Database Users

[Q] broken screen - rescuing data

Hello,
my Nexus 4 dropped on the floor and now the touchscreen in the bottom right corner is not working anymore. This is a very unfortunate position since I am not able to press the "OK" button to unlock the lockscreen. I now want to at least save my data. USB Debugging is not enabled, so adb commands are not working :/
I googled a bit and found this thread witch the pretty much same situation:
http://forum.xda-developers.com/nexus-4/help/nexus-4-to-copy-data-broken-touch-input-t2415195
The steps to take are described as the following:
Read this guide http://forum.xda-developers.com/show....php?t=2266654 . only follow the parts to unlock the boot loader and flash clockworkmod custom recovery. Make sure that you flash the recovery right after unlocking (without rebooting in between) otherwise data will get wiped. )
After that boot into your newly flashed recovery and use "adb pull /data/media/" . this should copy everything on the internal sdcard of the phone.
Click to expand...
Click to collapse
So i did unlock the bootloader and flashed a clockwork custom recovery (6.0.4.7). I also managed to not reboot the phone between these two steps.
I was not sure what to do now as i did not know what was meant by boot into your newly flashed recovery . So i found another thread and followed these instructions
http://forum.xda-developers.com/showpost.php?p=41291371&postcount=28
After wiping the cache in step 4 i was in a boot loop (at least it took time like an eternity) and shut down the phone manually (by pressing the Power On button a few seconds). The new bootet phone is now in a state where I have to set the language for the new clockwork custom recovery. I tried to do some adb commands (because USB Debugging should not be the problem anymore) but it did not work. I am also scared that because of my manually shutting down caused a full wipe as i read the following sentence in the latest thread:
This no longer seems to be working if your phone is on official 4.3 (meaning you have the 4.3 bootloader). It will only give you a bootloop and then you will end up having to do a full wipe, resulting in losing your data. Only do this is you are on 4.2.
Click to expand...
Click to collapse
My question is now: Is all my data lost now? And if not, how can I save it / where did I go wrong?
Thank you for your help, I appreciate it!
frucade

Unlocking the bootloader wipes your device. So, yea, your data is gone. Without a custom recovery and a locked bootloader you were doomed from the beginning.
Sent from my Nexus 9 using XDA Free mobile app

Bootloop With locked bootloader 7.0

My 6p is stuck in a bootloop. nbd90x build my bootloader is locked is there anyway to unlock from adb. I have already tried sideloading ndb90x through adb wipping chache and user data and still no luck. Help me Xda youre my only hope..

So you previously enabled USB debugging, how about OEM unlocking? If so, use 'fastboot flashing unlock' to unlock the bootloader. Note that internal storage will be completely wiped. Everything. Though with USB debugging enabled, you should be able to adb pull the contents of you SD card first. If you can unlock the bootloader you can try flashing factory images with fastboot. Otherwise, not much else besides RMA it with Google. There's been a few reports of stock N6Ps bootlooping. Haven't seen anyone post that Google denied the claim.

no bootloader is locked so cant flash using flashboot but debugging is enabled so I am able to use adb .

I know. What I'm asking is if you enabled allow OEM unlocking in developer settings? That doesn't unlock your bootloader in itself. You still need to use fastboot to do it. However if that setting IS enabled what you can do is... Use ADB to pull your internal storage to PC. Then use fastboot to unlock the bootloader and flash factory images. If the setting is not enabled, and wiping data and flashing an OTA don't work, I'm not sure what else can be done.
You can try downloading the 7.1 dev preview OTA and seeing if it updates whatever is causing it to fail. Other than those, RMA would be your best bet.
https://developer.android.com/preview/download.html#device-preview

After sideloading a ton of times between 7.0 and 7.1, one time i got it to boot up then i immediately enabled oem unlock then it crashed again... so now I am able to flash through fastboot although I havent been able to get it to boot again. Is it normal for bootloops to not get fixed by flashing?

Hijacking your post to report what is happening to me. I posted the same thing on the Android Beta program community on G+.
Have been using the latest beta since it came out on completely stock 6P (locked bootloader, unrooted). Everything working normally when yesterday around 10 or 11AM, phone starts to bootloop OUT OF NOWHERE, it was just sitting there on the table while I was working. I could still get to bootloader/recovery, so that was a bit of a relief. First thing I tried: clear cache, nothing. Then proceed to wipe/factory reset the device, to no avail. Immediately downloaded the latest factory image from Google's page, tried flashing it but couldn't since the bootloader was locked (OEM unlock option also disabled). Then downloaded the beta OTA and sideloaded it, process went through OK but device still bootloops. Tried sideloading the latest stable OTA but didn't work since it was from a previous build. Ran out of ideas. So there I was creating a thread on XDA for help while the device was still on its bootloop rush, about to hit the Submit button when again OUT OF THE BLUE SKY the device decides to boot itself back up. First thing I did was unlock the bootloader. Phone worked normally for 6 or 7 hours, when I'm doing something on it and then again, screen froze and bootloop starts again. This time I only reset the device and left the it bootlooping, after about 30 minutes it boots up again. I unenrolled from the beta and installed the latest 7.0 build. Everything working fine for the last 12 hours. Anyone have any idea on what can cause the device to bootloop like that? Never seen anything like it.

Yea I signed up for the beta program too do you have the link to unenroll? So you just reset and let it sit?

Here you go
google.com/android/beta

do you remember what you did to get it to boot?

noetre said:
do you remember what you did to get it to boot?
Click to expand...
Click to collapse
Well, that's the thing. Everything I tried didn't seem to work. I couldn't flash the factory image since the bootloader was locked. I was able to sideload the beta OTA but the device still bootlooped after that. So I just left it bootlooping and after around 20 or 30 minutes the device booted normally. I have no idea what caused it and what I did to make it work again.
P.S: device restarted 2 times while I was typing this.

noetre said:
do you remember what you did to get it to boot?
Click to expand...
Click to collapse
If your boot loader is locked you are screwed, sorry to say, I would RMA it. Unbelievable an update can mess a phone up...that's why I always unlock the bootloader first thing and never lock it. I need complete control of my phone.
Edit: Only thing I can think of is delete the partitions with fastboot or adb and reflash factory image.

boot loader is unlocked now Ive tried flashing using the flash-all script but the phone still wont boot

noetre said:
boot loader is unlocked now Ive tried flashing using the flash-all script but the phone still wont boot
Click to expand...
Click to collapse
As a last resort, flash all of the images manually with fastboot. This will wipe all userdata and completely format the SDcard. Nothing will be left. Extract the bootloader and radio images from the factory images zip. Flash them in fastboot. Reboot to fastboot again. Extract the next zip in the same folder as BL & radio images and flash the vendor, system, boot, recovery & userdata image files. Just for good measure, boot to recovery (stock Android recovery) and perform a factory reset & cache wipe. If the phone still fails to boot, your only option would be to RMA it at this point.
Note: As per Heisenberg's sticky thread, do NOT flash userdata.img if you have anything besides the 32gb model as you will only have the ~32gb storage available. If you're using a model with more storage, just use fastboot to format userdata but don't flash the image.

Ill try that.. but isnt the warranty voided because the bootloader is unlocked?

noetre said:
Ill try that.. but isnt the warranty voided because the bootloader is unlocked?
Click to expand...
Click to collapse
Not on a Nexus, no.
Added: I had to RMA mine after the phone got its first update. I unlocked the bootloader and stayed stock for a long time (until N came out). I took the OTA in About Phone and it applied with no problems but the phone would not boot. Factory images also couldn't get it running. Stock recovery and all. RMA'd without issues. I didn't tell them, just sent it in. If they tried to boot it they would've seen the unlock symbol. There's also a thread somewhere buried in the general section where someone called Google and asked and they confirmed to them that unlocking does not void warranty. I'll try to find it for you.
Found it: http://forum.xda-developers.com/nexus-6p/general/unlocking-bootloader-warranty-google-t3229804/page1
I also returned 4 faulty Nexus 5's (mostly screen artifacts) all unlocked with no problems.

How to Stock FW and Relock Bootloader? OP5

Hi all,
I've wanted to go back to Stock OS but when i type "fastboot oem lock" it says "FAILED <remote: Flashing Lock is not allowed."
Everything boots normally to OS 4.5.2. In DEV options the Unlock Bootloader is greyed out and says bootloader is already unlocked.
What can i do?
Cheers

These instructions did work for me with the OnePlus 3/3T. They should also work for the OnePlus5, just make sure that you download the OnePlus5 version of the software and recovery.
https://forums.oneplus.net/threads/...-3-3t-and-go-back-completely-to-stock.456232/
Use this link for the stock recovery: https://forum.xda-developers.com/showpost.php?p=72748921&postcount=5

reayard said:
These instructions did work for me with the OnePlus 3/3T. They should also work for the OnePlus5, just make sure that you download the OnePlus5 version of the software and recovery.
https://forums.oneplus.net/threads/...-3-3t-and-go-back-completely-to-stock.456232/
Use this link for the stock recovery: https://forum.xda-developers.com/showpost.php?p=72748921&postcount=5
Click to expand...
Click to collapse
Hi i tried but does the same when i get to fastboot oem lock (it says Flashing Lock is not allowed).

r1card0amr said:
Hi i tried but does the same when i get to fastboot oem lock (it says Flashing Lock is not allowed).
Click to expand...
Click to collapse
Thanks I asked the same question earlier glad u tried it..I want to make sure we can relock it before I get the phone. Did u enable oem unlocking in the developer options before doing a fastboot oem lock? Also, make sure you are on stock everything including recovery..

mohan_kr said:
Thanks I asked the same question earlier glad u tried it..I want to make sure we can relock it before I get the phone. Did u enable oem unlocking in the developer options before doing a fastboot oem lock? Also, make sure you are on stock everything including recovery..
Click to expand...
Click to collapse
Hello. I first thing I do always is to install drivers. I start by connecting the phone to the laptop in charge mode, then in transfer files mode, MTP or camera. In this way he will recognise all the drivers your laptop needs.
Also I enter in fastboot mode and recovery so the laptop can recognise the drivers and always reboot laptop and phone just to double check.
What I did was: go to Developer Options and enabled Unlock Bootloader and USB Debugging.
Then I accepted the laptop request on my phone and all drives were OK.
I run CMD and typed fastboot devices to see if it recognises my phone and it displayed a serial number. So I proceed next to type fastboot oem unlock and the process went OK and on my phone it asked Yes or No to unlock and I choose yes.
Then I flash a twrp image by typing on CMD: fastboot flash recovery recovery.img (my twrp I'm had other name so I rename it. You need to enable "Show file extensions" in Windows so you can see what the extension is).
I then type fastboot boot recovery.img and the phone entered in Recovery Mode in this case TWRP.
My phone was always connected to the laptop and he open the internal storage window so I drag the supersu inside.
Then on TWRP I wiped dalvik and cache and I went to Install and installed the SupeSU on my internal memory root.
The phone then rebooted and ready to go.
But then I went to developer options and the Unlock bootloader was greyed out. I unroot my phone and flashed a stock recovery for OP5 and the stock image 4.5.2 and when I type fastboot oem lock it always says it can't be flashed.
I need to stock it since I'm giving to a family member and they don't understand much about phones and If there's a problem the warranty doesn't cover.
Just installed supersu to try an app. I never install 3rd party roms.

r1card0amr said:
I need to stock it since I'm giving to a family member and they don't understand much about phones and If there's a problem the warranty doesn't cover.
Click to expand...
Click to collapse
the warranty is not voided with unlocked bootloader..
https://oneplus.net/hk/support/answer/will-rooting-or-unlocking-the-bootloader-void-my-warranty

I found now that if i take pictures or screenshots the Album Folder is empty. I think my phone is bricked. Hence i can't lock the bootloader.

r1card0amr said:
I found now that if i take pictures or screenshots the Album Folder is empty. I think my phone is bricked. Hence i can't lock the bootloader.
Click to expand...
Click to collapse
if your phones boots its not bricked... My guess is that you data is corrupted, i would wipe everything including userdata en reflashing the stock with recovery.

Hogyoku said:
if your phones boots its not bricked... My guess is that you data is corrupted, i would wipe everything including userdata en reflashing the stock with recovery.
Click to expand...
Click to collapse
Hi right before your comment i managed lol.
I re-flash the stock recovery and in recovery i reset and wipe everything. then i install the OS4.5.3 by ADB Sideload and it's working now.
Just wanted to get rid of the inital warning that my bootloader is unlocked. I want to lock again.

I rooted my device with Magisk, and now I want to restore it to factory state.
I flashed stock recovery and OOS several times, wiped everything but fastboot oem lock failed all times (FAILED (remote: Flashing Lock is not allowed)).
Can you help me?
What should I do to relock bootloader?

here is your solution
r1card0amr said:
Hi right before your comment i managed lol.
I re-flash the stock recovery and in recovery i reset and wipe everything. then i install the OS4.5.3 by ADB Sideload and it's working now.
Just wanted to get rid of the inital warning that my bootloader is unlocked. I want to lock again.
Click to expand...
Click to collapse
here in this video u can see in detail how to lock bootloader. hope this help you
https://www.youtube.com/watch?v=CQYCSdDUdAU

HOW TO RELOCK..
Install TWRP and Magisk if you don't have them yet.
Magisk should allow you to slide "OEM unlocking" to "enabled"
Reboot to fastboot
Flash stock recovery via fastboot.
Run locking via fastboot flashing lock
Allow it to reboot and upon start up it will say device corrupted (THIS IS NORMAL)
Boot to recovery via the warning start screen.
Once in recovery, sideload latest FW.
Profit.

I usually do it this way (successfully):
Wipe everything but OTG in TWRP
Format data
Reboot to TWRP
Flash the full stock OOS zip
Reboot to fastboot
Flash stock recovery
Lock bootloader with the fastboot lock command

Has anyone made any progress with this? I too am having the issue as described and have tried the solution by Ricyksydhu, along with solutions from various other places around the net.

Hard/soft brick

I think I messed up my PH-1 something royally.
All I was trying to do is unlock my bootloader and load Magisk.
To preface this, my PH-1 seemed to act a little wonky from the get-go. I bought it 3rd person from a guy on craigslist so anything warranty involved I think I'm out of luck.
The phone would take a while to power on, it took something like 10secs on the power button just to turn it on. And if I set it to reboot , it boots into the bootloader. Also, I was never able to access the recovery (even using power + up). It always felt like I had to hold the buttons for way to long to get to its destination; e.g. up and power to get into fastboot.
Ok where I'm at now. In can occasionally get into fastboot mostly after it bootlooping a few times. It won't get past the Essential logo if I try to boot it up.
PS I was able to unlock the bootloader.
Steps I took to remedy this:
> erase all user data in fastboot
> hold power + u + d to hard power off
> follow this guide https://forum.xda-developers.com/essential-phone/how-to/guide-rooting-essential-ph-1-magisk-t3701976
> attempt to install stock system image via flash-all
>a ton other
Here are the results of that.
https://imgur.com/a/iVwwS
Help me guys please. :crying:
A little progress, I was unable to unlock_critical but its still hanging here
https://imgur.com/a/IdZum

jAm-0 said:
I think I messed up my PH-1 something royally.
All I was trying to do is unlock my bootloader and load Magisk.
To preface this, my PH-1 seemed to act a little wonky from the get-go. I bought it 3rd person from a guy on craigslist so anything warranty involved I think I'm out of luck.
The phone would take a while to power on, it took something like 10secs on the power button just to turn it on. And if I set it to reboot , it boots into the bootloader. Also, I was never able to access the recovery (even using power + up). It always felt like I had to hold the buttons for way to long to get to its destination; e.g. up and power to get into fastboot.
Ok where I'm at now. In can occasionally get into fastboot mostly after it bootlooping a few times. It won't get past the Essential logo if I try to boot it up.
PS I was able to unlock the bootloader.
Steps I took to remedy this:
> erase all user data in fastboot
> hold power + u + d to hard power off
> follow this guide https://forum.xda-developers.com/essential-phone/how-to/guide-rooting-essential-ph-1-magisk-t3701976
> attempt to install stock system image via flash-all
>a ton other
Here are the results of that.
https://imgur.com/a/iVwwS
Help me guys please. :crying:
Click to expand...
Click to collapse
read through this and follow the steps should be good to go.
https://forum.xda-developers.com/essential-phone/development/stock-7-1-1-nmj20d-t3701681
This is also very helpful
https://mata.readthedocs.io/en/latest/

That's the exact process I was going through, and it finally booted up.
The issue I was having was a bad usb connection which wouldn't allow me to unlock_critical.
SOLVED. Still no Magisk, we'll worry about that another time. 5hrs of troubleshooting is enough for one night.

https://imgur.com/a/ZiBzp
SO close to getting Magisk to install, any reason the refuses to flash the boot partition? I used the stock boot.img and had Magisk patch it before I flashed

SO close to getting Magisk to install, any reason the refuses to flash the boot partition? I used the stock boot.img and had Magisk patch it before I flashed

jAm-0 said:
SO close to getting Magisk to install, any reason the refuses to flash the boot partition? I used the stock boot.img and had Magisk patch it before I flashed
Click to expand...
Click to collapse
You have to flash magisk in twrp recovery NOT bootloader mode.
It's right in the OP from the rooting guide you followed:
Do not set up a password if you are on 8.1 twrp doesn't work.
You need to read through that rooting guide and make sure you know what you're doing before you try.
This phone is easy to hard brick and there is no solution to recover from that.
OREO 8.0/8.1
REQUIREMENTS:
An unlocked bootloader.
A working ADB/Fastboot environment on your computer. Knowledge on how ADB and Fastboot works is also preferred.
The stock boot image for whatever build you're running/trying to root.
The latest TWRP build for our device.
If on 8.1, remove your pin/pattern/passcode until the root process is done.
1. Download both the stock boot image for whatever build you're running and the Magisk or SuperSU zip. Transfer both files to your device's internal storage.
2. Reboot your phone into the bootloader, then open up your command prompt or terminal and flash the latest TWRP build for the device using:
Code:
fastboot flash boot twrp.img
3. Once TWRP has finished flashing, reboot into your recovery. When prompted, enter your pattern/passcode/password to decrypt your data in order to gain access to your internal storage.
4. Once you're in TWRP, install the stock boot image and then the Magisk/SuperSU zip.
5. Whenever Magisk/SuperSU finishes installing, simply reboot your device! You should now be rooted.
*NOTE: TWRP will NOT remain installed on your device.

wolfu11 said:
You have to flash magisk in twrp recovery NOT bootloader mode.
It's right in the OP from the rooting guide you followed:
Do not set up a password if you are on 8.1 twrp doesn't work.
You need to read through that rooting guide and make sure you know what you're doing before you try.
This phone is easy to hard brick and there is no solution to recover from that.
OREO 8.0/8.1
REQUIREMENTS:
An unlocked bootloader.
A working ADB/Fastboot environment on your computer. Knowledge on how ADB and Fastboot works is also preferred.
The stock boot image for whatever build you're running/trying to root.
The latest TWRP build for our device.
If on 8.1, remove your pin/pattern/passcode until the root process is done.
1. Download both the stock boot image for whatever build you're running and the Magisk or SuperSU zip. Transfer both files to your device's internal storage.
2. Reboot your phone into the bootloader, then open up your command prompt or terminal and flash the latest TWRP build for the device using:
Code:
fastboot flash boot twrp.img
3. Once TWRP has finished flashing, reboot into your recovery. When prompted, enter your pattern/passcode/password to decrypt your data in order to gain access to your internal storage.
4. Once you're in TWRP, install the stock boot image and then the Magisk/SuperSU zip.
5. Whenever Magisk/SuperSU finishes installing, simply reboot your device! You should now be rooted.
*NOTE: TWRP will NOT remain installed on your device.
Click to expand...
Click to collapse
I realize all that, the issue is I cannot access any sort of recovery because I think my bootloader is defective.
For example from a cold restart if I press the power button for say 3 -5 seconds it wont boot, just boot to the Essential logo and loop. To get the phone to boot I have to hold the power down for 15-20 seconds while it bootloops a couple times then it'll boot.
Is there a possible way to reflash the bootloader software if it is defective? It's unlocked btw
There is a way to install magisk via fastboot with a patched_boot img which I'm working on. Cant seem to find the right boot img to patch for 8.1
PS Is it possible to flash .zips through fastboot? e.g. custom roms etc

Was finally able to get into recovery, so all is well. Thanks for the help yall

OP, what was your process to successfully get into recovery and fix your problems?
It may help others sometime?

gimpy1 said:
OP, what was your process to successfully get into recovery and fix your problems?
It may help others sometime?
Click to expand...
Click to collapse
It's really hard to say, my phone has a serious problem with it. sometimes I cant get it to boot, it will boot into the bootloader over and over and over. I've managed to get Lineage 15.1 on if for a bit until I tried to get back into the recovery which sent it manic.
I just got lucky I was able to get into TWRP and flash lineage.
my first issue not being able to flash the stock image via fastboot because I didn't unlock_critical which can sometimes fail when the usb connection is bad.
Currently flashing stock again if my phone will boot up. I'm not sure whats wrong with my bootloader but its causing a ton of havoc

My essential phone stuck in boot logo,bootloader work but recovery doesn´t work
Bootloader locked.
Oem unlocking disable.
Usb debugging disable.
How to flash stock recovery or twrp on bootloader locked ? please
Thank you!

katastyle971 said:
My essential phone stuck in boot logo,bootloader work but recovery doesn´t work
Bootloader locked.
Oem unlocking disable.
Usb debugging disable.
How to flash stock recovery or twrp on bootloader locked ? please
Thank you!
Click to expand...
Click to collapse
Same boat for me - just keep rebooting to show Powered by Android Screen and then reboot again and again. Was able to see my device using fastboot devices command but all attempts to access recory just repeat the bootloop entry. I would happily check the OEM UNLOCK option in dev settings but can't even get it to book to any OS to make that option happen. Still shows bootloader locked on bootloader screen - any help someone can suggest?

I had this problem tonight also. In my case I suspect it had to do with the install of magisk in which I checked both boxes and patched the bootloader. on reboot I was stuck on boot. Just wanted to add my solution. I got the pie back to stock zip here https://forum.xda-developers.com/essential-phone/development/stock-7-1-1-nmj20d-t3701681 then I put it into the adb folder and ran the flashall.bat script. I tried the no wipe one and it saved my information. very happy I didnt have to resetup my phone in the end.

katastyle971 said:
My essential phone stuck in boot logo,bootloader work but recovery doesn´t work
Bootloader locked.
Oem unlocking disable.
Usb debugging disable.
How to flash stock recovery or twrp on bootloader locked ? please
Thank you!
Click to expand...
Click to collapse
I am in the same boat. I tried to re-install the OS, but because my USB debugging was not enabled, Fastboot worked but ADB would not and since I basically wiped the recovery area, my phone will only boot into Fastboot but will not allow any loading of recovery. I would pay for someone to help. This is so hard to figure out. I have contacted Essential but since my phone is over 12 months old, the warranty has expired.
Help please. It seems like such a waste to have a bricked phone.

Can't lock bootloader because I can't get into fastboot.

Hello, I've recently been stumped. Last night I attempted to install Lineage OS on my Axon 7 A2017U. I used Axon7Toolkit to unlock the bootloader and install TWRP. This was the first I've seen of the warning from google telling me to lock my bootloader. (My Motorola Nexus 6 never did this) So I ignored it until I had Lineage installed and when I tried to boot, the system was encrypted with a password. The internet said there is no password. I just have to wipe in TWRP. So I tried that to no avail. At that point I said screw this. I'm gonna go back to stock before I mess anything up. Flashed stock using MiFlash. Everything is good and dandy except that aforementioned warning message when booting. No matter what I try, I can't get into fastboot to lock the bootloader. Every time I try, it shows that message and boots normally. I've tried using "adb reboot bootloader" it went to the message and boots to OS. I tried holding power and volume up then selecting bootloader. Same result. I tried holding power and volume up then selecting recovery (this is when I realized TWRP was gone. It must have been overwritten when flashing stock firmware) and then reboot to bootloader. Same result. I really don't know what else to try. I guess I could ignore it, but that's really not what I'm looking for.

ScottDemon said:
Hello, I've recently been stumped. Last night I attempted to install Lineage OS on my Axon 7 A2017U. I used Axon7Toolkit to unlock the bootloader and install TWRP. This was the first I've seen of the warning from google telling me to lock my bootloader. (My Motorola Nexus 6 never did this) So I ignored it until I had Lineage installed and when I tried to boot, the system was encrypted with a password. The internet said there is no password. I just have to wipe in TWRP. So I tried that to no avail. At that point I said screw this. I'm gonna go back to stock before I mess anything up. Flashed stock using MiFlash. Everything is good and dandy except that aforementioned warning message when booting. No matter what I try, I can't get into fastboot to lock the bootloader. Every time I try, it shows that message and boots normally. I've tried using "adb reboot bootloader" it went to the message and boots to OS. I tried holding power and volume up then selecting bootloader. Same result. I tried holding power and volume up then selecting recovery (this is when I realized TWRP was gone. It must have been overwritten when flashing stock firmware) and then reboot to bootloader. Same result. I really don't know what else to try. I guess I could ignore it, but that's really not what I'm looking for.
Click to expand...
Click to collapse
The sticky edl thread has stock b15 with fastboot. Make sure to fully wipe and have stock recovery before attempting to relock.
Sent from my ZTE Axon 7 using Tapatalk

ScottDemon said:
Hello, I've recently been stumped. Last night I attempted to install Lineage OS on my Axon 7 A2017U. I used Axon7Toolkit to unlock the bootloader and install TWRP. This was the first I've seen of the warning from google telling me to lock my bootloader. (My Motorola Nexus 6 never did this) So I ignored it until I had Lineage installed and when I tried to boot, the system was encrypted with a password. The internet said there is no password. I just have to wipe in TWRP. So I tried that to no avail. At that point I said screw this. I'm gonna go back to stock before I mess anything up. Flashed stock using MiFlash. Everything is good and dandy except that aforementioned warning message when booting. No matter what I try, I can't get into fastboot to lock the bootloader. Every time I try, it shows that message and boots normally. I've tried using "adb reboot bootloader" it went to the message and boots to OS. I tried holding power and volume up then selecting bootloader. Same result. I tried holding power and volume up then selecting recovery (this is when I realized TWRP was gone. It must have been overwritten when flashing stock firmware) and then reboot to bootloader. Same result. I really don't know what else to try. I guess I could ignore it, but that's really not what I'm looking for.
Click to expand...
Click to collapse
No, you don't have to WIPE in TWRP, you have to FORMAT DATA! It does roughly the same thing (you lose all your data and internal storage) but since the internal partition is encrypted, it de-encrypts it. To avoid having to lose the internal storage again you just have to flash Magisk or SuperSU right after flashing the ROM (before booting for the first time) and you'll be able to change ROMs with no problem. (but flash magisk right after changing the rom too, of course).
The unlocked bootloader disclaimer is completely normal, however if you're annoyed by it you can get rid of it by following Raystef66's guide called "remove unlocked bootloader inscription".
Happy flashing. Knowing all that, you can go back to Lineage or sth again. Just remember this: If you have access to EDL mode you can get out of the nastiest of bricks. And the A2017U defaults to EDL if there's something seriously wrong. So the U os basically unbrickable
p.s.: NFound's AEX bootloader comes premade so that you won't have the unlocked bootloader inscription. But you have to use one of the Oreo ROMs.
p.p.s.: You can reinstall fastboot and lock but it's just a very bad decision. Just ask if you ever have that sort of trouble, at least I will see it and reply