hello ,
I had installed rescurssion remix rom on my phone and i had decided to change to stock rom. So I give my mobile to a mobile shop and they repaired and changed to stock rom.!!!!actually the problem is......after the repair of my mobile in the mobile shop when I switch power on it directly go to boot loader instead of showing boot logo..After that when it shows the update I updated . It suddenly HARD BRICKED.Only the white light near fingerprint sensor worked while charging. please help meee...:crying::crying::crying::crying:
please help me to make my mobile in good condition ........by solving the boot loader issue which shows as the start up...
If I've read your post correctly, you used an OTA update and that's when you had the white light blinking? When you connect your device to your computer, what is your device recognised as? Is it recognised as Qualcomm HS-USB 9008 or similar?
If so, you may wish to look at this guide to try to get your device fixed: https://forum.xda-developers.com/moto-g4-plus/how-to/moto-g4-plus-hardbrick-solved-guide-t3657761
Do you know what the shop did for the repair, what stock ROM did they flash to your device?
echo92 said:
If I've read your post correctly, you used an OTA update and that's when you had the white light blinking? When you connect your device to your computer, what is your device recognised as? Is it recognised as Qualcomm HS-USB 9008 or similar?
If so, you may wish to look at this guide to try to get your device fixed: https://forum.xda-developers.com/moto-g4-plus/how-to/moto-g4-plus-hardbrick-solved-guide-t3657761
Do you know what the shop did for the repair, what stock ROM did they flash to your device?
Click to expand...
Click to collapse
yes it recognize as Qualcomm HS-USB 9008 something like that
the shop has installed rom with build number NPJS25.93-14-18.....I think its april 2018 update
charuvilapauljohn said:
yes it recognize as Qualcomm HS-USB 9008 something like that
the shop has installed rom with build number NPJS25.93-14-18.....I think its april 2018 update
Click to expand...
Click to collapse
actually i did not know what did hey doo
what to do for the start up problem ith always starts with the boot loader
charuvilapauljohn said:
actually i did not know what did hey doo
what to do for the start up problem ith always starts with the boot loader
Click to expand...
Click to collapse
I'm confused by what help you're asking for, as you appear to be asking for help on how to fix a hard bricked device, and yet also asking for help on your device starting with the bootloader. If your device is fully hard bricked, then you wouldn't have a bootloader to boot to... Can I thus ask please is your device still in a blinking light state or are you now booting to the bootloader?
I asked you also in your other post if using fastboot oem fb_mode_clear would work in clearing the bootloader start: https://forum.xda-developers.com/showpost.php?p=76927663&postcount=421 However, if your device is truly hard bricked (and is in the Qualcomm HS-USB 9008 mode), then you need to try the blankflash as linked above, then re-flash the stock ROM - the NPJS25.93-14-18 April 2018 fastboot ROM and guide is here: https://forum.xda-developers.com/moto-g4-plus/how-to/stock-rom-npjs25-93-14-4-march-1-t3608138
thanks..it worked
It worked...thanks a lot...I installed NPJS25.93-14-18 rom....
Now there is another problem..both the sim and the finger print is not working
charuvilapauljohn said:
It worked...thanks a lot...I installed NPJS25.93-14-18 rom....
Now there is another problem..both the sim and the finger print is not working
Click to expand...
Click to collapse
That's because you phone model is changed to G4 only (not plus,) and lost 2nd IMEI... (Check in about section)
If it's changed to G4, follow,
Follow linked thread to solve: post #139, and better to read all posts to get correct information. (Turn pages to Download correct HW.img that's meant for your device model)
https://forum.xda-developers.com/mo...luss-model-changed-to-g4-lost-t3496912/page14
the hw.img file not working
____Mdd said:
That's because you phone model is changed to G4 only (not plus,) and lost 2nd IMEI... (Check in about section)
If it's changed to G4, follow,
Follow linked thread to solve: post #139, and better to read all posts to get correct information. (Turn pages to Download correct HW.img that's meant for your device model)
https://forum.xda-developers.com/mo...luss-model-changed-to-g4-lost-t3496912/page14
Click to expand...
Click to collapse
As I found a hw.img file for my xt1643.and i tried to install.The TWRP RECOVERY got struck.And the adb command prompt is not showing anything
Related
Hi, i dont know what happened before this state but now it is not booting and anything show on the screen. Device Manager shows Qualcomm HS-USB QDLoader 9008. Can this phone work normally or it is fully dead? Thanks in any case.
Optimusik said:
Hi, i dont know what happened before this state but now it is not booting and anything show on the screen. Device Manager shows Qualcomm HS-USB QDLoader 9008. Can this phone work normally or it is fully dead? Thanks in any case.
Click to expand...
Click to collapse
You can always get it up and running as long as it's only the software issue. Have you tried using the Wugfresh Toolkit/ any other toolkit and connecting your phone? Have you tried to reboot to bootloader or recovery?
If you haven't already, press and hold volume up + power button until you see the bootloader then connect your phone to your PC and install the toolkit of your preference and install the stock Rom, follow onscreen instructions on your PC. Hope this helps.
superviked said:
You can always get it up and running as long as it's only the software issue. Have you tried using the Wugfresh Toolkit/ any other toolkit and connecting your phone? Have you tried to reboot to bootloader or recovery?
If you haven't already, press and hold volume up + power button until you see the bootloader then connect your phone to your PC and install the toolkit of your preference and install the stock Rom, follow onscreen instructions on your PC. Hope this helps.
Click to expand...
Click to collapse
I would try this with pleasure but its always black screen anytime. And phone recognized by computer only in that mode that i described
It is definitely hard bricked. QDloader mode = Hard Brick. But if Google has released the blankflash files for the N6P (Idk if they have or not), then you can recover.
Optimusik said:
I would try this with pleasure but its always black screen anytime. And phone recognized by computer only in that mode that i described
Click to expand...
Click to collapse
This is the closest I found related to your issue, however this is the guide to resolve the same issue but for the Nexus 5 Hammerhead. Someone needs to confirm if the N6P images can be flashed with the same method.
http://forum.xda-developers.com/goo...-unbrick-nexus-5-stucked-qualcomm-hs-t3043301
superviked said:
You can always get it up and running as long as it's only the software issue.
Click to expand...
Click to collapse
Not true.
superviked said:
This is the closest I found related to your issue, however this is the guide to resolve the same issue but for the Nexus 5 Hammerhead. Someone needs to confirm if the N6P images can be flashed with the same method.
http://forum.xda-developers.com/goo...-unbrick-nexus-5-stucked-qualcomm-hs-t3043301
Click to expand...
Click to collapse
The boarddiag tool is specific to LG devices. It will be of no use here.
This is the first post I've seen for Angler that has a Qualcomm HS-USB QDLoader 9008. If it starts to happen more people will start to look into a fix. Until then I'm afraid the OP is bricked.
I'm having similar issues. For some reason I can't get passed the white Google screen. I can see the phone when I plug it in, wugfresh toolkit can even flash it back to stock. Yet, it won't go past the Google,in white, loading screen.
Sent from my SM-T800 using XDA-Developers mobile app
Have you installed TWRP, have you been able to boot into recovery/bootloader via ADB?
---------- Post added at 12:02 PM ---------- Previous post was at 11:40 AM ----------
theesotericone said:
Not true.
The boarddiag tool is specific to LG devices. It will be of no use here.
This is the first post I've seen for Angler that has a Qualcomm HS-USB QDLoader 9008. If it starts to happen more people will start to look into a fix. Until then I'm afraid the OP is bricked.
Click to expand...
Click to collapse
What I meant was the phone is not completely dead. It's in a state of coma but not dead. There's a way, it could take time but this can always come back to life, but the OP will have to wait for device and storage specific files and the boarddiag/ tool to reflash image files manually.
superviked said:
Have you installed TWRP, have you been able to boot into recovery/bootloader via ADB?
---------- Post added at 12:02 PM ---------- Previous post was at 11:40 AM ----------
What I meant was the phone is not completely dead. It's in a state of coma but not dead. There's a way, it could take time but this can always come back to life, but the OP will have to wait for device and storage specific files and the boarddiag/ tool to reflash image files manually.
Click to expand...
Click to collapse
I dont know the history of this phone. It came to me in this state. Now i know that i have to wait blankflash from Google. Thanks everybody for the answers.
Qualcomm HS-USB QDLoader 9008. Having the same issue. Hope there's a fix soon. Heart broken.
robertputt said:
Qualcomm HS-USB QDLoader 9008. Having the same issue. Hope there's a fix soon. Heart broken.
Click to expand...
Click to collapse
I would like to know what did you do to cause the phone to brick? I got the phone a week ago and I'm thinking if I should root or not. I became scared after I bricked my Moto X 2014 and there's still no blankflash files for it :crying:
seco2004 said:
I would like to know what did you do to cause the phone to brick? I got the phone a week ago and I'm thinking if I should root or not. I became scared after I bricked my Moto X 2014 and there's still no blankflash files for it :crying:
Click to expand...
Click to collapse
I did it myself, was trying to patchrom miui for the phone and must have used a wrong boot file or bootloader file, corrupted emmc.
first time i've ever hard bricked a phone and been flashing stuff for years, once you follow guides and use tested files you should be fine. found someone here in ireland to repair it for me. Only one huawei repair centre here
Recently found myself in the same predicament.
mzahiri said:
I'm having similar issues. For some reason I can't get passed the white Google screen. I can see the phone when I plug it in, wugfresh toolkit can even flash it back to stock. Yet, it won't go past the Google,in white, loading screen.
Sent from my SM-T800 using XDA-Developers mobile app
Click to expand...
Click to collapse
Same thing with my girlfriends phone, have u manage to fix it ? Thanx
letmarebrmbarove said:
Same thing with my girlfriend phone, have manage to fix it ? Thanx
Click to expand...
Click to collapse
http://forum.xda-developers.com/nexus-6p/help/figure-brick-t3450921
Check in here. No solution (yet, hopefully), but you're not alone with this issue.
count me in!
First of all, i live in Bangladesh. I asked a relative of mine who lives in Sweden to buy me this phone. So, there is no way for me to send this phone back to ZTE.
Now let me explain how i got into this huge mess. I installed twrp successfully using this post - https://forum.xda-developers.com/axon-7/how-to/guide-install-twrp-unlock-bl-flash-t3517379
i only followed part A of this post. Then i needed to root. so i tried to flash supersu 2.79 first but failed. Then i tried to flash supersu 2.65 as someone commented that they failed with 2.79 but succeeded with 2.65. However, after flashing supersu 2.65 i soft bricked my phone. i could still access twrp 3.0.2. After a while, i downloaded b08 update.zip and tried to flash it through twrp but failed. then i saw this post - https://forum.xda-developers.com/axon-7/how-to/guide-root-xposed-safetynet-stock-rom-t3530906
and this post - https://forum.xda-developers.com/axon-7/development/recovery-official-twrp-zte-axon-7-t3515715
And tried to update twrp to 3.03. which then hard bricked my phone. now i cannot access anything. when i try to start my phone it shows the zte logo for a second and the whole screen goes blank with the red led.
same thing happens with volume up+power and volume down+power. And there is no way to turn the phone off. So, i waited a whole day for the phone to empty it's battery and tried to boot to edl mode using volume up+down but Qualcomm HS-USB QDLoader does not appear. The only thing i can get to connecting to my computer is handset diagnostic interface.
Now only a brilliant dev can help me. So can someone PLEASE Help me.
Also i've found this post is very similar to my problem https://forum.xda-developers.com/axon-7/help/bricked-a2017g-b03-help-please-t3487635
Update: Fixed using this post >> https://forum.xda-developers.com/ax...ory-brick-repair-manual-t3585898#post71764940
& this >> http://4pda.ru/forum/index.php?showtopic=814221&st=0#entry60102671
Why can't you boot into EDL mode?
That's strange to me...
Did you try another computer to see if it pops up there?
Then try to reflash recovery if you can...
Abiram26 said:
Why can't you boot into EDL mode?
That's strange to me...
Did you try another computer to see if it pops up there?
Then try to reflash recovery if you can...
Click to expand...
Click to collapse
yes i have. but in the device manager, instead of Qualcomm HS-USB QDLoader, Handset Diagnostic Interface appears.
Furthermore, computers does not recognize any adb device when i connect my axon 7
what do i do???
Edit: when i uninstall Handset Diagnostic Interface from device manager and then connect my phone with both volume keys pressed, at first qusb_bulk appears but after automatic installation of hardware software it's Handset Diagnostic Interface all over again
Well I did some Google'ing for you and I guess the things in these threads might be your best bet:
http://www.modaco.com/forums/topic/343587-guide-de-bricking-a-zte-blade/ (same thread-ish on XDA: https://forum.xda-developers.com/showthread.php?t=2163493 )
http://www.modaco.com/forums/topic/337757-update-save-ur-bricked-v880-and-also-the-imei/
However all these methods are not tested with the Axon 7 and seem pretty risky to me...
If I were you I'd send the phone back to Sweden so the relative can send it back to ZTE.
I'm not sure if this falls under the ZTE warranty stuff so they might charge you a bit; anyhow it's still the better option than throwing this phone away I'd say.
I don't think I can really help you here, sorry :s
PS: If you are going to try these risky methods; don't blame me if it goes wrong...
EDIT: You might also want to try to go to the ZTE website and try to get some support from there (customer support, support from the forum/community ther, etc.)
Perhaps they can give you the right tools to unbrick your Axon7
Abiram26 said:
Well I did some Google'ing for you and I guess the things in these threads might be your best bet:
http://www.modaco.com/forums/topic/343587-guide-de-bricking-a-zte-blade/ (same thread-ish on XDA: https://forum.xda-developers.com/showthread.php?t=2163493 )
http://www.modaco.com/forums/topic/337757-update-save-ur-bricked-v880-and-also-the-imei/
However all these methods are not tested with the Axon 7 and seem pretty risky to me...
If I were you I'd send the phone back to Sweden so the relative can send it back to ZTE.
I'm not sure if this falls under the ZTE warranty stuff so they might charge you a bit; anyhow it's still the better option than throwing this phone away I'd say.
I don't think I can really help you here, sorry :s
PS: If you are going to try these risky methods; don't blame me if it goes wrong...
EDIT: You might also want to try to go to the ZTE website and try to get some support from there (customer support, support from the forum/community ther, etc.)
Perhaps they can give you the right tools to unbrick your Axon7
Click to expand...
Click to collapse
:crying::crying::crying::crying:
if only i could boot into edl mode
I don't think your phone is in such a dire condition. I was contacted by @raystef66 only last night. He made the same mistake as you did, trying to flash SuperSU via TWRP on a locked bootloader phone. However, he didn't take all steps you took.
If I were you, I'd try to somehow prevent the PC from automatically installing the ZTE DFU (Diagnostics) driver. You say the device appears to be in EDL mode when you connect it (QUSB_BULK) and then it installs new drivers. Can you somehow cancel that process?
Here's a microsoft guide on how to prevent your PC from automatically installing drivers. Maybe try that and reconnect your device. It might get recognised as QUSB_BULK and then you can restore your stock recovery via the Axon7tool? If you can do that, it shouldn't be a lost cause?
Send me a PM with your Hangouts, let's see if I can help.
Controllerboy said:
I don't think your phone is in such a dire condition. I was contacted by @raystef66 only last night. He made the same mistake as you did, trying to flash SuperSU via TWRP on a locked bootloader phone. However, he didn't take all steps you took.
If I were you, I'd try to somehow prevent the PC from automatically installing the ZTE DFU (Diagnostics) driver. You say the device appears to be in EDL mode when you connect it (QUSB_BULK) and then it installs new drivers. Can you somehow cancel that process?
Here's a microsoft guide on how to prevent your PC from automatically installing drivers. Maybe try that and reconnect your device. It might get recognised as QUSB_BULK and then you can restore your stock recovery via the Axon7tool? If you can do that, it shouldn't be a lost cause?
Click to expand...
Click to collapse
I have tried this, but axon7tool does not recognize any adb device. When i input adb devices command in cmd there is no device. However, it did get recognized as QUSB_BULK after disabling automatic driver installation through group policy. What do i do??
Edit: after seeing this post - https://forum.xda-developers.com/axon-7/help/2017g-dfu-mode-investigation-t3511191
i'm really panicking. "Handset Diagnostic Interface" is DFU mode. "handset diagnostic interface (DFU) (ComX)" i just ignored the DFU part when posting. Does this mean i cannot unbrick my phone???
Please Help
nsabir said:
I have tried this, but axon7tool does not recognize any adb device. When i input adb devices command in cmd there is no device. However, it did get recognized as QUSB_BULK after disabling automatic driver installation through group policy. What do i do??
Edit: after seeing this post - https://forum.xda-developers.com/axon-7/help/2017g-dfu-mode-investigation-t3511191
i'm really panicking. "Handset Diagnostic Interface" is DFU mode. "handset diagnostic interface (DFU) (ComX)" i just ignored the DFU part when posting. Does this mean i cannot unbrick my phone???
Please Help
Click to expand...
Click to collapse
You can make Windows to use the right driver so you will be able to use axon7tool. So if you have problems connecting to your phone as QUSB_BULK, download Zadig to your computer and replace your drivers with WinUSB ones. Open Zadig tool, go to Options and activate List all devices. Then select QUSB_BULK in the drop down control at the top and WinUSB in the lower control. Then click on the button to replace the driver. After this, QUSB_BULK should appear in the Device manager and you should be able to execute axon7tool and flash TWRP 3.0.2-2 signed again and continue with the unlock procedure.
If you have the QUSB_BULK with a warning icon then you need to install the Qualcomm usb driver.
All the answers on how to return to a working state or not falling into a soft brick like yours were just in the thread of the guide you didn't complete. Devices with the Qualcomm Snapdragon 820 are unbrickable. So do not panic, and read the whole thread [GUIDE] [A2017G] Install TWRP, Unlock BL, Flash Custom ROM.
Oki said:
You can make Windows to use the right driver so you will be able to use axon7tool. So if you have problems connecting to your phone as QUSB_BULK, download Zadig to your computer and replace your drivers with WinUSB ones. Open Zadig tool, go to Options and activate List all devices. Then select QUSB_BULK in the drop down control at the top and WinUSB in the lower control. Then click on the button to replace the driver. After this, QUSB_BULK should appear in the Device manager and you should be able to execute axon7tool and flash TWRP 3.0.2-2 signed again and continue with the unlock procedure.
If you have the QUSB_BULK with a warning icon then you need to install the Qualcomm usb driver.
All the answers on how to return to a working state or not falling into a soft brick like yours were just in the thread of the guide you didn't complete. Devices with the Qualcomm Snapdragon 820 are unbrickable. So do not panic, and read the whole thread [GUIDE] [A2017G] Install TWRP, Unlock BL, Flash Custom ROM.
Click to expand...
Click to collapse
My QUSB_BULK is not with a warning sign. And i have already used Zadig.
At first, i couldn't get past DFU mode. But after following @Controllerboy instructions i am able to get QUSB_BULK in my device manager. But it's all the same.
For axon7tool to work the computer has to first recognize my a2017g as a adb device. That's where the problem is. My phone is not being recognized as an adb device. When i use adb devices on cmd there is no listed device. I have already tried this with other computers but the results are the same.
what do i do??
Oki said:
You can make Windows to use the right driver so you will be able to use axon7tool. So if you have problems connecting to your phone as QUSB_BULK, download Zadig to your computer and replace your drivers with WinUSB ones. Open Zadig tool, go to Options and activate List all devices. Then select QUSB_BULK in the drop down control at the top and WinUSB in the lower control. Then click on the button to replace the driver. After this, QUSB_BULK should appear in the Device manager and you should be able to execute axon7tool and flash TWRP 3.0.2-2 signed again and continue with the unlock procedure.
If you have the QUSB_BULK with a warning icon then you need to install the Qualcomm usb driver.
All the answers on how to return to a working state or not falling into a soft brick like yours were just in the thread of the guide you didn't complete. Devices with the Qualcomm Snapdragon 820 are unbrickable. So do not panic, and read the whole thread [GUIDE] [A2017G] Install TWRP, Unlock BL, Flash Custom ROM.
Click to expand...
Click to collapse
My QUSB_BULK is not with a warning sign. And i have already used Zadig.
At first, i couldn't get past DFU mode. But after following @Controllerboy instructions i am able to get QUSB_BULK in my device manager. But it's all the same.
For axon7tool to work the computer has to first recognize my a2017g as a adb device. That's where the problem is. My phone is not being recognized as an adb device. When i use adb devices on cmd there is no listed device. I have already tried this with other computers but the results are the same.
what do i do??
nsabir said:
My QUSB_BULK is not with a warning sign. And i have already used Zadig.
At first, i couldn't get past DFU mode. But after following @Controllerboy instructions i am able to get QUSB_BULK in my device manager. But it's all the same.
For axon7tool to work the computer has to first recognize my a2017g as a adb device. That's where the problem is. My phone is not being recognized as an adb device. When i use adb devices on cmd there is no listed device. I have already tried this with other computers but the results are the same.
what do i do??
Click to expand...
Click to collapse
EDL mode has nothing to do with adb!!!!! adb only connects to recovery or a booted system. fastboot connects to bootloader, and Axon7tool communicates with the EDL bootstrap. In order to use Axon7tool (to flash or backup boot or recovery partitions) your computer has to detect your device as QUSB_BULK. Obviously in that mode adb or fastboot will not find your device in a compatible state.
What can you do?
1. read the whole thread, not just the opening post. As advised.
2. Use Axon7tool to flash the same TWRP 3.0.2-2 you flashed before. It is signed, so the bootloader detects it as a valid ZTE image even when the bootloader is still locked.
3. Unlock your A2017G phone.
4. enjoy flashing and reflashing all the multiple roms, patches, etc.
Oki said:
EDL mode has nothing to do with adb!!!!! adb only connects to recovery or a booted system. fastboot connects to bootloader, and Axon7tool communicates with the EDL bootstrap. In order to use Axon7tool (to flash or backup boot or recovery partitions) your computer has to detect your device as QUSB_BULK. Obviously in that mode adb or fastboot will not find your device in a compatible state.
What can you do?
1. read the whole thread, not just the opening post. As advised.
2. Use Axon7tool to flash the same TWRP 3.0.2-2 you flashed before. It is signed, so the bootloader detects it as a valid ZTE image even when the bootloader is still locked.
3. Unlock your A2017G phone.
4. enjoy flashing and reflashing all the multiple roms, patches, etc.
Click to expand...
Click to collapse
Sir, i don't u understand my problem properly. Let me give u a thorough description.
When i press and hold the power button the phone vibrates shows ZTE logo for less than a second then the screen turns off and the LED turns red.
When i press volume up+power same thing happens.
When i press volume down+power same thing.
And i cannot power off my phone no matter what i do it always stays at that state until the battery is empty.
Then if i press volume up+down at the same time and insert usb red led turn on.
And when i insert the usb in any of these states only one thing appears on my device manager is "Handset Diagnostic Interface (DFU) (ComX)"
But if i Uninstall Handset Diagnostic Interface (DFU) (ComX) from device manager and disable automatic driver installation through group policy then QUSB_BULK appears with a yellow sign.
If i use Zadig to install winusb driver then the yellow sign disappears.
U r telling me to read the whole thread. I have done so. But in DFU mode adb devices command doesn't list any device. If my computer doesn't see my device as an adb device how can i do anything.
I have also tried to use axon7tool -w recovery command since my device is in qusb_bulk mode. But cmd says no device detected.
2017 DFU mode investigation
Bricked A2017G
These posts have given me a big scare. Since no one has been able to recover from the same condition that i am in right now.
That's why i'm asking the help of experts. Please help me.
I have also came to a conclusion myself that if a tool like this Flashing recovery or this ZTE Open Download Mode or maybe this [TOOL][ALPHA] ZTE Warp 4G Unbrick Tool is not developed then this particular Qualcomm Phone is Brickable.
I am saying this because after a good amount of googling i came to know that when qualcomm phones are bricked it goes into emergency download mode which shows as "Qualcomm HS-USB QDLoader 9008" or "Qualcomm HS-USB QDLoader 9006" on device manager. And there are a lot of guides to unbrick from that state. But only old ZTE devices go into "Handset Diagnostic Interface (DFU) (ComX)" mode aka DFU mode.
And there are different guides for different models.
This is why i am panicking and asking for the help of experts. If there was a guide to recover from this state this post wouldn't exist. So if u can, please help.
And sorry for my english, i tried my best.
nsabir said:
Sir, i don't u understand my problem properly. Let me give u a thorough description.
When i press and hold the power button the phone vibrates shows ZTE logo for less than a second then the screen turns off and the LED turns red.
When i press volume up+power same thing happens.
When i press volume down+power same thing.
And i cannot power off my phone no matter what i do it always stays at that state until the battery is empty.
Then if i press volume up+down at the same time and insert usb red led turn on.
And when i insert the usb in any of these states only one thing appears on my device manager is "Handset Diagnostic Interface (DFU) (ComX)"
But if i Uninstall Handset Diagnostic Interface (DFU) (ComX) from device manager and disable automatic driver installation through group policy then QUSB_BULK appears with a yellow sign.
If i use Zadig to install winusb driver then the yellow sign disappears.
U r telling me to read the whole thread. I have done so. But in DFU mode adb devices command doesn't list any device. If my computer doesn't see my device as an adb device how can i do anything.
I have also tried to use axon7tool -w recovery command since my device is in qusb_bulk mode. But cmd says no device detected.
2017 DFU mode investigation
Bricked A2017G
These posts have given me a big scare. Since no one has been able to recover from the same condition that i am in right now.
That's why i'm asking the help of experts. Please help me.
I have also came to a conclusion myself that if a tool like this Flashing recovery or this ZTE Open Download Mode or maybe this [TOOL][ALPHA] ZTE Warp 4G Unbrick Tool is not developed then this particular Qualcomm Phone is Brickable.
I am saying this because after a good amount of googling i came to know that when qualcomm phones are bricked it goes into emergency download mode which shows as "Qualcomm HS-USB QDLoader 9008" or "Qualcomm HS-USB QDLoader 9006" on device manager. And there are a lot of guides to unbrick from that state. But only ZTE devices go into "Handset Diagnostic Interface (DFU) (ComX)" mode aka DFU mode.
And there are different guides for different models.
This is why i am panicking and asking for the help of experts. If there was a guide to recover from this state this post wouldn't exist. So if u can, please help.
And sorry for my english, i tried my best.
Click to expand...
Click to collapse
Can you boot into the bootloader by pressing the button combination?
Oki said:
Can you boot into the bootloader by pressing the button combination?
Click to expand...
Click to collapse
No i cannot. Everything seems to be pointing back to DFU mode.
I need something like Method 5 of this post How to recover a ZTE Blade/Libra/v880 after a bad flash for A2017G
nsabir said:
No i cannot. Everything seems to be pointing back to DFU mode.
I need something like Method 5 of this post How to recover a ZTE Blade/Libra/v880 after a bad flash for A2017G
Click to expand...
Click to collapse
Hi, maybe this can help you, is the chinese forum, i know is a shot in the dark, but your case i think need a special treatment, sorry for my english, the link:
http://www.myzte.cn/forum-1037-1.html
and the tutorials:
http://www.myzte.cn/forum.php?mod=forumdisplay&fid=1037&filter=typeid&typeid=2243
Use Google translator, and good luck, sorry if this is a waste of time for you, i am trying to help
PS: RMA chinese http://rma.zte.com.cn/
Altomugriento said:
Hi, maybe this can help you, is the chinese forum, i know is a shot in the dark, but your case i think need a special treatment, sorry for my english, the link:
http://www.myzte.cn/forum-1037-1.html
and the tutorials:
http://www.myzte.cn/forum.php?mod=forumdisplay&fid=1037&filter=typeid&typeid=2243
Use Google translator, and good luck, sorry if this is a waste of time for you, i am trying to help
PS: RMA chinese http://rma.zte.com.cn/
Click to expand...
Click to collapse
please don't embarrass me by saying sorry. I appreciate the fact that u even attempted to help me. thank u.
I am going through the Chinese posts and hoping to find something useful.
nsabir said:
please don't embarrass me by saying sorry. I appreciate the fact that u even attempted to help me. thank u.
I am going through the Chinese posts and hoping to find something useful.
Click to expand...
Click to collapse
Do you find something useful? I think I find someone in that forum, exactly in your position, all the answers pointing to RMA for the fix, sorry, maybe later can take another look and search for a solution.
Enviado desde mi ZTE A2017U mediante Tapatalk
nsabir said:
please don't embarrass me by saying sorry. I appreciate the fact that u even attempted to help me. thank u.
I am going through the Chinese posts and hoping to find something useful.
Click to expand...
Click to collapse
https://forum.xda-developers.com/showthread.php?t=3551590
Enviado desde mi ZTE A2017U mediante Tapatalk
Altomugriento said:
https://forum.xda-developers.com/showthread.php?t=3551590
Enviado desde mi ZTE A2017U mediante Tapatalk
Click to expand...
Click to collapse
Thank you for the link. But i tried this miflash tools weeks ago.
Here is the full guide in my opinion for the mi flash tool.
http://www.androidbrick.com/unbrick...-you-have-the-right-kind-of-rom-qhsusb_dload/
Unfortunately, the A2017G does not have 9008 port. It has ZTE's own Handset Diagnostic Interface (DFU) (ComX) for which i need the latest version of ZTE firmware flasher. At the moment only ZTE have this. So, my bricked phone is a lost cause.
Hullo,
I succesfully installed Lineage with no problems in the OS, but was unable to access TWRP as it asked for a decryption pattern that didn't seem to match the pattern I set on my phone. I then tried a password in the OS but this also didn't work in TWRP.
After checking the thread again, I found Unjustified had recommended the TWRP found in his bootloader, which I then downloaded and proceeded to install via fastboot. The installation appeared to go smoothly but after that I was unable to turn on my phone.
After pressing the power button I am presented with either the battery icon or the ZTE logo, which disspears after a few seconds followed by three flashing red lights. The last flashing light seems to be cut off part way.
I thought this might be a dead battery but even after charging for an extended period of time the result is the same.
Any help would be very much appreciated!
mvortex3710 said:
Hullo,
I succesfully installed Lineage with no problems in the OS, but was unable to access TWRP as it asked for a decryption pattern that didn't seem to match the pattern I set on my phone. I then tried a password in the OS but this also didn't work in TWRP.
After checking the thread again, I found Unjustified had recommended the TWRP found in his bootloader, which I then downloaded and proceeded to install via fastboot. The installation appeared to go smoothly but after that I was unable to turn on my phone.
After pressing the power button I am presented with either the battery icon or the Axon logo, which disspears after a few seconds followed by three flashing red lights. The last flashing light seems to be cut off part way.
I thought this might be a dead battery but even after charging for an extended period of time the result is the same.
Any help would be very much appreciated!
Click to expand...
Click to collapse
Your phone doesn't seem to be bricked at all.
That was a known issue many G users encountered...
Just boot into TWRP by pressing Power and volume + or choosing it from the bootloader warning screen and reflash the universal B15 N bootloader.
Reboot your phone and from now on it should boot every N rom just fine :fingers-crossed:
Good luck,
Martin
mischa_martin said:
Your phone doesn't seem to be bricked at all.
That was a known issue many G users encountered...
Just boot into TWRP by pressing Power and volume + or choosing it from the bootloader warning screen and reflash the universal B15 N bootloader.
Reboot your phone and from now on it should boot every N rom just fine :fingers-crossed:
Good luck,
Martin
Click to expand...
Click to collapse
I'm glad to hear it is quite common, but I should mention that the three lights persist when I try to load TWRP... I can only get as far as the ZTE logo.
The bootloader warning also hasn't shown since I attempted to flash TWRP as the phone appears to cut off after showing ZTE.
I will try an overnight charge in case the battery is completely empty and somehow slow charging. But any other suggestions are most welcome.
Kind regards,
James
mvortex3710 said:
I'm glad to hear it is quite common, but I should mention that the three lights persist when I try to load TWRP... I can only get as far as the ZTE logo.
The bootloader warning also hasn't shown since I attempted to flash TWRP as the phone appears to cut off after showing ZTE.
I will try an overnight charge in case the battery is completely empty and somehow slow charging. But any other suggestions are most welcome.
Kind regards,
James
Click to expand...
Click to collapse
You should try some button combinations like
Power + volume down
Power + volume down + volume up
And see how the device reacts
It helps connecting the device to a PC to look up in device manager to determine the mode its booted in
mischa_martin said:
You should try some button combinations like
Power + volume down
Power + volume down + volume up
And see how the device reacts
It helps connecting the device to a PC to look up in device manager to determine the mode its booted in
Click to expand...
Click to collapse
Thanks for the continued help.
I was just trying to connect it to the PC and appear to have made some headway, it started off showing up as qusb_bulk, but after repeatedly deleting that driver I returned to Qualcomm HS-USB QDLoader 9008 (COM6).
As I understand axon7root *should be able to write to the device at this point.
Does this device name give any indication as to the problem?
I wonder if miflash could be used on a G model to unbrick it. I'm happy to restart from stock files.
mvortex3710 said:
Thanks for the continued help.
I was just trying to connect it to the PC and appear to have made some headway, it started off showing up as qusb_bulk, but after repeatedly deleting that driver I returned to Qualcomm HS-USB QDLoader 9008 (COM6).
As I understand axon7root *should be able to write to the device at this point.
Does this device name give any indication as to the problem?
I wonder if miflash could be used on a G model to unbrick it. I'm happy to restart from stock files.
Click to expand...
Click to collapse
As you are in EDL now you have some options.
First I would try to flash a recovery and boot image that is proven to be working fine e.g official twrp https://forum.xda-developers.com/axon-7/development/recovery-official-twrp-zte-axon-7-t3515715 or some A2017G stock boot.img
If that doesn't help you could get in contact with @jcadduono to be a tester for that miflash method. (As your device is already pretty badly bricked)
I don't exactly know how EDL flashing works if it depends on a exact GPT table or not.
But I can say that I flashed every single part of the A2017U bootloader except for NON-HLOS (modem) on my A2017G for each B29 and B15 and it worked just fine. So maybe we just have to exchange the modem file in the EDL package :silly:
If you don't want to take that risk you also could try sending it back to ZTE and hope they don't check the bootloader :fingers-crossed:
(Just a thought: Maybe if the EDL package won't work on your device it will be so heavily damaged ZTE can't check for bootloader unlock and accept it as a warranty case, but don't take that too seriously )
Regards,
Martin
mvortex3710 said:
Thanks for the continued help.
I was just trying to connect it to the PC and appear to have made some headway, it started off showing up as qusb_bulk, but after repeatedly deleting that driver I returned to Qualcomm HS-USB QDLoader 9008 (COM6).
As I understand axon7root *should be able to write to the device at this point.
Does this device name give any indication as to the problem?
I wonder if miflash could be used on a G model to unbrick it. I'm happy to restart from stock files.
Click to expand...
Click to collapse
If you are not afraid then try to use my package for A2017G with MiFlash: https://mega.nz/#!88BjXKhA!TnVSobBw5PkmShSqZ-Ni8MCCbnhJP2SWRNvvXqYHSjc
I really appreciate all this advice!
Looks like the MiFlash is promising. I was able to load the phone into MiFlash from the [EDL] thread. I have just tried the A2017G package provided by djkuz and will report back with any updates.
Just got to the mifavor screen, charging the battery from empty, although quickcharge appears to be functional again.
The charging battery logo is different from before so appears that this bootstack has done the trick.
The flashing red light has gone now, appears to be loading Lineage as before! I'm so grateful for all this help
However, now the unlock pattern is coming up as 'wrong pattern'. Is there anything that can be done? My settings appear to be saved as before (wallpaper and quick settings are the same).
I will attempt to reinstall twrp recovery and fix the lockscreen over adb. Thanks very much for the help. The brick has gone!!
Hi,
During an android update (by OTA) my phone turnend off. Power button + volume down don't turn on the bootloader (nothing happens, I can only see a blackscreen).
Commands ADB and Fastboot don't work. Computer shows only a saying "Didnt recognized the USB device" or sometimes "Qualcomm HS-USB QDLoader 9008".
In the past the phone had TWRP and a lot of custom ROM's but I went back to stock.
Is it possible to flash it with PC? (With some kind of aplication like "smart phone flash tool")
Best regards!
You can't do anything. You lost your device. But if you find any solution then tell me.
bump
hubert987 said:
bump
Click to expand...
Click to collapse
You hard-bricked your device by Installing official OTA update in your unlocked device. This thing has happened to a lot of us unknowingly or by mistake. I did the same thing by mistake, I forgot about having an unlocked BL and flashed an official OTA update.
We basically fcuked up the bootloader/Fastboot I think and Motorola won't publish the required files to reflash it using Qfil.
i shut down my device by tapping power off. then removed sim card and sd card after screen went black. but when i tried to power on, it doesnt respond.. i tried holding the power button for 10s, it gives me a black screen and vibrates and instantly closes again.. so i cant boot into recovery, i cant boot to fastboot, and its unreadable on pc, it doesnt charge, no bootlogo, nothing. just bricked..
.
i dont know why, but it just bricked by itself.. i've been using mokee 9 date of 1/1/2020 thats the last update i installed, with add on su and everything was working perfectly and even if i reboot multiple times..
bootloader was unlocked so xiaomi centers wont help me..
how is it possible to make it boot again? i mean like wtf even happened? i did nothing.. i didnt flash anything and system was READ ONLY before powering off.. all i did was remove sim and sd cards... even after flashing mokee updates yesterday, it booted normally and idk what's going on..
any help?
EDIT: the phone's hard disk IC was damaged. I went to a tech guy and he changed it but then the motherboard broke entirely after flashing the qcn file for imei. Device out of warranty of course because of the damn bootloader. Thank you xiaomi for the great phone that only lasted one month before dying completely.
attempt 2
in attempt 1 i tried force reboot as mentioned, didnt work
attempt 2 : i tried force reboot while plugged to pc, this showed up
attempt 3
i tried to flash a new firmware, but device unreadable. must be on fastboot mode for mi flasher to be able to read it. im starting to lose hope.. the device is new though it makes me sad
on some topic of a bricked phone online, someone mentioned that he should try EDL mode, by cmd command FASTBOOT OEM EDL
so i tried it many times until it said successful. but still didnt fix anything, because it didnt actually boot into EDL mode, had to open my device physically and use test points. so attempt 4 failed
does this mean fastboot works?
after attempt 4, it said successful so if fastboot works like that then i can flash stock boot.img or something.. right? which image should i start with
forum
boody shaban said:
on some topic of a bricked phone online, someone mentioned that he should try EDL mode, by cmd command FASTBOOT OEM EDL
so i tried it many times until it said successful. but still didnt fix anything. so attempt 4 failed
Click to expand...
Click to collapse
this is the forum of the bricked phone similar to mine, except that i didnt try any flash like him it just happened randomly
https://c.mi.com/thread-2334646-1-0.html
attempt 5
attempt 5 failed, i tried flashing whole firmware one by one, i started with vbmeta, then recovery but it failed. idk what to do
notice
i have noticed that it only flashes small img files, if its 100kb or more it will fail. maybe due to device restart because the only way to make it read in fastboot mode is to force restart multiple times until it flashes. what to do now?
attempt 6
so according to this video
https://www.youtube.com/watch?v=yJoIiLE_w3w
he installed a driver (name in attachment) then refreshed on mi flash so his device became readable on mi flasher
i tried that but it didnt work.
final attempt.. out of hope
found the possible solution. its called a deep flash cable, i will just go to any tech guy and ask him for help.
see attachment for info.
boody shaban said:
found the possible solution. its called a deep flash cable, i will just go to any tech guy and ask him for help.
see attachment for info.
Click to expand...
Click to collapse
In order to enter test point / EDL / 9008 mode, you have to physically open your device and connect two points on the phone's board. Search on YouTube for Redmi 7a EDL. If you get to EDL mode, you can flash original stock firmware via MiFlash.
Reason for brick
cg730620 said:
In order to enter test point / EDL / 9008 mode, you have to physically open your device and connect two points on the phone's board. Search on YouTube for Redmi 7a EDL. If you get to EDL mode, you can flash original stock firmware via MiFlash.
Click to expand...
Click to collapse
Yes, I hate tearing up my device so I took it to a professional. He failed to open ADL but he did the 9008. Now he waits some kind of credit. Not sure if for the app to work or for the bootloader to unlock, although it was already unlocked but maybe somehow got locked..
Any way, expected reason for brick is either latest magisk module, or kernel tweaks..
I gave the device to a professional, but he also failed to flash it even with test point. He said he was searching for a file.. I dont remember its name, something like IMOH..
Now I need to know any possible reason that might brick my phone again to avoid it
cg730620
Click to expand...
Click to collapse
cg730620 said:
.
Click to expand...
Click to collapse
The app he used was called ultimate multi tools
test point attempt failed
i did the test point, booted to 9008 mode but still nothing.
i think i know why the phone got bricked by itself, it got ARB stands for AUTOROLLBACK
read more about it here https://mi-globe.com/unbrick-your-xiaomi-phone-without-authorized-mi-account/
bootloader got automatically locked again.
Never lock the bootloader if:
- your phone was delivered Chinese version and you flashed Global firmware
- your phone was delivered Global version and you flashed Chinese firmware
- you changed system, vendor, boot or recovery partition
- you installed a custom or modified stock rom
ARB isn't an issue with this phone I suppose. Because I was on 11.0.5 and rolled back to 10.2.5 without problems.
Have you tried MiFlash Pro?
See here:
https://forum.xda-developers.com/redmi-7a/how-to/miflash-pro-t4030809
---------- Post added at 04:01 AM ---------- Previous post was at 03:38 AM ----------
boody shaban said:
i did the test point, booted to 9008 mode but still nothing.
Click to expand...
Click to collapse
It seems that error is related to your computer. Reinstall drivers and MiFlash.
QDLoader Drivers:
http://www.mediafire.com/file/0jfq2r7adylnltu/QDLoader_HS-USB_Driver.zip/file
ADB driver:
http://www.mediafire.com/file/qskct06xyx1iivs/ADB%2Bdriver%2Bv1.17%2Blite.zip/file
MiFlash:
http://www.mediafire.com/file/bdjugf3zx7037yl/MiFlash2018-5-28-0.zip/file
Read about a similar problem here:
https://xiaomi.eu/community/threads/mi5-bricked-i-bricked-my-new-mi5-with-miui8.32439/
cg730620 said:
Never lock the bootloader if:
- your phone was delivered Chinese version and you flashed Global firmware
- your phone was delivered Global version and you flashed Chinese firmware
- you changed system, vendor, boot or recovery partition
- you installed a custom or modified stock rom
ARB isn't an issue with this phone I suppose. Because I was on 11.0.5 and rolled back to 10.2.5 without problems.
Have you tried MiFlash Pro?
See here:
https://forum.xda-developers.com/redmi-7a/how-to/miflash-pro-t4030809
---------- Post added at 04:01 AM ---------- Previous post was at 03:38 AM ----------
It seems that error is related to your computer. Reinstall drivers and MiFlash.
QDLoader Drivers:
http://www.mediafire.com/file/0jfq2r7adylnltu/QDLoader_HS-USB_Driver.zip/file
ADB driver:
http://www.mediafire.com/file/qskct06xyx1iivs/ADB%2Bdriver%2Bv1.17%2Blite.zip/file
MiFlash:
http://www.mediafire.com/file/bdjugf3zx7037yl/MiFlash2018-5-28-0.zip/file
Read about a similar problem here:
https://xiaomi.eu/community/threads/mi5-bricked-i-bricked-my-new-mi5-with-miui8.32439/
Click to expand...
Click to collapse
but im sure i have all drivers installed in fact i used mi flash more than once and it worked perfectly fine, and i swear i didnt try to lock it or anything, what happened is, mokee auto updates installed add on magisk and it was the latest version so i think this might have bricked it. idk..
ok i downloed all the drivers and reinstalled them, same error : "library not registered"