I install TWRP recover in order to install superSU in forum.There was no problem until i install superSU.Firstly my display color mode is amoled cinema but it looked like basic,also i can't open my wifi,on notification panel on torch ,camera using by another application.Then i tried to reboot phone,after then up left corner it says custom binary blocked by PRM lock with red and not booting.Even i try to flash my phone again with stock rom it says "SW REV. CHECK FAIL DEVICE:2,BINARY:1".plz help me
BTW
the article that i downloaded files:
Related
Today I was trying to revert back to stock firmware and flashed the files in this thread:
https://forum.xda-developers.com/att-galaxy-s7/how-to/firmware-stock-sm-g930a-ph1-odin-files-t3458890
The flash failed, on the phone it game an eMMC error that says:
SW REV CHECK FAIL : [about]Fused 4 > Binary 2
[1] eMMC write fail: ABOUT
No other flashes were working after that even other stock images I tried. I held down the power button and I am now stuck with a blue android "erasing" screen that pops up every few seconds followed by some commands that go by too fast to see.
Is my phone dead? is there anything I can do?
EDIT: Wasn't going into boot loader properly and was able to flash new firmware
i'm install custom rom alexega_project_N950FXXU3BRA2 but can not power on show custom binary blocked. i'm download stock rom from sammobile but can not fash. show system rev. check fail device 1 binary 0. but can fash recovery official. but in recovery dm-verity error help me plzzzzz
It means it thinks you are downgrading, flash a newer stock rom
I installed TWRP so i could use Magisk and pass safetynet so i could use GooglePay. However during the process i mustve messed up. Currently i can enter TWRP aswell as Download mode however Odin gives the the error "Complete(Write) operation failed." and my phone says "SW REV CHECK FAIL DEVICE 3, BINARY 1"
My device is Galaxy S8 G950F UK H3G, i have checked that i am flashing the right firmware. In addition to this, when i try to boot normally im stuck on the "Samsung Galaxy S8" Boot screen.
Anyhelp would be much appreciated, i just want to get my phone working again.
Any reassurance with drivers and links to specific drivers would be useful, i installed all the ones i could find
Seems like your firmware you are trying to flash is older than the bootloader... try to flash the latest firmware and reply.
shayeque said:
I installed TWRP so i could use Magisk and pass safetynet so i could use GooglePay. However during the process i mustve messed up. Currently i can enter TWRP aswell as Download mode however Odin gives the the error "Complete(Write) operation failed." and my phone says "SW REV CHECK FAIL DEVICE 3, BINARY 1"
My device is Galaxy S8 G950F UK H3G, i have checked that i am flashing the right firmware. In addition to this, when i try to boot normally im stuck on the "Samsung Galaxy S8" Boot screen.
Anyhelp would be much appreciated, i just want to get my phone working again.
Any reassurance with drivers and links to specific drivers would be useful, i installed all the ones i could find
Click to expand...
Click to collapse
Yes thats what this error means your bootloader is updated and you are flashing older firmware than the device currently has by the device 3 I would assume your device is updated to revision 3 of firmware
Hi
i have SM-G935FD and i always like to try new Roms but this time i made mistake i forget " oem unlock " ...
i go to recovery and do full wipe(delete even Rom) and when i try to install new Rom it failed and switched off i try to install another software but same problem after some attempts phone show this message : KERNEL REV. CHECK FAIL. DEVICE:1, BINARY:0 and i can't access to recovery ....
i try to install original software with 4 file and flash by "Odin" but phone show this message: Custom Binary Blocked by FRP Lock ..!!
sorry but my English not that good ..:crying:
trying to disable FRP lock, I install COMBINATION_FA70_G950USQU6 on Galaxy S8 G950USQS5.
As you see different binary.
Is there any option to erase or change the COMBINATION ROM that is already installed (V6) for the correct one(V5) ?
I'm trying to install stock firmware G950USQS5 but ODIN FAIL! and downloading mode on S8 show a message in RED saying :
SE REV CHECK FAIL :[abl]Fused 6 >Binary 5
thanks in advance for those how try to help !
pacegra said:
trying to disable FRP lock, I install COMBINATION_FA70_G950USQU6 on Galaxy S8 G950USQS5.
As you see different binary.
Is there any option to erase or change the COMBINATION ROM that is already installed (V6) for the correct one(V5) ?
I'm trying to install stock firmware G950USQS5 but ODIN FAIL! and downloading mode on S8 show a message in RED saying :
SE REV CHECK FAIL :[abl]Fused 6 >Binary 5
thanks in advance for those how try to help !
Click to expand...
Click to collapse
No once you update your there. must flash 6 or above