950F with bootloader2 and have loaded it and bypassed FRP using adb all good.
I then tried to flash the stock ROM G950FXXU2CRF7 with Odin but it doesn't do it. I've tried different Odin versions:
v3.09 & v3.10 results in:
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin.lz4
<ID:0/004> NAND Write Start!!
but gets stuck there forever.
v3.12 results in:
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> sboot.bin.lz4
<ID:0/004> param.bin.lz4
<ID:0/004> up_param.bin.lz4
<ID:0/004> cm.bin.lz4
<ID:0/004> boot.img.lz4
<ID:0/004> recovery.img.lz4
<ID:0/004> system.img.lz4
<ID:0/004> userdata.img.lz4
<ID:0/004> cache.img.lz4
<ID:0/004> Home Binary Download
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> modem.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response from boot-loader
<ID:0/004> modem_debug.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response from boot-loader
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/006> Added!!
but the factory binary is still on there
Seem to be stuck on factory binary ROM now - any help appreciated!?
Click to expand...
Click to collapse
Use latest version of Odin 3.13.1
It supports the new lz4 compression format
https://samsungodin.com/
spawnlives said:
Use latest version of Odin 3.13.1
It supports the new lz4 compression format
https://samsungodin.com/
Click to expand...
Click to collapse
awesome, thank you! :good::good:
Que agradable sujeto! @ spawnlives
I just logged in to say thank you good sir. I am gratefull.
Best Regards.
Link to download G950FXXU2CRF7 combination rom please
Hi I have been searching everywhere for G950FXXU2CRF7 combination rom without success can you please provide the download link.
Regards
Gullabot
I tried with the latest version of odin but it did not work out it gets stuck in Factory binary what can I do?
Adecho91 said:
I tried with the latest version of odin but it did not work out it gets stuck in Factory binary what can I do?
Click to expand...
Click to collapse
What errors are you getting?
What are your trying to flash?
Related
i'm having a weird glitch in odin and i can't figure it out.
My log is
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
What firmware version are you trying to flash and what firmware version is the device currently on?
Sent from my Nexus 9 using XDA Free mobile app
The fail auth indicates that you are flashing a firmware with the bootloader at a lower version than the one on the phone. The bootloader just CANNOT be downgraded.
as jmjoyas mentioned, you cannot downgrade your phone, with (it appears to be so) the exception of a few versions. Several updates make a hardware change to the device by blowing qfuses.
I'm trying to flash any of the recovery tings to install a coustom roms
But when I try flashing it in Download I get this
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
And then my phone restarts and boot into the os.. Odin is just sitting there and saying RESET and after a minute continues with:
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
What is wrong? I have a G900F with android V5.0
littleme02 said:
I'm trying to flash any of the recovery tings to install a coustom roms
But when I try flashing it in Download I get this
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
And then my phone restarts and boot into the os.. Odin is just sitting there and saying RESET and after a minute continues with:
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
What is wrong? I have a G900F with android V5.0
Click to expand...
Click to collapse
And now? Don't get the problem you got. Did you try to boot into recovery with the three button combo?
Hello
When i try to flash TWRP via Odin it stops with rqt_close.
I followed the Guide in the TWRP Thread.
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Can somebody help me?
Hi all,
Good day,
I trying to use Kingo Root to root my phone but halfway it failed. It stuck in Odin mode.
I tried to use Odin 3 to recover it back but it seems is not working.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any idea what causing it stuck in system.img?
Please help to save my phone, almost 24hr since it died.
What model ??
DragonMebius said:
Hi all,
Good day,
I trying to use Kingo Root to root my phone but halfway it failed. It stuck in Odin mode.
I tried to use Odin 3 to recover it back but it seems is not working.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any idea what causing it stuck in system.img?
Please help to save my phone, almost 24hr since it died.
Click to expand...
Click to collapse
Looks like you need pit file for revive you phone from death.
Hello guys
I have a problem flashing my phone with odin
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Complete(Write) operation failed.
this is the problem
tried reinstalling drivers and changing odin but it doesn't work, any help
What firmware are you trying to flash? Try your repair firmware (four .md5 and one .pit files). They should never fail.