So my nephew brings me his galaxy s6 t-mobile phone... He forgot his lock pin so he factory reset it. Now he can no longer get into the phone because he doesnt know the correct email or password. I did some digging through the net watched a few videos... and found none of the methods they used to bypass the lock would work on his phone. Then I read about the Combination Rom (Factory Binary)... At this time I do not have any windows pc's and my VM will not read the usbs of the phone... (im not that experienced with vm to set this up) So i grabbed JOdin for linux and proceeded to try to flash the binary. However, JOdin did not work for me. So i found Heimdall and installed to learn that i had to find some weird way to run it as SU for it to work... Tho Heimdall worked like a charm.... With Heimdall I had to take the rom and completely extract it to a folder and find all the img files in it to install on heimdal like sboot, boot, cm, system, and quite a few others as well.I used the "PIT" file from the combination rom (which came in the download). When done installing the phone boots into Factory Binary... Interesting little rom... From here you can access settings, tho the instructions tell you to enable developer options and turn on usb debugging... in this rom they are set on by default i believe, so that was kind of a waste of time... then from the main menu you click the icon that looks like a calculator and type in "*#0808# where you are then presented with usb options. Select the last one on the list with adb at the end of it, click save and reboot. At this point I thought i was supposed to install the stock rom back (that was where i was lost) however all you have to do is let it boot back to binary. After it has reloaded... plug it into the pc and send it the proper adb instructions to disable frp lock. Techeligible has a batch file for use in windows, however if you dont have windows like me that does no good... So I went into the batch file with a text reader and extracted the information i needed ( 3 adb commands).In terminal i made sure my adb and fastboot were updated and working. I learned that when you type "adb devices" it will show the phone and if it says nothing else you are good to go. However it may give you a problem with permissions. If this is the case then unplug and make sure usb debuggin is on, you can also check that the adb is enabled again by doing the *#0808# command again and make sure the last selection is checked. When all is in order... At first I thought all commands must work for it to succeed... However this is not true at all. Only one of the adb commands will not give an error and at that time you can reboot into download mode and install the stock rom back on. After installation the phone will reboot and FRP Lock is no longer on... Now you can go into settings open up developer settings (tap build number till it unlocks) and select "OEM Unlock" and turn it on. Make sure usb debugging is on and you can boot back into download mode and install TWRP without a hitch.
I tried installing a couple of custom roms, however I have had no success with getting one to boot. (always stuck in boot loop even with wipe or factory reset) so I gave up and left him with the stock rom. If anyone has any idea of how i could get passed the bootloop maybe i can try again for him sometime and see how he likes various custom roms, but now he is happy he has his phone back working and it only took me a week of off and on frustration to figure it out... Hope this helps someone... (please dont ask for links) but if you do need help or have questions feel free to ask.
I'll be making a video for this with the 7 inch tablet on Nov. 29th or 30th (depending on the time I have)
General Disclaimer: I'm not responsible if you brick your tablet. This is how I did it personally as other methods here didn't work for me. I have yet to test this method on a 7 inch, also do not have access to the Surf variants. This has only been tested on the 10.1 inch with the keyboard. Will update when I test with the 7 inch.
What's Needed:
MTK Fastboot Drivers: https://online.mediatek.com/Public Documents/MTK_Android_USB_Driver.zip
Magisk Manager Canary: https://forum.xda-developers.com/apps/magisk/dev-magisk-canary-channel-bleeding-edge-t3839337
Stock Boot Image: https://forum.xda-developers.com/wa...eral/stock-stock-backups-images-otas-t3998227
ADB and Fastboot: https://www.xda-developers.com/what-is-adb/
Prerequisites:
Personally, I had issues getting my PC to recognize the tablets in Fastboot mode. The drivers wouldn't install. This might be optional for some of you, but I thought I'd include it just in case.
Installing MTK Fastboot Drivers from the link above
If you plugin your device in fastboot mode and your PC doesn't recognize it, follow these steps. If it did, skip this part.
1.) Download the drivers above and unzip the Zip file somewhere on your PC (desktop or My Documents is easiest)
2.) Boot your Tablet into Fastboot Mode by holding Vol + and Power, then select Fastboot from the Menu
*NOTE* There is a bug with these tablet's that the volume buttons are mislabeled. Really dumb, but I guess that's why they were 55 bucks for the 10 inch on black friday
3.) Plug the device into your PC and open Device Manager by pressing WinKey+R and typing devmgmt.msc, hit Enter
4.) If there's an Other Device listed called Android, follow these steps. If it isn't there, follow the next set of steps
5.) Open a Command Prompt window as Admin and type the following command
Code:
bcdedit.exe /set nointegritychecks on
6.) Hit enter, then restart your PC
7.) Once the PC is restarted, make sure your tablet is connected in Fastboot mode and open Device Manager again
8.) Right click Android under Other Devices and select Update Drivers
9.) Click the Browse my Computer for driver software button and select the MTK Folder you extracted from the download link above
10.) From there, you can open command prompt, type fastboot devices and see if your tablet shows up and move on to root!
Unlocking your Bootloader
From here, you can unlock your bootloader very easily to Root your device
This will wipe all data off the tablet!
0.) Enable OEM Unlock and USB Debugging on the tablet by going to Settings->About and tap Build Number 7 times. From here, enter the new Developer Options that unlock and turn on OEM Unlock and USB Debugging.
1.) Boot your tablet into Fastboot mode and connect it to your PC
2.) Open a Command Prompt window and type the following command, then hit enter
Code:
fastboot flashing unlock
3.) Follow the instructions on screen to unlock your bootloader
4.) Now Boot your device and we'll move on to making a rooted Boot Image
Creating a Rooted Boot Image with Magisk Manager
0.) Make sure you already have Wifi setup and connected before the first time you open Magisk Manager on your device! Make sure it auto connects as well
1.) Download Magisk Manager Canary from the link above
2.) Install it to your device
3.) Download boot Image from the Stock Boot Image part of the Prerequisites above and put the boot.img on your devices internal memory
4.) Open Magisk Manager and select Install Magisk
5.) Select Patch File and select the boot.img from your internal storage
6.) Once its done patching the image, take magisk_patched.img from the downloads folder of your device and move it onto your PC
7.) Boot your tablet into Fastboot mode and plug it into your PC
8.) Open Command Prompt and type the following command and hit enter (make sure you know your magisk_patched.img file location)
Code:
fastboot flash boot magisk_patched.img
9.) Reboot the device and you'll be Rooted!
Optional Steps like Modules and Debloating
My basic debloat script: https://forum.xda-developers.com/wa...s-general/root-walmart-bloat-remover-t4011639
Will be testing GSI roms on the spare 7 inch and will list those here
Recommended Magisk Modules:
Viper4Android Legacy
FDE.AI
MagiskHide Props Config
Systemless Hosts
Youtube Vanced Black
Magisk Setting to Enable:
Magisk Hide
Rename Magisk Manager App (keeps app from detecting magisk root)
Credits:
Myself for this root method @byproxy for reminding me to add the steps for OEM Unlock and enabling wifi before opening Magisk Manager for the first time
I'll start this off saying i'm an amateur at this, but I cannot for the life of me get an option to show up in magisk to patch the boot image even though it's on my 7" tablet. Any thoughts?
The bootloader was unlocked and it was successful so that's not the issue.
Are you online? I had the same problem.
Xavster2 said:
I'll start this off saying i'm an amateur at this, but I cannot for the life of me get an option to show up in magisk to patch the boot image even though it's on my 7" tablet. Any thoughts?
The bootloader was unlocked and it was successful so that's not the issue.
Click to expand...
Click to collapse
Xavster2 said:
I'll start this off saying i'm an amateur at this, but I cannot for the life of me get an option to show up in magisk to patch the boot image even though it's on my 7" tablet. Any thoughts?
The bootloader was unlocked and it was successful so that's not the issue.
Click to expand...
Click to collapse
Sorry, been a busy few days, but make sure you're connected to Wifi, close Magisk Manager, then reopen it and you'll be good to go!
Onn 8" walmart tablet
I purchased the 8" Onn walmart tablet second hand from a store called dirt cheap. Box didnt look to be opened but it had been. The tablet had been setup with someones gmail account that i do not know. The tablet was for a 4yo girl to use to learn preschool. Is there just any simple way to remove this google FRP lock ? I dont care if i lose the info on it as its not mine. I just want her to be able to use the tablet. Any help would be much appreciated please
CoachDad said:
I purchased the 8" Onn walmart tablet second hand from a store called dirt cheap. Box didnt look to be opened but it had been. The tablet had been setup with someones gmail account that i do not know. The tablet was for a 4yo girl to use to learn preschool. Is there just any simple way to remove this google FRP lock ? I dont care if i lose the info on it as its not mine. I just want her to be able to use the tablet. Any help would be much appreciated please
Click to expand...
Click to collapse
Forced factory reset should do it. There is small pin hole near the power button. I believe pressing this hidden button(with a Sim card ejector, or paper clip).
If pressing does not do anything. Maybe press the button then hold power button too
mrmazak said:
Forced factory reset should do it. There is small pin hole near the power button. I believe pressing this hidden button(with a Sim card ejector, or paper clip).
If pressing does not do anything. Maybe press the button then hold power button too
Click to expand...
Click to collapse
Thank you for responding so fast. I've boot into recovery mode /wiped everything...its back to factory. The pinhole reset button does nothing other than reboot it . Ive tried all combos to with the reset button but nothing. Also i've read that its possible to use odin? if i can get it into download mode.
Ive downloaded the stock rom posted on an sdcard wondering if i can possibly update in recovery mode? Im sorta a newb at this stuff. I've been reading for 4 days on this matter. I've practiced a root on an old tablet with success. I guess at this point unless i can sell it as is giving the customer that it has this frp lock on it. If the know how to fix it so be it. Im not sure there is a working solution for frp bypass on these tablets.
CoachDad said:
Thank you for responding so fast. I've boot into recovery mode /wiped everything...its back to factory. The pinhole reset button does nothing other than reboot it . Ive tried all combos to with the reset button but nothing. Also i've read that its possible to use odin? if i can get it into download mode.
Ive downloaded the stock rom posted on an sdcard wondering if i can possibly update in recovery mode? Im sorta a newb at this stuff. I've been reading for 4 days on this matter. I've practiced a root on an old tablet with success. I guess at this point unless i can sell it as is giving the customer that it has this frp lock on it. If the know how to fix it so be it. Im not sure there is a working solution for frp bypass on these tablets.
Click to expand...
Click to collapse
This is an mtk device not Samsung. So there is no Odin or download mode. There is spflash tool, and preloader.
And if you flash firmware (with default frp partition) then frp lock is cleared.
But you will have to find that file. It maybe in the stock firmwares that are shared, I do not know.
EDIT:
i was having issues but figure it out. maybe it should be so common knowledge that it shouldn't need to be included as a step, but since i don't do this THAT often i didn't think about it and it took me a bit to figure out why i was having issues.
once you get your computer to recognize your device (mine did without needing to mess with any drivers) you need to first make sure to got into the tablet settings -> about and then tap on the build number 7 times to access developer options. then you need to go into developer options and turn on OEM Unlocking & USB Debugging.
THEN follow the guide to unlock bootloader.
then (since the tablet is factory reset once you unlock) do the above AGAIN to turn USB Debugging back on after you reboot.
also note that you need to have an internet connection on the tablet to utilize magisk. once you got all that square, then continue on with steps for full root.
hope that helps!
byproxy said:
EDIT:
i was having issues but figure it out. maybe it should be so common knowledge that it shouldn't need to be included as a step, but since i don't do this THAT often i didn't think about it and it took me a bit to figure out why i was having issues.
once you get your computer to recognize your device (mine did without needing to mess with any drivers) you need to first make sure to got into the tablet settings -> about and then tap on the build number 7 times to access developer options. then you need to go into developer options and turn on OEM Unlocking & USB Debugging.
THEN follow the guide to unlock bootloader.
then (since the tablet is factory reset once you unlock) do the above AGAIN to turn USB Debugging back on after you reboot.
also note that you need to have an internet connection on the tablet to utilize magisk. once you got all that square, then continue on with steps for full root.
hope that helps!
Click to expand...
Click to collapse
I did not realize I didn't include that step. Total noob mistake when typing a tutorial up for android. I do this almost daily at work, so I forget to include it
CoachDad said:
Thank you for responding so fast. I've boot into recovery mode /wiped everything...its back to factory. The pinhole reset button does nothing other than reboot it . Ive tried all combos to with the reset button but nothing. Also i've read that its possible to use odin? if i can get it into download mode.
Ive downloaded the stock rom posted on an sdcard wondering if i can possibly update in recovery mode? Im sorta a newb at this stuff. I've been reading for 4 days on this matter. I've practiced a root on an old tablet with success. I guess at this point unless i can sell it as is giving the customer that it has this frp lock on it. If the know how to fix it so be it. Im not sure there is a working solution for frp bypass on these tablets.
Click to expand...
Click to collapse
I was able to remove FRP lock on one of mine by flashing the stock rom with SP Flash Tool. I used the full wipe and download selection with every partition selected including boot.
no worries! i didn't think about it either until i was having issues. thanks for the tutorial... it was super helpful!! btw it definitely works on the 8" tablet.
Hello! I'm new to all of this, but what I'm trying to accomplish is removing the Google account from this tablet and putting a new image on the ONA19TB002, ONA19TB003, ONA19TB007, Surf 7 and 10 tablets. I followed all of the steps as far as installing the drivers. I had to go through hoops to get the MediaTek Drivers installed, but I have a "warning" cone by it. I haven't been able to find any resolution to this. Any help would be appreciated. I' have a Windows 10 64-bit system that I'm using and the tablet I'm specifically working on at the moment is the ONN ONA19TB003 tablet. The tablet is not being recognized by my laptop when I run the 'fastboot devices' command in PowerShell. Is there something that I'm missing? Any help would be appreciated.
'Quis said:
Hello! I'm new to all of this, but what I'm trying to accomplish is removing the Google account from this tablet and putting a new image on the ONA19TB002, ONA19TB003, ONA19TB007, Surf 7 and 10 tablets. I followed all of the steps as far as installing the drivers. I had to go through hoops to get the MediaTek Drivers installed, but I have a "warning" cone by it. I haven't been able to find any resolution to this. Any help would be appreciated. I' have a Windows 10 64-bit system that I'm using and the tablet I'm specifically working on at the moment is the ONN ONA19TB003 tablet. The tablet is not being recognized by my laptop when I run the 'fastboot devices' command in PowerShell. Is there something that I'm missing? Any help would be appreciated.
Click to expand...
Click to collapse
Personally, I avoid PowerShell at all costs. This kinda stuff has always just seemed to work better with CMD.exe instead of Powershell.
These tablets are kind of a nightmare for this. If you've done the mediatek drivers and still have the warning cone icon, I'm not sure what's next as I haven't hit that wall myself. All I can maybe recommend is right click delete drivers in Device Manager, then start over with the driver install
Removing the Google Account would be needing a FRP Bypass. Someone above stated "I was able to remove FRP lock on one of mine by flashing the stock rom with SP Flash Tool. I used the full wipe and download selection with every partition selected including boot. " so if you can get it recognized, try that
KaptinBoxxi said:
Personally, I avoid PowerShell at all costs. This kinda stuff has always just seemed to work better with CMD.exe instead of Powershell.
These tablets are kind of a nightmare for this. If you've done the mediatek drivers and still have the warning cone icon, I'm not sure what's next as I haven't hit that wall myself. All I can maybe recommend is right click delete drivers in Device Manager, then start over with the driver install
Removing the Google Account would be needing a FRP Bypass. Someone above stated "I was able to remove FRP lock on one of mine by flashing the stock rom with SP Flash Tool. I used the full wipe and download selection with every partition selected including boot. " so if you can get it recognized, try that
Click to expand...
Click to collapse
Ok, thank you! This is a shot in the dark, but in order for ADB to work, USB debugging has to be enabled. I can't do that as the tablet is locked by FRP and I have looked countless times on Google and MSN to see if it's possible. Do you have any tips for that?
I don't know what I'm doing wrong, but for some reason I can't seem to get. The tablet to stay in fastboot mode. It just says waiting for device.
will this root onn 8 inch tablet running android 9
soateufel said:
I don't know what I'm doing wrong, but for some reason I can't seem to get. The tablet to stay in fastboot mode. It just says waiting for device.
Click to expand...
Click to collapse
Sorry for late reply. Been away from home with work. When fastboot mode indicates "waiting for device," it generally means that your device is not properly communicating with your PC or laptop. This is nearly always due to missing or incorrect drivers 9n your computer. There are several comprehensive guides here on XDA for installing necessary ADB & Fastboot drivers.
installed magisk manager on onn 8 and also have img zip but win i go to patch it magisk manager crashes
when you mean patch boot img do mean to unzip file on onn 8
Hi Guys,
Today I think I bricked my phone and I would appreciate any help.
I will describe the whole situation.
So around 2019 May, I rooted my device and decided to flash a stock based,debloated custom rom. Everything work just fined including downloading mode and recovery menu. Today, I decided to try out [S7/S7 Edge][OneUI Pie][JetBlackUI] LightROM, however strangely I was not able to boot either to TWRP neither to downloading mode via key combination.
However I had install TWRP app and from there i was able to boot to recovery mode,install the new rom and try it out.
For some reason root was not enabled in the new rom, so i figured I will try to do it via TWRP however I was unable to boot, since root access is needed to boot from TWRP app + key combo still did not work.
After searching on google, I found a poprgram which can do the trick. (Recovey-Download (CMD)
With this I was able to boot to recovery mode. Now I thought, since all this mess up was started with the new roms, I decided to restore my original stock rom, which I had a back up of. It booted up first and seemed okay, but I was curious if this solved the issues with the key comb, so I tried it going downloading mode, but it only worked with the program ((Recovey-Download (CMD)), and I saw that it is probably not gonna be good, since it only had the blue screen, but no data in the upper left corner.
Then I restarted the device and now it say " Custom binary blocked by FRP lock". and turns off itself.
I saw that FRP lock could be solved easly with Odin fresh install, problem is I have no idea how to go downloading mode. ( Assuming at this point I still can).
Sorry for the long essay but i think the more detail the easier to diagnose. Also, thank you for reading.
I would greatly appreciate any help.
BR
Csaba
Managed to solve it with USB JIG.
Is your phone an Exynos/Snapdragon variant?
csesztes said:
Managed to solve it with USB JIG.
Click to expand...
Click to collapse
Hey, how did you manage to get your phone into dl mode with an USB jig? I want to try this out, but you're the only one here who's confirmed that you were able to do this on an S7 Edge.
edit:
problem solved, got the h918 up and running all right with download mode flashed back on, recent twrp on recovery,
20H and root.
this was just impossible for people with little knowledge like me. what helped in the end was a huge bunch of luck and reading reading reading. for hours and days. will now create complete guide for REAL helpless people (like me) that want just a rooted phone with twrp. thx to all the genius people that made so much possible here.
==================================================================================================
hi,
hope someone can help me with this since im struggling for weeks now.
got a H918, managed to unlock bootloader with linuxbootstick on laptop since it wont run on pc,
and got twrp on it with runningnaked whateveritis.
then i completewiped it, and... i cant remember ! somehow i got android working, but i couldnt restart into downloadmode. bcuz downloadmode is now twrp. i cant remember to have installed twrp as downloadmode.
also i dont have a keyboard anymore in android. first i wondered why playstore wanted to force me to speak to it, couldnt explain, then i noticed there is no keyboard present (i didnt delete it) ok fk it, complete wipe, restored backup of a fully functional OS (10p it should be i think) no keyboard present again AHA. i mean, i didnt make a bu without a keyboard present. so now i dont know whats going on. had a very hard time to have the phone being recognized by pc for running LGUP and downgrading from 20H to 10P, not possible now anymore. tried cables, ports, different picturetransferprotocol/mtp/midi etc. fastbootmode/twrp (downloadmode, in which it worked before is not accessible anymore)
i just cant make the phone being recognized by pc or laptop anymore. only way to get to twrp, is disconnect
usb-cable, turn phone off, hold volUP put in usb cable, yea, thats the way to get into downloadmode, now it starts into twrp. when holding volDOWN and plug in usb cable it starts into fastboot mode.
dont know what to do now.
when rebooting from twrp into twrp i get the NO COMMAND screen with dead android robot. i had a hard time with my v10, now with a little more experience, i just dont know what to do anymore. nothing will work, android deletes the keyboard FOR NO REASON and saves this into the twrp backup afterwards, yea ridiculous, i know.
what is this shlt? what can i do? i want a phone running rooted with magisk, lucky patcher and poweramp, thats not too much of request. someone got any ideas?
thx