Hi guys,
Wondering if anyone has the Pin out schematics for the glasses. So far I have found out that the connector is a JAE dd2 connector 40 pins. If anyone can help me out that would be great. I heard Colorado audio video made some kind of adaptor for the unit.
Trying to get my electrical engineering friend to make me and adaptor to us the glasses on a newer phone or device
Thanks
Related
This is probably a fairly simple problem for you guys.
The connector on the bottom of my XDA2 appears to have come dislodged.
It has been getting harder and harder to get it to charge recently but with a bit of pressure in one direction it appeared to charge OK.
That is until my GF plugged it in to charge and now its totaly dislodged.
I think the socket has broken free from its soldered terminals into the PCB inside the XDA2.
Is there a quick fix anyone can suggest (I am a qualified Electronic Engineer and can solder) or is there a repair centre (hopefully near Newcastle upon tyne (North East UK).
PLEASE someone HELP!!!!
Tom
i have the same problem, but i got the pin chart from here, and wired a charge hole on the outside. now i can only sync via IR. lot slower that usb. for some reason, the solder wont hold the same plug the way the manufacter did.
good luck.
Xda Service Centre
Vulcan Road North
Norwich
NR6 6AQ
Tel: 0808 100 3427
Pin Diagram for XDA 2 Connector
Where on here can I get pin connector.
Also where can I get tool to unscrew back off XDA2 so I can try and repair myself
Tom
1) use the search function. it's on wiki.xda-developers.com
2) you seem pretty unsure of yourself for a EE qualified engineer. Why, where does one obtain a torx screwdriver? A T6 will do.
We get this alot at work and use these guys. email them on
[email protected]
35 quid for a fix 72hr turnaround.
And no i have nothing to do with them
Possible solution
Hello,
I have the same problem and have managed the following solution to be able to charge the device with "a connector", its working perfect for me:
Note: You will lost some headset-functionality, I have tested that no internal components are affected, because the PIN used for power supply is cutted from the mainboard.
Disasemble the Device completely to have the main circuit board in the hand free from other coponents to be able to solder properly.
Buy a 4-contacts mini-jack connector (2.5mm)
Cut the Power Supply cable Power-Jack to replace it with the Mini-Jack (Image2 and Image4 )
Solder a cable to the 3 last ping of the base connector (Image1)
Cut (with Dremel for example...) one of the connectors of the Jack soldered on the mainboard (Image 3 and Image5)
Solder the cable that comes from the Base connector to the onboard Jack (Image 3 and 5) This is to get positive power from the Jack connector to the right place on the mainboard.
I hope this is enough, if you need more details please let me know.
Regards,
I have the same problem, though I am able to charge my qtek 2020 by putting it in one direction.
I am thinking about soldering a femal mini-usb port using pins 13,20,21,22 for positive power, 16,17,18 for ground, and 14,15 for UDC+ and UDC-. Has anyone managed to do this ?
Aw crap. Same thing's just happened to my XDA. The connector at the base has snapped. It's still connected (barely) but charging and data transfer won't work.
Is there any way to replace the connector with a mini-usb port at all or an alternative method that doesn't require me to send my phone out for 3 days?
Some threads that might help:
How to install USB connector
http://forum.xda-developers.com/showthread.php?t=242772&highlight=connector
pinout from wiki
http://wiki.xda-developers.com/index.php?pagename=Connectors
Please help me out to find pinout for standard USB sync cable. I have Windows PH10B phone and I bought Qtec 2020 sync cable on ebay and unfortunately it doesn't charge and doesn't sync.
Thank you,
Eugene
Hi
I'm looking for USB in extension port or somewhere else on the mainboard becouse it's been dameged under the sync/charge port and I need to rewire USB from somewhere else. Also does anybody know why joystick don't work ? mechanicly it's perfect so I have no idea.
Anyone? Please help...
Hallo, I have the same Problem. I have only few soldering pads of connector after the connector is cracked out. But if you kann see, evtl. under microscope, there are little holes, which connects to the pads, if the pads are OK. I measured some pads and found the following points . See pictures..
I has not tested the functionality yet! because i have no connector yet -->Caution! If you or somebody could still check the Pins again, would be great! Because I have no second Board and I cannot be sure with 100%.
Hey ppl
I've just broke my bottom connector for the second time - by using a car plug. This connector is so weak...
I thought of resoldering it with a miniUSB connector, has anyone tried it? It would be better IMHO.
http://forum.xda-developers.com/showthread.php?t=242772&highlight=connector
wallaby and himalaya share connector as i'm using my wallaby cradle
so guess if you wire it to a miniusb it would work just fine too
Thanks, good man
I've also found this article in Wiki
OK, as for now I have resoldered my connector (again...). But - one pin is lost. D+. So, I can charge it, but not synchronize
So, I have to either find a new connector, or mount this miniUSB connector.
I just bought the HTC 3-in-1 adaptor from ShopBrando HK. I am using it in the car with the Brodit holder to have both charger and 3.5 mm for the car stereo aux input. I am modifying the holder (removing the charger pin for the adaptor 11 pin).
The problem is that the adaptor's wire is too short. I want to hide the adaptor somewhere in the car and a longer wire is needed.
I am thinkng about
a) Use and extension wire ( if there is any) Is there an extension cable (male to female -11 pin usb) ???
b) Cut and extend the lenght of the wire.
What is the wire used?? If I cut the wire to extent it, what kind of wire should i ask for?
Thank you
This is exactly the same problem I am facing. Can't find a ExtUSB Male to Female extension. But I would be up for trying to extend the cable if I could buy some. Hopefully someone will answer.
foaf said:
This is exactly the same problem I am facing. Can't find a ExtUSB Male to Female extension. But I would be up for trying to extend the cable if I could buy some. Hopefully someone will answer.
Click to expand...
Click to collapse
I'm in the same boat, Its not easy finding one so if anyone can help then please do
Another post highlights the same problem but these guys found one, I have tried the google search mentioned but still no good.
Nogs
Yeah. I cant find the extender they are refering to on Google either.
im in indonesia, where i can buy it?
i cant found it in my country.
someone can help me?
tnx.
chris2004 said:
If I cut the wire to extent it, what kind of wire should i ask for?
Click to expand...
Click to collapse
Just clip off 1/2 inch and take the sample with you to the store to show the sales people. At the same time, you should get the proper connecters to splice the wires together.
Does anyone really need to extend all 11 pins for both audio and power, or just power, or just audio?
Hello everyone,
I want to install the tablet on my car's dash but it barely fits.
I managed to open the back case of the tablet and exposed the connectors. I could solder some wires to extend the connectors but I ran into trouble in figuring out the pinouts.
It has a some side pins that go from the microusb port but I'm not sure if I should connect 5V there.
Also the audio jack has 5 pins which I don't quite understand what they do.
Any sort of advice or information will be appreciated
Thank you,
Adrian