hi all i bought defy about a year ago as a second phone from ebay with cm7 installed.last week i purchase another phone and give my 7 years old daughter. however i reset everything and phone turn old version blur mod then stuck on m logo i download rom and sort the problem.
real problem starts now i try to install cm 9 download all required files wiped the phone and install the rom however it didn't restart stuck on black screen and only white led when connected with usb also didn't connect or recognized by rds lite.I found tread battery wake up from i think was ''mggrager'' or something else finally rds recognized the phone and install another sbf but still stays same as black screen and white.i read so many threats on this side or others and each i installed custom roms without clearing cache
battery replaced with replacement battery also original
all drivers installed
it doesn't respond any buttons or usb connection
rds only with battery jump
please help what to do
I'm having the same problem as you are, i believe... I had cm11 (or 10, not sure) installed for about a month now (back in december) .... Went on a trip, and when coming back my phone battery ran out at the airport... I take my phone home, not really giving it much importance, and i noticed it would never charge and/or turn on, and that when I connect it to the pc, nothing happened other than the white led coming on.. RSD won't recognized it...
So i found out i had to charge the battery manually, and used a Universal Charger... Still, no recognition by RSD Lite...
Finally, i found a way:
1. Open RSDLite
2. Connect phone (no battery on it)
3. While holding Power + Vol Up, put the battery in
4. RSD will recognize your phone!
Problem is, it recognizes my MB525 as "S Flash OMAP0360"
And when i try to flash a .sbf i used previously to recover my phone (had bricked it by trying to change ROMs in a sloppy manner), it seems to flash smoothly, but when it's going to reboot the phone, the progress goes up to 100% and then asks me to reboot it manually.. I read somewhere that to fix that i should take the battery out, disconnect the phone, put it back in, and make RSD recognize it like i mentioned before...... and after RSDLite says flashing is PASSED, the phone still won't turn on... I have tried at least three times and gotten the same result... Help?
I don't know if i should make a thread of my own.. i think we have the same problem, and i REALLY need my phone back.. so i guess we could just help each other fixing it somehow....
The SBF i am using (because it helped me save my phone before) is:
JORLA_U3_3.4.2_107-9_SIGNED_USAJORDMR1B25TIGCOLA01E.0R_JORLAFROTIGCOLA_P009_A002_M010_HWp3_WIG146037_Service1FF.sbf
EDIT: Also, i read somewhere that when all you get is the white led (when connecting to PC) it means that your battery is not charged enough for flashing.. ?
i already tried several times this method however no luck i am really not sure what to do any more i think only option try to find latest rom or first rom then try again if any luck will update and give the links
pasha543 said:
i already tried several times this method however no luck i am really not sure what to do any more i think only option try to find latest rom or first rom then try again if any luck will update and give the links
Click to expand...
Click to collapse
bump 4 help
(or is it hard brick)
Hi,
A2017G
Started with marshmallow,
Unlocked bootloader
attempted to install Slim7
seemed to work but with some possible errors, (wouldn't sync with google... retrospect I should have looked elsewhere before...)
attempted in install stock rom
using
ZTE_A2017GV1.2.0B04_BootStack_by_tron1.zip
ZTE_A2017GV1.2.0B04_Stock_System_by_tron1.zip
which wouldn't boot
So I tried reinstall Slim7
then stock again,
then, like the noob that I am, I removed twrp with
ZTE_A2017GV1.2.0B04_Full_Stock_Reverter_by_tron1.zip
which installs stock recovery
so, now I have a stock rom that won't boot,
an unlocked bootloader
and stock recovery
Not sure what to do from here
thanks in advance for any assistance.
I can abd sideload and update from SD card, but everything I have fails signature verification.
edit: so frustrating trying to find that 1 zip
Dizzee said:
(or is it hard brick)
Hi,
A2017G
Started with marshmallow,
Unlocked bootloader
attempted to install Slim7
seemed to work but with some possible errors, (wouldn't sync with google... retrospect I should have looked elsewhere before...)
attempted in install stock rom
using
ZTE_A2017GV1.2.0B04_BootStack_by_tron1.zip
ZTE_A2017GV1.2.0B04_Stock_System_by_tron1.zip
which wouldn't boot
So I tried reinstall Slim7
then stock again,
then, like the noob that I am, I removed twrp with
ZTE_A2017GV1.2.0B04_Full_Stock_Reverter_by_tron1.zip
which installs stock recovery
so, now I have a stock rom that won't boot,
an unlocked bootloader
and stock recovery
Not sure what to do from here
thanks in advance for any assistance.
Click to expand...
Click to collapse
Just use MiFlash, that one's guaranteed to work. Read my DFU unbrick guide to know how to use it. Just skip the part where you have to disassemble the phone, since you can get to EDL mode by (with the phone off and the USB cable connected to the PC) holding both volume buttons and inserting the USB-C cable to the phone.
I did read your guide, was, hoping to avoid dismantling it...
I tried pressing all 3 buttons.
Am I understanding the procedure correctly:
[phone switched off] + usb-C cable connected to PC only
MiFlash running at this point??
Hold both volume keys in and in insert Cable to Phone
at this point is the phone supposed to switch on?
At no point am I supposed to press the power button?
fyi: I will try different combinations, is great to have a solution, thank you.
Ah.... ok... so, the phone will display nothing, rely on the sound of PC and/or the device manager check and/or hit refresh on miflash
Fyi to anyone, if you have axon7toolkit installed and thus can't install a second version of MiFlash, open up the toolkit and hit 7 (unlock bootloader) to fire up MiFlash... or just go to C:\XiaoMi\XiaoMiFlash
the FULL_EDL file I have produces a couldn't find script Error when loading into MiFlash
so far when attempting to flash all zips
I have started MiFlash with admin
unzipped FULL_EDL file to a folder in root C:\ and ensured there are no spaces in address.
Every time / Every file produces couldn't find script error when loaded into MiFlash
when I attempt to flash the file it says cannot receive hello packet and then times out with an error
Tried disabling anti-virus/firewall, still same error
upgraded MiFlash to 2017.4.24.0 ( older 2016 is included with axon7toolkit), this removes the couldn't find script error, but still not receiving a hello packet, gunna fiddle with the phone as I'm pretty sure the error is coming from there
YES!
rebooted phone, turned off, restarted into EDL, flashed the stock rom from zte site... is in chinese... but it works. Thank you Thank you
so adventure over, after all that I am back to 6.0.1...
Dizzee said:
I did read your guide, was, hoping to avoid dismantling it...
I tried pressing all 3 buttons.
Am I understanding the procedure correctly:
[phone switched off] + usb-C cable connected to PC only
MiFlash running at this point??
Hold both volume keys in and in insert Cable to Phone
at this point is the phone supposed to switch on?
At no point am I supposed to press the power button?
fyi: I will try different combinations, is great to have a solution, thank you.
Ah.... ok... so, the phone will display nothing, rely on the sound of PC and/or the device manager check and/or hit refresh on miflash
Fyi to anyone, if you have axon7toolkit installed and thus can't install a second version of MiFlash, open up the toolkit and hit 7 (unlock bootloader) to fire up MiFlash... or just go to C:\XiaoMi\XiaoMiFlash
the FULL_EDL file I have produces a couldn't find script Error when loading into MiFlash
so far when attempting to flash all zips
I have started MiFlash with admin
unzipped FULL_EDL file to a folder in root C:\ and ensured there are no spaces in address.
Every time / Every file produces couldn't find script error when loaded into MiFlash
when I attempt to flash the file it says cannot receive hello packet and then times out with an error
Tried disabling anti-virus/firewall, still same error
upgraded MiFlash to 2017.4.24.0 ( older 2016 is included with axon7toolkit), this removes the couldn't find script error, but still not receiving a hello packet, gunna fiddle with the phone as I'm pretty sure the error is coming from there
YES!
rebooted phone, turned off, restarted into EDL, flashed the stock rom from zte site... is in chinese... but it works. Thank you Thank you
so adventure over, after all that I am back to 6.0.1...
Click to expand...
Click to collapse
What? It's in chinese?
Can you tell me the name of the file you used? Do you still have cell signal?
Choose an username... said:
What? It's in chinese?
Can you tell me the name of the file you used? Do you still have cell signal?
Click to expand...
Click to collapse
I got it from here: http://www.ztedevice.com/support
selected:- United Kingdom > Mobile Phone > Axon 7
it offers a file "AXON 7(ZTE A2017G) SD card software package(328540B2634ZTE A2017GV1.0.0B11)"
which hints at being compatible with A2017G... but is A2017V and is chinese, although you can change the language in settings there is still plenty here and there, plus chinese bloatware
and No, I didn't get cell signal.
I've gone back to Marshmellow, I will try again, didn't think it would be so different/difficult... Although wow at MiFlash.
FFS!!!! Relocked bootloader and bricked it!!! there should be a warning!
you gotta laugh,
I am a bit livid, I know the guides come with disclaimers, however, you'd think it would be an obvious important warning to make... DO NOT RELOCK YOUR PHONE.
FFS!
Dizzee said:
FFS!!!! Relocked bootloader and bricked it!!! there should be a warning!
you gotta laugh,
I am a bit livid, I know the guides come with disclaimers, however, you'd think it would be an obvious important warning to make... DO NOT RELOCK YOUR PHONE.
FFS!
Click to expand...
Click to collapse
Good lord...
You probably wiped out both IMEIs, now you relock out of the blue... Go to my DFU unbrick guide and stop doing dumb stuff :silly:
Choose an username... said:
Good lord...
You probably wiped out both IMEIs, now you relock out of the blue... Go to my DFU unbrick guide and stop doing dumb stuff :silly:
Click to expand...
Click to collapse
... after I finally got it working again (thanks for the assist), I thought relocking it was just making it secure again. I been rooting/unrooting and swapping out roms since the galaxy s2, who'd think you can't unlock and relock... I do think there should be warnings as it is too easy a mistake to make... lmao stop doing dumb stuff you start first
My phone is insured so I'm not overly fussed, but others will be less fortunate.
hello everywone...i have a troble to...my phone is A2017GV1.2.0B04 like this in post.
I bay this phone whit broken screen, i change the screen and try sim card but the phone is locked Whit google account... When I try my sim to test microphone, the phone it's work OK, but I unlock google account whit add tools and after that my phone don't have a service.
Phone tells no service or turned off airplane mode...what is not true... I can change the 4g/3g/2g connection to only 3g or something else... Wi-Fi and everything else work great but no service... The phone see what operator is on sim but no service... Somebody to help me please and tell me some tutorials how to fix?
I by this phone from Denmark and now I'm in Serbia... Eny help please
Thanks anyway Dragan
---------- Post added at 08:30 PM ---------- Previous post was at 08:27 PM ----------
Mistake,whit adb tools...
Good evening! I hope you can help me.
I flashed LineageOS 14.1, but I wanted to go back to EMUI. I made all the wipes and tried to flash different stock firmwares through a forced update (volume buttons + power button), but it never worked. At that point, I read about a guy in this forum who suggested to create a flashable zip with Huawei Update Extractor: I followed the suggestion and tried to flash it with TWRP. No error was given, but when I tried to restart, TWRP told me I had no OS installed. I thought it was strange, so I tried to restart anyway. That's when I got in rescue mode. I can't get into the recovery and I can't use fastboot. What rescue mode shows me is:
RESCUE MODE
Attention!
Please update system again
Update User Guide:
*link*
*android avatar*
Error!
Func NO: 10 (boot image)
Error NO: 2 (load failed!)
Pressing the three buttons, I'm able to force an update. The problem is I can't find a firmware that doesn't get rejected. With Lollipop firmwares, it starts to install, but it fails at 12%. With Marshmallow ones, the installation process doesn't even start.
What can I do to make it work again? I'm very sad because this phone was gifted to me a couple of days ago and I already messed it up. I don't even know how to turn it off.
What can I do to get in fastboot mode? At that point, what should I do to flash the stock firmware? Or maybe do I need to find the first stock firmware ever installed into this phone to make the forced update work?
Please, I need help. Thank you in advance!
P.S. The phone's model is ALE-L21. I live in Italy, so I assume it's a European version.
Did you managed to fix this?
Jhon_Locke said:
Did you managed to fix this?
Click to expand...
Click to collapse
Not yet, but I'm working on it. I found out that the device is recognized by my PC if I follow these steps:
1. Connect the phone to the PC and wait for it to go in rescue mode;
2. Wait until the notification LED stops to blink;
3. Disconnect the USB cable;
4. Press volume - and power button;
5. Reconnect the cable.
At that point, the screen turns black and the phone is recognized as "㌲㔴㜶㤸". I installed the drivers and now it's recognized as "HUAWEI USB COM 1.0". I should be able to reflash the partitions and make my phone work again, but I'm still trying to understand how to do it correctly.
Any help is appreciated!
ErikChimello said:
Not yet, but I'm working on it. I found out that the device is recognized by my PC if I follow these steps:
1. Connect the phone to the PC and wait for it to go in rescue mode;
2. Wait until the notification LED stops to blink;
3. Disconnect the USB cable;
4. Press volume - and power button;
5. Reconnect the cable.
At that point, the screen turns black and the phone is recognized as "㌲㔴㜶㤸". I installed the drivers and now it's recognized as "HUAWEI USB COM 1.0". I should be able to reflash the partitions and make my phone work again, but I'm still trying to understand how to do it correctly.
Any help is appreciated!
Click to expand...
Click to collapse
fastboot detects your device when you plug it into your computer?
I mean, if you run "fastboot devices" it shows your phone?
I've had this same problem but with an P8 Lite 2017, after flashing some ROM that supposedly was the stock one and trying to flash recovery I ended up with my phone bootlooping into rescue mode, I was able to "bypass" this thing rebooting my phone like crazy, seriously like after 20 reboot it finally booted into the damn ROM and I never touched the phone again. Sometimes when the phone ran out of battery and tried to power it on the phone booted into rescue mode and again after some reboots it booted to Android but now I want to install a custom ROM or at the very least root this damn phone so that's why I'm asking you if you have solved this, if you do then probably if I follow the same steps I would be able to fix that screen, hopefully.
If you are able to flash something start with flashing all recoveries your update.app has, maybe that's the problem (at least in my phone it is).
Jhon_Locke said:
fastboot detects your device when you plug it into your computer?
I mean, if you run "fastboot devices" it shows your phone?
I've had this same problem but with an P8 Lite 2017, after flashing some ROM that supposedly was the stock one and trying to flash recovery I ended up with my phone bootlooping into rescue mode, I was able to "bypass" this thing rebooting my phone like crazy, seriously like after 20 reboot it finally booted into the damn ROM and I never touched the phone again. Sometimes when the phone ran out of battery and tried to power it on the phone booted into rescue mode and again after some reboots it booted to Android but now I want to install a custom ROM or at the very least root this damn phone so that's why I'm asking you if you have solved this, if you do then probably if I follow the same steps I would be able to fix that screen, hopefully.
If you are able to flash something start with flashing all recoveries your update.app has, maybe that's the problem (at least in my phone it is).
Click to expand...
Click to collapse
No, it doesn't show anything if I write that command...
I guess mine won't ever boot into the rom because it seems like there's no system installed. I made some researches and found out there are some softwares that let you reflash the partitions IF the phone is recognized as "HUAWEI USB COM 1.0". I'm still trying to figure out how to do it correctly though. I feel like if I do something wrong, then my phone won't probably turn on again.
In your case, you should be able to flash a custom rom without any issue. You just have to be very careful and inform you as much as you can: I don't want your phone to end up like mine?. Anyway, it seems pretty hard to go back to the stock rom, so think about it before you flash a custom rom. Also, make a Nandroid Backup is very important.
Hi!
As in the title, something wrong with my P9 Lite happened. Namely, the day before yesterday he decided to turn off by himself with a 50% battery there, but turned on normally after 2minutes. At night from Wednesday to Thursday it discharged and in the morning after charging I couldn`t start it.
The phone either booted and stopped several times on the Huawei logo and the note "Powered by Android". I can enter by using a key combination the eRecovery mode. Ultimately, it started up one time, and it worked until the evening and until it was discharged again. After that it has been charged to 60%, one time he turned on but after an hour of further charging he fell on the amen. I've been trying to fight him since the morning that maybe he'll turn on like yesterday, but no. I had this situation for the first time in August 2018, then in February and July 2019 with that it was probably a decent brick then, because this black screen was constantly displayed with an exclamation mark and some error. A visit in smartphone service has always helped, but I can't spend 80 PLN again to fix that issue. After the repair in July, I specially wrote the system version so that I would have knowledge for the future in the event of a repeat. The phone had the firmware as below:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Today I downloaded the system from this link: huawei-firmware.com/rom/huawei-p9-lite/vns-l21/9618
However, at 5% installation the error crashes and I can only restart the phone. I tried using two different sd cards, so the option of the card being faulty is 99% out of the question. I hope that some good soul will help me, because I believe that I can solve this problem independently at home and not necessarily after paying with a GSM spec. : P
I forgot to add that the phone has not been updated since it was repaired or anything. I didn't do any treatments myself with loading custom systems. He just turned himself off, without any previous signs of malfunction and end. I was surprised that the phone doesn`t want to accept the software that was uploaded by a service technician ... but maybe I am doing something wrong.
At the end fastboot situation:
PHONE: unlocked
FRP: locked
EDIT:
In another forum I got instructions to upload rollback and then soft "C432B160" and everything will be good. I took it up and the rollback installation was completed, after a minute the phone rebooted. Unfortunately, this problem caused another problem, because since I installed rollback I can`t enter the erecovery mode, where I have possibility to shut down...so phone stuck with the Huawei logo all the time. I was supposed to upload this software, but I had to leave the house and the phone was completely discharged when I returned. From that moment only fastboot mode starts, or after switching on and trying with different phone buttons, it always becomes a logo and got freezed. I was charging it for an hour, but after disconnecting from the charger the LED was blinking red and I saw on the screen message about 0% battery. After that another situation...I connected it to the charger and after a second showed me message of 100% battery, but after a second phone started automatically and hung on the logo again. After unplugging it from charger and trying to start without charging, the LED flashes red and message about disscharge was on the screen. Now I`m seriously starting to wonder, if anything from this phone will still be..... :/
Links to rollback and software (according to which I did not manage to upload before discharging the phone):
http://download-c1.huawei.com/downlo...00&siteCode=pl
http://huawei-firmware.com/rom/huawei-p9-lite/vns-l21/9571
Nicramcio said:
Hi!
As in the title, something wrong with my P9 Lite happened.
Namely, the day before yesterday he decided to turn off by himself with a 50% battery there, but turned on normally after 2minutes. At night from Wednesday to Thursday it discharged and in the morning after charging I couldn`t start it.
The phone either booted and stopped several times on the Huawei logo and the note "Powered by Android". I can enter by using a key combination the eRecovery mode. Ultimately, it started up one time, and it worked until the evening and until it was discharged again. After that it has been charged to 60%, one time he turned on but after an hour of further charging he fell on the amen. I've been trying to fight him since the morning that maybe he'll turn on like yesterday, but no. I had this situation for the first time in August 2018, then in February and July 2019 with that it was probably a decent brick then, because this black screen was constantly displayed with an exclamation mark and some error. A visit in smartphone service has always helped, but I can't spend 80 PLN again to fix that issue. After the repair in July, I specially wrote the system version so that I would have knowledge for the future in the event of a repeat. The phone had the firmware as below:
Today I downloaded the system from this link: huawei-firmware.com/rom/huawei-p9-lite/vns-l21/9618
However, at 5% installation the error crashes and I can only restart the phone. I tried using two different sd cards, so the option of the card being faulty is 99% out of the question. I hope that some good soul will help me, because I believe that I can solve this problem independently at home and not necessarily after paying with a GSM spec. : P
I forgot to add that the phone has not been updated since it was repaired or anything. I didn't do any treatments myself with loading custom systems. He just turned himself off, without any previous signs of malfunction and end. I was surprised that the phone doesn`t want to accept the software that was uploaded by a service technician ... but maybe I am doing something wrong.
At the end fastboot situation:
PHONE: unlocked
FRP: locked
EDIT:
In another forum I got instructions to upload rollback and then soft "C432B160" and everything will be good. I took it up and the rollback installation was completed, after a minute the phone rebooted. Unfortunately, this problem caused another problem, because since I installed rollback I can`t enter the erecovery mode, where I have possibility to shut down...so phone stuck with the Huawei logo all the time. I was supposed to upload this software, but I had to leave the house and the phone was completely discharged when I returned. From that moment only fastboot mode starts, or after switching on and trying with different phone buttons, it always becomes a logo and got freezed. I was charging it for an hour, but after disconnecting from the charger the LED was blinking red and I saw on the screen message about 0% battery. After that another situation...I connected it to the charger and after a second showed me message of 100% battery, but after a second phone started automatically and hung on the logo again. After unplugging it from charger and trying to start without charging, the LED flashes red and message about disscharge was on the screen. Now I`m seriously starting to wonder, if anything from this phone will still be..... :/
Links to rollback and software (according to which I did not manage to upload before discharging the phone):
http://download-c1.huawei.com/downlo...00&siteCode=pl
http://huawei-firmware.com/rom/huaw...
Your device is natively single or dual sim ?
Click to expand...
Click to collapse
Dadditz said:
Hey dude, let me know if i understood well...
Your device won't boot up anymore, isn't it ?
VNS-L21C432B120 ?? It's one of the oldest firmware you can have..
I really don't know if i can help, but if you agree we can give a try..
Your device is natively single or dual sim ?
Click to expand...
Click to collapse
Yas, my device won`t boot up since 1st of July and I don`t know why...because I don`t tried to update firmware, unlock bootloader etc.
I know that, but year ago I have a same problem and GSM service installed that soft.
My device is dual sim.
Thanks for help!
Nicramcio said:
Yas, my device won`t boot up since 1st of July and I don`t know why...because I don`t tried to update firmware, unlock bootloader etc.
I know that, but year ago I have a same problem and GSM service installed that soft.
My device is dual sim.
Thanks for help!
Click to expand...
Click to collapse
Ok let's go..
Take a working (at least 4gb) SD,
move away all your stuff then format it as FAT32.
Download this >> update.zip << file (VNS-L21C432B160/dual sim).
Unzip it, you find UPDATE.APP file.
Turn off the phone.
On your PC create a folder and rename it DLOAD.
Copy/paste (only) UPDATE.APP file into DLOAD folder
and put it into SD, then insert the SD into your device.
Turn the device on keeping vol+ & vol- then power button
all together till an update screen appears.
Ok, release now the buttons...
After the flashing process, your device should reboot to system.
If passes over 15 mins, reboot into the e-recovery
(press vol+ & power button) and do a factory reset + wipe cache.
Done !!
NOTE: the firmwrare link is taken using Firmware Finder repo,
all credits go to this fantastic app team/users that created it.
Dadditz said:
Ok let's go..
Take a working (at least 4gb) SD,
move away all your stuff then format it as FAT32.
Download this >> update.zip << file (VNS-L21C432B160/dual sim).
Unzip it, you find UPDATE.APP file.
Turn off the phone.
On your PC create a folder and rename it DLOAD.
Copy/paste (only) UPDATE.APP file into DLOAD folder
and put it into SD, then insert the SD into your device.
Turn the device on keeping vol+ & vol- then power button
all together till an update screen appears.
Ok, release now the buttons...
After the flashing process, your device should reboot to system.
If passes over 15 mins, reboot into the e-recovery
(press vol+ & power button) and do a factory reset + wipe cache.
Done !!
NOTE: the firmwrare link is taken using Firmware Finder repo,
all credits go to this fantastic app team/users that created it.
Click to expand...
Click to collapse
Thank you, but I tried to install by dload method some kind of softwares B120,130,150,160 if I remember...but no effects. In other forum, they said that I need to install rollback, and after that firmware B160. Ok, I installed rollback perfectly but after that I can`t go to erecovery mode...only fastboot is avaliable and whene I turn on phone it would stuck on Huawei logo. Now it`s discharged and i don`t have any idea how can i charged it to over 30% of battery.
Nicramcio said:
Thank you, but I tried to install by dload method some kind of softwares B120,130,150,160 if I remember...but no effects. In other forum, they said that I need to install rollback, and after that firmware B160. Ok, I installed rollback perfectly but after that I can`t go to erecovery mode...only fastboot is avaliable and whene I turn on phone it would stuck on Huawei logo. Now it`s discharged and i don`t have any idea how can i charged it to over 30% of battery.
Click to expand...
Click to collapse
Dude if there is some hardware problem
it will be a little difficult to recover..
so when you bringed it to service have they replaced the motherboard?
If not you may still have hardware problems, but let's keep this aside ...
Try again what i wrote..
In the meantime I give you the correct rollback link, maybe you used the wrong one.
Dude, the rollback package is used only to revert from android 7 to android 6.
In order to unbrick the device, in android 6 environment, dload method is enough..
Visit the UNIFIED HELP THREAD, post #6, see by yourself..
Dadditz said:
Dude if there is some hardware problem
it will be a little difficult to recover..
so when you bringed it to service have they replaced the motherboard?
If not you may still have hardware problems, but let's keep this aside ...
Try again what i wrote..
In the meantime I give you the correct rollback link, maybe you used the wrong one.
Dude, the rollback package is used only to revert from android 7 to android 6.
In order to unbrick the device, in android 6 environment, dload method is enough..
Visit the UNIFIED HELP THREAD, post #6, see by yourself..
Click to expand...
Click to collapse
I know it`s some kind of big problem.
3 times it was unbricked in service, but that is non authorized and they don`t do anything with motherboard...only installed me somehow new software for money circa 20 USD/EUR.
Okay i`ll try that tomorow and show results. I keep my fingers crossed, that my Huawei tomorow boot normal.
Nicramcio said:
I know it`s some kind of big problem.
3 times it was unbricked in service, but that is non authorized and they don`t do anything with motherboard...only installed me somehow new software for money circa 20 USD/EUR.
Okay i`ll try that tomorow and show results. I keep my fingers crossed, that my Huawei tomorow boot normal.
Click to expand...
Click to collapse
Sorry, i forgot to add the LINK to correct rollback package,
here you are..
Cheers
Edit: next time, maybe tomorrow i will post how to extract
firmware (BOOT,RECOVERY,SYSTEM) from UPDATE.APP
and how to flash it via fastboot commands.
Dadditz said:
Sorry, i forgot to add the LINK to correct rollback package,
here you are..
Cheers
Edit: next time, maybe tomorrow i will post how to extract
firmware (BOOT,RECOVERY,SYSTEM) from UPDATE.APP
and how to flash it via fastboot commands.
Click to expand...
Click to collapse
I don`t have time to do something with my bricked phone over a week, but today I tried to install software B160 and rollback by dload mode. It didn`t work. I can`t charge my phone over 30% of battery, and when I plug off the charger, phone have probably not enough battery to turn software installation. Also when I tried to hold 3 buttons, and then connected the charger cable...the installation didn`t start. So I think, that you must tell me how to flash soft via fastboot commands...because this is the only one mode that I can turn on my phone. I feel completely helpless, because today my replacement phone broke...so I have to bring Huawei back to life.
EDIT:
I forgot to mentioned...When i hold 3 buttons to start installation process phone vibrate one, then shown red lightning sign that battery is empty, and LED flashed 3 times red...then screen go black and device is powered off...nothing else. Also I tried 4 different SD cards, so I think now the problem with dload mode is that phone is not charged over 30 or 50% (I don`t remeber that) of battery what is required to start the installation process.
Also when I try to charge it, only LED flashes red all the time and on the screen I don`t have information that phone is charging.
Nicramcio said:
I don`t have time to do something with my bricked phone over a week, but today I tried to install software B160 and rollback by dload mode. It didn`t work. I can`t charge my phone over 30% of battery, and when I plug off the charger, phone have probably not enough battery to turn software installation. Also when I tried to hold 3 buttons, and then connected the charger cable...the installation didn`t start. So I think, that you must tell me how to flash soft via fastboot commands...because this is the only one mode that I can turn on my phone. I feel completely helpless, because today my replacement phone broke...so I have to bring Huawei back to life.
EDIT:
I forgot to mentioned...When i hold 3 buttons to start installation process phone vibrate one, then shown red lightning sign that battery is empty, and LED flashed 3 times red...then screen go black and device is powered off...nothing else. Also I tried 4 different SD cards, so I think now the problem with dload mode is that phone is not charged over 30 or 50% (I don`t remeber that) of battery what is required to start the installation process.
Also when I try to charge it, only LED flashes red all the time and on the screen I don`t have information that phone is charging.
Click to expand...
Click to collapse
Hi dude,
I suspect your device has some serious hardware problem.
If the device has fallen off, it may have broken or unstuck / unsoldered something,
hence the need for a check by specialized technicians / service point.
I suggest, if you have the possibility,
to replace the device with a new or even used one,
functioning and a little more updated / upgradeable.
But trying won't cost anything, so let's do it !!!
Make sure you have minimal adb & fastboot
or a complete platform-tools (link in the same page / it's your choise)
and huawei drivers /HiSuite on your PC,
then in fastboot mode do the command > fastboot devices.
If you have a response like > numbers/letters........device <
then you're ok to go, otherwise it means your PC don't "see" your phone...
From XDA download Huawei Update Extractor and use it
to extract BOOT.img, RECOVERY.img (not RECOVERY2.img)
and SYSTEM.img from your UPDATE.APP file
you extracted from update.zip...(see attachment)
Put those three files into a folder and rename it as you want
(maybe the same where you extracted UPDATE.APP),
then tap in the folder address bar (see attachment) and type cmd then hit enter.
A command window will appears, now you're ready to flash.
In order type following commands:
1 - fastboot flash boot BOOT.img; (let it flash)
2 - fastboot flash recovery RECOVERY.img; (let it flash)
3 - fastboot flash system SYSTEM.img; (let it flash)
Once finished type > fastboot reboot and cross your fingers...
If all will take right direction your device will reboot correctly,
otherwise (if passes over 15 mins) reboot recovery (vol+ & power buttons)
and do a factory reset..
Hope sincerely it will boot up... :angel:
P.S.: I don't know why i can't post jpg directly, so i zipped into one file...
Dadditz said:
Hi dude,
I suspect your device has some serious hardware problem.
If the device has fallen off, it may have broken or unstuck / unsoldered something,
hence the need for a check by specialized technicians / service point.
I suggest, if you have the possibility,
to replace the device with a new or even used one,
functioning and a little more updated / upgradeable.
But trying won't cost anything, so let's do it !!!
Make sure you have minimal adb & fastboot
or a complete platform-tools (link in the same page / it's your choise)
and huawei drivers /HiSuite on your PC,
then in fastboot mode do the command > fastboot devices.
If you have a response like > numbers/letters........device <
then you're ok to go, otherwise it means your PC don't "see" your phone...
From XDA download Huawei Update Extractor and use it
to extract BOOT.img, RECOVERY.img (not RECOVERY2.img)
and SYSTEM.img from your UPDATE.APP file
you extracted from update.zip...(see attachment)
Put those three files into a folder and rename it as you want
(maybe the same where you extracted UPDATE.APP),
then tap in the folder address bar (see attachment) and type cmd then hit enter.
A command window will appears, now you're ready to flash.
In order type following commands:
1 - fastboot flash boot BOOT.img; (let it flash)
2 - fastboot flash recovery RECOVERY.img; (let it flash)
3 - fastboot flash system SYSTEM.img; (let it flash)
Once finished type > fastboot reboot and cross your fingers...
If all will take right direction your device will reboot correctly,
otherwise (if passes over 15 mins) reboot recovery (vol+ & power buttons)
and do a factory reset..
Hope sincerely it will boot up... :angel:
P.S.: I don't know why i can't post jpg directly, so i zipped into one file...
Click to expand...
Click to collapse
Oh men i appriciate that you wrote everything. Only one problem, I can`t download the zipped file. :/ Also I keep in mind another type of solution for my Huawei, but more on that later. Now I gonna try to flash software by fastboot my hero.
EDIT: beginning gone well
EDIT2: commands not work properly. I done everything like you told me, but you can see error in cmd (cmd is enabled as administrator).
I download adb from this tutorial:
https://www.youtube.com/watch?v=OKRTbv-6Kzc
because previous didn`t work.
As you can see I typed "fastboot flash boot BOOT.img" as you told me, but I get info FAILED. :/
Searched for information and I found, that I need to unlock bootloader once again...and after that every command should work.
Nicramcio said:
I download adb from this tutorial:
https://www.youtube.com/watch?v=OKRTbv-6Kzc
because previous didn`t work.
As you can see I typed "fastboot flash boot BOOT.img" as you told me, but I get info FAILED. :/
Searched for information and I found, that I need to unlock bootloader once again...and after that every command should work.
Click to expand...
Click to collapse
Good work dude.
I previously readed on your post
phone = unlocked
frp = locked
i was thinking you was ready to flash
but evidently that was not correct...
For some unknown reason i cannot post
screenshots so i decided to add them on postimage...
As you can see they are quite same as yours...
https://i.postimg.cc/fTNZvWY9/VNS-L21-C432-B160.jpg
https://i.postimg.cc/x1s2YKhv/Extractor-select-your-update-app-file.jpg
https://i.postimg.cc/5t6MtXWZ/extract-BOOT-RECOVERY-SYSTEM.jpg
https://i.postimg.cc/LswFgmHh/open-command-window2.jpg
Let me know how the work goes on ...
Cheers
Dadditz said:
Good work dude.
I previously readed on your post
phone = unlocked
frp = locked
i was thinking you was ready to flash
but evidently that was not correct...
For some unknown reason i cannot post
screenshots so i decided to add them on postimage...
As you can see they are quite same as yours...
https://i.postimg.cc/fTNZvWY9/VNS-L21-C432-B160.jpg
https://i.postimg.cc/x1s2YKhv/Extractor-select-your-update-app-file.jpg
https://i.postimg.cc/5t6MtXWZ/extract-BOOT-RECOVERY-SYSTEM.jpg
https://i.postimg.cc/LswFgmHh/open-command-window2.jpg
Let me know how the work goes on ...
Cheers
Click to expand...
Click to collapse
Grazie molto!
I done everything with software, step by step just like in your images...
...but again no working commands.
I`ve got only info in CMD that FAILED (remote: Command not allowed).
In other threads I menaged to get info that,
if phone has never been rooted and get custom ROM the bootloader is not unlocked and I need to relock it.
The threads are old and then you have to get a special code from Huawei site,
and then tap fastboot oem unlock "special number" or something like that.
Now I don`t know how to get that code and is there any way to try unlock bootloader and take a step forward?
Yas, we done step forward tomorrow because we know that PC see my device correctly,
we have good firmware but CMD commands caused another problem. :/
Nicramcio said:
Grazie molto!
I done everything with software, step by step just like in your images...
...but again no working commands.
I`ve got only info in CMD that FAILED (remote: Command not allowed).
In other threads I menaged to get info that,
if phone has never been rooted and get custom ROM the bootloader is not unlocked and I need to relock it.
The threads are old and then you have to get a special code from Huawei site,
and then tap fastboot oem unlock "special number" or something like that.
Now I don`t know how to get that code and is there any way to try unlock bootloader and take a step forward?
Yas, we done step forward tomorrow because we know that PC see my device correctly,
we have good firmware but CMD commands caused another problem. :/
Click to expand...
Click to collapse
Due to the conditions your device is in,
I don't know if you can unlock the bootloader.
To read the code you can use DC-Unlocker
(PC or smartphone versions), buy credits for € 4 and try.
The risk is that if it doesn't work, you throw away your money.
A user HERE suggested the idea of using a method
a little more spartan and without money,
but honestly I have never tried it and you could physically break something ...
The choice remains yours, keep me informed for future developments.
P.S .: Bardzo dziękuję za opinię ...
Dadditz said:
Due to the conditions your device is in,
I don't know if you can unlock the bootloader.
To read the code you can use DC-Unlocker
(PC or smartphone versions), buy credits for € 4 and try.
The risk is that if it doesn't work, you throw away your money.
A user HERE suggested the idea of using a method
a little more spartan and without money,
but honestly I have never tried it and you could physically break something ...
The choice remains yours, keep me informed for future developments.
P.S .: Bardzo dziękuję za opinię ...
Click to expand...
Click to collapse
Ciao!
I`ve tried to use this spartan method...but all that nordic combinations were useless...because I still have fake unlocked bootloader. I`ve decided that motherboard in my phone is a piece of **** and merda, so I`ll buy a little damaged phone. The cost of it is 27EUR, so it`s around DC-Unlocker+DC-Phoenix...but I`ll get a device that work properly and have some scratches.
I don`t want to spend money to my damage and dumping motherboard...because I have done this in the past 3 times (the cost of these repairs are around 60EUR). If I had enough knowledge that my motherboard will break down regularly in the future, I`ll buy used P9 Lite much much earlier.
https://allegro.pl/oferta/huawei-p9-lite-lekkie-pekniecie-prawy-gorny-rog-9523407957
Thanks you all, because we tried a lot of methods and solutions! I'm really thankful for all help!
Grazie mille Dadditz mio eroe. Ciao ragazzo! :laugh:
Nicramcio said:
Ciao!
I`ve tried to use this spartan method...but all that nordic combinations were useless...because I still have fake unlocked bootloader. I`ve decided that motherboard in my phone is a piece of **** and merda, so I`ll buy a little damaged phone. The cost of it is 27EUR, so it`s around DC-Unlocker+DC-Phoenix...but I`ll get a device that work properly and have some scratches.
I don`t want to spend money to my damage and dumping motherboard...because I have done this in the past 3 times (the cost of these repairs are around 60EUR). If I had enough knowledge that my motherboard will break down regularly in the future, I`ll buy used P9 Lite much much earlier.
https://allegro.pl/oferta/huawei-p9-lite-lekkie-pekniecie-prawy-gorny-rog-9523407957
Thanks you all, because we tried a lot of methods and solutions! I'm really thankful for all help!
Grazie mille Dadditz mio eroe. Ciao ragazzo! :laugh:
Click to expand...
Click to collapse
I am in complete agreement with you, you made the right choice.
I was very happy to try to help you, especially because
you are a polite and kind person.
I hope to meet again in the future, but not for device's issues ... :highfive:
I wish you all the best.
Regards
stuck on 5% , software install failed, getting package info error
i used huawei p9 lite vns L22 dual sim , device has got failed verfication ,asking for update latest version, then its stuck on 5% .software install failed, i have a poor knowledge about techniqal issues, please help me out