Related
Hello Atrix owners,
(jump to "The ideas" if you dont want to hear my story! )
Got my Atrix at&t last friday, still tweaking it to my likings, but when I started playing Apparatus, emulators, AirAttackHD, and other games to test the power of the TEGRA chip, I felt the phone becoming warmer and warmer.
EDIT: Played 1 lap on Riptide, went to check on the processor temp: 61 degrees celsius.
I opened the back case. The bottom area, specially above the microSD card, was very hot (based on motorola defy's temps, my previous android phone)
The battery itself wasn't even warm, except for the region near the bottom left.
I was scared I had gotten a defective unit, so I came to xda forums, and most of the topics related to temps came to the same conclusion: that was the normal operating temps under load from the dual core processor.
Still, it worries me because of the position in which they've placed the microSD port. My card's max. operating temps are 60 celsius, and my processor was doing 52 within 5-10 minutes of gaming.
Also, I'm a little obsessed with computer components getting too hot. I've seen lots of motherboards leaving this world because of that.
The ideas:
Since I had recently bought a ICDiamond thermal paste, I started thinking about modding the atrix's case to dissipate more heat, someway.
This page shows a teardown of our phone: http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/2
You can see in the board's pictures that the NVIDIA CPU/GPU chip along with the 1gb memory its exactly above the microSD slot - marked in yellow in STEP 10
I was thinking about removing the metal plate covering the chip itself, apply some thermal paste there that would transfer heat to the metal plate. (see picture)
Then, above the metal plate, on the plastic cover shown in this picture, maybe put a small copper sheet (or other heat conducting material) on the inside, to spread the heat to a larger area.
Maybe drill some holes on the plastic cover to expose this metal to the area just under back cover.
One concern (also shown in the picture and in the website) is the magnetic compass, marked blue on the attached pic. Would the metal sheet cause any kind of interference? I could use some help on this from someone with more knowledge on magnetic physics and eletronic compasses.
I haven't done any sorts of thermal modding on computers, graphics cards, etc., so I would like some help, insights, and improves on my initial ideas, so we can have cooler dual core smartphones
Nice post! I'm curious to see some reviews after some other brave souls try this... In theory it should help. As for the magnetic compass.... maybe try using aluminum foil... non magnetic, and will dissipate some heat... probably not as much as the copper, but hey....
This mod would be spreading out the heat from the CPU to about an inch away, but still in the phone, so what's the plan after that? Even without this mod, after maybe 10 minutes the bottom half of the phone is nice and warm under CPU-stressful activities anyway, there doesn't seem to be much need for more heat spreading ability... The heat spreads out fine, the real problem is getting heat away from the phone itself, not from the CPU.
Nice concept.
Drilling some small holes in the cover could help heat get out, but without active cooling, I doubt much will dissipate through there. If you were to drill holes, I would do them on a small CNC mill if you have one available so you get a nice even hole pattern, and minimize a drill wandering and butchering the cover. You could also cut a small piece out of the cover, then put some wire mesh like the speaker cover over it to get more air in/out.
You will be fine using metal sheeting if you do not use anything magnetic. But then the materials available will probably not conduct heat very well.
In all reality, as I previously said, without any kind of active cooling, you may pull a few degrees of heat away from the CPU/GPU, but then it has nowhere to go from there, so I doubt you will gain much.
Only one way to find out for sure though!
Hello WolfFX, my fellow atrix owner,
Nice idea indeed. I would probably prefer to stick a very thin layer of copper on top of the current one and apply the paste between the two copper. If the results seem to better than stock, i would use correct sandpaper to create more space in the housing, so i could put a thicker copper plate. Thicker copper means better heat spreading and cooling.
I had 2 defy's myself. The reason for the defy spreading heat better cause its internal design isn't as complicated as atrix plus its thicker. Generally, the singlecore cpu's can also get very hot if they're used in a thin housing IMO.
I use some on the base of a small fan that hooks up to my micro usb port for active. If you've read this far I am kidding and its not possible because the usb port is not.powered.
On another not cutting out approximately 1-1.5 square inches in lower part of the back cover and replacing with copper might help. Cutting out a hole/holes in the back of tpu case would help hold copper plate and let heat dissipate. It would be ghetto fabulous but the question is would it dissipate enough heat to make it worth the trouble.
I voided my warranty and your mum.
Dual core machines have to work harder in an environment designed for single core like Android. If the app you are running is optimised for dual core it should run cooler. ICS will be multi-core optimised. Dual core naturally run hotter than single.
Sent from my MB860 using xda premium
dragon_76 said:
Dual core machines have to work harder in an environment designed for single core like Android. If the app you are running is optimised for dual core it should run cooler. ICS will be multi-core optimised. Dual core naturally run hotter than single.
Sent from my MB860 using xda premium
Click to expand...
Click to collapse
Kinda funny that the idiots on Engaget constantly crave for quad-core, when we are struggling as it is on dual-core technology with single core FW...
Sent from my MB860 using XDA Premium App
palmboy5 said:
This mod would be spreading out the heat from the CPU to about an inch away, but still in the phone, so what's the plan after that? Even without this mod, after maybe 10 minutes the bottom half of the phone is nice and warm under CPU-stressful activities anyway, there doesn't seem to be much need for more heat spreading ability... The heat spreads out fine, the real problem is getting heat away from the phone itself, not from the CPU.
Click to expand...
Click to collapse
I tought about that, and you are right, it will still be warm.
But if the copper works, the processor temperature readings will be lower, while the warmth will have more area to be dissipated.
It will still be passive, but better than the actual state.
Does anybody have knowledge about motorola's warranty on the Atrix?
Supposing I would open the phone to put the copper and thermal paste, (but dont drill the case, that would be irreversible), would that void any warranty stickers or something like that?
I got my phone last friday, haven't unlocked bootloader or anything because I'd like to keep my warranty for a while...
ccrows said:
Kinda funny that the idiots on Engaget constantly crave for quad-core, when we are struggling as it is on dual-core technology with single core FW...
Sent from my MB860 using XDA Premium App
Click to expand...
Click to collapse
If people were satisfied with what exists, there would be no innovation.
Not saying increasing core count is innovative, but its far better than being stagnant nonetheless.
WolfFX said:
I tought about that, and you are right, it will still be warm.
But if the copper works, the processor temperature readings will be lower, while the warmth will have more area to be dissipated.
It will still be passive, but better than the actual state.
Does anybody have knowledge about motorola's warranty on the Atrix?
Supposing I would open the phone to put the copper and thermal paste, (but dont drill the case, that would be irreversible), would that void any warranty stickers or something like that?
I got my phone last friday, haven't unlocked bootloader or anything because I'd like to keep my warranty for a while...
Click to expand...
Click to collapse
what do you think? would you want to honor a warranty after making hardware changes like that? if you really want to try, buy a phone off craigslist with a broken screen or something and do the mod and see what happens.
pukemon said:
what do you think? would you want to honor a warranty after making hardware changes like that? if you really want to try, buy a phone off craigslist with a broken screen or something and do the mod and see what happens.
Click to expand...
Click to collapse
If someday I move from Brazil to United States I can think about your suggestions.
The damn taxes on my country make the carrier free phone cost equivalent to 1250 dollars.
The broken screen phone here probably will cost the same as a new one on US...
Whatever, soon I will lose my extreme-obsessive-care-for-new-gadget and unlock the bootloader, void the warranty, and test this mod.
If anyone has the courage to do it, please take some pics and post them here, along with comments
If you ever do it, I suggest slotting/drilling the back cover first and seeing what gains you.
I voided my warranty and your mum.
palmboy5 said:
If people were satisfied with what exists, there would be no innovation.
Not saying increasing core count is innovative, but its far better than being stagnant nonetheless.
Click to expand...
Click to collapse
I understand the need to innovate but...
IMO we are not at the point with CPUs where we can "comfortably" put 4 cores on phones yet.
Can it be done? yes, but it would be dumb to do IMHO. We need smaller transistors on chips, an OS that can handle multi-core, and devs that can write Apps properly for that.
Otherwise you're wasting money on an oven that happens to make calls...
Sent from my MB860 using XDA Premium App
pukemon said:
If you ever do it, I suggest slotting/drilling the back cover first and seeing what gains you.
Click to expand...
Click to collapse
By back cover you mean the one with torx screws, or the outer one?
To do it on the external cover I would need some fine tools, since any mistakes would screw even more the visual appeal of the phone
I saw on another topic here on the forums where someone was asking if there was something such as a metal back cover. That could help on the heat issue. But all the answers were negative. The flexibility of the plastic seems to be what allows it to be opened in the first place
ccrows said:
I understand the need to innovate but...
IMO we are not at the point with CPUs where we can "comfortably" put 4 cores on phones yet.
Can it be done? yes, but it would be dumb to do IMHO. We need smaller transistors on chips, an OS that can handle multi-core, and devs that can write Apps properly for that.
Otherwise you're wasting money on an oven that happens to make calls...
Sent from my MB860 using XDA Premium App
Click to expand...
Click to collapse
That and the fact you would need a much larger battery to make it a day, or stay with the thin is in but haved a wired cell phone because you wont go anywhere for long with a dead cell phone.
I voided my warranty and your mum.
like CaelanT said, without active cooling (read: a fan), there really will not be much benefit. the entire casing is made of plastic so even if heat were to be dissipated under that area, it would still be trapped there.
dLo GSR said:
like CaelanT said, without active cooling (read: a fan), there really will not be much benefit. the entire casing is made of plastic so even if heat were to be dissipated under that area, it would still be trapped there.
Click to expand...
Click to collapse
Wont dissipate too much, but the fact that we can feel the warmth outside means heat is coming through. I'll wait my tests week to be over so I can buy some tools and still need to find out where to buy the copper or aluminum sheet.
WolfFX said:
Wont dissipate too much, but the fact that we can feel the warmth outside means heat is coming through. I'll wait my tests week to be over so I can buy some tools and still need to find out where to buy the copper or aluminum sheet.
Click to expand...
Click to collapse
heat is coming through but it has nothing to remove it. we can heat sink it to another part of the phone but without a HUGE piece of heat conductive metal to take it, it will simply stay hot. there is no fan/active element to remove the heat from the device and so we are stuck with how it is. that's the problem with microelectronics and ICs that don't allow for fans, and it's up to the software and its use of the CPU to minimize the load on the processors.
i know the effort is valiant but i honestly, from an EE standpoint, don't see you getting much noticeable difference without cramping something else up (i.e. messing with reception because of rogue metal plates or transferring that heat to other parts / ICs of the phone which are not as heat resistant)
yes im sure this definetly voids warrenty (fyi lol i voided mine )
unlocked bootloader att. atrix. honeycomb rom. faux oc kernal
Hi all,
I have recently been repairing iphones and while doing this I have notice something in their construction that I thought we should have. Both the iphone 3 and 4 have a mylar mirror coating on the rear of the LCD to reflect heat away from the lcd and touchscreen, and it really works well. If you have an Iphone check it out, even when the cpu is flying the back gets hot but the screen stays cool. This got me thinking about the vega and how hot it gets running roms like VegaICS and Vegacomb. This can make touchscreens wig out and is uncomfortable. The design is flawed. There is a Mylar sheet in the vega but its completly in the wrong place. It is in the right place to be an RF sheild (thats probably what its for) but for cooling its about as much use as a 3 bar fire. When I am using my vega (playing games) it gets so hot inside that I can feel the heat flowing out of the hole for the dock connector. If I lay back, with the bottom of the vega resting on my stomach and I have a tee shirt on it gets hot enough to become uncomfortable so I have to move it. The Mylar sheet stuck to the back of the vega is reflecting heat back at the motherboard LCD and touchscreen like a little oven. The only place for the heat to escape is through the LCD, touchscreen and the other small gaps and holes around the vega. The metal panel bettween the LCD and motherboard will slow down the heating of the touchscreen but not much and will probably just be trapping heat when it gets up to temperature.
So to cool down the vega.
This is really simple. I ordered a small sheet of dimple mylar off eBay (non-conductive and disapates heat better than normal mylar preventing heat spots. apparently. I have put it under the motherboard and on the back of the LCD. I also removed the mylar from the back of the rear panel. For good measure I cut a pieces of aluminum off a PC heat sink and fixed them to the Tegra chip and the ram chips (with alaska sheet type heat sink stuff, that's a technical term ). The heat sinks are probably overkill but it cant hurt and may meen overclocking will be cooler and therfore more stable.
I tested it with and without the heat sinks and the overall temperature is significantly cooler on both. The screen now stays cool all the time, even when charging and using the cpu hard. The back still gets warm but no where near as hot as before. With the Addition of the heat sinks didn't noticably reduce the temperature but they will come into play when ICS gets overclocked.
A nice side effect is the charger no longer causes the touchscreen to freak out (altough this could be eduardo's new driver). Fine accuracy is reduced while plugged in but the screen no longer double/phantom clicks and is usable for everything but drawing.
Overall I am really happy with the mod. It's cheap and easy to do and cools the vega a lot. Next time I have the back off I may add another peice near the charge jack to try to completly remove the charge/accuracy problem. I have not noticed any problems with interferance caused by removing the mylar off the inside of the back panel although my neibours telly could be going haywire without me knowing (not my problem).
Heres some pictures of what I did.
The back of the LCD covered with mylar (hard to get a good picure because of the reflection.
The metal panel back in with more mylar where the battery and motherboard are mounted, holes cut in mylar for the motherboard mounting screws.
Everything back in except the battery.
This show the original mylar sheet and where it was inside the back panel. Now removed and binned.
The heat sinks
Running as cool as a cucumber B)
Amazing work, i have a Ployer Momo9, well it's more like a clone of that tablet, when i updated it to ICS it went ok, but sometimes i had random crashes, i used to have a small flat heatsink from an old motherboard wich still had the self-adhesive; so one day i finally gutted up and cracked open the tablet, placed the heatsink and had to say that now it doesn't crash.
I started googling to see if some1 had done the same with other tablet, i found your post and now i guess ill try the same with the mylar, wich can't find by the way, i have some aluminum sheet but i guess it's a bad idea to put some conductor as a heatshield
@richardmlea
awesome work
I've seen a couple of threads in the past where people have asked about creating heatsinks for improving the cooling efficiency of their devices. Under normal circumstances a heatsink wouldn't be necessary, but recently with Clemsyn and other kernel devs starting to push the physical limits of the Tegra 3, heat dissipation becomes a major concern at 1.8Ghz and higher. I'm starting to wonder if there might be a way to get creative with some copper foil and a few old laptop heatsinks I've got lying around, just to give the chips a bit of relief from all of the mean and terrible things I do to them. But having never taken my Nexus apart, I have no idea what kind of room is available for heat pipes or foil.
Anybody ever tried making a heatsink for a tablet or phone? This isn't meant to be wholly a serious discussion, and I fully expect to get a lot of flack about battery usage and melting plastic. I just think it would be cool to mod the device into being able to maintain these ridiculous clock speeds and not have it burn my hands.
using the clemsyn 2ghz kernel in front of the a/c works out well
There's very little empty space inside the Nexus 7, so there's no chance of adding additional cooling without more major modding.
I've been looking in to exactly this. I find my Tegra 3 gets to 60 C even before overclocking. If you study the teardown photos you can get an idea of how it might work. I turns out the main SoC chip's headspreader is nicely accessible.
The back pops off the Nexus 7 so easily we can easily take a peak.
My first idea would be to put a little thermal paste in each layer on the SoC's heat spreader, this is covered by a copper RF shield/heat spreader on the chip, and another copper layer on the back cover. Just a tiny dab would do, and it will be smooshed out over an area when the cover goes on. Could get a bit messy though.
There's exactly zero room to work with, it's all very tightly packed and a nicely engineered tablet.
But the back cover is so replaceable you could cut in to it.
If I was going to do it myself I would cut through all layers and have a heatsink directly on the tegra's heatspreader with an adhesive thermal pad. Any more than about something like 1-2mm and it would not be flush with the rear cover.
Alternately some perforation in the plastic on the rear around the area may help.
If i can scrounge some replacement parts I might have a crack at doing stuff.
Whoa whoa whoa, 2GHZ?
BRB !!
Mungulz said:
Whoa whoa whoa, 2GHZ?
BRB !!
Click to expand...
Click to collapse
Yeah, for those people who want to fry their Nexus 7s.
I've only OC'd to 1.4 GHz..not so sure I'll go much farther than that.
Edit: This is just a fun project. Every octa core phone throttles. That includes my S6. Its AnTuTu score from 5 back to back runs with similar 32C start ranges from 65K to 52K. That means a similar drop in performance. Also overheating & throttling are two very different things. Z3+ & S6 both throttle so that they don't get too hot (or 'overheat'). Glass backs on both don't help either, but I like them anyway. I was just trying to speed up the cooling process- not to cool down anything as the phone doesn't 'overheat' in the first place. You won't notice this throttling with regular usage & all these temperature numbers are for internal temp, not surface temp. I hope this clears up my intent. *End of Edit* 07/21/2015
This is probably the easiest way to decrease throttling during heavy CPU workload. All I had to do is insert few foil layers between the phone & TPU case. Attached picture shows plots from three scenarios - no case, just case, foil & case respectively. Oh, NFC will get blocked out by the foil. But I don't use it much anyway. Cheers.
#Reserved#
Very interesting thread, mate! It made my lazy as* to sign up just to post my results. Oh, I used this copper foil with a case. You won't need that much, btw lol
amazon dot com/Louis-Crafts-Copper-Foil-Inches/dp/B0042SWM98
My scores (normalized like yours) from 5 consecutive AnTuTu runs (& my initial temp was also a bit higher than yours)
Initial Temp (C) Score
0 34 100%
1 48.1 91.10%
2 49.1 86.86%
3 49.8 84.80%
4 50.1 83.00%
4K Test:
Outdoor-> 4 minutes in 96F / 35.5 degree Celsius weather (starting CPU temp was 37C as I was using few apps before the recording started )
Walked back home two minutes later and then
Indoor -> 9.5 minutes (CPU was still warm at 41C)
It really is the easiest fix ever for extreme users who use case anyway. Thanks!
nfs2010 said:
Oh, I used this copper foil with a case. You won't need that much, btw lol
Click to expand...
Click to collapse
That's freakin' awesome, dude :good: I never knew copper foil existed. Since I can't afford diamond foil, I'll go with copper I'll take the whole roll though as people are (primarily) using it for shielding their guitar pickups. Thanks a lot for your tip.
Have you guys considered the fact that the phone might, and let me say it again, MIGHT get hotter because we're in summer and it's seriously hot outside? I just checked the forecast for Austin TX, OP's town according to his info, and he has 37C over there. I think that MIIIIIIIIIIIIIIGHT have something to do with the phone getting hotter than usual.
Just saying.
schecter7 said:
This is probably the easiest way to decrease throttling during heavy CPU workload. All I had to do is insert few foil layers between the phone & TPU case. Attached picture shows plots from three scenarios - no case, just case, foil & case respectively. Oh, NFC will get blocked out by the foil. But I don't use it much anyway. Cheers.
Click to expand...
Click to collapse
What do you think about putting foil around the actual battery? Some people have suggested putting paper around it. Does anyone think either of those things are safe?
MarkMRL said:
Have you guys considered the fact that the phone might, and let me say it again, MIGHT get hotter because we're in summer and it's seriously hot outside? I just checked the forecast for Austin TX, OP's town according to his info, and he has 37C over there. I think that MIIIIIIIIIIIIIIGHT have something to do with the phone getting hotter than usual.
Just saying.
Click to expand...
Click to collapse
Yes, it's quite hot over here in ATX. I added an extra comment to my first post. I hope that makes things clear now.
pacattack81 said:
What do you think about putting foil around the actual battery? Some people have suggested putting paper around it. Does anyone think either of those things are safe?
Click to expand...
Click to collapse
The foil will short out the internal components and your phone may get toasted . Please DO NOT try it. But I really wanted to open the back and put some thermal compound like this one. I'll try it some day!
schecter7 said:
Yes, it's quite hot over here in ATX. I added an extra comment to my first post. I hope that makes things clear now.
The foil will short out the internal components and your phone may get toasted . Please DO NOT try it. But I really wanted to open the back and put some thermal compound like. I'll try it some day!
Click to expand...
Click to collapse
Thanks I was very close to trying it out. Funny you should mention the thermal compound...there's a guy on YouTube who opened up the nexus 5 and put some on the CPU and a little piece of metal
heat sink. I have the thermal compound but I don't have the piece of heatsink to test it out so I haven't tried it. One day I'm going to try it though as I have a nexus 5.
pacattack81 said:
Thanks I was very close to trying it out. Funny you should mention the thermal compound...there's a guy on YouTube who opened up the nexus 5 and put some on the CPU and a little piece of metal
heat sink. I have the thermal compound but I don't have the piece of heatsink to test it out so I haven't tried it. One day I'm going to try it though as I have a nexus 5.
Click to expand...
Click to collapse
That's great! You'll have better luck with the compound on the N5 as it has plastic back - I guess? On Z3+, I'll probably get bottle-necked by the glass back regardless of the internal enhancement. I could be wrong though if the heat sink goes all the way to metal side frame. It's certainly worth a shot.
As battery wrap, you'd probably want something that's thermally conductive AND electrically non-conductive.
schecter7 said:
That's great! You'll have better luck with the compound on the N5 as it has plastic back - I guess? On Z3+, I'll probably get bottle-necked by the glass back regardless of the internal enhancement. I could be wrong though if the heat sink goes all the way to metal side frame. It's certainly worth a shot.
As battery wrap, you'd probably want something that's thermally conductive AND electrically non-conductive.
Click to expand...
Click to collapse
Yea, there's got to be something you can wrap around a smartphone battery that could shield in the heat. I just bought an oppo find 7a and it has a removable back. Maybe some sort of insulation can be put on the inside back cover so your hands don't feel the heat when the phone heats up. Any ideas for either the battery and/or back cover? What's thermally conductive, but not electrically conductive?
---------- Post added at 09:28 PM ---------- Previous post was at 09:08 PM ----------
pacattack81 said:
Yea, there's got to be something you can wrap around a smartphone battery that could shield in the heat. I just bought an oppo find 7a and it has a removable back. Maybe some sort of insulation can be put on the inside back cover so your hands don't feel the heat when the phone heats up. Any ideas for either the battery and/or back cover? What's thermally conductive, but not electrically conductive?
Click to expand...
Click to collapse
I can't post links yet, but what about putting some cotton insulation inside the back case? I would think that might shield us from holding a hot phone. Also, what about reflective insulation tape? I think that might actually work. Thoughts?
pacattack81 said:
Yea, there's got to be something you can wrap around a smartphone battery that could shield in the heat. I just bought an oppo find 7a and it has a removable back. Maybe some sort of insulation can be put on the inside back cover so your hands don't feel the heat when the phone heats up. Any ideas for either the battery and/or back cover? What's thermally conductive, but not electrically conductive?
---------- Post added at 09:28 PM ---------- Previous post was at 09:08 PM ----------
I can't post links yet, but what about putting some cotton insulation inside the back case? I would think that might shield us from holding a hot phone. Also, what about reflective insulation tape? I think that might actually work. Thoughts?
Click to expand...
Click to collapse
Wait, we're not on the same page. I was trying to avoid throttling (not shielding the heat). Z3+ back side heats up where the CPU seats (very small spot somewhere underneath the top row of icons). The idea was to take that heat and spread it laterally over a bigger surface area to speed up the cooling process. Without the foil, I still don't feel the heat as my fingers don't touch that hot spot. The foil also indirectly reduces the hot feel from that tiny spot as the heat gets spread more uniformly.
But your case sounds different. You want to avoid the heat from the battery (or the CPU) ? Battery already has a pretty big surface area. And you probably don't want to keep the heat inside by using thermal insulators as that can be very harmful for the battery. You probably want to establish an even faster heat transfer to the environment so that equilibrium point can be maintained at a lower surface temperature. Is that right? A metal back cover can help in that case.
Also here are some electrical insulators that are thermally conductive - but I'm not quite sure about the availability of those
https://www.physicsforums.com/threa...ductive-thermally-conductive-material.125368/
schecter7 said:
Wait, we're not on the same page. I was trying to avoid throttling (not shielding the heat). Z3+ back side heats up where the CPU seats (very small spot somewhere underneath the top row of icons). The idea was to take that heat and spread it laterally over a bigger surface area to speed up the cooling process. Without the foil, I still don't feel the heat as my fingers don't touch that hot spot. The foil also indirectly reduces the hot feel from that tiny spot as the heat gets spread more uniformly.
But your case sounds different. You want to avoid the heat from the battery (or the CPU) ? Battery already has a pretty big surface area. And you probably don't want to keep the heat inside by using thermal insulators as that can be very harmful for the battery. You probably want to establish an even faster heat transfer to the environment so that equilibrium point can be maintained at a lower surface temperature. Is that right? A metal back cover can help in that case.
Also here are some electrical insulators that are thermally conductive - but I'm not quite sure about the availability of those :confused
Click to expand...
Click to collapse
I've tried TPU cases, but I still feel the heat. Maybe a metal case would be better. These look interesting.
amazon(dot)com/gp/aw/d/B00HNKD6A6/ref=pd_aw_sbs_107_1?refRID=1VRK3Q399HJZXA2GHWCJ
amazon(dot)com/gp/aw/d/B00L71LNS4/ref=pd_aw_sbs_107_1?refRID=1BQ362P6XMYRJET82TFG
pacattack81 said:
I've tried TPU cases, but I still feel the heat. Maybe a metal case would be better. These look interesting.
amazon(dot)com/gp/aw/d/B00HNKD6A6/ref=pd_aw_sbs_107_1?refRID=1VRK3Q399HJZXA2GHWCJ
amazon(dot)com/gp/aw/d/B00L71LNS4/ref=pd_aw_sbs_107_1?refRID=1BQ362P6XMYRJET82TFG
Click to expand...
Click to collapse
Interesting! So why does your battery heat up in the first place? Did you try to compare your battery temp (using CPU Z, etc) to others'? I thought battery only heats up during charging.
schecter7 said:
Edit: This is just a fun project. Every octa core phone throttles.
Click to expand...
Click to collapse
That was genius--thank you.
I've attached a heatsink with thermal paste (cheap one) to my nexus 4 once it didn't make a difference
too bad i sold it i can't try it with my Peltier (TEC)
and my note 4 here is cooler without my tough armor (ofc it is, that case is a monster) i think i bent my phone while taking it out will try it with foil as soon as i get one, hope it doesn't damage it :S
a copper plate would be better! or simply a thin heatsink
I tried this maybe a year ago, phone was a lot cooler but I lost my reception. I noticed this after few days, everyone thought something had happend because they couldn't reach me. I was busy gaming ?
Because the phone is opened from the back (http://www.witrigs.com/blog/sony-xperia-z4-teardown/) we should crowdfund a metal replacement made of aluminium but in the same glossy style and color the frame is and with a copper base which directly connects to the thermonuclear fusion core (aka Qualcomm) so that the heat is as best as possible transported from these to the whole backplate. The only difficulty will be the holes for the camera and LED light to be waterproof. And while we are at it, we could make the backplate a little bit ticker than the glass currently is so that the tiny height difference between the glass and the frame is gone too.
Ok, we can argue about the color and thickness but you get the idea. Should we do that? Once we got them funded we can sell them and get rich
an3k said:
Because the phone is opened from the back (http://www.witrigs.com/blog/sony-xperia-z4-teardown/) we should crowdfund a metal replacement made of aluminium but in the same glossy style and color the frame is and with a copper base which directly connects to the thermonuclear fusion core (aka Qualcomm) so that the heat is as best as possible transported from these to the whole backplate. The only difficulty will be the holes for the camera and LED light to be waterproof. And while we are at it, we could make the backplate a little bit ticker than the glass currently is so that the tiny height difference between the glass and the frame is gone too.
Ok, we can argue about the color and thickness but you get the idea. Should we do that? Once we got them funded we can sell them and get rich
Click to expand...
Click to collapse
That'd be excellent & throttling would probably be gone forever. I'm in But some dudes might mix up fast heat dissipation with 'overheating & throttling & battery drain' - all in one sentence The rear area that gets warm on Z3+ is actually very narrow & my fingers don't touch that part at all. But we've already seen a ridiculous amount of whining over that. Can you imagine the whining as we try to expand that dissipation area to get rid of throttling?
I think the thickness would be debatable as some may want to keep the slightly raised lips on the back to keep their phones from sliding around.
fredrik8 said:
I tried this maybe a year ago, phone was a lot cooler but I lost my reception. I noticed this after few days, everyone thought something had happend because they couldn't reach me. I was busy gaming
Click to expand...
Click to collapse
lol - good point. It depends on the antenna placement - I think. I didn't experience any difference in reception. I usually get 0-1 bar at home. So I really didn't have anything to lose in the first place lol
If you do this and have the phone on max brightness, does it auto-dim when loading xda's website?
Due to all the ads and issues with the website it always causes the screens brightness to throttle when loading, and then go back to full brightness afterwards.
(Try loading a couple of different topics when doing this)
I decided to run Cpu Throttling Test to measure how is the stock thermal performance of the phone and I noticed that it is rather lackluster. After about a minute and half of full cpu load(100 threads option in the program) the processor starts jumping around 800mhz and 1.2ghz, if the load is for a longer amount of time it would likely throttle down to 800mhz completely and keep in mind that this is with only the heat of the cpu, if you are doing something else that is stressing the gpu and storage as well it would throttle harder. Nowadays as you know galaxy s2 is often running on full load due to modern operation systems and apps being pretty heavy.
I had a look at pictures of the motherboard of the phone and instantly noticed a significant design flaw which is what causes the throttling-there is no heatsink over the soc at all. On the pic attached you can see the soc with another fairly big chip next to it(probably the baseband, idk).
I had some copper heatsinks left from a previous project so I decided to try adding them on top of the naked chips with some thermal paste. The size of the copper plates is 15x15mm, thickness 0.3mm.
So I disassembled the phone, removed the circle sticker from the soc, cleaned it and the chip next to it with some isopropyl alcohol then applied a tiny amount of thermal paste to the chips with a plastic spudger. Just a very thin coat. The next step is cleaning the copper heatsinks with isopropyl alcohol and sticking them on top of the chips. You only need to apply thermal paste to the chips, don't bother applying it to the copper heatsinks as well as if you put too much thermal paste and stick the chips it will likely cause a mess and get on the resistors and other components.
After that I applied a small amount of thermal paste to the plastic mid frame where chips would usually fit. Before that I cleaned the spot with a little isopropyl alcohol. I used a picture from ifixit teardown and drew with blue color on the spots where you should put the paste.
Well that is the mod. Now reassemble the phone.
Please keep track of the two little black screws that are securing the mainboard in place and be cautious around your volume and power button flex cables, as they are usually glued with weak adhesive to the plastic frame, so if you pull out the mainboard without wiggling them out of the adhesive first you might accidentaly rip them out or damage them.
And now, for the results. As last time, I did a full cpu load stress test with 100 threads. This time I waited the full 15 minutes and behold, the cpu didn't drop below 1.2ghz at all! This is insane improvement in thermal performance. The program says that the cpu thottled to 91% of the max performance, however that reading is due to the small inconsistency of the ''GIPS'' performance which is due to the difficulty of the load, rather than actual thermal throttling. As for the soc temperature, my rom doesn't seem to read it, I only get the battery temperature which was 35C after the 15 minute stress test. The 50C reading from the program is also wrong, it probably just lists it like that because it can't find a temperature reading for the cpu.
In reality even on stock speeds I feel that the phone runs smoother now. However, there is definitely plenty of room for overclocking now, easily to 1.4-1.6ghz. Unfortunately I'm using @rINanDO 's lineage os 14.1 with emulated storage(android 7.1.2) and there is no kernel with cpu overclock for that version, so I can't test that myself. Although I believe such a kernel will be very useful because this android version runs faster than android 9+ while still supporting nearly all apps.
So to sum it up, the benefits of this mod:
-thermal thottling completely removed
-lower temperatures mean less stress on the silicon and longer device lifespan, which is important as this model is already 11 years old
-plenty of thermal headroom for overclocking and significantly increased performance even on stock speeds
And the requirements for the mod:
-a screwdriver
-thermal paste, preferably non conductive
-two 15x15mm 0.3mm thickness copper heatsinks-I got mine from Aliexpress, a pack of 10 costed me 1.25$. They also come with a generic thermal grease but I don't recommend using it. I guess it will do the job if you don't have any other thermal paste.
-some isopropyl alcohol is also recommended for cleaning the surfaces, for better contact
-maybe a disassembly tutorial, anyway disassembling this phone is fairly easy. If you have no experience take your time
Unfortunately I didn't take pictures while doing the mod, so I hope the generic ifixit disassembly photos and my explanation are enough. The mod is pretty easy and took me around 30 minutes.
Informative
Tried it with alluminium instead (i cut 2 pieces from a pc cooler) and in android 12 it did throttle after 5 and a half min, but i undervolted it to 1175mv at 1200mhz and now it is throttling after 8min 45 sec, used arctic mx2 thermal paste. I didn t tested it before the mod, but i will try some games to see if alluminium really makes a difference. After the phone cools down i will try at 1300mhz, thx for the tutorial.